ULD-360DMX and ULD-360DMX-HP USER`S MANUAL
Contents
1. WWWNNNYFRrR OMAAANNDADAANAANHAH HA HW p nd nd nd nd nd nt jm Endplate Illustration ULD 360DMX HP LED disp DMX In lay A Vv Enter Menu DMX Out O O 0O O Sk a O dO 0 O Se On ON ON O OFF O OFF leprecon ULD Series PUSH Data Out Line B J O Breaker A 1 Introduction The new ULD series dimmer is designed to be a capable and reliable solution for temporary and portable dimming requirements With the menu based interface the dimmer can be configured for different applications including stand alone use without a controller Default values can be restored at any time clearing the internal memory back to the standard values Please take a few minutes to review the specifications and operating features of the ULD 360 dimmer The ULD 360 dimmer is designed for use with conventional incandescent fixtures Transformer loads such as low voltage devices using a step down transformer may require an additional load to be connected to the same circuit to operate properly For operating florescent fixtures see the section regarding Front Panel Controls 2 Specifications Power Connection Unless otherwise indicated your ULD 360 dimmer is designed for connection to standard US pow2. No DMX signal Display shows A Check cable and controller SCR failure Channel stuck at full refer to service center Over Temp Error 02 Check airflow Over Voltage Error 01 Check power wiring Overload breaker trips check wattage of loads If a problem is verified in the dimmer pack contact your Leprecon dealer for service Because of the high voltages present inside of the dimmer it is important that all service be done only by qualified personnel Substandard repairs can create a dangerous condition Warranty Information For a period of two years from the date of sale Leprecon LLC will replace any defective parts and will repair any defective module returned to the factory prepaid without charge for parts or labor Damage caused by misuse incorrect line voltage or connection to shorted loads is not covered under warrany Please consult your dealer for full warranty details The Leprecon service department may be reached at 810 231 9373 during business hours or a message may be left after hours Our fax number is 810 231 1631 Our service department must first authorize any return to the factory Do not return any equipment without calling for an authorization number 8 DMX 512 Information The following information is a summary of the USITT 1990 standard for dimmers and controllers complete copy may be obtained from USITT 10 W 19th ST Suite 5A New York NY 10011 4206 Several web sites exist that have an abun
3. A supplies power for channels 1 3 as well as the internal power supply for the control electronics Line cord and breaker B supplies power to channels 3 through 6 Power applied to the dimmer is indicated by an internal green indicator in each of the breakers If the breaker is on but not lighted there is no power to the line cord Turning on breaker A will also light the red LED display Note The unit can be Reset to original factory settings by depressing and holding the ENTER switch while turning on the first breaker 5 Front Panel Controls The ULD 360 dimmer uses a 4 digit display and four entry switches to set pack functions and display operating status Resetting the ULD 360 to default values The unit can be Reset to original factory settings by depressing and holding the ENTER switch while turning on the first breaker ddress Menu When the dimmer is first turned on the display shows the starting channel address of the ULD 360 This is the DMX address that will control the first channel of the pack When there is no DMX input the channel number is preceded by the letter A for address Enter Menu A Vv oo When valid DMX is detected the letter A is replaced with the letter d for DMX Enter Menu A Vv O O0 O O The UP DOWN keys change the value for the start address The ULD 360 uses the changed value immediately and permanently saves it after 10 seconds or if t
4. ced in the DMX Out connector Termination plugs can be purchased or easily built by installing a 120 ohm resistor between pins 2 and 3 of the 5 pin XLR 3 Installation Mounting The LD360 dimmers are passively cooled using no internal fans The heat generated by the dimmer is dissipated by the extruded metal chassis and the airflow through the chassis vents For this reason mount the dimmer so that air is free to circulate around the dimmer The dimmer should be mounted with at least 12 inches of clearance between the dimmer and any ceiling or obstruction above the dimmer that would block air circulation Power Connection Leprecon LD360 series dimmers are supplied with line cords which have standard Edison plugs attached Each line of the LD360 should be connected to a service capable of supplying 15 amps and protected by a properly sized circuit breaker If you have any questions about the suitability of the power circuit that you intend to use with the LD360 dimmer consult with a qualified electrician Load Connection The LD360 DMX dimmer is offered in several different models Options include stage pin Nema 5 15 duplex and Nema L5 20 Lamp loads are plugged directly into the outlets on the body of the dimmer 4 Turning on Power The ULD 360 has one line cord and circuit breaker and the ULD 360HP has two of each as illustrated previously On the HP model the line cord and breaker to the left on the endplate labeled
5. dance of information regarding DMX 512 As with any Internet information consider the source The DMX 512 standard is designed as a simple reliable system for connecting digital dimmers and controllers The protocol allows up to 512 dimmers to be connected to a single control console With 512 dimmers in a system DMX 512 allows each dimmer level to be updated 44 times each second Connectors The DMX standard specifies the use of 5 pin XLR connectors DMX 512 currently uses 3 pins of the 5 pin connector Pins 4 and 5 are reserved for future use Some manufacturers are using these pins for communications back from the dimmer to the control console or as a redundant data line The connectors to be used for DMX 512 are as follows Console end transmitter Female 5 pin XLR Dimmer end receiver Male 5 pin XLR Some manufacturers of XLR connectors are Switchcraft ITT Cannon and Neutrik Cable type Shielded twisted pair approved for ElA 422 EIA 485 use Either one pair with shield or two pair with shield may be used Examples of such cable are Single pair Belden 9841 Alpha 5271 Two pairs Belden 9842 Alpha 5272 The Pin Designations for DMX 512 are as follows Pin 1 Signal common cable shield Pin 2 Data 1 Pin 3 Data 1 Pin 4 Spare optional Data 2 Pin 5 Spare optional Data 2
6. er systems 120 VAC 60 Hz Lamp connections must be 120 V devices only Line voltages over 135 VAC will trigger the overvoltage protection circuit and shut off the dimmer pack Ambient Temperature The ULD 360 dimmer is designed for use in a cool ventilated area Ambient air temperature must be less than 40 degrees Celsius or about 104 degrees Fahrenheit Power Capacity The ULD360 DMX is unique in the market of small portable dimmers A single breaker is used on the pack instead of individual fuses per each channel As a result the limits of the dimmer are pack limits not channel limits The following guidelines should be followed ULD 360 DMX Pack Limit 15 Amps ULD360 DMX HP Pack Limit 15 Amps per line cord or 30 amps total Control input The ULD 360 DMX accepts DMX 512 1990 as specified by USITT Reliable DMX systems require cable rated for data communication at 250K baud for this reason the use of microphone cable is NOT recommended DMX rated cables are available pre manufactured from your Leprecon dealer For more information on the DMX standard and acceptable cable see the Appendix at the end of this manual For convenience DMX in and out connectors are provided on the ULD 360DMX This allows easy connection to additional dimmer packs The DMX standard allows up to 32 dimmers to be connected to a single DMX controller For proper operation it is recommended that the last dimmer in the system have a termination plug pla
7. he Enter or Menu key is pressed After power on the ULD 360 remains in the Address Menu in its simple interface mode To go to any other menu requires the user to hold the MENU key for about 5 seconds Channel Mode Menu The Channel Mode Menu allows setting the mode of each dimmer channel This mode is indicated by the letter c in the display A W Enter Menu Gg O 0O Set the mode for the displayed channel by pressing the UP DOWN keys The possible channel modes are Mode Description Ln Linear output Standard dimmer channel Nd Non dim Fader input above 60 turns on channel to 100 Input below 40 turns off channel FL Florescent output Dimmer does not begin to turn on until 20 00 FF Fixed output level Values are 0 10 99 and FF FF is 100 output After changing the mode the colon will blink to indicate new data has been entered Press the ENTER key saves the change and advance to the next channel The LD 360 returns to the Address Menu automatically after 4 seconds if no keys are pressed in the Mode Menu Status Menu When the ULD 360 is in the Channel mode pressing MENU again will start the Status mode When Status mode starts the state of each channel will be shown in sequence with the display cycling from Channel 1 to Channel 6 then automatically cycle back to channel 1 This automatic cycling is indicated by the flashing colon The Status Mode first displays the curre
8. lepRecon ULD 360DMX and ULD 360DMX HP USER S MANUAL Copyright Leprecon LLC 2005 All rights reserved Publication 21 1045 Rev C This document is the property of Leprecon LLC and is provided for service and instructional purposes only Possession does not imply or convey rights to use any information herein This information is proprietary and may relate to patents or patents pending that are the properties of CAE Inc other than the use of products manufactured by CAE Inc Table of Contents Endplate Illustration ULD 360DMX HP 1 Introduction 00 cccccecceceeeeeeseeeeees 2 Sp cifications sesisih Power Connection Ambient Temperature Power Capacity Control input istallato Ahead Mounting Renan Power Connection Load Connection Turning on Power Front Panel Controls Resetting the ULD 360 to default values Channel Mode Menu Status MOI 2e uate tn ft ous Configuration Data 6 Error conditions TOOL ICE RSR pide N oN ete Service policy Warranty Information 8 DMX 512 Information CONTE CORES RS eee Cable Dennis
9. nt input state of the dimmer channels 1 6 If valid DMX is present the letter d is displayed followed by the DMX value for the channel Enter Menu A Vv O O If there is no DMX present the d letter will disappear and a will be shown instead Enter Menu A Vv oO OO G Once the input levels for all dimmer channels have been shown the display will then indicate the output level for each channel This is indicated by the letter o in the display followed by channel number followed by output level Output will be shown as a percentage with 100 indicated b the letters FF Pressing the ENTER UP or DOWN keys stops the auto cycle mode and enters manual mode Pressing MENU toggles between auto and manual cycle modes In manual mode the menu steps through its displays when the UP or DOWN keys are pressed The colon is steady in manual mode Enter Menu A Vv yo Oo GO If a channel has been set to a fixed level in the Channel menu the output status will reflect that level In this case the input for channel 1 could be zero but there could be a non zero output level Status Letter Description No input detected DMX is input source Output level Output Fault Overtemp or Overvoltage shutdown nolai Note The unit can be Reset to original factory settings by depressing and holding the ENTER switch while turning on the first breaker Config
10. uration Data If you press the Menu button while in the status display various factory configuration data will be seen These features are not fully defined at this point but include software version power configuration and analog calibration data for the microprocessor 6 Error conditions The ULD 360 will protect itself if the line voltage or operating temperature exceeds safe limits In these cases the dimmer will turn off all channels and display an error message on the display Enter Menu A Vv O O O Error 01 is displayed for an overtemperature condition Error 02 is displayed for an overvoltage condition The dimmer will return to normal operation once the fault is corrected NOTE Extended operation with Overvoltage applied can cause damage to the dimmer power supply 7 Service Service policy The LD360 DMX is designed for a long trouble free life If you suspect that you have a dimmer problem the first step is to check all other system components and connections The easiest test is to substitute a known good dimmer in place of the suspected unit Make sure that the DMX start address is set to the same value Specific problems and solutions are listed below no power breaker not lighted check incoming power No response to DMX Display shows D but Level set in Channel menu no output Clear dimmer and recheck Shorted load breaker trips repair instrument or cable
Download Pdf Manuals
Related Search