Air King 9102 user manual
Contents
1. Crimp Connect 7091854 7091854 Elevation Spring 02090586 Ratchet Plate 02010162B 02010162B Neck Bolt 02090521 02090521 5 16 24 Hex Nut 02090033 02090033 Stand Switch Knob 2010540P 2010131 2010541 2010131 Bottom Plate 2010313 2010315 Power Supply Cord w Plug 02050009FPB 02050009FPB Front Grill 02096217 020962141 Spinner 2010093 2010093 Fan Blade 2010008 2011013 Plastic Nut 2010359P 2010359P 2011200M Plastic Rear Grill 2011212 O1A Rubber Foot Rev F 10 09 2090039 2 crew 8 X 9 16 PPH 2090039 1 20840672. OPERATING INSTRUCTIONS amp PARTS MANUAL OSCILLATING FANS Ventilation Products 12 30 5 cm MODEL 4DA35B 9102B 16 40 6 cm MODEL 4DA36B 9106B READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE INSTALL OPERATE OR MAINTAIN THE PRODUCT DE SCRIBED PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND OR PROPERTY DAMAGE RETAIN INSTRUCTIONS FOR FUTURE REFERENCE DESCRIPTION The Air King 12 30 5 cm and 16 40 6 cm Oscillating Fans feature whisper quiet operation with a 3 paddle blade Fan is powered by a pre lubricated permanent split capacitor motor with a 6 ft 1 8 m 18 3 cord set Fan grills meet OSHA requirements ETL listed SPECIFICATIONS ACTOR codes cectnacttlerans ntand 120V 60Hz 12 30 5 cm 120V 60Hz 16 40 6 cm Blade Size cecscscesseseseseeeeeees 12 30 5 cm Model 4DA35B 9102B 16 40 6 cm Model 4DA36B 91 06B GENERAL SAFETY INFORMATION When using electrical appliances basic pre cautions should always be followed to reduce the risk of fire electric shock and injury to person including the following 1 Read all instructions before using Fan 2 Make certain that the power source conforms to the electrical requirements of the Fan 3 Use this Fan only as described in this manual Any other use not recommended by the manufacturer may cau
3. Where possible avoid the use of extension cords If they must be used minimize the risk of overheating by ensuring that they are UL listed Never use a single extension cord to operate more than one Fan 9 DO NOT operate any Fan with a damaged cord or plug or after the Fan malfunctions has been dropped or damaged in any manner 10 DO NOT insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire or damage the Fan DO NOT block or tamper with the Fan in any manner while it is in operation 11 Always place the Fan on a stable flat level surface when operating to avoid the chance of the Fan overturning Locate the Power Cord so the Fan or other objects are not resting on it DO NOT run Power Cord under carpeting DO NOT cover Power Cord with throw rugs runners or the like Arrange Power Cord away from room traffic and where it will not be tripped over 12 This Fan is NOT intended for use in wet or damp locations Never locate a Fan where it may fall into a bathtub or other water container 13 DO NOT use Fan outdoors 14 This Fanis NOT suitable for use in agricultural facilities including areas where livestock poultry or other animals are confined Please refer to National Electric Code NEC Article 547 7 2008 or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings THIS FAN DOES NOT MEET THE REQUIREMENTS OF
4. NEC ARTICLE 547 7 2008 15 This Fan is NOT suitable for use in hazardous locations Please referto National Electric Code NEC Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 2008 WARNING REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL DEVICES SAVE THESE INSTRUCTIONS 2084067 4DA35B 9102B and 4DA36B 9106B ASSEMBLY 1 Tilt Fan Head back Put Plastic Rear Grill on Motor Figure 1 2 Align Triangular A cut in Plastic Rear Grill with triangular post on top of front Motor cover Fully seat Plastic Rear Grill and secure with Plastic Nut turning Clockwise Figure 2 3 Slide Blade onto Motor Shaft Align groove on blade hub with pin on motor shaft Figure 3 A 4 To secure Blade screw Spinner onto Shaft Counter Clockwise until tight on blade hub ANO 5 With fan head in upright position align Ornament of Front Grill so it is horizontal Insert bottom of Front Grill into Plastic Rear Grill Tab at the bottom of Plastic Rear Grill should fit between spokes of Front Grill Snap Front Grill into Plastic Rear Grill beginning at the top and working down both sides Plastic Blade Rear Grill Plastic Rear Grill Motor Figure 3 OPERATION VARIABLE OSCILLATION Pull oscillation kn
5. ob on the rear of the motor up Turn fan head to left right or straight ahead Push oscil lation knob down and fan will oscillate about the set angle VERTICAL ANGLE To adjust vertical angle tilt fan head up or down as desired SPEED Speed is controlled by a rotary knob 0 Off 3 High 2 Medium 1 Low POWER SUPPLY CORD Plug power supply cord into a wall outlet AC 120Volts 60 Hz MAINTENANCE WARNING ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING THE FAN WARNING DO NOT IMMERSE FAN IN WATER CLEANING Use a soft cloth moistened with a mild soap solu tion such as liquid dish washing detergent Dry ALL PARTS COM PLETELY before reassembling After any maintenance or servicing completely reassemble unit as described in this instruction manual before reconnecting to the power supply CAUTION Do not use gasoline benzine thinner harsh clean ers etc as they will damage the Fan NEVER use ALCOHOL OR SOLVENTS LUBRICATION Precision bearings are sealed at the factory for life and will not require any further lubrication STORAGE Store the Fan with these instructions in a cool dry place SERVICING All other servicing with the exception of general user maintenance should be performed by an authorized service representative REPLACEMENT PART LIST PART NO FOR MODEL DESCRIPTION 4DA35B 9102B 4DA36B 9106B Motor 02035053 02035052 Rotary Switch 02055087 02055087
6. se fire electrical shock or injury to persons 4 Unplug power cord before installing servicing or moving the Fan WARNING DO NOT DEPEND UPON THE ON OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR SERVICING THE FAN ALWAYS UNPLUG THE POWER CORD 5 This Fan must NOT be used in potentially dangerous locations such as flammable explosive chemical laden or wet atmospheres 6 DO NOT use Fan in or near a window Rain may create an electrical hazard 7 The power cord is equipped with a three prong grounded plug that must be inserted into a matching receptacle Under no circumstances should the grounding prong be cut off the plug Where a two prong wall receptacle is encountered it must be replaced with a properly grounded three prong receptacle installed in accordance with the National Electrical Code NEC and all applicable local codes and ordinances This work must be done only by a qualified electrician using copper wire only Rev F 10 09 1 WARNING USE OF A THREE PRONG TO TWO PRONG ADAPTERIS NOT RECOMMENDED IMPROPER CONNEC TION MAY CREATE THE RISK OF ELECTROCUTION USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA WARNING THIS PLUG IS A SAFETY FEATURE TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK AND PERSONAL INJURY DO NOT REMOVE REPLACE REPAIR OR TAMPER WITH THE ORIGINALLY SUPPLIED PLUG IF THE FAN DOES NOT FUNCTION PROPERLY IT MAY BE DUE TO THE SAFETY DEVICE INCORPORATED IN THIS PLUG 8
Download Pdf Manuals
Related Search