Labelmate TWIN-CAT
Contents
1. SPECIFICATIONS Weight of the machine 13 2Kg to 21Kg depending on model Max Label Roll Weight 2 x 5Kg Max Label Roll Diam 220mm Start Stop 2 x ON OFF ON Direction Switches Power Supply Input 220 240VAC 50 60Hz Output 15VDC 4 6A e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e A WARNING This Product is for indoor use only Not for use in wet locations IMPORTANT INFORMATION This product is a label unwinder rewinder It is only to be used to unwind rewind labels of the recommended dimensions and weight in an indoor dry environment The machine has to be unplugged before any manipulation The machine is to be used on a flat surface if the surface is not flat it is to be fixed using the holes in the base plate e Do not leave the power cable in a passageway e The ambient light of the working area needs to be sufficient to avoid any risk e The unwinder rewinder can be used in ambient temperatures of 2 C to 40 C e Connection of the machine to the power source must respect local and European legislations SET UP if you have the ACH Adjustable Core Holder option Skip to step 4 1 STANDARD AND 10 Identify the inner Label Flange Slide the Flange Plate onto the hollow end of the Rewind Shaft For maximum width the Flange face should be flush with the end of the Shaft Tighten the screw in the Hub until it is snug Not too tight CHUCK Mount the inner Flange onto the Quick Chuck with2. two screws provided 3 Slide the Shaft and Flange Assembly onto the TWIN CAT 2 Motor Shafts allowing for clearance to the TWIN CAT 2 Chassis and Motor Screws Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight 4 ACH Slide the Hub of the ACH over the motor Shaft of the TWIN CAT 2 Position the Hub so there is a gap between the ACH Hub and the Rewinder Drive Unit case Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight 5 Set the TWIN CAT 2 in place where you want it 6 CAUTION AVOID ACCIDENTS THE TWIN CAT 2 WEIGHS 13KG AND 21KG SO CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT 7 Verify that the DIRECTION Switches on the TWIN CAT 2 Control Panel is in the OFF position 8 Plug the Power Plug at the end of the wire on the AC Wall Transformer into the TWIN CAT 2 Power Input Jack Plug the AC Transformer into an appropriate AC power outlet The unit is now ready for use A FOR YOUR SAFETY Switch off device before any manipulation LABEL REWINDING The TWIN CAT 2 is bi directional Either Spindle can wind labels in either direction 1 Place the DIRECTION Switches on the TWIN CAT 2 Control Panel in the centre OFF position 2 Slide an empty label core over the desired Core until the core is against the inner Flange Plate On the Quick Chuck tighten the Lock Knob for an ACH see the ACH user manual 3 Feed the label web from the printer and secure it to
3. ED RUN Contact OPEN HALT Pin 1 No connection NOT USED Pin 2 Normally Closed NC contact Pin 3 Normally Closed NC contact return 12V EXT HALT CONT 49K 3 5 mm Jack 1K G 1 27 3 Dual Circuit 10K IS V
4. MAINTENANCE Your TWIN CAT 2 requires no maintenance Product Limited Warranty All Labelmate Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by Labelmate that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer Labelmate reserves all rights to determination of coverage and liability under this warranty The warranty period for all new Labelmate products is outlined below Warranty Period Products Covered Label Rewinders meas Label Unwinders Label Counters mechanical parts only Label Slitters mechanical parts only Label Dispensers Printer Mechanisms Power Supply Modules Counter modules Encoders Any products not specified above The warranty period for all products starts on the date purchased by the original end user customer Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has been modified is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for coverage verification In the event your product requires service please contact the distributor you bought the product from The
5. customer assumes responsibility for all cost and risk incurred in transport for service Labelmate makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person agent or reseller is authorised to give any warranties on behalf of Labelmate Any obligation to warranty other than that specifically addressed above is hereby disclaimed LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmateeurope com LABELMATE User_TWIN CAT 2 CE Original user manual TWIN CAT 2 Dual Spindle Heavy Duty Rewinder Unwinder e Switched Dual Range and Directional Controls x 2 e Constant Adjustable Torque CAT technology e Dual Adjustable Speed Control up to 760mm 30 per second e Dual Variable Torque Control TWIN CAT 2 ACH TWIN CAT 2 with two Quick Chucks and INSP 1 PC 1 Options Remove all parts from the shipping container and verify contents PACKAGE CONTENTS User Manual this document TWIN CAT 2 Drive Unit Power Supply Module Allen Wrench es LABELMATE Quick Chuck Quick Locking Core Chuck or Standard Shaft with three 3 metal Vanes installed or Model 10 INCHES Shaft with six 6 metal Vanes installed or Model ACH Adjustable Core Holder e Flange Plates as appropriate Retain the Shipping Container and Packaging for Storage and Transport
6. the take up roll core with tape Rotate the take up reel a couple of turns 4 Rotate the TORQUE Control Know to the minimum position fully counter clockwise 5 Place each TWIN CAT 2 DIRECTION Switch in the position desired to run left or right 6 Start the printer and adjust the TORQUE Control Knob for the desired take up tension The Upper and Lower Spindles are controlled independently and together can be set to control the rewind unwind tension and speed 7 Use the minimum TORQUE setting needed to rewind labels properly Excessive torque might pull the labels too hard and cause the printer to lose registration WIND IN WIND OUT You can use the Dual Spindles to reverse the direction the labels are facing You can also rewind the labels so that they are in the original serialised order they came out of the printer An optional Adjustable Paper Guide APG CAT can be fitted to help guide the outer edge of the lower label roll as it rewinds EXTERNAL HALT CONTROL An External Halt Control jack on the CAT 3 is for use with external devices capable of providing an open circuit halt command A 3 5mm control cable is necessary for use not included With Pin 2 and Pin 3 of the External Halt Control circuit closed connected together using a 3 5mm dual circuit plug the CAT 3 will operate When the External Circuit is opened the CAT 3 will stop 3 5mm EXTERNAL HALT CONTROL Plug Dual Circuit Plug Contact CLOS
Download Pdf Manuals
Related Search