iColor®Matrix Remover and Slitter User Manual
Contents
1. WARNING The slitter blades are exposed and VERY sharp when the slitter station is in the up position Use extreme caution Slitter module has 3 positions Upper position A the blades are closed to allow the media loading Middle position B align the blades with the edges and the center of the labels tighten the thumb screw once the blade is in position Lower position C the blade cut the media The black knobs lock the slitter module in the requested position Screw the thumb knobs to move the blades to the right or to the left Turn on the MATRIX REMOVER using the power switch on the back Make sure the speed knob is in the slowest position before you switch on the MATRIX REMOVER Slowly turn the speed knob Run the machine until the slit labels reach the bottom of the take up mandrel Remove the labels that have wrapped around the take up mandrel Attach the labels to the core using waste label or tape Note Make sure the tension on all rolls is even If they are not even and you have already attached them to the core you can easily equalize them by loosening the tension knob on the mandrel just a little Now turn each core on the manarel until all label rolls are taut Tighten the knob again Feed the edge waste under the edge waste roller Switch on the MATRIX and slowly turn to increase the speed Evaluate the following areas 1 Matrix Release 2 Matrix2. connector n Keep your hands away from the Matrix Remover at all times while the unit is running n When replacing Slitter blades work from the back blade housing to the front This will minimize the chance of injury since you will not be working over already installed blades a When transporting the unit or any time the unit is not in use always lower the slitter station into the down cut position This will prevent accidental contact with the slitter blades The two rollers below the slitter station act as a guard when the slitter station is in the down position n To prevent fire or shock hazard do not expose the unit to rain or moisture Operate the unit with only proper electrical specifications as labeled on the unit and the AC adapter WARNING HAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY FCC Compliance Statement This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For Users in the United States This product is intended to be supplied by AC DC Power Supply delivered with the machine as for the UL regulation tested and certificated together This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules In a domestic environ
3. Mandrel Wrapping 3 Slitting 4 Finished Cores When the roll is finished the unit automatically stops when the contact on the dancer arm touches the screw on the base You will also hear an audible tone Remove the finished rolls from the take up location Remove the rolls from the take up mandrel Separate the finished rolls Some interleaving may occur This is normal Finally remove the waste matrix mandrel and discard the matrix and the core We do not recommend reusing the same core with matrix from a previous job still attached HOW TO ADD OR REMOVE A BLADE HOLDER Keep out the iron slide bar unscrewing Slide in or out the blade holder the thumb screw Relocate the slide iron bar in its position and rescrew the thumb screw REPLACING SLITTER BLADES Loosen the two screws holding the blade in place Replace the blade e Fix back the screw to holding the blade in place HOW TO ADJUST THE CLUTCH ON UNWINDER It is possible to adjust the clutch by just screwing or loosening the aluminium handle on it more clutch less clutch Paper path A Warnings n The main plug of power supply cord set of AC DC power supply is considered as disconnecting device of equipment n Do not operate the Matrix Remover while wearing loose fitting clothing or neck ties Serious injury may result If clothing or fingers are caught in the rollers immediately disconnect the D C
4. T SOLUTIONS FUR THE LABELING INDUSTRY Label rewinder label unwinder electronic label dispenser and more PRODUCTS LABEL UNWINDER LABEL REWINDER SMALL REEL TO REEL SMALL LABEL LABEL UNWINDER REWINDER LABEL UNWINDER REWINDER UNWINDER REWINDER For VIP Covor VP485 For Epson 1M c3400 3500 LABEL REWINDER SMALL LABEL DISPENSER EASY LABEL DISPENSER Big ELECTRONIC ror LX900 LABEL DISPENSER Scorpio Pius LONGITUDINAL LABEL SLITTER MOTORIZED CORE HOLDER MATRIX REMOVER AND SLITTER DIGITAL LABEL FINISHING SYSTEM UNWINDER REWINDER FOR MORE INFO CONTACT YOUR RESELLER
5. ents ou les doigts sont pris dans les rouleaux appuyez imm diatement deconnectez le connecteur D C n Gardez vos mains loin de la Matrix Remover en tout temps pendant l ex cution de l unit n Lorsque le remplacement des lames de coupeuse travaillent partir du logement de la lame arri re vers l avant Cela r duira les risques de blessures puisque vous travaillerez pas au dessus des lames d j install s n Lors du transport de l unit ou toute fois l unit n est pas dans l utilisation toujours plus faible la station coupeuse en position down coupe Cela emp chera le contact accidentel avec les lames de coupeuse Les deux rouleaux sous la station de coupeuse agissent comme un garde lorsque la station de la coupeuse est dans la position vers le bas n Pour pr venir les risques d incendie ou de choc n exposez pas l unit de la pluie ou l humidit Faire fonctionner l unit avec les sp cifications lectriques que comme marqu sur l unit et l adaptateur ca ATTENTION PIECES DANGEREUSES EN MOUVEMENT N APPROCHEZ PAS LES DOIGTS ET AUTRES PARTIES DU CORPS FCC Compliance Statement This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For Users in the United States This product is intended to be supplied b
6. iColor PRINTING SOLUTIONS powered by UniNet iColor Matrix Remover and Slitter User Manual UniNet 3232 W El Segundo Blvd Hawthorne California 90250 sales icolorprint com www icolorprint com IMPORTANT NOTICE THE MACHINE CAN ALSO BE USED AS SLITTER ONLY WHEN YOU DO THAT PLEASE REMOVE THE TOP MOTORIZED CORE HOLDER AND ADJUST THE CLUTCH KNOB ON THE UNWINDER CORE HOLDER CORE HOLDER on 4 Motorized core holder Non Motorized core holder Use only on unwinder station Waste Matrix Take up mandrel Weeder Motorized Commands Unwinder Supply manarel Non Motorized Tension arm Slitter station Slitter Blade Housing Take up mandrel Motorized Legend MCH MOTORIZED CORE HOLDER Note on Media Environment 50 humidity and 72 degrees Fahrenheit is the optimal conditions for both storage and use of label stock Store label stock in protective plastic wrappings Rewrap partially used stock Do not store stock directly on concrete floors Label stock should be conditioned in this environment for 72 hours prior to use Failure to store media in these conditions may result in media tension problems Too much humidity will cause labels to curl on the edges RUN A JOB WARNING Before starting a new job always make sure the AN waste matrix from the previous job has been removed Do not attach the matrix from a different size label to an existing roll This will cause an uneven
7. ment this product may cause radio Interference In which case the user may be required to take adequate measures This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Use of shielded cables is required to comply with the Class A limits of Part 15 of the FCC Rules You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate and or obtain warranty service for this equipment A Avertissements La prise de l alimentateur AC DC est consider comme partie qui deconnecte l appareil n Ne fonctionnent pas la Matrix Remover tout en portant des v tements l ches ou liens du cou Peuvent entrainer des blessures graves Si les v tem
8. wrap which will cause the material to walk Load the printed and die cut roll on the supply mandrel non motorized Push until it touches roll guide Place an empty wide core on the mandrel motorized Push the core until it touches the core stop Tighten using the tension knob Insert the empty cardboard core on the MCH motorized to receive the new labels roll Set the supply mandrel in the supply location Match the gray handle to gray holder Paper path Pull the printed labels for about fifty centimeters Set the weeder mandrel in the weeder location on the top of the MCH Separate the matrix from liner at this point the matrix to the empty core on the weeder mandrel Insert the MCH into the lower matrix support Continue pulling the printed labels and manually turning the weeder mandrel so that the matrix is wrapped around the core at least once 1 Move the printed label behind the lower MCH 2 Position the empty cardboard core on the single future new labels roll 3 Tighten the roll and the guide in place by turning the tension knob Temporarily attach the label directly to the take up mandrel This will provide the necessary tension in order to start the slitting process Position the blades in between each column and on either edge if desired You can alternate the position of the thumb screw from the top to the side to gain easier access
9. y AC DC Power Supply delivered with the machine as for the UL regulation tested and certificated together This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules In a domestic environment this product may cause radio Interference In which case the user may be required to take adequate measures This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Use of shielded cables is required to comply with the Class A limits of Part 15 of the FCC Rules You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate and or obtain warranty service for this equipment SMAR
Download Pdf Manuals
Related Search