K3HB Series Digital Indicators
Contents
1. TIMING OFF 6 eo input ON Input Peak to peak value Peak to peak hold Measurement value E b1 measurement a1 TIMING ON input OFF High speed Sampling at 50 Times per Second 20 ms Provides an input sampling cycle at least three times faster than earlier models 12 5 times faster for temperature input models at 50 times second see note In addition to im proved response times for judgement output and transfer output average processing can be used to increase the sta bility of measurements Note The K3HB S Linear Sensor Indicator features high speed re sponse of 2 000 times second Sampling at 50 times second Sampling at 15 times second Peak value 96r 100 Timing of internal sampling Timing of internal sampling Time 0 Time Short Body with Depth of Only 95 mm from Behind the Front Panel A short body of only 95 mm see note contributes to the de velopment of slimmer and smaller control panels and instal lations The depth is 100 mm when mounted to the terminal cover Note Depth of DeviceNet models is 97 mm Select a Comparative Output Pattern to Suit the Discrimination or Control Application The output pattern for comparative outputs can be selected In addition to high low comparison with set values output based on level changes is also possible U2. el COMMON COM 1 1 COMMON wl HG Internal circuit d DATA VALID NB RUN A EXT wj Transistor Output Unit os CPE Mia UU s 5 5 E 5 expl i Weel ill ol polarity 4 2400 EL eux Laur FN pL o o 24 VDCt L M7E 01DUN2 01HON2 424 V lt M7E Digital Display Unit DC power Note The BCD output connector pin number is the D sub connector pin number when supply the BCD Output Cable sold separately is connected This number differs from the pin number for the Digital Indicator narrow pitch connector manufactured by Honda Tsushin Kogyo Co Ltd Refer to the following User s Manual for application precautions and other information required when using the Digital Indicator KSHB S X V H Digital Indicator User s Manual Cat No N128 The manual can be downloaded from the following site in PDF format OMRON Industrial Web http www fa omron co jp Digital Indicators KBGHB X V H S 23 OMRON 24 Digital Indicators 5 OMRON E Analog Input Process Indicator Weighing Indicator Temperature Indicator Linear Sensor Indicator KSHB X KSHB H AC voltage only Current input Voltage input Pt 9 S C co e Use terminal pin D6 as the common terminal Models with Terminal Blocks lt K35
3. Equipped with a position meter for monitoring operating status trends External event input allows use in various measurement and discrimina tion applications e Series expanded to include DeviceNet models e Short body with depth of only 95 mm from behind the front panel or 97 mm for DeviceNet models UL certification approval Certification Mark License e CE Marking conformance by third party assessment body Water resistant enclosure conforms to NEMA 4X equivalent to IP66 Capable of high speed sampling at 50 times per second 20 ms Easy to set two point scaling allows conversion and display of any user set values AN Refer to Precautions on page 30 Model Number Structure Model Number Legend Base Units and Optional Boards can be ordered individually or as sets Base Units Base Units with Optional Boards K3HB XU L K3HB XU LLULU L 1 5 1234 5 1 Input Sensor Codes 2 Sensor Power Supply Output Type Codes VD DC voltage input CPA Rela y output PASS SPDT Sensor power supply AD DC current input 12 VDC 10 80 mA See note 1 VA AC voltage input L1A Linear current output DCO 4 20 mA Sensor power supply AA AC current input 12 VDC 10 80 mA See note 2 L2A Linear voltage output DCO 1 5 V 0 to 10 V Sensor power supply 5 Supply Voltage 12 VDC 10 80 mA See note 2 A Sensor power supply 12 VDC 1095 80 mA 100 240 VAC
4. Comparative output L Startup Compensation Timer Measurement can be stopped for a set time using external input Input a n H comparative set value I T 1 v d Time Start artup com H output pensation time 5 set time H input PASS Output Change XVHS Comparative results other than PASS and error signals can be output from the PASS output terminal B Dimensions Character Size for Main Display mm PV display 120 min E e Hie E Terminal cover included Panel Cutout Dimensions SV display DeviceNet models 97 mm Terminal M3 Terminal Cover Accessory 28 Digital Indicators B X V H S E Wiring Precautions For terminal blocks use the crimp terminals suitable for M3 screws e Tighten the terminal screws to the recommended tightening torque of approx 0 5 N m To prevent inductive noise separate the wiring for signal lines from that for power lines Wiring e Use the crimp terminals suitable for M3 screws shown below 1 5 8 mm max Unit Stickers e Select the appropriate units from the unit sticker sheets provided and attach the sticker to the Indicator EIBEIESERRIEES BG min mm rom va mv ma He m min Note When using for meters such as weighing meters use the units speci
5. icators tal Indi K3 H B Series e Aw 1511914 w D Performance TN we j A O a et es c c T T E Zero Features OMRON Red Green Display Allows Easy Recognition of Judgment Results The measurement value display can be set to switch be tween red and green in accordance with the status of com parative outputs This means that the status can be ascertained at a distance Position Meter Enables Easy Monitoring of Operating Status Trends The present value with respect to the measurement or dis play range full scale can be viewed on a bar display The operating status can be grasped intuitively allowing easy judgement of levels and threshold values LEVEL Many Measurement and Discrimination Functions Using External Event Input e Offers a wide variety of application possibilities such detec tion and judgement while synchronizing on an external sig nal Input Sampling hold value Measurement value z Sampling measurement E i gt Time TIMING ON input OFF Input 4 uM _ Peak hold value Measurement L NW NA Peak bottom hold value measurement 5 Bottom hold value T T T 1 1 1
6. 0
7. 1 Pollution degree 2 Overvoltage category II EN61326 1997 A1 1998 A2 2001 EMC EMI 61326 1 industrial applications Electromagnetic radiation interference CISPR 11 Group 1 Class A CISPRL16 1 2 Terminal interference voltage CISPR 11 Group 1 Class A CISPRL16 1 2 EMS 61326 1 industrial applications Electrostatic Discharge Immunity EN61000 4 2 4 kV contact 8 kV in air Radiated Electromagnetic Field Immunity EN61000 4 3 10 V m 1 kHz sine wave amplitude modulation 80 MHz to 1 GHz Electrical Fast Transient Burst Immunity EN61000 4 4 2 kV power line 1 kV I O signal line Surge Immunity EN61000 4 5 1 kV with line power line 2 with ground power line Conducted Disturbance Immunity EN61000 4 6 3 V 0 15 to 80 MHz Voltage Dips and Interruptions Immunity EN61000 4 11 0 5 cycle 0 180 100 rated voltage Note K 100 C or less 2 C 1 digit max U L 2 C 1 digit max B 400 C max Nothing specified R S 200 C max 3 C 1 digit max 0 3 PV or 3 whichever is larger 1 digit max 14 Temperature Indicator KSHB H OMRON E Input Ranges Platinum resistance Thermometer Thermocouple resistance thermometer E 32 Connected terminals ee ee 2300 0 TL 1300 0 en tee BS 400 0 400 0 200 0 200 0 im rw The range shown in dark shading indicates the factory setting Ce
8. 1 gt lt K35 3 gt e Use NPN open collector or no voltage contacts for event input PNP types are also available S TMR D2 ey HOLD D3 RESET D4 ZERO D5 wr Models with Connectors lt K35 2 gt lt K35 4 gt 1 TIMING 2 S TMR 3 HOLD 4 RESET 5 ZERO 6 COM 7 BANK4 8 BANK2 9 BANK1 9 8 JO 10 e Applicable Connector Sold separately XG4M 1030 OMRON e Special Cable Sold separately K32 DICN OMRON XG4M 1030 with 3 m cable BCD Output Cable K32 BCD Pin arrangement Connected device end K3HB end PLC display device etc 38 mm 46 5 mm 210 90 300 POLARITY HH Cover HDR E50LPA5 D sub connector 37 pin female 5 H manufactured by Honda Tsushin Co Ltd Cover 17JE hi 1A de by DDK pos Connector HDR E50MAG1 Connector Equivalent to 17JE 13370 02 5 LL manufactured by Honda Tsushin Co Ltd manufactured by DDK COMMON Stand 17L 002A manufactured by DDK Note The BCD Output Cable has a D sub plug Cover 17JE 37H 1A manufactured by DDK Connector equivalent to 17JE 23370 02 D1 manufactured by DDK Special Cable for Event Inputs with 8 pin Connector Mode Appearance Wiin K32 DICN S TMR HOLD 3 000 mm 3 m Cable marking Digital Indicators B X V H S 25 OMRON B Main Functions Measurement Input Calculation S e Two input circuits are provided The input
9. 100 to 240 VAC FLK1A ape aed d supply 12 VDC 10 80 mA See note 2 24 VAC VDC 24 VACNDC FLK3A Communications RS 485 4 Sensor power supply 12 VDC 10 80 mA See note 2 Optional Board Sensor Power Supply Output Boards 3 Relay Transistor Output Type Codes None None K33 I C1 Relay contact H L SPDT each 2 C2 Relay contact HH H LL L SPST NO each T1 Transistor NPN open collector HH H PASS L LL Relay Transistor Output Boards T2 Transistor PNP open collector HH H PASS L LL BCD BCD output transistor output NPN open collector HH H PASS L LL K34 3 DRT DeviceNet See note 2 Event Input Boards 4 Event input Type Codes None None 35 1 5 points M3 terminal blocks NPN open collector 4 2 8 points 10 pin MIL connector NPN open collector 3 5 points M3 terminal blocks PNP open collector 4 8 points 10 pin MIL connector PNP open collector Note 1 CPA can be combined with relay outputs only 2 Only one of the following can be used by each Digital Indicator RS 232C RS 485 communications a linear output or DeviceNet communications Accessories Sold Separately K32 DICN Special Cable for event inputs with 8 pin connector 32 Special BCD Output Cable 4 Process Indicator K3HB X omnon Specifications E Ratings 85 to 110 of the rated power supply voltage DeviceNet power supply 11 to 25 VDC 100 to 240 V 18 VA max max load See not
10. averaging previous average value comparison forced ze ro zero limit output hysteresis output OFF delay output test teaching display value selection display color selection key protection bank selection display refresh period maximum minimum hold reset AMude Accessories Watertight packing 2 fixtures terminal cover unit stickers instruction manual DeviceNet models also include a DeviceNet connector Hirose HR31 5 08P 5SC 01 and crimp terminals Hirose HR31 SC 121 See note 3 Note 1 DC power supply models require a control power supply capacity of approximately 1 A per Unit when power is turned ON Particular attention is required when using two or more DC power supply models The OMRON S8VS series DC Power Supply Unit is ed 2 PNP input types are also available 3 For K3HB series DeviceNet models use only the DeviceNet Connector included with the product The crimp terminals provided are for Thin Cables Process Indicator 5 OMRON B Characteristics Noise immunity 100 to 240 VAC models 1 500 V at power supply terminals in normal or common mode waveform with 1 ns rising edge and pulse width of 1 us 100 ns 24 VAC VDC models 31 500 V at power supply terminals in normal common mode waveform with 1 ns rising edge and pulse width of 1 us 100 ns Frequency 10 to 55 Hz Acceleration 50 m s 10 sweeps of 5 min each in X Y and Z directions 150 m s 100 m
11. for 1 V applied volt age for the rated load when using a load of 1 N When the ap plied voltage is 10 V the load cell output is 20 mV 2 mV x 10 Weighing Indicator 11 OMRON Temperature Indicator K3JHB H New High speed High precision Temperature Indicator Easy recognition of judgement results using color display that can be switched between red and green Equipped with a position meter for monitoring operating status trends External event input allows use in various measurement and discrimina tion applications e Series expanded to include DeviceNet models e Short body with depth of only 95 mm from behind the front panel or 97 mm for DeviceNet models UL certification approval Certification Mark License e CE Marking conformance by third party assessment body Water resistant enclosure conforms to NEMA 4X equivalent to IP66 e Capable of high speed sampling at 50 times per second 20 ms High resolution of 0 01 C with platinum resistance thermometer Pt100 input Thermocouple sensor inputs also support a resolution of 0 1 C for all ranges Temperature input shift is easily set using two points AN Refer to Precautions on page 30 Model Number Structure Model Number Legend Base Units and Optional Boards can be ordered individually or as sets Base Units Base Units with Optional Boards K3HB HU L 10011 1 5 1234 5 1 Input Senso
12. max Bank input Output ratings Relay output 250 VAC 30 VDC 5 A resistive load depends on the Mechanical life expectancy 5 000 000 operations Electrical life expectancy 100 000 operations model Transistor output Maximum load voltage 24 VDC Maximum load current 50 mA Leakage current 100 uA max Linear output Linear output 0 to 20 mA DC 4 to 20 mA Load 500 max Resolution Approx 10 000 Output error 0 5 FS Linear output 0 to 5 VDC 1 to 5 VDC 0 to 10 VDC Load 5 max Resolution Approx 10 000 Output error 0 5 FS 1 V or less 0 15 V not output for O V or less Display method Negative LCD backlit LED display 7 segment digital display Character height PV 14 2 mm green red SV 4 9 mm green Main functions Scaling function measurement operation selection averaging previous average value comparison zero limit output hysteresis output OFF delay output test display value selection display color selection key protection bank selection display refresh period maximum minimum hold reset Ambient operating temperature 10 to 55 Note 1 DC power supply models require a control power supply capacity of approximately 1 A per Unit when power is turned ON Particular attention is required when using two or more DC power supply models The OMRON S8VS series DC Power Supply Unit is recommended 2 PNP input types are also available 3 For KSHB series DeviceNet models use only the DeviceNet Connect
13. ranges for these circuits can be set independently For example one can be set to 4 to 20 mA and the other can be set to 1 to 5 V e n addition to calculations such as constant A input for one cir cuit it is possible to perform calculations based on the inputs for both circuits such as and A B making it possible to perform thickness measurement and level difference measurement using displacement and length measuring sensors Normal e Continuously performs measurement and always outputs based on comparative results Input H comparative set value Measurement value Time H output Peak Hold Bottom Hold e Measures the maximum or minimum value in a specified period Input Peak hold value Measurement value Bottom hold value Time oso MEN NEMO input OFF Scaling converts input signals in any way required before displaying them The values can be manipulated by shifting inverting or reversing Display value Display value Display value 2 d5P Rz Display value 2 d5P Rz Display value1 r a i Display value 1 i Input value 1 Input value 2 Input value 2 Input value 1 i CAP Ag x ulii Input value CaF Ag CAPA 1 Input value Scaling Teaching Settings for scaling can be made using the present measurement values instead of inputting values with the SHIFT and UP Keys
14. s for relay outputs 3 times each in 3 axes 6 directions Wegm 3009 Degree Memory protection EEPROM non volatile memory Number of rewrites 100 000 Applicable standards UL61010C 1 CSA C22 2 No 1010 1 evaluated by UL EN61010 1 IEC61010 1 Pollution degree 2 Overvoltage category II EN61326 1997 A1 1998 A2 2001 EMI EN61326 A1 industrial applications Electromagnetic radiation interference CISPR 11 Group 1 Class A CISPRL16 1 2 Terminal interference voltage CISPR 11 Group 1 Class A CISPRL16 1 2 EMS 61326 1 industrial applications Electrostatic Discharge Immunity EN61000 4 2 4 kV contact 8 kV in air Radiated Electromagnetic Field Immunity EN61000 4 3 10 V m 1 kHz sine wave amplitude modulation 80 MHz to 1 GHz Electrical Fast Transient Burst Immunity EN61000 4 4 2 kV power line 1 kV I O signal line Surge Immunity EN61000 4 5 1 kV with line power line 2 kV with ground power line Conducted Disturbance Immunity EN61000 4 6 3 V 0 15 to 80 MHz Voltage Dips and Interruptions Immunity EN61000 4 11 0 5 cycle 0 180 100 rated voltage 6 Process Indicator omnon E Input Range Measurement Range and Accuracy CAT Il Input type Range Set value Measurement range Input Accuracy Allowable impedance instantaneous overload 30 s oe re jov D 10001080000V rmi aom 0 0 to 400 0 V 1 min 0
15. 3 rdg 5 700 0 00 to 199 99 V digits max 0 000 to 19 999 V 0 5 rdg 10 400 V 0 0000 to 1 9999 V digits max 20A KSHB XVA AC voltage See note 4 0 0000 to 1 9999 A 0 5 VA CT See note 3 0 00 to 199 99 mA 0 5 rdg 10 2A 0 000 to 19 999 mA cigis max Note 1 The accuracy is for an input frequency range of 40 Hz to 1 kHz except for AD current input A and B ranges and an ambient temperature of 23 5 C The error however increases below 10 of the maximum input value DC voltage input all ranges 10 or less of max input 0 15 FS DC current input all ranges 10 or less of max input 0 1 FS AC voltage input 0 0 to 400 0 10 or less of max input 0 15 FS AC voltage input B 0 00 to 199 99 V 10 or less of max input 0 2 FS AC voltage input C 0 000 to 19 999 V D 0 0000 to 1 9999 V 10 or less of max input 1 0 FS AC current input A 0 000 to 10 000 A 10 or less of max input 0 25 FS AC current input B 0 0000 to 1 9999 A 10 or less of max input 0 5 FS AC current input C 0 00 to 199 99 mA D 0 000 to 19 999 A 10 or less of max input 0 15 FS When DC voltage input models are used with a 1 9999 V range make sure that the connections between input terminals are not open If the input terminals are open the display will show large variations Connect resistance of approximately 1 MQ between the input ter minals if they are open 2 The letters rdg mean readin
16. AX MIN DATA All data High DATA All data High All data High lt 40 ms 1 40 ms 24 ms 24 ms C 64 ms 64 ms DATA DATA VALID VALID 40 ms Ane 30 ms 16 ms The data is set in approximately 30 ms from the rising edge of the Measurement data is output every 64 ms while the REQUEST signal REQUEST signal and the DATA VALID signal is output remains ON nen reading the data from Programmable Note If HOLD is executed when switching between data 1 and data tie DATA VALL dH tums Op 2 either data 1 or data 2 is output depending on the timing of The DATA VALID signal will turn OFF 40 ms later and the data will 9 9 turn OFF 16 ms after that the hold signal The data will not go LOW Programmable Controller REQ 2 DATA including POL and OVER and DATA VALID can be used in a wired OR DATA Cu X X GUX F 3 RUN HH H PASS L and LL are always output with or without a REQUEST signal DATA Do used a wired OR VALID connect for these signals See note See note See note Note Leave 20 ms min between DATA VALID turning OFF and the REQUEST signal Programmable Controller Connection Example Display Unit Connection Example Digital Indicator SYSMAC Programmable Controller Digital Indicator 1 Connector pin No See note
17. NP open collector Note 1 CPA can be combined with relay outputs only 2 Only one of the following can be used by each Digital Indicator RS 232C RS 485 communications a linear output or DeviceNet communications Accessories Sold Separately K32 DICN Special Cable for event inputs with 8 pin connector 32 Special BCD Output Cable 12 Temperature Indicator omnon Specifications E Ratings Power supply voltage 100 to 240 VAC 50 60 Hz 24 VAC VDC DeviceNet power supply 24 VDC Allowable power supply voltage range 85 to 110 of the rated power supply voltage DeviceNet power supply 11 to 25 VDC Power consumption 100 to 240 V 18 VA max max load See note 1 24 VAC DC 11 VA 7 W max max load Current consumption DeviceNet power supply 50 mA max 24 VDC Input Platinum resistance thermometer Pt100 Thermocouple K J T E L 5 W A D conversion method Delta Sigma method External power supply See Sensor Power Supply Output Type Codes Event inputs Timing input NPN open collector or no voltage contact signal See note 2 ON residual voltage 3 V max ON current at 0 17 mA max Max applied voltage 30 VDC max OFF leakage current 1 5 mA max Startup compensa NPN open collector or no voltage contact signal tion timer input ON residual voltage 2 V max ON current at 0 Q 4 mA max Hold input Max applied voltage 30 VDC max Reset input OFF leakage current 0 1 mA
18. PROM non volatile memory Number of rewrites 100 000 Applicable standards UL61010C 1 CSA C22 2 No 1010 1 evaluated by UL EN61010 1 IEC61010 1 Pollution degree 2 Overvoltage category II EN61326 1997 A1 1998 A2 2001 EMC EMI EN61326 A1 industrial applications Electromagnetic radiation interference CISPR 11 Group 1 Class A CISPRL16 1 2 Terminal interference voltage CISPR 11 Group 1 Class A CISPRL16 1 2 EMS EN61326 A1 industrial applications Electrostatic Discharge Immunity EN61000 4 2 4 kV contact 8 kV in air Radiated Electromagnetic Field Immunity EN61000 4 3 10 V m 1 kHz sine wave amplitude modulation 80 MHz to 1 GHz Electrical Fast Transient Burst Immunity EN61000 4 4 2 kV power line 1 kV I O signal line Surge Immunity EN61000 4 5 1 kV with line power line 2 kV with ground power line Conducted Disturbance Immunity EN61000 4 6 3 V 0 15 to 80 MHz Voltage Dips and Interruptions Immunity EN61000 4 11 0 5 cycle 0 180 100 rated voltage E Input Ranges Measurement Ranges and Accuracy Input type Measurement range Indication range Input Accuracy Maximum impedance at 23 5 absolute rated input K3HB SSD 0to20mA 10 000 to 20 000 mA 2 000 to 22 000 mA 120 Q max One input DC voltage current 4to 20 mA 14 000 to 20 000 mA 2 000 to 22 000 mA 0 1 F S 1 digit max 1 000 to 5 000 V 0 500 to 5 500 V 5 000 V 5 500 10 000 V 11 000 V Note The accuracy is for an ambient te
19. R WARRANTY REPAIR OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED STORED INSTALLED AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION ABUSE MISUSE OR INAPPROPRIATE MODIFICATION OR REPAIR Application Considerations B SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards codes or regulations that apply to the combination of products in the custom er s application or use of the products At the customer s request OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product machine system or other application or use The following are some examples of applications for which particular attention must be given This is not intended to be an exhaustive list of all possible uses of the products nor is it intended to imply that the uses listed may be suitable for the products e Outdoor use uses involving potential chemical contamination or electrical interference or conditions or uses not described in this catalog e Nuclear energy control systems combustion systems railroad systems aviation systems medical equipment amusement machines vehicles safety equipment and installations subject to separate industry or government
20. SS L K34 LL 3 DRT DeviceNet See note 2 Event Input Boards 4 Event input Type Codes None None K35 1 5 points M3 terminal blocks NPN open collector 4 2 8 points 10 pin MIL connector NPN open collector 3 5 points M3 terminal blocks PNP open collector 4 8 points 10 pin MIL connector PNP open collector Note 1 CPB can be combined with relay outputs only 2 Only one of the following can be used by each Digital Indicator RS 232C RS 485 communications a linear output or DeviceNet communications Accessories Sold Separately K32 DICN Special Cable for event inputs with 8 pin connector 32 Special BCD Output Cable 8 Weighing Indicator omnon Specifications Ratings 100 to 240 V 18 VA max max load See note 1 24 VAC DC 11 VA 7 W max max load Input e Event inputs Timing input NPN open collector or no voltage contact signal See note 2 ON residual voltage 3 V max ON current at 0 17 mA max Max applied voltage 30 VDC max OFF leakage current 1 5 mA max Startup compensation NPN open oollector or no voltage contact signal timer input ON residual voltage 2 V max ON current at 0 4 mA max applied voltage 30 VDC max OFF leakage current 0 1 mA max Forced zero input Bank input Output ratings depends Relay output 250 VAC 30 VDC 5 A resistive load on the model Mechanical life expectancy 5 000 000 operations Electrical lif
21. This is a convenient function for making the settings while monitoring the operating status Standby Sequence Reverse scaling Sampling Hold e Holds the measurement at the rising edge of the TIMING signal Input Sampling hold value Measurement value 1 1 1 1 1 1 1 1 1 1 1 1 Time TIMING ON input OFF Peak to peak Hold e Measures the difference between the maximum and minimum val ues in a specified period Input Peak to peak value Measurement value TIMING ON input OFF Average Processing S Turns the comparative output OFF until the measurement value enters the PASS range Average processing of input signals with extreme changes or noise smooths out the display and makes control stable Previous Average Value Comparison Slight changes can be removed from input signals to detect only extreme changes Temperature Input Shift H Shifts the temperature input value DIM ee LIE ME TIME SEE M MAC M UE MAMMA c SN EM JS as SS Supported Models The models that support the functions shown here are indi cated by symbols as follows X K3HB X V K3HB V K3HB S E xm em uix Gets nex Qi cuu EM sx dex dee dense denn m uS aei ro tS denn we uc ue deem cec ME cil 26 Digital Indicators B X V H S E Input Compensation Display Forced zero XVS Forces the pr
22. ancy Electrical life 100 000 operations expectancy Linear Output 0 to 20 mA 4 to 20 mA 0to5V 1to5V 0 to 10 V Allowable load impedance 500 max Approx 10 000 Output error 0 5 FS Serial Communications Output BCD Output I O Ratings Input Signal Logic Negative Communications method Half duplex tem Synchronization method Start stop synchronization Input signal Input current for 10 mA no voltage input O signal name Transmission code ASci ON voltage 1 5 V max OFF voltage 3 V min Maximum load 24 VDC POLARITY voltage OVER Maximum load 10 mA DATA VALID current RUN Note For details on serial and DeviceNet communications refer to the Digital Indicator KSHB Communications User s Manual Cat No N129 Leakage current 100 uA max Maximum load 24 VDC Maximum load 50 mA current Leakage current 100 uA max Note For details on serial and DeviceNet communications refer to the Digital Indicator KSHB Communications User s Manual Cat No N129 20 Digital Indicators B X V H S OMRON DeviceNet Communications Communications protocol Conforms to DeviceNet Supported communi Remote I O communications Master Slave connection polling bit strobe COS cyclic cations Conforms to DeviceNet communications standards allocations Allocate any I O data using the Configurator Allocate any data such as DeviceNet specific paramet
23. attention is required when using two or more DC power supply models The OMRON S8VS series DC Power Supply Unit is recommend ed 2 PNP input types are also available 3 For K3HB series DeviceNet models use only the DeviceNet Connector included with the product The crimp terminals provided are for Thin Cables Linear Sensor Indicator 5 17 OMRON B Characteristics Display range 19 999 to 99 999 Sampling period One input 0 5 ms Two inputs 1 0 ms Comparative out Oneinput OFF to ON 1 ms max ON to OFF 1 5 ms max imee Aran istor Two inputs OFF to ON 2 ms max ON to OFF 2 5 ms max outputs Linear output re Oneinput 51 ms max Insulation resistance 20 MQ min at 500 VDC Dielectric strength 2 300 VAC for 1 min between external terminals and case Noise immunity 100 to 240 VAC models 1 500 V at power supply terminals in normal or common mode waveform with 1 ns rising edge and pulse width of 1 us 100 ns 24 VAC VDC models 1 500 V at power supply terminals in normal or common mode waveform with 1 ns rising edge and pulse width of 1 us 100 ns Vibration resistance Frequency 10 to 55 Hz Acceleration 50 m s 10 sweeps of 5 min each in X Y and Z directions Shock resistance 150 m s 100 m s for relay outputs 3 times each in 3 axes 6 directions Degree of protec Conforms to NEMA 4X for indoor use equivalent to IP66 tion IPOO finger protection VDE0106 100 Memory protection EE
24. e 1 24 VAC DC 11 VA 7 W max max load ipt A D conversion method Delta Sigma method External power supply See Sensor Power Supply Output Type Codes Event inputs See Timing input NPN open collector or no voltage contact signal note 2 ON residual voltage 3 V max ON current at 0 17 mA max Max applied voltage 30 VDC max OFF leakage current 1 5 mA max Startup compensa NPN open collector or no voltage contact signal tion timer input ON residual voltage 2 V max ON current at 0 4 mA max Reset i t Max applied voltage 30 VDC max OFF leakage current 0 1 mA max Output ratings de Relay output 250 VAC 30 VDC 5 A resistive load pends on the mod Mechanical life expectancy 5 000 000 operations Electrical life expectancy 100 000 operations Transistor output load voltage 24 VDC Maximum load current 50 mA Leakage current 100 max Linear output Linear output 0 to 20 mA DC 4 to 20 mA Load 500 max Resolution Approx 10 000 Output error 0 5 FS Linear output 0 to 5 VDC 1 to 5 VDC 0 to 10 VDC Load 5 kQ max Resolution Approx 10 000 Output error 0 5 FS 1 V or less 0 15 V not output for V or less Display method Negative LCD backlit LED display 7 segment digital display Character height PV 14 2 mm green red SV 4 9 mm green Scaling function measurement operation selection
25. e Input 0 5 ms 0 5 ms 0 5 ms SS mm Data processing time D Output response time 777777 See note Two Inputs 0 5 ms 0 5 ms 0 5 ms 0 5 ms Data processing time D Output response time 7755 7 See note l L8 JL 1 Note For transistor outputs For one input OFF to ON 1 ms and ON to OFF 1 5 ms For two inputs OFF to ON 2 ms and ON to OFF 2 5 ms For relay outputs The relay operation time of 15 ms is added to the transistor output response times Linear Sensor Indicator 5 19 omnon Common Specifications E Event Input Ratings Input type S TMR HOLD RESET ZERO BANK1 BANK2 TIMING BANKA ON 1 max OFF 100 min ON residual voltage 2 V max ON residual voltage 3 V max OFF leakage current 0 1 mA max OFF leakage current 1 5 mA max Load current 4 mA max Load current 17 mA max Maximum applied voltage 30 VDC max Maximum applied voltage 30 VDC max E Output Ratings Contact Output Transistor Output Resistive loads Inductive loads Maximum load voltage 24 VDC 0 VDC L R 0 ms cireuit cosde0 4 Maximum load current 50mA 11 30 VDC L R 0 ms circuit 0 4 Maximum load current 50 mA 30 VDC L R 7 ms Leakage current 100 uA max Rated load 5 A at 250 VAC 1A at 250 VAC 5 A at 30 VDC 1 at 30 VDC Rated through 5A current Mechanical life 5 000 000 operations expect
26. e expectancy 100 000 operations Transistor output Maximum load voltage 24 VDC Maximum load current 50 mA Leakage current 100 uA max Linear output Linear output 0 to 20 mA DC 4 to 20 mA Load 500 max Resolution Approx 10 000 Output error x0 596 FS Linear output 0 to 5 VDC 1 to 5 VDC 0 to 10 VDC Load 5 max Resolution Approx 10 000 Output error 0 5 FS 1 V or less 0 15 V not output for O V or less Display method Negative LCD backlit LED display 7 segment digital display Character height PV 14 2 mm green red SV 4 9 mm green un RN Scaling function measurement operation selection averaging previous average value comparison forced zero zero limit output hysteresis output OFF delay output test teaching display value selection display color selection key protection bank selection display refresh period maximum minimum hold reset Watertight packing 2 fixtures terminal cover unit stickers operation manual DeviceNet models also include a DeviceNet connector Hirose HR31 5 08P 5SC 01 and crimp terminals Hirose HR31 SC 121 See note 3 Note 1 DC power supply models require a control power supply capacity of approximately 1 A per Unit when power is turned ON Particular attention is required when using two or more DC power supply models The OMRON S8VS series DC Power Supply Unit is ed 2 PNP input types are also available 3 F
27. e the power supply terminals and AWG28 cross section 0 081 mm to AWG16 cross section 1 309 mm for other terminals Length of exposed wire 6 to 8 mm 9 order to prevent inductive noise wire the lines connected to the product separately from power lines carrying high voltages or cur rents Do not wire in parallel with or in the same cable as power lines Other measures for reducing noise include running lines along separate ducts and using shield lines 10 Ensure that the rated voltage is achieved no longer than 2 s after turning the power ON 11 Allow the product to operate without load for at least 15 minutes after the power is turned ON 12 Do not install the product near devices generating strong high fre quency waves or surges When using a noise filter check the volt age and current and install it as close to the product as possible 13 Do not use thinner to clean the product Use commercially avail able alcohol 14 Be sure to confirm the name and polarity for each terminal before wiring the terminal block and connectors 15 Use the product within the noted supply voltage and rated load 16 Do not connect anything to unused terminals 17 Output turns OFF when the mode is changed or settings are ini tialized Take this into consideration when setting up the control System 18 Install an external switch or circuit breaker that complies with applicable IEC60947 1 and IEC60947 3 requirements and label them clea
28. ector PNP open collector Note 1 CPA can be combined with relay outputs only 2 Only one of the following can be used by each Digital Indicator RS 232C RS 485 communications a linear output or DeviceNet communications Accessories Sold Separately K32 DICN Special Cable for event inputs with 8 pin connector K32 BCD Special BCD Output Cable 16 Linear Sensor Indicator 5 Specifications OMRON Ratings Power supply voltage Allowable power supply voltage range Power consumption See note 1 Current consumption Input A D conversion method External power supply Event inputs See note 2 Timing input Startup compensa tion timer input Hold input Reset input Forced zero input Bank input Output ratings de pends on the model Relay output Transistor output Linear output Display method Main functions Ambient operating temperature Ambient operating humidity Storage temperature Altitude Note 1 100 to 240 VAC 50 60 Hz 24 VAC VDC DeviceNet power supply 24 VDC 85 to 110 of the rated power supply voltage DeviceNet power supply 11 to 25 VDC 100 to 240 V 18 VA max max load 24 VAC DC 11 VA 7 W max max load DeviceNet power supply 50 mA max 24 VDC DC voltage current Sequential comparison system See Sensor Power Supply Output Type Codes NPN open collector or no voltage contact signal ON residual voltage 3 V max ON current at 0 Q 17 mA ma
29. ency stop circuits interlock circuits or limit circuits to ensure safety in the system if an abnormality occurs due to malfunction of the product or another external factor affecting the product s operation e N CAUTION Do not allow pieces of metal wire clippings or fine metallic shavings or filings from installation to enter the product Doing so may occasionally result in minor electric shock fire or malfunction Do not use the product in locations where flammable or explosive gases are present Doing so may occasionally result in explosion causing minor or moderate injury or property damage Do not attempt to disassemble repair or modify the product Doing so may occasionally result in minor or moderate injury due to electric shock Do not use the equipment for measurements within Measurement Categories 1 and IV for KSHB X and Il III and IV for KSHB S and according to IEC61010 1 Doing so may occasionally cause unexpected operation resulting in minor or moderate injury or damage to the equipment Use the equipment for measurements only within the Measurement Category for which the product is designed Perform correct setting of the product according to the application Failure to do so may occasionally cause unexpected operation resulting in minor or moderate injury or damage to the equipment Ensure safety in the event of product failure by taking safety measures such as
30. ers and variable area for Digital Indicators Input area 2 blocks 60 words max Output area 1 block 29 words max The first word in the area is always allocated for the Output Execution Enabled Flags Message communications Explicit message communications CompoWay F communications commands can be executed using explicit message communications Connection methods Combination of multi drop and T branch connections for trunk and drop lines DeviceNet 500 250 or 125 Kbps automatic follow up Special 5 wire cable 2 signal lines 2 power supply lines 1 shield line Communications distance Baud rate Network length Drop line length Total drop line max max length max 500 Kbps 100 m 100 39 250 Kbps 100m 6m 78m 250 m 125 Kbps 100m 6m 156m 500 m The values in parentheses are for Thick Cable Communications power supply 24 VDC DeviceNet power supply 11 to 25 VDC DeviceNet power supply 80 mA 24 VDC 64 DeviceNet Configurator is counted as one node when connected 63 ORC errors DeviceNet power supply Supplied from DeviceNet communications connector B Internal Block Diagram Analog input m m a D O Indications BCD I O 2 Drive Transistor ig circuit output x x Event input Ny Waveform Drive N shaping circuit circuit X Relay output z Drive Drive Linear output K
31. esent value to 0 Convenient for setting reference val ues or deducting tares for weight measurement VS Shifts the current value measured with a forced zero to O again It is possible to measure two or more compounds separately and then by releasing the tare zero and forced zero measure the combined total XVHS Zero trimming Compensates for mild fluctuations in input signals due to factors such as sensor temperature drift based on OK PASS data at mea surement This function can be used with sampling hold peak hold or bottom hold XVHS Changes the display value to O for input values less than the set value It is enabled in normal mode only This function can be used for example to stop negative values being displayed or to eliminate flickering and minor inconsistencies near O Display Zero limit setting Display Refresh Period X The display refresh period can be lengthened to reduce flickering and thereby make the display easier to read Display Color Selection Values can be displayed in either red or green With comparative out put models the display color can also be set to change according to the status of comparative outputs e g green to red or red to green OMRON The current display value can be selected from the present value the maximum value and the minimum value It is possible to specify i e restrict the values that the smallest dis played digit can cha
32. fied by regulations on weights and measures omnon E Mounting Method 1 Insert the K3HB into the mounting cutout in the panel 2 Insert watertight packing around the Unit to make the mounting watertight Watertight packing 3 Insert the adapter into the grooves on the left and right sides of the rear case and push until it reaches the panel and is fixed in place 7 4 h 7 h h 7 4 4 4 7 2 7 4 4 4 4 4 4 4 4 7 h 7 4 2 4 B LCD Field of Vision The is designed to have the best visibility at the angles shown in the following diagram E Waterproof Packing The waterproof packing ensures a level of waterproofing that con forms to NEMA 4X Depending on the operating environment deteri oration contraction or hardening may occur and replacement may be necessary In this case consult your OMRON representative Digital Indicators KBGHB X V H S 29 OMRON B Precautions NWARNING Do not touch the terminals while power is being supplied Doing so may possibly result in electric shock Make sure that the terminal cover is installed before using the product Always provide protective circuits in the network Without protective circuits malfunctions may possibly result in accidents that cause serious injury or significant property damage Provide double or triple safety measures in external control circuits such as emerg
33. g and refer to the input error 3 The value 0 5 VA CT is the VA consumption of the internal CT current transformer ER K3HB XAA A 0 000 to 10 000 A 0 5 VA CT 0 5 rdg 20 AC current See note 3 digits max I o ER 1 9999 V 4 The 11 complies with UL standards when the applied input voltage is within the range to 150 VAC If the input voltage is higher than 150 VAC install an external transformer or take other measures to drop the voltage to 150 VAC or lower Process Indicator 7 OMRON Weighing Indicator K3HB V An Ideal Indicator for OK NG Judgements in Automated and Picking Machines Measuring Factors such as Pressure Load Torque and Weight Using Load Cell Signal Input Easy recognition of judgement results using color display that can be switched between red and green Equipped with a position meter for monitoring operating status trends External event input allows use in various measurement and discrimina tion applications e Series expanded to include DeviceNet models e Short body with depth of only 95 mm from behind the front panel or 97 mm for DeviceNet models UL certification approval Certification Mark License e CE Marking conformance by third party assessment body Water resistant enclosure conforms to NEMA 4X equivalent to IP66 Capable of high speed sampling at 50 times per second 20 ms Easy t
34. h Optional Boards K3HB SU L K3HB SU UUU L 1 5 1234 5 1 Input Sensor Codes 2 Sensor Power Supply Output Type Codes FOEDE Proces Ipu CPA Relay output PASS SPDT Sensor power supply 5 Supply Voltage 12 VDC 10 80 mA See note 1 L1A Linear current output 4 20 mA Sensor power supply 100 240 VAC 100 to 240 VAC 12 VDC 10 80 mA See note 2 24 VAC VDC 24 VAC VDC L2A Linear voltage output DCO 1 5 V 0 to 10 V Sensor power supply 12 VDC 10 80 mA See note 2 A Sensor power supply 12 VDC 10 80 mA FLK1A Communications RS 232C Sensor power supply 12 VDC 10 80 mA See note 2 FLK3A Communications RS 485 Sensor power supply 12 VDC 10 80 mA See note 2 Optional Board Sensor Power Supply Output Boards 3 Relay Transistor Output Type Codes None None K33 I C1 Relay contact H L SPDT each 2 C2 Relay contact HH H LL L SPST NO each T1 Transistor NPN open collector HH H PASS L LL Relay Transistor Output Boards T2 Transistor PNP open collector HH H PASS L LL BCD BCD output transistor output NPN open collector HH H PASS L LL K34 DRT DeviceNet See note 2 3 4 Event input Type Codes Event Input Boards None None 1 5 points M3 terminal blocks NPN open collector K 2 8 points 10 pin MIL connector NPN open collector 35 _ 3 5 points M3 terminal blocks open collector 4 4 8 points 10 pin MIL conn
35. i E circuit E DeviceNet Sensor power supply 1 Drive Communr Filter circuit cations Communications SK driver MORTE hA J Vcom Vo pe pe Converter isolated Power supply Digital Indicators B X V H S 21 OMRON Power Supply Derating Curve for Sensor Reference Value With 12 V Max current mA Ambient temperature C With 10 V Max current mA Ambient temperature C Note 1 The above values are for standard mounting The derating curve differs depending on the mounting conditions 2 Do not use the Sensor outside of the derating area i e do not use it in the area labeled 1 in the above graphics Doing so may occa sionally cause deterioration or damage to internal components E Component Names and Functions Max Min status indicator Turns ON when the maximum value or minimum value is displayed in the RUN level Level bank display In RUN level displays the bank if the bank function is ON Turns OFF if the bank function is OFF In other levels displays the current level Comparative output status indicators Display the status of comparative outputs Status indicators Turns ON when the tare zero function is T ZH executed Turns OFF if it is not executed or is cleared Turns ON when the forced zero function is Zero executed Turns OFF if it is no
36. installing a separate monitoring system Product failure may occasionally prevent operation of comparative outputs resulting in damage to the connected facilities and equipment Tighten the screws on the terminal block and the connector locking screws securely using a tightening torque within the following ranges Loose screws may occasionally cause fire resulting in minor or moderate injury or damage to the equipment Terminal block screws 0 43 to 0 58 N m Connector locking screws 0 18 to 0 22 N m Make sure that the product will not be adversely affected if the DeviceNet cycle time is lengthened as a result of changing the program with online editing Extending the cycle time may cause unexpected operation occasionally resulting in minor or moderate injury or damage to the equipment Before transferring programs to other nodes or changing I O memory of other nodes check the nodes to confirm safety Changing the program or I O memory of other nodes may occasionally cause unexpected operation resulting in minor or moderate injury or damage to the equipment gt bP OO OOO Precautions for Safe Use 1 Do not use the product in the following locations Locations subject to direct radiant heat from heating equipment Locations where the product may come into contact with water oil ocations subject to direct sunlight Locations where dust or corrosive gases in particular sulfuric or ammonia gas are
37. lsius Fahrenheit Correlation Values and Setting Specified Ranges input type ERN NEM NES NER ct E R 991709 oowoo 17001018700 30013300 B 30 500 3013x090 7001019700 1001034900 _ D 850 0 Ed a a E 150 00 E 200 0 PEE 0 200 0 0 Temperature Indicator 15 OMRON Linear Sensor Indicator K3HB S A Linear Sensor Indicator Capable of High speed Response at 2 000 Times per Second Effective for high speed measurement and discrimination with a sam pling period of 0 5 ms and output response time of 1 ms max Easy recognition of judgement results using color display that can be switched between red and green Equipped with a position meter that represents measured amounts and relative positions Zero calibration can be performed easily with the forced zero function e Series expanded to include DeviceNet models e Short body with depth of only 95 mm from behind the front panel or 97 mm for DeviceNet models UL certification approval Certification Mark License e CE Marking conformance by third party assessment body Water resistant enclosure conforms to NEMA 4X equivalent to IP66 AN Refer to Precautions on page 30 Model Number Structure E Model Number Legend Base Units and Optional Boards can be ordered individually or as sets Base Units Base Units wit
38. mperature of 23 5 0 2 F S 1 digit max input 0 000 to 5 000 V 0 500 to 5 500 mA Two inputs 18 Linear Sensor Indicator 5 Input type DC current input Connected terminals 0 20 4 22 Input type Connected terminals nput B un tb DC current range mA The range shown in dark shading indicates the factory setting DC voltage range V Sampling and Comparative Output Response Times The K3HB S sampling and comparative output response times depend on the calculation methods timing hold type and for simple averaging the averaging times Refer to the following description for details Bl Output Refresh Period The 5 repeats input reads calculation and judgement output processing The output refresh period differs depending on whether there are one or two inputs as outlined below One Input 0 5 ms 0 5 ms 0 5 ms Input Input Input Input Input Input d 1 1 or I T T Output Output Output Output Output Input read Every 0 5 ms Output Every 0 5 ms Two inputs 0 5 ms 0 5 ms 0 5 ms Input Input Input Input Input Input Input Emo pu jeu nput A or Input B Output Output Output Output Output Output Input A Every 1 ms Input read Input B Every 1 ms Output Every 0 5 ms E Output Response Time The comparative output response time is the sum of the data pro cessing time and the output relay or transistor response time On
39. nge by For example if the setting is 2 the small est digit will only take the values 0 2 4 6 or 8 and if the setting is 5 it will only take the values O or 5 If the setting is 10 it will only take the value of 0 Digital Indicators B X V H S 27 OMRON E Output Comparative Output Pattern The output pattern for comparative outputs can be selected In addi tion to high low comparison with set values output based on level changes is also possible Use the type of output pattern appropriate for the application Compre Standard Output Measurement conte Level Output conte uL uu ENDE selva Comparative Lower Comparative au set value LL Output HH ON Output HH Output H F Output H OutputPASS Output PASS To Output L Output L 0 __ Output LL set value LL ON OFF Measurement value Higher Lower Zone Output Comparative set value HH Comparative set value H Comparative set value L Comparative set value LL Output HH Output H Output PASS Output L m pD Output LL Am o Q e Heverses the output operation of comparative outputs for compara tive results MM Prevents comparative output chattering when the measurement value fluctuates slightly near the set value Example Comparative Output Pattern Standard Output Hysteresis Comparative set value H T CX 9 Comparative set value L 3
40. o set two point scaling allows conversion and display of any user set values AN Refer to Precautions on page 30 Model Number Structure Model Number Legend Base Units and Optional Boards can be ordered individually or as sets Base Units Base Units with Optional Boards K3HB VUL 4 1 1 5 1234 5 1 Input Sensor Codes 2 Sensor Power Supply Output Type Codes LC Load cell input DC low voltage input CPB Relay output PASS SPDT Sensor power supply 10 VDC 5 100 mA See note 1 9 Supply Voltage L1B Linear current output DCO 4 20 mA Sensor power supply 100 240 VAC 100 to 240 VAC T 10 biis Verde 295 Linear voltage outpu 5V 0to Sensor power supply 24 24 VAC VDC 10 VDC 100 2 B Sensor power supply 10 VDC 5 100 mA FLK1B Communications RS 232C Sensor power supply 10 VDC 5 100 mA See note 2 FLK3B Communications RS 485 Sensor power supply 10 VDC 5 100 mA See note 2 Optional Board Sensor Power Supply Output Boards 3 Relay Transistor Output Type Codes None None K33 I C1 Relay contact H L SPDT each 2 C2 Relay contact HH H LL L SPST NO each T1 Transistor NPN open collector HH H PASS L LL Relay Transistor Output Boards T2 Transistor PNP open collector HH H PASS L LL BCD BCD output transistor output NPN open collector HH H PA
41. or K3HB series DeviceNet models use only the DeviceNet Connector included with the product The crimp terminals provided are for Thin Cables Weighing Indicator 9 OMRON B Characteristics 2 300 VAC for 1 min between external terminals and case Noise immunity 100 to 240 VAC models 1 500 V at power supply terminals in normal or common mode waveform with 1 ns rising edge and pulse width of 1 us 100 ns 24 VAC VDC models 1 500 V at power supply terminals in normal or common mode waveform with 1 ns rising edge and pulse width of 1 us 100 ns Frequency 10 to 55 Hz Acceleration 50 m s 10 sweeps of 5 min each in X Y and Z directions 150 m s 100 m s for relay outputs 3 times each in 3 axes 6 directions Wegm 3009 Base OOOO O Degree of Memory protection EEPROM non volatile memory Number of rewrites 100 000 Applicable standards UL61010C 1 CSA C22 2 No 1010 1 evaluated by UL EN61010 1 IEC61010 1 Pollution degree 2 Overvoltage category II EN61326 1997 A1 1998 A2 2001 EMC EMI EN61326 A1 industrial applications Electromagnetic radiation interference CISPR 11 Group 1 Class A CISPRL16 1 2 Terminal interference voltage CISPR 11 Group 1 Class A CISPRL16 1 2 EMS EN61326 A1 industrial applications Electrostatic Discharge Immunity EN61000 4 2 4 kV contact 8 kV in air Radiated Electromagnetic Field Immunity EN61000 4 3 10 V m 1 kHz sine wave amplitude modulation 80 MH
42. or included with the product The crimp terminals provided are for Thin Ca bles Temperature Indicator 13 OMRON B Characteristics Accuracy Thermocouple input 0 3 PV or 1 C whichever is larger 1 digit max See note Platinum resistance thermometer input 0 2 PV or 0 8 C whichever is larger 1 digit max Sampling period 20 ms 50 times second Comparative output response time Platinum resistance thermometer input range 120 ms max Thermocouple input range 180 ms max Linear output response time Platinum resistance thermometer input range 170 ms max Thermocouple input range 230 ms max Insulation resistance 20 min at 500 VDC Dielectric strength 2 300 VAC for 1 min between external terminals and case Noise immunity 100 to 240 VAC models 1 500 V at power supply terminals in normal common mode waveform with 1 ns rising edge and pulse width of 1 us 100 ns 24 VAC VDC models 1 500 V at power supply terminals in normal common mode waveform with 1 ns rising edge and pulse width of 1 us 100 ns Frequency 10 to 55 Hz Acceleration 50 m s 10 sweeps of 5 min each in X Y and Z directions 150 m s 100 m s for relay outputs 3 times each in 3 axes 6 directions Wegm 3009 Base OOOO O Degree of pro Memory protection EEPROM non volatile memory Number of rewrites 100 000 Applicable standards UL61010C 1 CSA C22 2 No 1010 1 evaluated by UL EN61010 1 IEC61010
43. present Locations subject to extreme temperature changes Locations where icing or condensation may occur ocations subject to excessive shocks or vibration 2 Do not use the product in locations subject to temperatures or humidity levels outside the specified ranges or in locations prone to condensation If the product is installed in a panel ensure that the temperature around the product not the temperature around the panel does not go outside the specified range 3 Provide sufficient space around the product for heat dissipation 4 Use and store the product within the specified temperature and humidity ranges If several products are mounted side by side or arranged in a vertical line the heat dissipation will cause the inter nal temperature of the products to rise shortening the service life If necessary cool the products using a fan or other cooling method 5 The service life of the output relays depends on the switching capacity and switching conditions Consider the actual application conditions and use the product within the rated load and electrical service life Using the product beyond its service life may result in contact welding or burning 6 Install the product horizontally Mount to a panel between 1 and 8 mm thick 8 Use the specified size of crimp terminals M3 width 5 8 mm max for wiring To connect bare wires use AWG22 cross sec tion 0 326 mm to AWG14 cross section 2 081 mm to wir
44. r Codes 2 Sensor Power Supply Output Type Codes TA Temperature input None None Thermocouple input Platinum resistance thermometer input CPA Relay output PASS SPDT Sensor power supply 5 Iv Voltaae 12 VDC 10 80 mA See note 1 Supply 9 L1A Linear current output c 20 pa Sensor power supply 100 240 VAC 100 to 240 VAC 12 VDO 10 80 mA See note L2A Linear voltage output DCO 1 5 V O to 10 V Sensor power supply 24 VAC VDC 24 VAC VDC 12 VDC 10 80 mA See note 2 A Sensor power supply 12 VDC 10 80 mA FLK1A Communications RS 232C Sensor power supply 12 VDC 10 80 mA See note 2 FLK3A Communications RS 485 Sensor power supply 12 VDC 10 80 mA See note 2 Optional Board Sensor Power Supply Output Boards 3 Relay Transistor Output Type Codes None None 33 1 C1 Relay contact H L SPDT each 2 C2 Relay contact HH H LL L SPST NO each Relay Transistor Output Boards 1 Transistor NPN open collector HH H PASS L LL T2 Transistor PNP open collector HH H PASS L LL BCD BCD output transistor output NPN open collector HH H PASS K34 _ L LL 3 DRT DeviceNet See note 2 Event Input Boards 4 Event input Type Codes None None K35 1 5 points terminal blocks NPN open collector 4 2 8 points 10 pin MIL connector NPN open collector 3 5 points M3 terminal blocks open collector 4 8 points 10 pin MIL connector P
45. regulations e Systems machines and equipment that could present a risk to life or property Please know and observe all prohibitions of use applicable to the products NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM ALL DIMENSIONS SHOWN ARE IN MILLIMETERS To convert millimeters into inches multiply by 0 03937 To convert grams into ounces multiply by 0 03527 Cat No N131 E1 04 the interest of product improvement specifications are subject to change without notice OMRON Corporation Industrial Automation Company OMRON ELECTRONICS LLC OMRON CHINA CO LTD 1 East Commerce Drive Schaumburg IL Room 2211 Bank of China Tower Control Devices Division H Q 60173 200 Yin Cheng Road M Analog Controller Division U S A Shanghai 200120 China Shiokoji Horikawa Shimogyo ku Tel 1 847 843 7900 Fax 1 847 843 8568 Tel 86 21 5037 2222 Fax 86 21 5037 GON Pa apan OMRON ASIA PACIFIC PTE LTD 2200 Tel 81 75 344 7080 Fax 81 75 344 7189 83 Clemenceau Avenue OMRON EUROPE B V 1111 01 UE Square Wegalaan 67 69 NL 2132 JD Hoofddorp 239920 Singapore The Netherlands Tel 65 6835 301 1 Fax 65 6835 2711 Tel 31 2356 81 300 Fax 31 2356 81 388 Printed in Japan 0805 1M 0104
46. rly so that the operator can quickly turn OFF the power 19 Use the specified cables for the communications lines and stay within the specified DeviceNet communications distances Refer to the Users Manual Cat No N129 for details on communica tions distance specifications and cables 20 Do not pull the DeviceNet communications cables with excessive force or bend them past their natural bending radius 30 Digital Indicators 5 OMRON 21 Do not connect or remove connectors while the DeviceNet power is being supplied Doing so will cause product failure or malfunc tion 22 Use cables with a heat resistance of 70 C min B Noise Countermeasures 1 Do not install the product near devices generating strong high fre quency waves or surges such as high frequency welding and sewing machines 2 Mount a surge suppressor or noise filter to peripheral devices generating noise in particular motors transformers solenoids and magnet coils Line filter 5 A Digital Digital 2 o Indicator S Indicator o CUI m 5 LG Surge suppressor LT oc 3 In order to prevent inductive noise wire the lines connected to the terminal block separately from power lines carrying high voltages or currents Do not wire in parallel with or in the same cable as power lines Other measures for reducing noise include running lines along separate ducts and using shield lines Example of Coun
47. se the type of out put pattern appropriate for the application Depth 95 mm See note Standard Output Measurement Level Output Measurement value Higher tive set value HH Higher Comparative set value H Comparative set value L Lower Comparative set value LL Lower Output HH ON Output HH ON Output H OFF Output H OFF Output PASS Output PASS Output L Output L OutputLL 1 Output LL Measurement value Zone Output Higher Lower Output Output OFF Output PASS Output L OutputlL Note The HH H L or LL outputs must be set in that order for the zone outputs to output correctly This is because the comparative set values and outputs for standard and level outputs are in a 1 to 1 relationship whereas the meaning of zone outputs depends on the settings of all the comparative set values Lineup Includes DeviceNet Models Enabling High speed Data Communications with PLCs without Special Programming e DeviceNet compliance enables high speed data transmis sion by allocating setting and monitoring parameters in the memory of the PLC This capability greatly reduces labor spent in developing communications programs Ethernet K3HB Digital Indicators DeviceNe
48. t Configurator 2 Digital Indicators Series Analog Input Series OMRON Note The applications provided in this catalog are intended as reference only Do not attempt to use any of them in real systems without first con firming machine and device functions and safety For applications that require safety ensure that there is sufficient leeway in ratings and performances install fail safe measures and take any other safety measures required by the application In addition contact your nearest OMRON representative and confirm specifications K3HB series Product Lineup E K3HB X Process Indicator page 4 Indicates Measurements for Voltage Current Signals DC Voltage Input Type KSHB XVD 199 99 V 19 999 V 1 9999 V 1 0000 to 5 0000 V e DC Current Input Type KSHB XAD 199 99 mA 19 999 mA 1 9999 mA 4 000 to 20 000 mA AC Voltage Input Type 0 0 to 400 0 V 0 00 to 199 99 V 0 000 to 19 999 V 0 0000 to 1 9999 V AC Current Input Type 0 000 to 10 000 A 0 0000 to 1 9999 A 0 00 to 199 99 mA 0 000 to 19 999 mA E K3HB V Weighing Indicator page 8 Digital Indicators Series Analog Input Series 3 OMRON Process Indicator K3HB X A Process Indicator Ideal for Discriminating and Displaying Measurements for Voltage Current Signals e Easy recognition of judgement results using color display that can be switched between red and green
49. t executed or is cleared Excluding the Turns ON OFF when hold input turns Hold ON OFF MAX MIN Key LEVEL Key Used to switch the Used to switch level display between the PV maximum value and minimum value and to reset the maximum and minimum values PV display Displays PVs maximum values minimum values parameter names and error names Displays the position of the PV with respect to a desired scale SV display Displays SV and monitor values SV display status indicators Turns ON when the timing signal turns TG ON Otherwise OFF Turns ON when parameters for which T teaching can be performed are displayed HH H RUN level turn ON when the comparative set values HH H L and L LL LLare displayed MODE Key SHIFT Key UP Key Used to switch the Used to change When changing a set value parameters displayed parameter settings this key is used to change When changing a set the actual value value this key is used When a measurement value to move along the is displayed this key is digits used to execute or clear the forced zero function or to execute teaching 22 Digital Indicators KBGHB X V H S omn on E BCD Output Timing Chart A REQUEST signal from a Programmable Controller or other external device is required to read BCD data Single Sampling Data Output Continuous Data Output 20 ms pulse min 50 ms max REQ po REQ MAX MIN M
50. termeasures for Inductive Noise on Input Lines Digital Indicator 2 conductors with shield 4 If a noise filter is used for the power supply check the voltage and current and install the noise filter as close to the product as pos sible 5 Reception interference may occur if the product is used close to a radio television or wireless Digital Indicators B X V H S 31 omnon Warranty and Limitations of Liability B WARRANTY OMRON s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year or other period if specified from date of sale by OMRON OMRON MAKES NO WARRANTY OR REPRESENTATION EXPRESS OR IMPLIED REGARDING NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE OMRON DIS CLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED BLIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR COMMER CIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS WHETHER SUCH CLAIM IS BASED ON CONTRACT WARRANTY NEGLI GENCE OR STRICT LIABILITY In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted IN NO EVENT SHALL OMRON BE RESPONSIBLE FO
51. x Max applied voltage 30 VDC max OFF leakage current 1 5 mA max NPN open collector or no voltage contact signal ON residual voltage 2 V max ON current at 0 Q 4 mA max Max applied voltage 30 VDC max OFF leakage current 0 1 mA max 250 VAC 30 VDC 5 A resistive load Mechanical life expectancy 5 000 000 operations Electrical life expectancy 100 000 operations Maximum load voltage 24 VDC Maximum load current 50 mA Leakage current 100 uA max Linear output 0 to 20 mA DC 4 to 20 mA Load 500 max Resolution Approx 10 000 Output error 0 5 FS Linear output 0 to 5 VDC 1 to 5 VDC 0 to 10 VDC Load 5 max Resolution Approx 10 000 Output error 0 596 FS 1 V or less 0 15 V not output for O V or less Negative LCD backlit LED display 7 segment digital display Character height PV 14 2 mm green red SV 4 9 mm green Scaling function 2 input calculation function measurement operation selection averaging previous average value comparison forced zero zero limit output hysteresis output OFF delay output test teaching display value selection display color selection key protection bank selection display refresh period maximum minimum hold reset 10 to 55 C with no icing or condensation 2596 to 8596 25 to 65 C with no icing or condensation DC power supply models require a control power supply capacity of approximately 1 A per Unit when power is turned ON Particular
52. z to 1 GHz Electrical Fast Transient Burst Immunity EN61000 4 4 2 kV power line 1 kV I O signal line Surge Immunit EN61000 4 5 1 kV with line power line 2 with ground power line Conducted Disturbance Immunity EN61000 4 6 3 V 0 15 to 80 MHz Voltage Dips and Interruptions Immunity EN61000 4 11 0 5 cycle 0 180 100 rated voltage 10 Weighing Indicator KSHB V OMRON E Input Ranges Measurement Range and Accuracy Input type Range Set value Measurement range Input impedance Accuracy Allowable instantaneous overload 30 s K3HB VLC As Aud 0 00to 199 99 mV 1 MQ min 20 1 1 200 V Load Cell mV B b ud 0 000to 19 999 mV 0 1 rdg 5 digits max C JE ud 000 J 100 00 mV 0 1 rdg digits max D fd ud 199 99 mV 0 1 1 digit max Note 1 The accuracy is for an ambient temperature of 23 5 For all ranges 10 or less of max input 0 1 FS 2 The letters rdg mean reading a I MEC 1 Connected terminals The area shown in dark shading indicates the factory setting E Load Cell Wiring Example E Scaling Example Using Range A Indicated on the as to 49N in the load cell specifications rated load 49N recommended applied voltage 10 V rated output 2 mV V See note Display value 49 N Scaling values 1 20 mV Note 2 mV V indicates load cell output of 2 mV
Download Pdf Manuals
Related Search