Ilumipod Inground Tri-3 IP Optic 25 RGB User Manual
Contents
1. g e a 316 Stainless Steel Gland Nuts a Tumipod Inground T3 IP Optic 25 RGB User Manual Rev 8 ILUMINARC Product Description Product Dimensions TI Im 7 mm 178 mm 42in 107 mm 6 0 in 153 mm Tumipod inground 17 3 IP 25 RGB User Manual Rav 8 Installation ILUMINARC 3 Installation Always keep the power cables away from the signal cables by running them in diferent conduits and using separate distribution boxes lumipod Inground T3 IP Optic 25 RGB products ean support distributed load of up lo 3 000 kg 6 614 Ib when properly installed Installation Notes The llumipod Inground Tri 3 IP Optic 25 RGB consists of two parts the product housing and the concrete installation sleeve The product housing is IP67 rated The installation sleeve is not Read the Installation Sleeve Setup instructions carefully Installation Sleeve Orientation You will have to run the AC power and signal cables into the concrete installation sleeve Position the installation sleeve so the signal cable enters the sleeve using one of the two cable inlets Use the opposite inlet for the power cable refer to the following figure This will reduce the stress to the signal and power cables when setting down the product while keeping them2. Tumipod Inground T3 IP Optic 25 RGB User Manual Rev ILUMINARC Technical Information LED Disclaimer LED Life ILUMINARC rates LED lifetime based on lumen depreciation of 70 of the original Output with data provided by the manufacturer of the LED Data from the manufacturer of the LED are not independently verified or measured by ILUMINARC When the product is operating in optimal environmental conditions the LED lifetime is rated to be 50 000 to 70 000 hours by the LED manufacturer LED Binning LED manufacturers sort LEDs into bins based on variances in color output intensity and the frequency at which the semiconductor operates ILUMINARC strives to hold its LED manufacturers to the highest standards of binning to optimize consistency in output from product to product However the availability of a single bin cannot be guaranteed With that in mind ILUMINARC has developed a rigorous control system to seek the best achievable consistency in color and output Color Rendering Index CRI CRI is an industry standard method to compare properties of different types of light sources There are known limitations and inconsistencies related to CRI Results may vary depending on the environmental factors involved For this reason the US Department of Energy DOE states that CRI should be considered as one point of reference among others in evaluating white LED products and systems The following is an excerpt of r
3. ol them that do not correspond with this menu map Skip them as they do not work with the RGB only output products DMX Personality Go to PERSON and select any DMX personality llumipod Inground Tri 3 IP Optic 25 RGB ARCI ARCI D ARC FULL SOLID 2 Make sure to rearrange the DMX addresses of all fixtures in the current DMX universe to avoid address overlapping DMX Starting Address 1 Goto DMX 2 Select starting DMX address 001 512 Tumipod inground IP Opli 25 RGB User Manual Rev Operation ILUMINARG Static Colors 1 Goto STATIC 2 Selecta color RED GREN green or BLUE or the strobe effect STRB 3 Select a color value 000 235 0 100 or a strobe frequency 0 20 0 20 Hz Whites Setting L Goto CALIB 2 Selecta white color WHITE 1 11 or RGBTOW 3 Select an RGB color RED GREN green or BLUE 4 Selecta color value 0 255 0 100 5 Repeat steps 3 and 4 for the other RGB colors to obtain a white color 6 Repeat steps 2 to 5 for the other white colors Color 1 Goto SETTINGS gt COLOR 2 Select the color method OFF RGBTOW or UC Color Descri n or Nene ROB ads st 288 he output When the RGB faders are all at 288 the output is the selected RGBTOW white color see Whites Setting Uc When the RGB faders are all at 255 the output matches the same color output of previous versions of this product Dimmer Dit is tno dimer This setting gives
4. Chauvet Mexico Address Av Santa Ana 30 Parque Industrial Lerma Lerma Mexico 52000 Voice 52 728 285 5000 Technical Support Voice 800 762 1084 Email su iluminarc com World Wide Web www iluminarc com Technical Support Email Eutech chauvetlighting eu World Wide Web www chauvetlighting eu Technical Support Email uktechGiluminarc com World Wide Web www chauvetlighting co uk Technical Support Email servicio iluminarc com mx World Wide Web www chauvet com mx Outside the U S United Kingdom Ireland Mexico or Benelux contact the dealer of record Follow their instructions to request support or to return a product Visit our website for contact details Tumipod Inground T73 IP Optic 25 RGB User Manual Rev ILUMINARC Technical Information Technical Specifications Dimensions and Diameter Width Height Weight Weight 6 0 in 153 mm 6 0 in 153 mm 70 in 178 mm 4 6 lb 2 0 kg Note Dimensions in inches rounded to the nearest decimal digit Electrical ESTES EE VEE Switching intemal 100 t0 240 VAC 50 60 Hz Autoranging TT 220 V sonz 122w nw 02A oia Fisco n EE CS Open Wire NA Cond plus NA NA Light Source T EET LED 50 000 hours color auanaty ERR Tricolor RGB 3 1050 mA Photometric CAREA 5m Em uM 18 Field angle Thermal LEELA CSOT SS memes Convection nux Open Wire Hardw
5. The user must send the merchandise prepaid in the original box and with its original packing and accessories ILUMINARC will not issue call tags Call ILUMINARC and request a Return Merchandise Authorization Number RMA before shipping the product Be prepared to provide the model number serial number and a brief description ofthe cause forthe return The user must clearly label the package with a Return Merchandise Authorization Number RMA ILUMINARC will refuse any product returned without an RMA Once you receive the RMA please include the following information on a piece of paper inside the box Your name Your address Your phone number The RMA A brief description of the problem Be sure to pack the product properly Any shipping damage resulting from inadequate packaging will be the customer s responsibility As a suggestion proper FedEx packing or double boxing is the shipping method ILUMINARC recommends USA WORLD HEADQUARTERS Contact General Information ILUMINARC Address 5200 NW 108th Avenue Sunrise FL 33351 Voice 954 923 3680 Fax 800 544 4898 EUROPE General Information Chauvet Europe BVBA Address Stokstraat 18 9770 Kruishoutem Belgium Voice 329 388 93 97 General Information Chauvet Europe Ltd Address Unit 1 Brookhill Road Industrial Estate Pinxton Nottingham UK NG16 6NT Voice 44 0 1773 511115 Fax 44 0 1773511110 MEXICO General Information
6. or dry compressed ait and a soft brush to remove dust collected on the external surfaces Clean all external glass optics and glass surfaces with a mild solution of glass cleaner or isopropyl alcohol and a soft lint free cotton cloth or a lens cleaning tissue Apply the solution directly to the cloth or tissue and drag any dirt and grime to the outside of the lens Gently polish the external glass surfaces until they are free of haze and lint Product Repairs ILUMINARC strongly advises you against attempting any repairs to this product unless you are an authorized ILUMINARC technician ILUMINARC presents the information contained in the Troubleshooting Table as a guide only In most cases opening the product s housing will invalidate its warranty unless there is a written indication to the contrary 16 Tumipod Inground T3 IP Optic 25 RGB User Manual Rev ILUMINARC Technical Information Troubleshooting Guide Symptom Cause s Action s Product does not light up Dimmer fader set to 0 Increase the value of the dimmer channel All color faders set to 0 Increase the value of the color channels All colors in STATIC arc set to 0 Increase the values of the colors Unit is being configured with lumicode Complete the configuration process No power Verily external power circuit and wiring Faulty internal power supply Return for service to ILUMINARC Faulty
7. 9 8000 K White 10 8500 K White 11 10000 K Green Up Green 100 Green 100 Green Down Green 0 Green 0 Green Up Green Down Green 100 Blue 0 Blue 0 Blue Up Blue 100 Blue 100 Blue Down Blue Up Blue 100 Blue 100 7 Strobe 00007 loos 004 255 Function lo 20 Hz 8 Dimming Speed 0 10100 0 0700 1300 1900 009 029 069 129 189 255 Dimmer is set by Humicode OFF dimmer is linear DIMI fastest dimmer curve IDIM3 IDIM4 slowest dimmer curve Tumipod inground IP Optic 25 RGB User Manual Rev amp Technical Information ILUMINARG 5 Technical Information Always dry the external optics and glass surfaces carefully ater cleaning tham I you sil experience technical problems alter trying the solutions in the Troubleshooting Table contact ILUMINAROS Technical Support Product Maintenance To maintain optimum performance and minimize wear the user should clean the products frequently Usage and environment are contributing factors in determining the cleaning frequency As a rule the user should clean the products at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced light source life To clean a product follow the instructions below Disconnect the power to the product Wait until the product is at room temperature Use a vacuum
8. Optic 25 RGB User Manual Rev ILUMINARC Operation 4 Operation Addresser The llumipod Inground Tri 3 IP Optic RGB needs an external controller the Ilumicode addresser to change its configuration llumicode Panel Description Button Function lt MENU gt Exits from the current menu or function lt ENTER gt Enables the currently displayed menu or sets the Currently selected value into the selected function lt UP gt INavigates upwards through the menu list and increases ihe numeric value when in a function DOWN INavigates downwards through the menu list and decreases the numeric value when in a function POWER Turns the unit on The will turn off automatically latter 30 seconds of inactivity Control Options You can set the Ilumipod Inground Tri 3 IP Optic 25 RGB start address in the 001 512 DMX range This allows for the control of up to 73 fixtures in the 7 channel ARC FULL personality Programming Carry out all the programming procedures indicated below from the control panel Refer to the Menu Map to learn how the menu options relate to each other Use ENTER and lt MENU gt to change levels in the Menu Map This is equivalent to moving right and left respectively Use lt UP gt and lt DOWN gt to move vertically within the Menu Map options When you scroll through the i A menu options you will see
9. This icon indicates useful although non information This icon indicates important instalation or configuration information Failure to comply with this information may prevent the product from functioning correctly This eon AN cca or oparon rorhton Eure to compy wh ts render the produc parialy or Sonploy damage uri ary saxon or causo harm res The term DMX used throughout this document refers to the USITT DMX512 A transmission protocol What Is in the Box One Ilumipod Inground Tri 3 IP Optic 25 RGB One Installation Sleeve Warranty Card Quick Reference Guide Unpacking Instructions Immediately upon receiving a product from ILUMINARC carefully unpack the carton Check the contents of the box to ensure that all parts are present and that they are in good condition Claims The carrier is responsible for any damage incurred during shipping Therefore if the received merchandise appears to have been damaged during shipping the customer must submit the damage report and any related claims to the carrer not ILUMINARC The customer must submit the report upon reception of the damaged merchandise Failure to do so in a timely manner may invalidate the customer s claim with the carrier For other issues such as missing components or parts damage not related to shipping or concealed damage the customer must make claims to ILUMIN
10. any other purpose without its written consent Document Printing For better results print this document in color on letter size paper 8 5 x 11 inches double sided If using A4 paper 210 x 297 mm configure your printer to scale the content of this document to A4 paper Intended Audience person in charge of installing operating and or maintaining the Ilumipod Inground Tri 3 IP Optic 25 RGB should read the Quick Reference Guide that shipped with product and this manual in their entirety before installing operating or maintaining this product Disclaimer ILUMINARC believes that the information contained in this manual is accurate in all respects However ILUMINARC assumes no responsibility for any error or omissions in this document ILUMINARC reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of ILUMINARC to notify any person or company of such revision or changes This does not constitute in any way a commitment by ILUMINARC to make such changes ILUMINARC may issue a revision of this manual or new edition of it to incorporate such changes Document Revision The Humipod Inground Tri 3 IP Optic 25 RGB User Manual Rev 8 supersedes all previous versions of this manual Please discard any older versions of this manual you may have whether printed or electronic format and replace them with this version I 0 Date ER NNNM Dem
11. separated under the product s housing mir Signal m ES ull Power cable box Installation Sleeve Setup When setting up the installation sleeve make sure that any water that may have entered it can drain out of the sleeve on its own Locate the installation sleeve above the normal drainage level so the product is never under more than 1 m of water IP67 during heavy rain In addition make sure that the installation sleeve and the stainless steel collar are horizontal and even with the ground surface This helps to distribute the load uniformly over the product s surface and avoids creating dangerous bumps Collar 7 Drainpipe Hardpan Nesey Tumipod Inground T3 IP Optic 25 RGB User Manual Rev ILUMINARC Installation Always connect lumipod Inground Tri 8 IP Optic 25 RGB to a protected circuit with an appropriate electrical round to avoid the risk of electrocution or fre Never connect llumipod Inground Tri 3 IP Optic 25 RGB 1o a rheostat variable resistor or dimmer circut even if the rheostat or dimmer channel serves only as a Oto 100 such Make sure to AX connestine Tripod Inground Tia IP 25 RGB toa power tne wih the proper Taage and frequency as perth spaccalons in ths marai or on the product s skr The listed curent rating indicates tre maximum current draw
12. the user four different options to simulate the dimming curve of an curve and DIMA incandescent lighting product isthe slowest 1 Goto DIMMER 2 Select a dimmer curve OFF or DIMI 4 Procedur DIMMER Description OFF Dimmer curve is linear with fader DMI Non linear fastest DIM2 Non linear fast DIM3 Non linear slow DIM4 Non linear slowest Reset This option resets the Ilumipod Inground Tri 3 IP Optic 25 RGB to the factory default settings 1 Goto SETTINGS gt RESET 2 Select YES or NO 12 Tumipod Inground T3 IP Optic 25 RGB User Manual Rev 8 ILUMINARC Operation Menu Map Main Level Programming Levels Description Dux wis Sets the DMX starting address ARCH RGB coil RET channel RGB conti dimmer PERSON control immer color macro s eam T channel RGB control di 7 dimmer spe SOLID hanc dimmer W mELH Determines the white balance for the color macros carm GREN 0 255 Roprow BLUE crn wc aa RGBTOW i om Dimmer works in incar mode Din DIMMER DIME immer works in non linear mode fom fast DIMI E DIM DIM s 0255 Configures the siatie color 0 1008 and siari strobe eet 0 20 H2 Vas OFF Maximum ouput unbalanced white coLon RGBTOW _ Vic ouput is as per CALIB gt RGBTOW sening SETTINGS UC matcher da of product s previous version
13. ARC within seven 7 days of receiving the merchandise Text Conventions Convention Meaning 1512 A range of values in the text 5060 set of mutually exclusive values in the text DMX Primer The name of another publication or manual lt SETS A button on the product s control panel Settings A product function or a menu option MENU gt Settings A sequence of menu options 1 10 A range of menu values from which to choose in a menu Yes No A set of two mutually exclusive menu options in a menu ON A unique value to enter or select in a menu Tumipod inground IP Optic 25 RGB User Manual Rev 8 T Introduction ILUMINARC There no user serviceable parts inside tns product Any reference to Servicing you may find from now on in this User Manual wll only apply o properly certiied ILUMINARC technicians Do not open the housing or attempt any repairs unless you certified do 0 Please refer to all applicable local codes and regulations for the proper installation ofthis product B Keep this manual for future consultation If you sell this product to another user make sure that they also receive this manual Inthe unholy event that your umipod Inground Tri 3 IP Optic 25 RGB may require service please contact ILUMINARCS Technical Support Safety Notes Please read all the followi how to install use and maintain this p
14. Ilumipod Inground Tri 3 IP Optic 25 RGB User Manual ILUMINARC Edition Notes ILUMINARC Edition Notes The Ilumipod Inground Tri 3 IP Optic 25 RGB User Manual Rev 8 covers the description safety precautions installation programming operation and maintenance of the Humipod Inground Tri 3 IP Optic 25 RGB ILUMINARC released this edition of the Ilumipod Inground Tri 3 IP Optic 25 RGB User Manual Rev 8 in November 2015 Trademarks The ILUMINARC logo the ILUMINARC name and all other trademarks in this document related to services or products by ILUMINARC are trademarks owned or licensed by ILUMINARC its affiliates or subsidiaries Any other product names logos brands company names trademarks featured or referred to within this document are the property of their respective trademark holders Copyright Notice The entire content of this document except where applicable and unless otherwise noted is solely owned by ILUMINARC a wholly owned trademark of Chauvet amp Sons Inc Copyright 2015 ILUMINARC All rights reserved Electronically published by ILUMINARC in the United States of America Manual Usage ILUMINARC authorizes its customers to download and print this manual for professional information purposes only ILUMINARC expressly prohibits the usage copy storage distribution modification or printing of this manual or its content for
15. during normal operation It you choose to bury the power or signal distribution boxes make sure that they are IP67 rated or greater AC Power The Humipod Inground Tri 3 IP Optic 25 RGB has an auto ranging power supply that can work with an input voltage range of 100 240 VAC 50 60 Hz Make sure that you are connecting this product to the proper voltage as per the specifications in this User Manual or on the product s sticker Power Consumption To determine the power requirements for the Humipod Inground Tri 3 IP Optic 25 RGB see the label affixed to the side of the product Alternatively you may refer to the specifications chart in the Technical Information chapter of this User Manual The listed current rating indicates the maximum current draw during normal operation AC Plug The Ilumipod Inground Tri 3 IP Optic 25 RGB comes with an un terminated power input cord for hardwiring during installation Use the table and the illustration below to wire a plug Connection Wire US Screw Color US Wire Europe IP67 Pin AC Live Black Yellow or Brass Brown 1 AC Neutral White Silver or Gray Blue 2 Ground Green Yellow Green GreenYellow 3 Power Wiring You can connect the bare ended IP67 rated AC power cable from the fixture to an 1 67 rated power connector or IP67 rated junction box If using junction boxes make sure to use IP 7 rated conduit for surface installations F
16. e suis Tumipod Inground T 3 IP Optic 25 RGB User Manual Rev 8 ILUMINARG Table of Contents Table of Contents 1 Introduction What Is in the Box Unpacking Instructions Claims Text Conventions Safety Notes Personal Safety Mounting and Installation Power and Wiring Operation 2 Product Description Features Additional Equipment Product Overview Product Dimensions 3 Installation Installation Notes Installation Sleeve Orientation Installation Sleeve Setup bobo ikon mabo W KRENN H a AC Power Power Consumption AC Plug Power Wiring DMX Linking DMX Modes Protocol Connectivity Controllers DMX Controller llumicode Addresser 10 4 Operation llumicode Addresser llumicode Panel Description 11 Control Options Programming DMX Personality 11 DMX Starting Address 11 Static Colors 12 Whites Setting 12 Color 12 Dimmer 12 Reset 12 Menu Map 13 DMX Values 14 ARC 1 14 ARC 1 D 14 SOLID 14 ARC FULL 15 Tumipod Inground IP Optic 25 RGB User Manual Rev 8 i Table of Contents ILUMINARG 5 Technical Information 16 Product Maintenance 16 Product Repairs 16 Troubleshooting Guide 17 Photometrics 18 LED Disclaimer 19 LED Life 19 LED Binning 19 Color Rendering Index ORI 19 Returns Procedure 20 Technical Specifications 21 Ilumipod Inground Tri 3 IP Optic 25 RGB User Manual Rev 8 ILUMINARC Introduction 1 Introduction
17. ecommendations from the DOE 1 Identify the visual tasks to be performed under the light source If color fidelity under different light sources is critically important for example in a space where color or fabric comparisons are made under both daylight and electric lighting CRI values may be a useful metric for rating LED products 2 CRI may be compared only for light sources of equal CCT This applies to all light sources not only to LEDs Also differences in CRI values of less than five points are not significant e g light sources with 80 and CRI are essentially the 3 If color appearance is more important than color fidelity do not exclude white light LEDs solely on the basis of relatively low CRI values Some LED products with CRIs as low as 25 still produce visually pleasing white light 4 Evaluate LED systems in person and if possible on site when color fidelity color appearance are important issues Source DOE publication PNNL SA 56891 January 2008 Tumipod inground IP Optic 25 RGB User Manual Rev amp 15 Technical Information ILUMINARC DO NOT write f the RMA directly on the Instead write it on a properly affixed label 2 right to use ts own discretion to repair replace returned products Af orginal box and all packaging material as you wil need hose to ship the product back to ILUMINARO JLUMINARCR reserves the Always keep the Returns Procedure
18. gnments will depend on the chosen personality see the Menu Map and the DMX address assigned to each product see Programming The figure below illustrates how to connect the DMX controller to the lumipod Inground Tri 3 IP Optic 25 RGB products Mu Mu Power DMXST2 A Controller Tumipod inground IP Optic 25 RGB User Manual Rev Installation ILUMINARC The RDM2go which includes buit in lumicodo adresser along with many other useful features is available ILUMINARC suggests that you connect no more han 20 products together at one time with ths controller and keep the otal distance to less than 60 m 197 11 Otherwise You might need to use an optically isolated signal amplifier Ilumicode Addresser The Humicode addresser Iumicode is required to program the settings on the Ilumipod Inground Tri 3 IP Optic 25 RGB The diagram below shows how to connect the Dlumicode addresser to this product Note that this connection will control multiple products at the same time all having the same DMX address The Tumicode must be used to configure the product The Humicode can be purchased separately through your ILUMINARC sales representative 677 Mu 1 To Power other e 6 1 Gnd Blackdipl 2 08 2 Data Green clip Date 3 Data Red dip DMX Output Signal Connector Ilumicode Addresser T0 Tumipod Inground T3 IP
19. ired een Ordering MimipodingoundTikS pecu 11003001 RoHS ur 1573 cshc222No 166 c US 113093 Tumipod inground IP Optic 25 RGB User Manual Rev 8 ILUMINARC ILUMINARC
20. main control board Return for service to ILUMINARC LED does not work Faulty LED Faulty LED module Faulty LED driver Return for service to ILUMINARC The wrong LEDs light up when using DMX Wrong personality Change the personality Wrong DMX address Change the DMX address Circuit breaker fuse keeps tripping blowing Excessive circuit load Check total load placed on the electrical circuit Short circuit along the power wires Check fora short in the electrical wiring Product does not power up No power Check for power on power outlet Loose or damaged power cord Check power cord Faulty internal power supply Return for service to ILUMINARC Product does not respond to DMX Wrong DMX addressing Check Control Panel and product addressing Damaged DMX cables Check DMX cables Wrong polarity on the controller Check polarity switch settings on the controller Loose DMX cables Check cable connections Faulty DMX interface Return for service to ILUMINARC Faulty Display Main board Return for service to ILUMINARC DMX signal problems Non DMX cables Use only DMX compatible cables Bouncing signals Install terminator as suggested in the DMX Primer from the ILUMINARC website at hitp seww iluminarc com reports dmx primer Long cable low level signal Install an optically coupled DMX
21. od Inground T3 IP Optic 25 RGB User Manual Rev 8 ILUMINARC Product Description 2 Product Description The Ilumipod Inground Tri 3 IP Optic 25 RGB is a tri color wash light intended for inground installation The product consists of a cast aluminum body containing power supply control unit drive over rated glass lens cover and tri color LEDs Features 1 3 4 or 7 channel DMX 512 LED inground washlight Operating modes 1 channel SOLID Dimmer 3 channel ARC 1 RGB control 4 channel ARC 1 0 RGB dimmer 7 channel ARC FULL RGB dimmer color macro strobe dimmer speed Five distinct dimming curves 1 67 stainless steel gland nuts for cable entry Remotely addressable with Humicode Addresser IP67 ingress protection Gore valve Drive over rated glass lens cover High power 3 W 1 050 mA tri color LEDs Additional Equipment Iumicode addresser required for product configuration sold separately The RDM2go which includes a builtin ilumicode addresser along with many other useful features is now available The Ilumicoode addresser is required for product configuration sold separately Tumipod inground IP Optic 25 RGB User Manual Rev amp 3 Product Description LU NARC Product Overview LI Installation I Sleeve gt 9 S BO CN I
22. roduct safely 1g safety notes carefully because they include important information Personal Safety Avoid direct eye exposure to the light source while the product is on Always disconnect this product from its power source before servicing Always connect this product to a grounded circuit to avoid the risk of electrocution Do not touch this product s housing when operating because it may be very hot Mounting and Installation This product is for outdoor use and can be submerged IP67 However do not submerge deeper than 1 m for more than thirty 30 minutes CAUTION When transferring product from extreme temperature environments e g cold truck to warm humid ballroom condensation may form on the internal electronics of the product To avoid causing a failure allow product to fully acclimate to the surrounding environment before connecting it to power Make sure there are no flammable materials close to this product while operating Power and Wiring Always make sure that you are connecting this product to the proper voltage as per the specifications in this manual or on the product s sticker Make sure that the power input cable is not cracked crimped or damaged Rois ene att cats IEE E Operation The maximum ambient temperature is 113 F 45 C Do not operate this product at a higher temperature In case of a serious operating problem stop using this product immediately Tumip
23. rom To fuse other panel i boxes Conduit Distribution Box Tumipod inground IP Opli 25 RGB User Manual Rev 7 ILUMINARC Installation The llumipod Inground Tri 3 IP FEE EIE G limiting the total length of the DMX cable from the first to the us fast product 10 300 455 m 985 1 500 0 Disconnect the product trom the power before opening it Tho signal cable must match or exceed the electrical characteristics of ihe Belden 9841 cable for EIA RS 485 applications You may also use CATS Se or DMX Linking You may link the Ilumipod Inground Tri 3 IP Optic 25 RGB to a DMX controller using standard DMX serial connection If using other DMX products compatible with the Humipod Inground Tri 3 IP Optic 25 RGB you can control each individually with a single DMX controller If you are not familiar with the DMX standard or if you need information about the DMX cables needed to link the Ilumipod Inground Tri 3 IP Optic 25 RGB to a DMX controller you may download the DMX Primer document from the ILUMINARC website at bitp www iluminarc com reports dmx primer DMX Modes The Humipod Inground Tri 3 IP Optic 25 RGB uses the standard DMX data connection for its ARC 1 ARC 1 D ARC FULL and SOLID Refer to the Introduction chapter for a brief description of these modes and the Operation chapter to learn ho
24. s YES RESET Resets producto facto default stings NO Tumipod inground 1P Optic 25 RGB User Manual Rev 6 E ILUMINARG Operation DMX Values ARC 1 Channel Function Value _ PercentiSetting 1 Red 00000 255 0 100 2 Green poo U_255 o 100 3 Blue 000 U 255 0 100 ARC 1 D Channel Function Value PercentiSetting 1 Dimmer 00000 255 0 100 2 Red 0_255 0 100 3 Green 00000 255 o 100 4 Blue U 255 0 100 SOLID Channel Function Value _ PercentiSetting 1 Dimmer 0 255 0 100 Tumipod Inground Tri 31P Optic 25 RGB User Manual Rev 8 ILUMINARC Operation ARC FULL Channel Function Value Percent Setting Dimmer 000 0 255 10 10092 Red 0 255 100 Green 0 255 10 10092 00007 255 10 1009 e e White 0 255 10 1009 6 Color Macro White Balance 000707 jori 10310 0510 0710 10910 110 1310 1510 1710 201 0 206 0 2110 2160 2210 226 0 230 236 0 241 246 251 010 030 050 070 090 110 130 150 170 200 205 210 215 220 225 230 235 240 245 250 255 INo Function Rea 100 Red Down Red 0 Red 0 Red Up Red 100 Red 100 Red Down 100 White 1 3200 K White 2 3400 K White 3 4200 K White 4 4900 K White 5 5600 K White 6 5900 K White 7 6500 K White 8 7200 K White
25. splitter right after the product with the strong signal many products Install an optically coupled DMX splitter after product 32 or before Interference from AC wires Keep DMX cables separated from power cables or fluorescent black lights Tumipod inground IP Optic 25 RGB User Manual Rev Technical Information ILUMINARC Photometrics Filename lumipod Inground Tri IP Optic 25 RGB Polar Candela Distribution 100 diii 180170 1609 180 140 Manufacturer ILUMINARC Luminaire lumipod Inground Tri 3 IP Optic 25 RGB 1500 2e Lamp 3 Tricolor aate Lamp Output 1 lamp rated Lumens lamp 1380 ume Max Candela 1 749 7 at Horizontal 0 Vertical 3 sw Input Wattage 12 2 E Luminous Point hs Opening Test 2010 07 26 co Test Lab ILUMINARCB amp D Optics Laboratory I Photometry Typo 1 ae CIE Class Direct 4 m Cutoff Class Full Cutoff a or 120 159 E 190 VAO i 20 4e Food Summary cen Lumens Noon Spread Vera Spread Felis Beam SO zux ns at a Distance Center Beam FC Beam Width am 19040 iot a 47 60 fc ist a 21 16 fe 2 2st el 11 90 fe ial 762 fe ast ast p 5 29 fe sat Vert Spread 184 MiHoriz Spread 175 Photometics Pro 1 3 2 copyright 2003 2008 by jSolutions Inc Reported data calculated from manufacturer s data file based on IES recommended methods
26. w to configure the Ilumipod Inground Tri 3 IP Optic 25 RGB The DMX Values section will give you detailed information regarding the above mentioned DMX modes DMX Mode DMX Address DMX Mode DMX Address SARC FULL 506 SOLID 512 510 ARC T D 509 Protocol Connectivity The Ilumipod Inground Tri 3 IP Optic 25 RGB uses the USITT DMX 512 Protocol The procedure below illustrates the recommended connection method CATE LAN cabe Shield xj 2 Data In Black 3 Data In White data Out Green ata Red 4 f a f 1 Z t Signal Junction Junction Sona h box Conduit box out D Tumipod Inground 25 RGB User Manual Ra 8 ILUMINARC Installation It you have not configured the DMX staring address and DMX modo for each product hoy wil all use their default values This means that all products wil operate In unison Controllers The llumipod Inground Tri 3 IP Optic 25 RGB can operate with a standard DMX controller the Humicode addresser The sections below will show you how to connect these products to the corresponding controllers The instructions to operate these products with each of the above controllers are in the Operation chapter of this User Manual DMX Controller The Humipod Inground Tri 3 IP Optic 25 RGB products can work with a standard DMX controller The channel assi
Download Pdf Manuals
Related Search