Home

installation

image

Contents

1. e Insert the blocking handle in the top part the smooth part outwards the crowned part inwards Fig 8 e Push the bar downwards lining up the holes of the handle with those of the pin and slide in the locking pin leaving the knurled outward Fig 9 Use a hammer to push the pin in the holes bringing it up to the plastic handle Fig 10 STRONG trim PRO OPTIONAL SHEET HOLDER BAR e Follow the same operation on the opposite side Feeding the media to cut B 2 Follow the procedure of the manual in paragraph 5 1 2 to trim the media with the sheet holder bar After inserting the media to trim block it with the sheet holder bar rotating the two side handles of the bar downwards After cutting unlock the sheet holder rotating the side handles upwards and remove the trimmed part STRONG trim PRO OPTIONAL SHEET HOLDER BAR STRONG trim PRO B 4 OPTIONAL CUTTING AREA LAMP Assembly of the lamp optional C 1 To assemble the lamp in the cutting area follow this procedure Remove the lamp from the box and the bag with the supplied SCrews e Remove lamp from lamp holders Fig 1 e Assemble the glass ceiling bowl to the table fastening the brackets already on the lamp to the threading bushes on the upper traverse on the back part of the table Fig 2 3 STRONG trim PRO OPTIONAL CUTTING AREA LAMP e Slide lamp out of protection carton and insert
2. 4 4 1 Qualification of the 4 1 VE 00 RR 4 1 4 2 1 Transport Conditions 4 1 4 2 2 Assessment of damages during transportation 4 2 I FNS TOMEI ari 4 3 4 4 AQJUSINENL 4 6 01100 4 7 ddl CGAIACIOT SU CS 4 7 ZO LOCA sense 4 4 6 1 Characteristics Of the location 4 7 4 6 2 TESting iii 4 8 STRONG trim PRO CONTENTS Chapter BMS iii 5 5 1 Qualification of the 5 1 5 1 1 WOKING PIACE ater 5 1 5 1 2 Insertion of the media to be CUL i 5 1 5 1 3 Characteristics of the media to be 5 2 Chapter Maintenance scsssssccecesesessesececeesescseseseseescecsesesessvacseseseeavaeecsesesesaeaeees 6 6 1 Routine 6 1 6 1 1 Qualification of the operator 6 1 OTa FO OUTO 6 1 6 2 Extraordinary maintenance iii 6 1 Chapter 7 Demolition cccececssssesesecscsesecececesesesesscscsesece
3. USER MANUAL STRONG trim pro 1130 1800 230 GB USER S MANUAL N Cod NLT QR C N MM 2 1S GB NEOLT ENGLISH USOGB STR_pro DOC 2002 CONTENTS Q SECTOR STRONG TRIM PRO Q DATE 19 03 2002 Q VERSION STR_PRO 01 Q AUTHOR POLENI P 13 Property of INfOrMatiON ui 1 1 1 4 CONV CNHONS nia 1 2 1 4 1 Conventional 1 iii 1 2 1 4 2 Conventional symbols used iii 1 2 1 5 Identification data of the manufacturer nenne nennen 1 3 1 6 Identification data of the machine iii 1 3 VANE E EE 1 4 DEVICE 1 4 1 9 Use of this MANUAL iii 1 4 1 10 Description of the machine 1 5 AOC 1 5 MZ iaia 1 5 1 10 SUI 1 6 2 Salely INIOrMallON anna een 2 54 er re 2 1 2 2 Qualification of the 2 2 FCC 2 2 2 4 Dangerous areas and residual rISKS 2 3 Chapter Characteristics of the machine ii iii 3 3 1 Technical specifications ie 3 1 3 2 Power 3 1 Ja EIST OF IE een 3 2 Chapter A Installation e
4. This manual cannot be reproduced or copied as a whole or in parts without prior written consent of NEOLT S p A These documents are provided only for the use of the client whom the manual has been supplied to with the machine and can be used only for the installation use and maintenance of the machine the manual refers to NE S p A states that the information of this manual complies with the technical and safety requirements of the machine the manual refers to The manufacturer cannot be held responsible for any direct or indirect damages to people objects or pets due to the use of these documents or of the machine in conditions other than those authorized NE OLT S p A reserves the right to change or improve without prior notice this manual users manual and the machines and also other machines marketed of the same model as the one this manual refers to but with a different serial number The information of this manual particularly refers to the machine specified in 1 6 Identification data of the machine STRONG trim PRO GENERAL INFORMATION Conventions 1 4 Conventional terms 1 4 1 Machine indicates the machine specified in section 1 6 Identification data of the machine Frame structure supporting the machine Qualified personnel people who thanks to their qualification preparation and experience and thanks to the knowledge of the relevant rules safety requirements and service norms are able to recognize and a
5. ea lee WITH STAND WW OUT STAND STRONG trim PRO 1 3 GENERAL INFORMATION Warranty 1 7 NEOLT S p A warranty covers the machine for one year The parts subject to normal wear and tear are not included in the warranty The warranty is limited to the substitution or repair of the parts that should result damaged or defected The assessment of the defects and causes is carried out at NE OLT S p A facilities The warranty is cancelled if the machine is used incorrectly or in an improper or excessive way If any non original spare parts are used and for noncompliance with the norms of this manual In no case can the purchaser demand the resolution of the contract claim for damages or the extension of the warranty S p A cannot be held responsible for any negative advertisement or loss of earnings due to technical or mechanical malfunctioning of the product in use or in display Service 1 8 NEOLT S p A provides on request assistance for the installation and the maintenance of the machine Use of this manual 1 9 Carefully read the chapters General information Safety information Characteristics of the machine and Operator interface Please consult the relative chapter for any transportation installation use maintenance and demolition operation This manual and the attached documentation must be kept for the entire technical life of the machine in order to consult it quickly when necess
6. to the stand easier e The trimmer is now ready to start operating As the machine is factory tested no further adaptation is required STRONG trim PRO 4 5 INSTALLATION The trimmer should not need any specific adjustments but we do suggest to check the two options that could be slightly different due to the final positioning of the trimmer Planarity The first adjustment is the planarity of the working table which could vary due to unleveled floors Follow this procedure to adjust the planarity of the feeding table e Position the profile of rigid material on the trimmer s table with a well trimmed side e Check the parallelism between the table and the profile of the rigid material by using the push rod in the center of the traverse on the upper table 13 Screw on to lower table unscrew to lift table e Furthermore adjust the two supports placed under the table 14 by putting the screws on or off After reaching the desired adjustment block the screw with the two locking nuts Sheet holder adjustment The second operation is the adjustment of the height of the Plexiglas sheet holder when the carriage is at the far right or left to remove the trimmed media Follow this procedure e Put the setscrew wrench in the hole of the transparent sheet holder lifter slide 15 and screw on to decrease height unscrew to increase height STRONG trim PRO INSTALLATION The instructions contained in thi
7. Attachment 1 Attachment 2 Attachment 3 Attachment 4 Attachment 5 Assembly optional reel holder Assembly optional sheet holder bar Assembly optional cutting area lamp Technical sheet replacement of rotating blade Part list and drawing STRONG trim PRO ATTACHMENTS STRONG trim PRO 8 2 OPTIONAL REEL HOLDER Assembly ofoptionalrollholder AT Follow this procedure to assemble the reel holder e Insert the reel holder supports in the right and left legs l and screw on the proper screw in the back part of the stand e Insert the reel holder in the seats of the stand that you just assembled 2 STRONG trim PRO A 1 OPTIONAL REEL HOLDER STRONG trim PRO A 2 OPTIONAL SHEET HOLDER BAR Follow this procedure to assemble the optional sheet holder bar e Remove the components of the sheet holder from the box The assembly components Fig 1 and the bar Fig 2 e Slide in the screw in the shoulder of the trimmer from the bottom Fig 3 Screw on the pin so that the holes for the plug are parallel with the shoulder of the machine Fig 4 and tighten the screws with the supplied setscrew wrench Remove the screws that fix the top part of the brackets Fig 5 and replace with the shorter profile you find in the box STRONG trim PRO B 1 OPTIONAL SHEET HOLDER BAR Slide in the spring of the sheet holder Fig 6 and the sheet holder bar Fig 7
8. ages to people pets or objects due to noncompliance with the safety rules and the recommendations contained in the supplied documentation STRONG trim PRO INFORMATION ON SAFETY Personnel qualification 2 2 Stage of the technical life of the machine Qualification of the operator in charge Transport Qualified transportation Installation Qualified personnel Use Qualified personnel Routine maintenance Qualified personnel Extraordinary maintenance Engineers authorized by NE OLT S p A Demolition Qualified personnel Protections 2 3 S p A cannot be held responsible for any damages to people pets or objects due to noncompliance with the safety rules and the recommendations contained in the supplied documentation Tampering with the protections and the safety devices is dangerous for the people using the machine and for those exposed to it NEOLT S p A cannot be held responsible for any damages to people animals or objects due to tampering with the protections STRONG trim PRO INFORMATION ON SAFETY Any area closed to the machine where a person is exposed to injuries or health risk is to be considered dangerous Fig 2 1 Cutting area Pay particular attention to your hands during cutting operations During some procedure on this machine as specifically indicated in this manual there could be residual risks for the operator Residual risks can be pre
9. ary If the machine is sold as second hand this manual and the attached documentation must be supplied along with the product STRONG trim PRO 1 4 GENERAL INFORMATION Description of the machine 1 10 Correct use of the machine 1 10 1 This machine can be used only to cut media having the allowed basic weight max paper thickness 4 5 mm As the machine consists of assemblies physically separated and autonomous the proper use of the machine can be identified also in the operation of a single Foreseen modes of use The installation and the extraordinary maintenance of the machine must be carried out by qualified personnel only The machine has been designed to be used in a site having the following features Protection against atmospheric agents Proper illumination Allowed range of temperature from 18 C to 35 C Allowed humidity range from 30 to 80 Incorrect use of the machine 1 10 2 Any use other than that indicated in Section 1 10 1 Correct use of the machine is to be considered incorrect especially Using the machine in ways which differ from those which it has been designed for represents an anomalous condition and could therefore damage the structure of the machine Using the machine without its protections and without the safety equipment The non compliance with the procedures described in this manual and specially those concerning maintenance and repairing The use of the machine in a site whe
10. it in the lamp holder on the glass ceiling lamp Fig 4 e Plug the electric wire and switch lamp on or off using the through switch on the cable Fig STRONG trim PRO TECHNICAL SHEET REPLACEMENT OF ROTATING BLADES Follow this procedure to replace the blades or the rotating blades Remove the screws that fix the panel of the presser and remove it L Remove the screws that fix the presser plate and remove it 2 Remove the two screws that fix the front carriage to the back carriage 3 e Remove the screw that fixes the right cap to the front carriage 4 e Remove the screws that fix the left cap and push it away from carriage 5 e Remove the screws that fix the knob holder sheet from the front carriage STRONG trim PRO SCH TEC 1 TECHNICAL SHEET REPLACEMENT OF ROTATING BLADES e Push the front carriage towards the left to slide it out of its seat e Put the front part on a table slightly move the blade and remove the Benzing ring from its seat slide out the pin to replace the rotating blade 8 e Put the front panel back on the machine following the procedure in the reverse order 9 STRONG trim PRO SCH TEC 2 NEOLT spa Via G Galilei 8 24036 Ponte San Pietro BG ITALY 035 468811 MD 035 468886 NEOLT 2002
11. kness from 2mm up to max 4 5 mm Follow this procedure to cut media with thickness higher than 2mm until you reach a maximum of 4 5mm e Position the media to cut on the feeding table and use the brackets D to block the media so it doesn t slide e Perform the cut moving the blade holder carriage from right to left or vice versa 4 e Remove the trimmed media from the insertion table and the cut part from the paper collecting sheet e To perform a new cut repeat the operation described above We strongly recommend place any object on the insertion table Characteristics of the media to be cut 5 1 3 This trimmer has been designed to cut only media having the basic weight indicated in this manual see List of material Chapter 3 3 We recommend to not attempt to cut material having features different from the specified ones as the machine could be seriously damaged STRONG trim PRO MAINTENANCE Routine maintenance 6 1 Untimely movements during maintenance Be very careful Routine maintenance includes all the periodic and preventive operations enabling a safe use of the machine Qualification of the operator 6 1 1 Routine maintenance must be carried put only by qualified personnel Procedure 6 1 2 Perform the periodical operations listed in the following table Operation to be Frequency Procedure Cautions performed Dust removal When necessary e Wipe the whole su
12. ood illumination is required approximately 200 600 lux Environment features e Allowed temperature from 18 C to 35 C e Allowed relative humidity from 30 to 80 Testing 4 6 2 Before attempting the normal and continuous operation of the machine check its appropriate general operation by performing some test cuts LUI In case of malfunctioning find cause and or call NEOLT technical service STRONG trim PRO USE Qualification of the operator 51 The machine must be used by qualified personnel only Workplace 5 1 1 Position of the operator During start up and cutting operators positing is in front of the machine with the control panel in the centre In case of maintenance his position depends on the operation to be performed Insertion of the media to be cut 5 1 2 In case of media with 2mm thickness or lower To cut media 2mm thick or lower you can use the trimmer in a standard way by following this procedure e Position the media to cut on the feeding table and through the millimetric scales on the trimmer measure the cut 1 or line up the media to trim with the brackets D e Cut the media by moving the blade holder carriage from right to left or vice versa 2 e Remove the trimmed section from the machine and the cut part from the collection basket e perform another cut follow the above mentioned procedure STRONG trim PRO USE am For media with thic
13. re fire and explosion risks are present as the machine is not provided with explosion proof devices lts use in an explosive environment Its use in an inflammable environment STRONG trim PRO 1 5 GENERAL INFORMATION Structure of the machine The machine is composed of the following parts Work surface Support Paper collecting drape Brackets Blade holder carriage Sliding bar Fig 1 2 Detail STRONG 1 10 3 Fig 1 1 Prospect views trim PRO 1 6 INFORMATION ON SAFETY Safety criteria 2 1 During designing and manufacturing of this machine all criteria and care in order to satisfy the essential safety requirements foreseen by the relevant rules have been taken into account The accurate evaluation of the risks performed by the manufacturer has allowed to eliminate most of the risks concerning the usage conditions of the machine both foreseen and reasonably foreseeable The complete documentation including all the safety norms adopted is in the technical booklet of the machine which is deposited at the manufacturer s premises The manufacturer recommends strict compliance with the instructions procedures and recommendations of this manual and with the laws in force on the safety in the work place This also refers to the use of the protection devices foreseen both those integrated in the machine and personal S p A cannot be held responsible for any dam
14. rface of the Do not use aggressive machine with a wet cloth products Removal of When the waste e With a vacuum cleaner or Ware working gloves waste material material accumulation compressed air eliminate the IS EXCESSIVE accumulated waste material Extraordinary maintenance 6 2 For any extraordinary maintenance operation not described in this manual please contact directly NEOLT S p A STRONG trim PRO MAINTENANCE STRONG trim PRO 6 2 DISMAL TING Qualification of the operator 7 1 The dismantling of the machine must be performed by qualified personnel Deactivation of the machine 7 2 Once the machine has reached the end of its technical and operating life it must be deactivated The machine must be deactivated and put in the condition of not being used for the purposes which it had originally been designed for However it must allow the reuse of the raw materials which it was built with S p A cannot be held responsible for damages to people or pets due to the reutilization of single parts of the machine for purposes or in situations different from those which it has been designed for Procedure 7 2 1 e Incase the machine has to be displaced see section 5 2 Transport The machine is made of non biodegradable materials It must therefore be brought to authorized center for its disposal STRONG trim PRO DISMAL TING STRONG trim PRO 7 2 ATTACHMENTS
15. s section should be respected during temporary storage periods which could occur in the following situations e Installation of the machine delayed with respect of the delivery date e Deactivation of the machine and consequent storage while waiting for a new installation Characteristics 4 5 1 Temperature range allowed from 5 C to 35 C Humidity range allowed from 30 to 80 e Adequate artificial or natural illumination e Adequate protection against atmospheric agents e Sufficient clearance to perform the needed transport and lifting operations e Horizontal floor soace capable to hold the weight of the machine e Sufficient clearance to perform the Routine maintenance and service operations Characteristics of the location area 4 6 1 Space requirements For the normal operation of the machine loading and unloading operations included the needed space depends on the size of the media to be cut Protection against atmospheric agents The machine must be placed indoor in a room protected from the direct contact wit the atmospheric agents STRONG trim PRO INSTALLATION Floor requirements Prepare an horizontal supporting plane where to install the machine taking into account the weight of the machine itself and of all the ancillary devices am Optimal stability condition ca be achieved with a maximum planarity error of mm m Illumination For a proper operation and maintenance of the machine a g
16. sesesessessavacacsesesesesesenavaraeeeees 7 7 1 Qualification of the operator iii 7 1 7 2 Deactivation of the machine iii 7 1 KA FIOCCO rat 7 1 Chapter Attachment list 8 Attachment A Optonalreel holder A A 1 Assembly of optional reel holder iii A 1 Attachment B Optional sheet holder iii B B 1 Assembly of optional sheet holder B 1 B 2 Feeding Ne Media neuen B 3 Attachment C Optional cutting area C 1 Assembly Of lamp optional iii C 1 Attachment 1 Technical sheet rrereere eresie cere seeneenenee SCH TEC T1 1 Replacing rotating BLADES iii SCH TEC 1 STRONG trim PRO GENERAL INFORMATION Data of the manual 1 1 User s manual STRONG TRIM PRO Code of Manual NTL QR C N MM 2 1S GB Users 1 2 User s manual e Transporter e Installer e User e Maintenance personnel e Demolition squad For further details on the users of this manual please see Section 2 2 Qualification of the personnel Property of information 1 3 The information contained in this manual is reserved property All rights are reserved
17. tall the support assembling the lower traverse 3 and the upper one 4 with the right and left posts using the provided screws and bushing 5 LUI Attention The shoulder has holes with a different diameter the side with the bigger hole must face outward e assemble the stand screw on the bottom traverse 4 first to one shoulder then to the other with the screws and the bushes supplied 5 LUI Attention When you assemble the upper traverse the central push rod must face upwards 6 The value set by Neolt is 3 mm STRONG trim PRO 4 3 INSTALLATION To assemble the paper collection basket first slide in the front lower and then the back high basket holding rods and block them in the shoulder with two Benzing rings per rod 8 in the proper seats on the rod e Slide the square rods in the proper holes at the two ends of the basket e Fix the two rods to the basket holding rods previously assembled e Screw on the two supports for the table in the front part on the upper traverse using the supplied screws 10 STRONG trim PRO INSTALLATION As the trimmer is vary heavy wear proper working gloves and remember that for this operation minimum four persons are required e Place the trimmer on the assembled support 1 1 securing it on the support itself with the provided screws 2 on each side 12 During this operation move the feeding table of the trimmer to make fixing operations
18. the operator 4 1 Transport installation and connection operations must be performed only by personnel qualified in transportation and electrical operations Transport 4 2 Transport conditions 4 2 1 The trimmer is shipped with a packaging consisting of three cardboards 1 for components protection and of a carton box 2 containing all the components Fig 5 1 Transport conditions The packaging size and its gross weight trimmer plus packaging are the following Size WxDxH cm 213x52x34 263x52x34 370x52x34 Weight gross Kg Please use suitable lifting devices and accessories complying to the rules in force To avoid shocks and turnover apply the needed care Protect the machine against external atmospheric agents STRONG trim PRO INSTALLATION Fig 4 1 Transport conditions Assessment of damages during transportation 4 2 2 Check the conditions of the machine by visually inspecting it after having removed it from the shipping box Any defects on the visible parts of the machine indicate crashes during transportation which could also affect the ordinary operation of the machine In general check screws and bolts for tightness STRONG trim PRO INSTALLATION e Open the packaging box 1 containing all the components Fig 4 1 Transport conditions e Remove polystyrene protections 2 Fig 4 1 Transport conditions am For this operation minimum 4 persons are required e Ins
19. vented by carefully respecting the procedure indicated in this manual and using the indicated protection devices Some examples e Maintenance and service operations must be performed only by engineers authorized by the manufacturer e Pay attention to the warning labels applied to the trimmer S p A cannot be held responsible for any damages to people pets or objects due to noncompliance with the rules or if the prescribed individual protection equipment is not used IPE STRONG trim PRO INFORMATION ON SAFETY STRONG trim PRO 2 4 CHARACTERISTICS OF THE MACHINE Technical specifications Max cutting thickness mm 3 1 Usable cutting length cm Length cm Width cm Height with holder cm Height of working table cm Trim weight kg Support weight kg Accessories Performances Q Max cutting thickness STRONG Reel holder Cutting area lamp Sheet holder bar 3 2 4 5 mm trim PRO CHARACTERISTICS OF THE MACHINE List of material 3 3 strong TRIM pro Max cutting thickness 4 5mm Cibachrome Slides Acrylic film Hard board Hot seal film Lead Leather Lithoplate Magnetic vinyl Carton Paper Photographic film Photographic paper Polypropylene film Printing plate Polystyrene Rubber Steel for composite Fabrics Veneering boards STRONG trim PRO INSTALLATION Qualification of
20. void any possible danger for the people the material and the machine The description of direction sense and position right side of the machine left side of the machine refers to the operator standing in front of the machine Conventional symbols 1 4 2 Text in italic indicates the title of a chapter a section a sub section a paragraph a table or a figure of this manual or of another related publication 1 example of a generic number symbolic representation of a command or signaling device A _ example of generic letter symbolic representation of a part of the machine Notes contain important information given outside the text to which they refer The danger symbols indicate those procedures which if not respected could cause physical damages to the operator The manufacturer cannot be held responsible for any damages to people due to noncompliance with these norms The warning symbols indicate those procedures which if not respected could damage the machines or the devices connected to it The manufacturer cannot be held responsible for any damages to objects due to the noncompliance with these norms STRONG trim PRO 1 2 GENERAL INFORMATION neolt S p A Via G Galilei 8 24036 Ponte San Pietro BG ITALY Tel 035 468811 Fax 035 468886 http www neolt it E mail mkt neolt it STrONG TRIM PRO armer Year of construction Neolt spA ITALY MODEL SERIAL NBR

Download Pdf Manuals

image

Related Search

installation installation installation assistant installation directory installation folder installation media installation file installation art installation manager installation wizard installation assistant windows 11 installation solar power system installation made easy installation status report installation floater installation of mini split air conditioner installation solar panels installation definition installation status installation instructions installation file download installation guide installation manual installation has failed discord installation icon installation failed

Related Contents

    Haier HCR17W combi-fridge  MANUAL DO UTILIZADOR  Casio MO1011-EA User's Manual  Productivity 3000/ C  Xerox 4050 Printer User Manual    ELB-01(STAGEA mini )でお使いの場合  GE PowerGrid Design Files  

Copyright © All rights reserved.
Failed to retrieve file