WIC-100 User Manual
Contents
1. The AC adapter is used only for charging the monitor Do not cut the DC power cable of the AC adapter to fit with any other power source Attention should be drawn to the environmental aspects of the battery disposal Remove the batteries when cleaning the unit Remove the batteries before storing the unit for an extended period of time When necessary replace all four batteries in this unit with new ones Use only the size and type of batteries specified Be sure to install the batteries with the correct polarity as indicated in the battery compartment WARRANTY 1 Year Waranty This product is warranted to be free from defects in materials and workmanship and meet applicabe specifications when tested to ratings This warranty is in lieu of any other warranty express implied or statutory NTE s liability under this warranty is limited to repairing re placing or issuing credit at the discretion of NTE for such products that become defective or fail to meet specification during the warranty period of one year from the date of sale The technical data shown is intended to provide safe areas of operation for this product Determination as to whether a product is actually defective rests with NTE In no event will NTE be liable for consequential or special damages FCC INFORMATION This device complies with prat 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cuase harmful interfer2. recording Videos will be automatically saved as a file every 30 minutes The SD Card is full when the SD card icon changes to F 8 Taking Pictures 1 In the realtime monitoring mode press the button to enter the still mode as follows Battery Capacity Current Channel eee E e SD Card Icon Current 2009 02 11 Date 14 50 40 2 Press the OK button to take pictures The SD card is full when the SD card icon changes to A Y Da Playing Videos and Pictures 1 In the realtime monitoring mode press the button to enter into the following interface PLAYBACK 0001 0007 2009 01 10 2009 01 11 2009 01 12 2009 02 05 2009 02 09 2009 02 11 2 Press the or button to select a folder and then press the OK button to enter it 0002 0005 05 53 00 05 53 00 05 53 03 05 56 40 05 59 03 06 05 17 For Videos Press the or button to select video then press the OK button to play as follows C A OK H 2009 01 10 05 53 00 Pause Press the OK button in play mode to pause Press again to resume Fast Forward Press the button in play mode Fast Reverse Press the button in play mode Stop Exit Press the button For Pictures Press the or button to select picture then press the OK button to display and press the OK button again to exit The file with quotation marks is the picture file The file without quoatation marks is the vide
3. ECG User Manual Wireless Recordable Inspection Camera with Color LCD Monitor Model No WIC 100 Version No 1 0 Please read this user manual carefully before using this product CONTENTS Introduction Features Parts List Installation Operation Basic Operation Other Operations and Monitor Settings Record Videos Play Videos Delete Videos Pictures Language Setting Video System Setting Default Setup View Version Information Frame Rate Setting Time Stamp Setting Date Time Setting Event Playback SD Card CD Install and USC ccceceeeeceeeeeeeeeeeers 18 Specifications Warnings amp Warranty FCC Information INTRODUCTION Thank you for choosing our Wireless Inspection Camera with record able LCD monitor Please read this user manual carefully before using this product WIC 100 is designed as a remote inspection device It can be used to look into tight spots and beam back real time video to the monitor which records videos and takes pictures Typical applications include HVAC inspection automotive inspection cable routing automotive boat aircraft inspection electrical contracting pest control and home inspection FEATURES e 3 5 LCD monitor with a resolution of 320 RGB x 240 Supports many kinds of languages and features simple operation The camera and shaft are water resistant when the unit is fully assembled but the monitor and base unit are not Wired or Wireless Compatible Operation W
4. IC 100 records videos and takes pictures Can accept up to 16GB Micro SD Card PARTS LIST Software R Base Unit and Shaft w 9mm Camera Head gt Video Interconnect USB Cable LCD Monitor P Pa wee a Pagi ww Hook Magnet amp Mirror Accessories AC Adapter Micro SD Card 2GB Micro to Standard SD Adapter Magnetic Monitor Base FEATURES Camera Shaft and Base Unit rt Power Indicator Signal Output Flexible Shaft Power ON OFF Camera with 4SMD LEDs 3 5 LCD Monitor Power ON OFF Power Indicator USB Socket e _4 Video Output F SD Card Slot AC Adapter Input i DC5V lt Reset Signal Input INSTALLATION Please install the batteries and insert the SD card first before using this product To Install Batteries 1 Using a screwdriver remove the screw and battery cover 2 Remove the battery compartment and insert four new AA batteries into the proper slots in the battery compartment Proper battery orientation is indicated on the battery compartment 3 Reinstall the battery compartment battery cover and screw Moli Before installation or replacement of batteries make sure your hands are dry To Install The Camera With Flexible Shaft Connect the camera shaft to the base unit making sure the keyed ends are properly aligned Once they are aligned finger tighten the knurled knob to secure the connection 3 Keyed E
5. Language then press the OK button to enter the following interface see diagram at top of next page Language Setting Language 25 05 Sica OK V English 3 Press the or button to select a suitable language 4 Press the OK button to confirm and exit Video System Setting 1 In the setting mode press the or button to select SYS TEM SETTING then press the OK button to enter 2 Press the or buttons to select Video System then press the OK button to enter into the following interface Video System NTs NOTE NTSC NTSC N America PAL Europe NTSC 3 Press the or y button to select the right type then press the OK button to confirm and exit Format 1 In the setting mode press the or buttons to select SYS TEM SETTING then press the OK button to enter 2 Press the or buttons to select Format then press the OK button to enter into the following interface 13 FORMAT WILL ERASE ALL DATA ARE YOU SURE 3 Press the or y button to select YES then press the OK button to erase all data selecting NO will exit Default Setup 1 In the setting mode press the or button to select SYS TEM SETTING then press the OK button to enter 2 Press the or button to select Default Setup then press the OK button to enter into the following interface RESTORE DEFAULT ARE YOU SURE C
6. NOJ YES 3 Press the or button to select YES then press the OK button to restore default selecting NO will exit View Version Information 1 In the setting mode press the or button to select SYS TEM SETTING then press the OK button to enter 2 Press the or button to select Version then press the OK button to view the version of this product Version v905130 G0 14 Frame Rate Setting 1 In the setting mode press the or button to select RE CORDER SETTING then press the OK button to enter 2 Press the or button to select Frame Rate then press the OK button to enter the following interface Frame Rate 3 Press the or button to select a suitable frame rate 4 Press the OK button to confirm and exit Time Stamp Setting 1 In the setting mode press the or button to select RE CORDER SETTING then press the OK button to enter 2 Press the or button to select Time Stamp then press the OK button to enter the following interface Time Stamp ae 3 Press the or button to select OFF or ON then press the OK button to confirm and exit 15 Recording Type 1 In the setting mode press the or button to select RECORDER SETTING then press the OK button to enter 2 Press the or button to select Recording Type then press the OK button to enter into the followi
7. ence 2 This device must accept any interference received including interference that may case undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment Environmental Protection Electrical waste products should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice NTE Electronics Inc 44 Farrand Street Bloomfield NJ 07003 Phone 973 748 5089 Fax 973 748 6224 5 www nteinc com ECG isa regiesterd trademark of ELECTRONICS INC
8. nds Finger tighten the knurled knob Make sure to only tighten and untighten the knurled knob and not the shaft Installing Accessories The three included accessories mirror hook and magnet all attach to the shaft head the same way Aim here Slide the monitor downward Installing Magnetic Monitor Base Wireless Install as follows The magnetic monitor base features a rotational set to view from all angles 4 Inserting SD Card After the SD Card is inserted successfully into the SD card slot the screen of the moni tor will display the J icon otherwise it will display the A icon Connecting USB Cable Use the USB cable to connect the monitor to a PC The USB online icon will appear on your m ee PC Open My Computer and Hros Epresa noble find the Mobile Disk O Monitor Charging Connect the AC adapter to the monitor The power indicator will light red which indicates it is charging and it will turn off after fully charged Battery twinkles only when turned on and plugged in Monitor can be used while plugged in AC Adapter VIDEO OUT Insert the video interconnect cable into the monitor area labeled VIDEO OUT Insert the other end of the cable into the VIDEO IN jack of a TV or another monitor THE LCD monitor will output a high quality video which can be recorded e Video Out feature requires TV to be in line or video input mode e Video O
9. ng interface Recording Type VIDEO 3 Press the or y button to select STILL or VIDEO then press the OK button to confirm and exit Date Time Setting 1 In the setting mode press the or button to select Date Time then press the OK button to enter into the following inter face Date Time 2009 02 13 3 OK V 2 Press the OK button to select Date or Time Press or buttons to modify Press the button to confirm and exit 16 Event Playback 1 In the setting mode press the or button to select EVENT PLAYBACK then press the OK button to enter 2 For other operations see Play Videos amp Pictures Delete Vid eos amp Pictures amp Delete Folder sections Please be sure to fill out and re turn your Warranty Registration Card and return to NTE Electronics Inc 44 Farrand Street Bloomfield NJ 07003 If your Wireless Inspection Camera did not come with a Warranty Registration card please call 973 748 5089 immedi ately SPECIFICATIONS Actual transmission range may vary according to the weather location interference and building construction All specifications are subject to change without prior notice WARNINGS The monitor shall not be exposed to dripping or splashing liquid No objects filled with liquids shall be placed on the unit Turn off the Camera Monitor when the system is not in use
10. o file 10 Deleting Videos and Pictures 1 In the realtime monitoring mode press the button once to enter into the following interface PLAYBACK 0001 0007 2009 01 10 2009 01 11 2009 01 12 2009 02 05 2009 02 09 2009 02 11 2 Press the or y button to select a folder then press the OK button to enter into the following interface 2009 01 10 0002 0005 05 53 00 05 53 00 05 53 03 05 56 40 05 59 03 06 05 17 3 Press the or button to select a file then press and hold the button for two seconds and you will enter into the following interface 2009 01 10 0002 0005 DELETE CURRENT FILE 05 53 03 05 56 40 05 59 03 06 05 17 4 Press the or button to select YES then press the OK button to delete a file Select NO to exit 11 Delete Folder The delete folder is the same as the delete file however be cer tain that the folder is empty otherwise it will not delete and a warning will appear PLAYBACK 0001 0007 2009 01 10 2009 01 11 2009 01 12 2009 02 01 OLDER NOT EMPTY 2009 02 09 2009 02 11 How to enter the Setting Mode In the realtime monitoring mode press and hold the button for approximately 1 2 seconds to enter into the setting mode as follows SYSTEM SETTING 20 1 In the setting mode press the or buttons to select SYS TEM SETTING then press the OK button to enter 2 Press or button to select
11. ut feature may output a black and white signal OPERATION Basic Operation 1 Roll the ON OFF switch to turn ON the camera and the red power indicator will light The switch then acts as a dimmer for the LEDs that surround the camera and provide high quality lighting Four SMD LEDs provide lighting 2 Press and hold the Power ON OFF button of the monitor for 2 sec onds and the power indicator will light green Then press the but ton to select a suitable channel and the picture will display on the monitor Press the button to select video or picture status Select video or picture mode Select channel 3 Roll the ON OFF switch of the base unit for brightness adjust ment The switch acts as a dimmer wireless RE The flexible shaft can be bent into many shapes This helps you to explore into very small areas 5 The included handy acces sories of our wireless inspection camera can be used to retrieve small items like dropped rings or small screws Other Operations and Monitor Settings Record Videos 1 In the realtime monitoring status press the button to enter the Video status as follows Battery Capacity Current Channel E Frese PERRETE e SD Card Icon Current li 2009 02 11 00 45 43 oto e Time Left Date 14 50 40 2 Press the OK button to record as follows Recording 2009 02 11 00 05 43 paparan A Recorded Time 14 50 40 M Time Stamp 3 Press the OK button again to stop
Download Pdf Manuals
Related Search