Rayzor Beam 2R User Manual ver 1
Contents
1. 10 Be sure to reset the LAMP HOURS in the system menu to prevent the protection circuitry from accidently shutting off the lamp during normal operation 11 If the lamp protection circuitry has already been initiated and the LAMP HOURS is not reset the Replace the Lamp warning will continue to flash and fixture will eventually shut down To reset LAMP HOURS see instructions on the next page 16 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com LAMP HOURS RESET PROCEDURE 1 2 Activate the main menu by pressing MODE ESC and toggle to Information Press ENTER and press UP or DOWN to toggle to Time Information Press UP or DOWN to toggle to L Timer Password and press ENTER Then press UP or DOWN to enter the reset pass code 038 and press ENTER to confirm The display will automatically revert to L Timer Password next press UP or DOWN to toggle down to Clear Lamp Time Press ENTER and select ON The lamp timer has now been reset press MODE ESC to exit the menu and return to the home screen LAMP OPTIMIZATION Unlike traditional discharge lamps the Phillips Platinum 2R Lamp does NOT require optimization The lamp orientation and optimization procedure has been preset during the manufacturing process of the lamp Please remember the Phillips Platinum 2R Lamp is NOT a hot restrike lamp therefore you must wait approximately 15 minutes before you can attempt t2. www elationlighting com MOUNTING POINTS Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Fixture is fully operational in the specific mounting positions as illustrated below MAIA AS 2 WOW ee ee d i amp i je 9 var SA SZ L 2 SZ Gali eS SS DXX ax se m lt RUN LZ a Wa aca 2 NS N DEX fent tin ES SAFETY CABLE Always use a Safety Cable whenever installing this fixture in a suspended environment to ensure the fixture will not drop if the clamp fails 19 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com CLAMP MOUNTING The RAYZOR BEAM 2R provides a unique mounting bracket assembly that integrates the bottom of the base the included Omega Bracket and safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamps to the included omega bracket using a M10 screw fitted through the center hole of the Omega Bracket Be sure to attach the included Safety Cable to the fixture using the safety cable rigging point integrated in the base
3. Edit Scene 250 Secne Time manual scenes edit Input By Exterior Rec Controller XX XX Automat scenes rec FUNCTION Set DMX Address Define desired DMX address via the Control Panel FUNCTION DMX Value Display DMX 512 value of each channel FUNCTION Set To Slave Define fixture slave mode Slavel Slave2 Slave3 FUNCTION Auto Program Define fixture mode Master or Alone for running Auto Programs Select desired internal programs under Select Program set the number of steps under Edit Program and edit individual scenes u FUNCTION Sound Control nder Edit Scenes Define fixture mode Master or Alone for running Auto Programs via sound activation default is Master 27 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com INFORMATION Time Information Current Time Displays fixture run time from last power ON The counter is reset after each time the fixture is powered OFF INFORMATION Time Information Total Run Time Displays fixture total run time INFORMATION Time Information Last Run Time Displays fixture run time for a given period of time i e rental period This counter can be reset INFORMATION Time Information Lamp Hours Displays lamp total run time This counter should be reset at each lamp change INFORMATION Time Information Lamp Off Time Displays lamp run time from the last power ON This co
4. This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line Using a line terminator will decrease the possibilities of erratic behavior f Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable to connect DMX terminal Resistance 420 Ohm 1 4 W between PIN 2 DMX P and PIN 3 DMX of the last fixture PIN2 5pin XLR DMX CONNECTORS Some manufactures use 5pin XLR Connectors for DATA transmission in place of 3pin 5pin XLR fixtures may be implemented in 3pin XLR DMX line When inserting standard 5pin XLR connectors in to a 3pin line a cable adaptor must be used these adaptors are readily available at most electric stores The following chart details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 XLR Male In Data True signal Pin 3 Pin 4 Do Not Use 23 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com DMX ADDRESSING All fixtures should be given a DMX starting address when using a DMX controller so the correct fixture resoonds to the correct control signal This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting DMX address is achieved by setting the correct DMX address on th
5. 12 RAYZOR BEAM 2R User Manual Ver 1 Erarop www elationlighting com 2 Gently remove 2 Red Wires connected to spade terminals on base of lamp 3 Using your thumb and index finger gently squeeze the retention clips together in the direction illustrated by the to unlock them 13 RAYZOR BEAM 2R User Manual Ver 1 Erariop www elationlighting com 4 Move the retention clips in the direction illustrated by the 5 Gently remove the lamp out and away from the fixture 14 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com 6 Using a clean cloth or gloves gently install the new lamp into the fixture making sure the lamp is seated correctly straight and flush against the base 7 Using your thumb and index finger gently squeeze the retention clips together in the direction illustrated by the to lock them into place mI m 15 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com 8 Gently attached 2 Red Wires connected to spade terminals on base of lamp 9 Replace the lamp cover plate back into place by securing 3 screws marked C ow N 454545 T 90 C LAMP PLATINUM 2R 4 CAUTION HOT LAMP Let the lamp cool down for 10 min Change the lamp by loosening screws A B C Lamp MUST BE replaced at 6 000 Hours Use only Genuine Original Phil platinum lamps Other brand lamps may cause damage Cs and void warranty L
6. EtATION RAYZOR BEAM 2R M User manual wiz wvasxozivi NOILV 13 www elationlighting com 2014 ELATION PROFESSIONAL all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ELATION brands and product names are trademarks or registered trademarks of their respective companies ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe insufficient and negligent assembly installation rigging and operation of this product Elation Professional USA 6122 S Eastern Ave Los Angeles CA 90040 323 582 3322 323 832 9142 fax www elationlighting com info elationlighting com Elation Professional B V Junostraat 2 6468 EW Kerkrade Netherlands 31
7. Program 2 includes scenes 10 11 12 amp 13 Program 4 includes scenes 8 9 amp 10 Program 6 includes scenes 12 13 14 amp 15 Auto Pro Part 1 is Program 2 Auto Pro Part 2 is Program 3 Auto Pro Part 3 is Program 6 The 3 Slave groups run the Auto Program in certain time segments as shown in the following picture Part 1 emn eme o Part 2 eleme me 9m Part 3 35 RAYZOR BEAM 2R User Manual Ver 1 EtATION PROFESSIONAL www elationlighting com DMX CHANNEL FUNCTIONS AND VALUES RAYZOR BEAM 2R DMX Channel Values Functions 16 DMX Channels Specifications are subject to change without any prior written notice Rotation direction Clockwise or Counterclockwise of COLOR GOBO and PRISM effects depends on the orientation of the fixture head MODE CHANNEL VALUE FUNCTION BASIC STAND EXTEND 1 1 1 PAN MOVEMENT 8 BIT 0 255 PAN Movement By 540 630 2 PAN FINE MOVEMENT 16 BIT 0 255 PAN Movement FINE Adjustment 0 255 ILT Movement By 270 4 4 TILT MOVEMENT 16 BIT 0 255 ILT Movement FINE Adjustment E 0 8 OPEN WHITE 9 17 RED 18 26 BLUE 27 35 GREEN 36 44 YELLOW 45 53 MAGENTA 54 62 LIGHT BLUE 63 71 ORANGE d 2 7280 PINK 81 89 GOLD 90 98 NAVY BLUE 99 107 UV FILTER 108 116 CTO 117 127 CTB 128 189 Clockwise Color Rotation from FAST
8. Shutter Open s ao O E 0 255 Dimmer Intensity 0 to 100 4 _ O 0 255 Dimmer Intensity FINE Adjustment 0 225 PAN TILT MAX to MIN Speed 9 11 15 226 235 Blackout by Movement 236 245 Blackout by ALL Wheel Changing 246 255 O Function 38 RAYZOR BEAM 2R User Manual Ver 1 ELATIO www elationlighting com ELATIONO RAYZOR BEAM 2R DMX Channel Values Functions 16 DMX Channels Specifications are subject to change without any prior written notice Rotation direction Clockwise or Counterclockwise of COLOR GOBO and PRISM effects depends on the orientation of the fixture head MODE CHANNEL VALUE FUNCTION BASIC STAND EXTEND LAMP ON OFF RESET INTERNAL PROGRAMS 0 19 COLOR Change Normal 20 29 COLOR Change to Any Position 30 39 COLOR amp GOBO Change to Any Position 40 59 LAMP ON Value must be maintained for 3 sec 60 79 LAMP Switch OFF Value must be maintained for 3 sec 80 84 ALL Motor Reset Value must be maintained for 3 sec 85 87 SCAN Motor Reset Value must be maintained for 3 sec 88 90 COLORS Motor Reset Value must be maintained for 3 sec 91 93 GOBO Motor Reset Value must be maintained for 3 sec 94 96 SHUTTER amp DIMMER Motor Reset Value must be maintained for 3 sec 97 99 OTHER Motor Reset Value must be maintained for 3 sec 100 119 ntemal Program 1 120 139 ntemal Program 2 140 159 Intemal Program 3 160 179 Internal Program 4
9. 180 199 Internal Program 5 200 219 Internal Program 6 220 239 Intemal Program 7 240 255 Auto Program by Music Control 39 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com ERROR CODES When power is applied the unit will automatically enter a Reset Test mode This mode brings all the internal motors to a home position If there is an internal problem with one or more of the motors an error code will flash in the display in the form of XXer were as XX will represent a function number For example when the display shows it means there is some type of error with the Pan motor If there are multiple errors during the start up process they will all flash in the display For example if the fixtures has errors on Channel 1 2 and 5 all at the same time you will see the error message O3Er and O5Er flash repeated 5 times If an eror does occur during the initial start up procedure the fixture will self generate a second reset signal and try to realign all the motors and correct the errors If the error persists after a second attempt a third attempt will be made If after a third attempt all the errors have not been corrected the fixture will make the following determinations 3 or More Errors The fixture cannot function properly with three or more errors therefore the fixture will place itself in a stand by mode until subsequent repairs
10. Macros COLOR 13 Dichroic Colors Including UV CTO CTB White GOBOS 14 Static Gobos Including 6 Multi Sized Beams CONTROL CONNECTIONS 3 DMX Channel Modes 10 12 16 Pan Movement 540 630 Tilt Movement 270 6 Button Control Panel Full Color 180 Reversible LCD Menu Display 16 Bit 3 Phase Pan Tilt Motors 5pin DMX In Out powerCON In Out SIZE WEIGHT Length 11 6 295mm Width 9 6 245mm Vertical Height 16 6 421mm Weight 23 0 Ibs 10 4 kg ELECTRICAL THERMAL AC 100 240V 50 60Hz 230W Max Power Consumption 14 F to 113 F 10 C to 45 C APPROVALS RATINGS CE IP20 Intertek INSTALLATION Rigging Omega Bracket Working Position Flat Surface Inverted 180 Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 43 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com COLORS GOBOS 1 Red 2 Blue 3 Green 4 Yellow 5 Magenta 6 Light blue 7 8 Pink 9 Gold 10 blue 11 UV Filter 12 CTO 13 CTB o OO A A 0 qq v lt e e e 22 2 Qc PHOTOMETRIC DATA 3 Beam 15m 20m 25m m ft m ft m ft Distance 15 49 2 20 65 6 25 82 0 3 Beam Diameter lux fe FULL ON 49 470 4 596 29 300 2 722 19 200 1 784 Please Note Specifications and improvements in the design of this unit and this manual are subject to change
11. PID Code a Shutoff Time 02 60m 05m Display shutoff time Display Setting Display Reverse ON OFF Reverse 180 degree Key Lock ON OFF Key Lock Celsius Temperature switch Fahrenheit between C F Initial Status PAN EARRA Initial effect position Reset Default ON OFF Restore factory set E Reset All Reset all motors 2 Reset Pan amp Tilt Reset Pan Tilt e Reset Colors Reset color wheel Tul Reset Gobos Reset gobos 9 Reset Shutter Reset shutter or dimmer E Reset Others Reset other motors 26 RAYZOR BEAM 2R User Manual Ver 1 EraTiow eLATION www elationlighting com Test Channel PAN Test function v PAN XXX Fine adjustment of the 3 Manual Control 5 P lamp 9 Calibrate Password Pae Ward E Calibration Color wheel XXX ing ENE effects to standard right position Standard Mode A Basic Mode Extended Mode User s mode to change E Uest Mode User Mode A channel numbers User Mode B User Mode a Max Channel XX Edit User Mode PAN CHO1 Preset User modes Auto Pro Part 1 Program 1 10 Program 1 Select programs to be Select Programs Auto Pro Part 2 Program 1 10 Program 2 ae Auto Pro Part 3 Program 1 10 Program 3 S Program 1 Program Test Testing program o Edit Program Step 01 SCxxx Program in loop Program 10 Step 64 SCxxx Save and exit Pan Tilt Edit Scenes Edit Scene 001 Fade Time ao automatically
12. User Manual Ver 1 www elationlighting com EFFECT ADJUST Calibration 3 ONLY QUALIFIED TECHNICIANS SHOULD PERFORM THIS FUNCTION This function allows small adjustments to be made to the effect wheels Color Gobo Shutter etc to compensate for ware or in the event a sensor has been knocked slightly out of place Because improper use of this function can result in undesired operation this function has been password protected The password is 050 and must be entered each time the calibration menu function is entered Because calibration is an extremely delicate procedure instructions on performing this action are left out of this manual For a first time calibrator please contact our customer support team for step by step instructions USER MODE SET User Mode Select operating mode which includes DMX Channel and User defined modes USER MODE SET Edit User Mode Create user defined channel orders allowing the fixture to match the channel order of other fixtures on the market for easier operation A total of three user modes may be configured User Mode A User Mode B and User Mode C EDIT PROGRAM Select Program Select one of the 10 user defined internal Auto Programs EDIT PROGRAM Edit Program Edit any of the 10 user defined internal Auto Programs EDIT PROGRAM Edit Scenes Edit any of the scenes of the internal Auto Programs EDIT PROGRAM Record Controller The fixture features an integrated DMX recor
13. can be made Less Than 3 Errors The fixture has less than 3 errors therefore most other functions will work properly The fixture will attempt to operate normally until the errors can be correct by a technician The errors in question will remain flashing in the display as a reminder of internal errors 40 RAYZOR BEAM 2R User Manual Ver 1 ELATIO www elationlighting com ELATIONO RAYZOR BEAM 2R ERROR CODES Specifications and features are subject to change without any prior written notice ERROR CODE DESCRIPTION The PAN movement is not located in the default position after the reset OlEr This message will appear after a fixture reset if the magnetic indexing circuit malfunctions sensor failed or magnet is missing or there is a motor failure defective motor or a defective motor IC drive on the main PCB PAN Error This error may also be displayed if the head yoke was blocked during a reset function The TILT movement is not located in the default position after the reset O3Er This message will appear after a fixture reset if the magnetic indexing circuit malfunctions sensor failed or magnet is missing or there is a motor TILT Error failure defective motor or defective motor IC drive on main PCB This error may also be displayed if the head was blocked during a reset function The Color Wheel is not located in the default position after the reset 05 This message will appear after the reset of the fi
14. to SLOW 190 193 NO Rotation 194 255 Counterclockwise Color Rotation from SLOW to FAST 0 255 Color Wheel FINE Adjustment to Any Position 36 RAYZOR BEAM 2R User Manual Ver 1 EtATION PROFESSIONAL www elationlighting com ELATIONO RAYZOR BEAM 2R DMX Channel Values Functions 16 DMX Channels Specifications are subject to change without any prior written notice Rotation direction Clockwise or Counterclockwise of COLOR GOBO and PRISM effects depends on the orientation of the fixture head MODE CHANNEL VALUE FUNCTION BASIC STAND EXTEND 0 7 OPEN 8 15 Gobo 1 16 23 Gobo 2 24 31 Gobo 3 32 39 Gobo 4 40 47 Gobo 5 48 55 Gobo 6 56 63 Gobo 7 64 71 Gobo 8 72 79 Gobo 9 80 87 Gobo 10 88 95 Gobo 11 96 103 Gobo 12 104 111 Gobo 13 4 6 7 112 119 Gobo 14 120 126 Gobo 1 Shake From SLOW to FAS 127 133 Gobo 2 Shake From SLOW to FAS 134 140 Gobo 3 Shake From SLOW to FAS 141 147 Gobo 4 Shake From SLOW to FAS 148 154 Gobo 5 Shake From SLOW to FAS 155 161 Gobo 6 Shake From SLOW to FAS 162 168 Gobo 7 Shake From SLOW to FAS 169 175 Gobo 8 Shake From SLOW to FAS 176 182 Gobo 9 Shake From SLOW to FAS 183 189 Gobo 10 Shake From SLOW to FAST 190 196 Gobo 11 Shake From SLOW to FAST 197 203 Gobo 12 Shake From SLOW to FAST 204 210 Gobo 13 Shake From SLOW to FAST 211 217 Gobo 14 Shake From S
15. warranties of merchantability or fitness are limited in duration to the warranty periods set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said periods have expired The consumer s and or dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall Elation Professional amp be liable for any loss and or damage direct and or consequential arising out of the use of and or the inability to use this product This warranty is the only written warranty applicable to Elation Professional amp products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published RAYZOR BEAM 2R User Manual Ver 1 ELATIO www elationlighting com SAFETY INSTRUCTIONS The RAYZOR BEAM 2R is an extremely sophisticated piece of electronic equipment To guarantee a smooth operation it is important to follow the guidelines in this manual The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual This device falls under PROTECTION CLASS 1 It s essential this device be grounded properly Only qualified personnel should perform all electrical connections KEEP THIS FIXTURE AWAY FROM RAIN AND MOISTURE UNPLUG POW
16. without any prior written notice 44 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com DIMENSIONAL DRAWINGS 16 6 16 1 421mm 408mm pil w LI 199mm 45 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com CIRCUIT SCHEMATICS RAYZOR BEAM 2R Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 46 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com OPTIONAL ACCESSORIES ORDER CODE ITEM TRIGGER CLAMP Heavy Duty Wrap Around Hook Style Clamp DRCRAY2R Six Pack Road Case For Rayzor Beam 2R EWDMXSYSTEM Wireless DMX Systern 1 Transmitter 1 Receiver EWDMXT Wireless DMX Transmitter EWDMXR Wireless DMX Receiver ACSPDMXSPRO 5 ft 1 5m 5pin PRO DMX Cable Additional Cable Lengths Available 47 RAYZOR BEAM 2R User Manual Ver 1
17. you need any spare parts please order genuine parts from your local Elation dealer Please refer to the following points during routine inspections A detailed electric check by an approved electrical engineer every three months to make sure the circuit contacts are in good condition and prevent overheating e Be sure all screws and fasteners are securely tightened at all times Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall e Check for any deformations on the housing color lenses rigging hardware and rigging points ceiling suspension trussing Deformations in the housing could allow for dust to enter into the fixture Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person s Electric power supply cables must not show any damage material fatigue or sediments Never remove the ground prong from the power cable 42 RAYZOR BEAM 2R User Manual Ver 1 EtATION www elationlighting com TECHNICAL SPECIFICATIONS FEATURES 3 Sharp Narrow Beam Super Fast 16 bit 3 Phase Pan and Tilt Motors CTO and CTB Color Correction Flicker Free Operation for TV and FILM Remote Device Management Protocol Support SOURCE 132W Platinum 2R Lamp 6 000 Hour Average Life PHOTOMETRIC DATA 49 470 LUX 4596 FC 42 9 15M 7 500K gt 75 CRI EFFECTS Strobe 1 13 fps Electronic Dimming 096 10096 8 Facet Rotating Prisms and
18. 45 546 85 66 31 45 546 85 96 fax www elationlighting eu info elationlighting eu DOCUMENT VERSION LE Please check www elationlighting com for the latest revision update of this manual Document Software DMA Date Version Verion Cannel Medes Notes 2 2015 gt 1 1 4 10 12 16 Initial release 2 RAYZOR BEAM 2R User Manual Ver 1 CONTENTS www elationlighting com General Information 4 Warranty 6 Safety Instructions 7 General Guidelines 8 Discharge Lamp Warning 9 Fixture Overview 10 Lamp Installation Instructions 11 Fixture Installation 18 Understanding DMX 2 Fixture Menu 25 DMX Channel Functions And Values 35 Error Codes 38 Cleaning and Maintenance 40 Technical Specifications 41 Optional Accessories AS RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com GENERAL INFORMATION INTRODUCTION Congratulations you have just purchased one of the most innovative and reliable lighting fixtures on the market today The RAYZOR BEAM 2R has been designed to perform reliably for years when the guidelines in this booklet are followed Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit These instructions contain important information regarding safety during use and maintenance UNPACKING Thank you for purchasing the RAYZOR BEAM 2R by Elation Prof
19. ER BEFORE SERVICING FIXTURE NEVER TOUCH FIXTURE DURING OPERATION AS IT MAY BE HOT NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE SENSITIVE PERSONS MAY SUFFER AN EPILETIC SHOCK A A e For proper operation follow the Installation guidelines described in this manual Only qualified and certified personnel should perform installation of this fixture and only the original rigging parts brackets included with this fixture should be used for installation Any modifications will void the original manufactures warranty and increase the risk of damage and or personal injury s Never look directly into the light source of this fixture to prevent risk of injury to your retina which may induce blindness Those suffering from EPILEPSY should avoid looking directly into the light source of this unit at all times The fan and air inlets must remain clean and never blocked Allow approx 6 15cm between this fixture and other devices or a wall for proper cooling e Always disconnect from main power source before performing any type of service and or cleaning procedure Only handle the power cord by the plug end never pull out the plug by tugging the wire portion of the cord Do not operate this fixture if the power cord has become frayed crimped and or damaged If the power cord is damaged replace it immediately with a new one of similar power rating 7 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com GENERAL GUIDEL
20. INES NEVER OPEN THIS FIXTURE WHILE IN USE During the initial operation of this fixture a light smoke or smell may emit from the interior of the fixture This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time This fixture is a professional lighting effect designed for INDOOR DRY LOCATIONS ONLY on stage in nightclubs theatres etc Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while operating to prevent any fire hazard Minimum distance to lighted objects must be 16 4 feet 5m Maximum temp of the external surface 194 F 90 C Minimum distance of inflammable materials from the surface 1 6 feet 0 5m The fixture must be installed in a location with adequate ventilation at least 1 5 feet 5m from adjacent surfaces Be sure no air ventilation slots are blocked DO NOT attempt installation and or operation without knowledge how to do so DO NOT allow operation by persons who are not qualified to operate this type of fixture Most damages are the result of operations by nonprofessionals Consistent operational breaks may ensure the fixture will function properly for many years to come DO NOT shake fixture avoid brute force when installing and or operating fixture Always install the fixture with an appropriate safety cable When installing the fixture in a suspended environmen
21. LOW to FAST 218 255 Clockwise Fixed Gobo Wheel Rotation From SLOW to FAST 0 255 Fixed Gobo FINE Indexing RAYZOR BEAM 2R User Manual Ver 1 EtATION www elationlighting com RAYZOR BEAM 2R DMX Channel Values Functions 16 DMX Channels Specifications are subject to change without any prior written notice Rotation direction Clockwise or Counterclockwise of COLOR GOBO and PRISM effects depends on the orientation of the fixture head MODE CHANNEL VALUE FUNCTION BASIC STAND EXTEND 8 FACET ROTATING PRISM PRISM GOBO MACROS 0 31 OPEN 32 127 8 Facet Prism 28 135 acro 1 36 143 lacro 2 44 151 acro 3 52 159 acro 4 60 167 acro 5 68 175 acro 6 5 7 9 76 183 acro 7 84 191 acro 8 92 199 acro 9 200 207 acro 10 208 215 acro 11 216 223 acro 12 224 231 acro 13 232 239 acro 14 240 247 acro 15 248 255 acro 16 0 127 Prism Index Rotation 6 8 10 128 189 Clockwise Prism Rotation from FAST to SLOW 190 193 O Rotation 194 255 Counterclockwise Prism Rotation from SLOW to FAST 0 255 Prism FINE Indexing OB 0 31 Shutter CLOSED 32 63 O Function Shutter OPEN 64 95 Strobe Effect SLOW to FAST 7 9 12 96 127 O Function Shutter OPEN 128 159 Pulse Effect In Sequences 160 191 O Function Shutter OPEN 192 223 Random Strobe Effect SLOW to FAST 224 255 O Function
22. SONALITY Temperature C F Define how fixture displays internal temperature Celsius or Fahrenheit 30 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com PERSONALITY Initial Status Create custom PAN TILT and Effect settings and save as a custom Horne Position PERSONALITY Reset Default When ON all factory settings are restored RESET FUNCTION Reset ALL Reset ALL internal motors to Horne Position RESET FUNCTION Reset PAN and TILT Reset only PAN and TILT motors to Horne Position RESET FUNCTION Reset Colors Reset only Color Wheel to Horne Position RESET FUNCTION Reset Gobos Reset only Gobo Wheels to Horne Position RESET FUNCTION Reset Shutter Reset only blackout Shutter to Home Position RESET FUNCTION Reset Others Reset ALL other motors not associated previously listed commands to Horne Position EFFECT ADJUST Test Channel Select and auto test each individual channel function independently from the DMX control board EFFECT ADJUST Manual Control Select and manually test and fine adjust each individual channel function Independently from DMX control board This function will center PAN and TILT motors and set dimmer to 10096 PAN and TILT functions will still operate if the fixture needs to be positioned to a flat clear surface With the individual functions you can focus the light on a flat surface wall and perform fine adjustments 31 RAYZOR BEAM 2R
23. assembly SECURING Regardless of the rigging option you choose for your RAYZOR BEAM 2R always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle 20 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com UNDERSTANDING DMX DMX 512 DMX is short for Digital Multiplex This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers DMX allows all makes and models of different manufactures to be linked together and operate from a single controller This is possible as long as all the fixtures and the controller are DMX compliant A DMX controller sends the DMX data instructions to the fixture allowing the user to control the different aspects of an intelligent light DMX data is sent out as serial data that travels from fixture to fixture via data IN and data OUT XLR terminals located on the fixtures most controllers will only have output jacks DMX LINKING To ensure proper DMX data transmission always use proper DMX cables and a terminator When using several DMX fixtures try to use the shortest cable path possible Never split a DMX line with a Y style connector The order in which the fixtures a
24. ax 31 45 546 85 96 E mail support elationlighting eu WARRANTY REGISTRATION Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping container If the unit is under warranty you must provide a copy of your proof of purchase invoice Items returned without a R A number clearly marked on the outside of the package will be refused and returned at customer s expense You may obtain a R A number by contacting customer support at 323 582 3322 IMPORTANT NOTICE TS There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty Damages resulting from modifications to this fixture and or the disregard of safety and general user instructions found in this user manual void the manufactures warranty and are not subject to any warranty claims and or repairs 5 RAYZOR BEAM 2R User Manual Ver 1 ELATIO www elationlighting com LIMITED WARRANTY A Elation Professional hereby warrants to the original purchaser Elation Professional products to be free of manufacturing defects in material and workmanship
25. der by which you can transmit the programmed scenes from your DMX controller to the moving head Adjust the desired scene numbers via the encoder from to When you call up the scenes at your controller they will automatically be transmitted to the moving head 32 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com EDIT PROGRAM Record Controller Working With Built In Programs A Master unit can send up to 3 different data groups to the Slave units i e a Master unit can start 3 different Slave units which run 3 different programs The Master unit sends the 3 program parts in a continuous loop Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 The Slave unit receives data from the Master unit according to the group which the Slave unit was assigned to If e g a Slave unit is set to Slave 1 in the menu Set to Slave the Master unit sends Auto Program Part 1 to the Slave unit If set to Slave 2 the Slave unit receives Auto Program Part 2 To start an Auto Program proceed as follows 1 Slave Setting e Select Function Mode Press ENTER to confirm Select Set to Slave Press ENTER to confirm Select Slave 1 Slave 2 or Slave 3 Press ENTER to confirm Press MODE ESC in order to return to the main menu 2 Automatic Program Run e Select Function Mode Pres
26. e digital display located on the back of the fixture You can set the same starting address for all fixtures or a group of fixtures or set different address for each individual fixture Be advised that setting all fixtures to the same DMX address will subsequently control all fixtures in the same fashion in other words changing the settings of one channel will affect all the fixtures simultaneously If you set each fixture to a different DMX address each unit will start to listen to the channel number you have set based on the quantity of control channels DMX channels of each fixture That means changing the settings of one channel will only affect the selected fixture In the case of the RAYZOR BEAM 2R when in the 16 Channel Extended Mode you should set the starting DMX adaress of the first unit to 1 the second unit to 17 16 1 the third unit to 33 17 16 and so on Note During start up the RAYZOR BEAM 2R will automatically detect whether a DMX data signal is being received or not If DMX data signal is being received the display will show AddrzXXX XXX representing the actual DMX adaress If the fixture is not receiving a DMX signal the display will flash If your fixture is connected to a DMX controller and the display is flashing not receiving a DMX signal please check the following The or Spin XLR input plug cable with DMX signal from controller is not connected or is not inserted completely into
27. e lamp has been automatically shut OFF LAMP CONTROL Lamp OFF Temp The fixture is designed to shut the lamp OFF when an excessive temperature is sensed inside the head by the on board CPU The lamp is shut OFF to prevent damage to the lamp and avoid possible internal damage to the fixture head This function sets the MAX internal operating temperature of the fixture head when the lamp will automatically be shut OFF PERSONALITY Status Settings Address Via DMX When ON define the desired DMX address via an external controller 1 Connect the fixture to the external controller and power ON 2 Set the DMX value of Channel 1 on the controller to 7 3 Set the DMX value of Channel 2 on the controller to 7 or 8 When set to 7 the DMX adaress can be set between 1 and 255 When set to 8 the DMX adaress can be set between 256 and 511 4 Using Channel 3 on the controller set the desired DMX address of the fixture Example 1 If the desired DMX address is 57 set Channel 1 to a value of 7 set Channel 2 to a value of 7 and then set Channel 3 to a value of 57 Example 2 If the desired DMX address is 420 set Channel 1 to a value of 7 set Channel 2 to a value of 8 and then set Channel 3 to a value of 164 256 164 420 5 After setting Channel 3 to the desired DMX adaress value wait for approximately 20 seconds for the fixture to complete the address reset function PERSONALITY Status Settin
28. essional Every RAYZOR BEAM 2R has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your unit for damage and be sure all accessories necessary to operate the unit have arrived intact In the event damage has been found or parts are missing please contact our customer support team for further instructions Please do not return this unit to your dealer without first contacting customer support at the number listed below Please do not discard the shipping carton in the trash Please recycle whenever possible BOX CONTENTS 1 Omega Bracket e 1 5pin DMX Cable 1 powerCON Cable e 1 Safety Cable Manual amp Warranty Card 4 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com CUSTOMER SUPPORT Elation Professionale provides a customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www elationlighting com for any comments or suggestions For service related issue please contact Elation Professional ELATION SERVICE USA Monday Friday 8 00am to 5 00pm PST Voice 323 582 3322 Fax 323 832 9142 E mail support elationlighting com ELATION SERVICE EUROPE Monday Friday 08 30 to 17 00 CET Voice 31 45 546 85 30 F
29. for a period of two years 730 days and Elation Professional product rechargeable batteries to be free of manufacturing defects in material and workmanship for a period of six months 180 days from the original date of purchase This warranty excludes discharge lamps and all product accessories This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service send the product only to the Elation Professional factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty Elation Professional will pay return shipping charges only to a designated point within the United States If any product is sent it must be shipped in its original package and packaging material No accessories should be shipped with the product If any accessories are shipped with the product Elation Professional shall have no liability what so ever for loss and or or damage to any such accessories nor for the safe return thereof C This warranty is void if the product serial number and or labels are altered or removed if the product is modified in any manner which Elation Professional concludes after inspection affects the reliability of the product if t
30. gs No DMX Status Define how fixture operates if NO DMX signal is detected 29 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com PERSONALITY Status Settings Pan Invert When ON all PAN movernents are reversed inverted PERSONALITY Status Settings Tilt Invert When ON all TILT movements are reversed inverted PERSONALITY Status Settings Pan Degree Select desired maximum degree of the Pan movement PERSONALITY Status Settings Feedback When ON the fixture automatically performs PAN TILT correction in the event either one is disrupted during normal operation PERSONALITY Status Settings Movement Speed Select desired Movement Speed PERSONALITY Status Settings Mic Sensitivity Select desired Microphone Sensitivity PERSONALITY Status Settings Hibernation Select desired Hibernation time PERSONALITY Service Setting Password Displays the service setting password 050 PERSONALITY Service Setting RDM PID RDM Remote Device Management PERSONALITY Display Setting Shutoff Time Define how many minutes before the LCD Menu display will automatically shut OFF PERSONALITY Display Setting Display Reverse When ON the LCD Menu display by is rotated inverted 180 PERSONALITY Display Setting Key Lock When ON Control Panel buttons lock automatically after exiting main menu for 15 seconds To unlock keep MODE ESC button pressed for 3 seconds PER
31. he product has been repaired or serviced by anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser by Elation Professional if the product is damaged because not properly maintained as set forth in the product instructions guidelines and or user manual D This is not a service contract and this warranty does not include any maintenance cleaning or periodic check up During the periods as specified above Elation Professional will replace defective parts at its expense and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of Elation Professional under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of Elation Professional All products covered by this warranty were manufactured after January 1 1990 and bare identifying marks to that effect E Elation Professional reserves the right to make changes in design and or performance improvements upon its products without any obligation to include these changes in any products theretofore manufactured F No warranty whether expressed or implied is given or made with respect to any accessory supplied with the products described above Except to the extent prohibited by applicable law all implied warranties made by Elation Professional in connection with this product including
32. his or any fixture fitted with a gas discharge lamp UV RADIATION NOTICE This fixture emits intense UV radiation which is harmful to the eyes and skin The intense luminance of the lamp can cause severe damage to the retina NEVER operate this fixture with ANY of the protective covers removed These covers have been specially designed to shield against UV radiation LAMP REPLACEMENT Please note that due to the nature of the Phillips Platinum 2R Lamp and the optical path of the Elation RAYZOR BEAM 2R fixture the lamp MUST BE replaced at 6 000 hours Use only Genuine Original Phillips platinum lamps Other brand lamps may cause damage and void warranty 9 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com FIXTURE OVERVIEW 10 11 12 13 14 15 LENS LCD Menu Function Display Microphone LEFT Button DOWN Button ENTER Button RIGHT Button MODE ESC Button UP Button Carrying Handle s Lamp Access Cover Panel DMX Input 5pin DMX Output powerCON Input Fuse RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com LAMP INSTALLATION INSTRUCTIONS LAMP REPLACEMENT Please note that due to the nature of the Phillips Platinum 2R Lamp and the optical path of the Elation RAYZOR BEAM 2R fixture the lamp MUST BE replaced at 6 000 hours Use only Genuine Original Phillips Platinum 2R Lamps Other brand lamps may cause damage and void wa
33. o restrike the lamp once it has been turned off 17 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com FIXTURE INSTALLATION FLAMMABLE MATERIAL WARNING Keep fixture at least 5 0 ft 1 5m away from any flammable materials decorations pyrotechnics etc ELECTRICAL CONNECTIONS A qualified electrician should be used for all electrical connections and or installations ISP CAUTIONS For added protection mount the fixture in areas outside walking paths seating areas or in areas were unauthorized personnel might reach the fixture Ambient operating temperature range for this fixture is 14 to 113 F 10 to 45 C Do not use the fixture under or above this temperature Before mounting the fixture to any surface make sure the installation area can hold a minimum point load of 10 times the weight of the fixture 230 Ibs 104 kg Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing W A R N MINIMUM distance to lighted objects must be 16 5 feet 5m MAXIMUM temperature of external surface 194 F 90 C MINIMUM distance of inflammable materials from surface 1 6 feet 0 5m Keep fixture at least 4 9 feet 1 5m away from any flammable materials decorations pyrotechnics etc 18 RAYZOR BEAM 2R User Manual Ver 1
34. ode Slavei Slave2 Slave3 Slave setting Z Auto Program Master Alone Auto program Sound Control Master Alone Sound Control Current Time XXXX Hours Power on running time Total Run Time XXXX Hours Fixture running time Last Run Time XXXX Hours Fixture Last times clear Lamp Hours XXXX Hours Lamp running time Time Information Lamp Off Time XXXX Minute Lamp off time E LastRun Password Password XXX Timer Password 038 5 Clean Last Run ON OFF Clear Fixture Last time T LampTime Password Password XXX Lamp Password 038 Clean Lamp Time ON OFF Clear lamp time Temperature Info Head Temperature XXX F C 2 Wr e Software Version V1 1 4 Software version 5 Lamp On Off ON OFF Lamp on off Automatic On ON OFF Lamp on off Power on 9 Lamp On via DMX ON OFF Lamp on via DMX a Lamp Off via DMX ON OFF Lamp off via DMX E Max On at Temp 20 79 C 45 C 68 174 F 113 F Lamp restart at temp Lamp Off Temp 80 139 C 130 C 176 282 F 266 F Lamp off at temp Address Via DMX ON OFF Add via DMX No DMX Status Close Hold Auto Music Auto run if no DMX Pan Invert ON OFF Pan Reverse movement Tilt Invert ON OFF Tilt Reverse movement Status Settings Pan Degree 630 540 Pan Degree Select Feedback ON OFF Movement Feedback Movement Speed Speed 1 4 Movement Mode Select E Mic Sensitivity 0 99 Sensitivity of Mic Hibernation OFF 01M 99M 15M Stand by Mode o S Service Setting Password Password XXX Service Password 050 5 RDM PID XXXXXX RDM
35. re connected in a DMX line does not influence the DMX adaressing For example a fixture assigned a starting DMX address of 1 may be placed anywhere in the DMX chain at the beginning at the end or anywhere in the middle The DMX controller knows to send data assigned to address 1 to that fixture no matter where it is located in the DMX chain The RAYZOR BEAM 2R can be controlled via DMX 512 protocol and the DMX address is set via the control menu DATA CABLE DMX Cable REQUIREMENTS For DMX and Master Slave Operation Your fixture and your DMX controller require a standard 3pin or 5pin XLR connector for data input and data output see figure below If you are making your own cables be sure to use two conductor shielded digital DMX cable rated at 120 ohms this cable is designed for DMX transmission and may be purchased from your Elation dealer or at most professional lighting retailers Your cables should be made with a male and female XLR connector on either end of the cable Also remember that a DMX line must be daisy chained and cannot be split unless using an approved DMX splitter such as Elation s Opto Branch 4 Opto Branch 8 or DMX Branch 4 21 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com DMX Output DMX Input DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 5 Pin XLR Socket 5 Pin XLR Socket 1 Ground 1 Ground 2 Data e 2 Data 3 Data 3 Data 4 Open 5 Open Be
36. rranty INSTALLING OR REPLACING THE LAMP To ensure a proper safe lamp change carefully read all the following instructions LAMP PROTECTION CIRCUITRY Because of the nature of the extreme heat associated with the Phillips Platinum 2R lamp and the tight nature of the internal optical system it is IMPERATIVE that the lamp be replaced every 6 000 Hours This is done to protect the internal optical system as well as prevent accidental lamp explosion which could lead to hot glass particles falling from the fixture 057 At 6 000 Hours the LCD control display will begin to flash Replace The Lamp and FAILURE TO CHANGE THE LAMP WITHIN 300 HOUR of the 6 000 HOUR RATED LIFE WILL CAUSE THE FIXTURE TO AUTOMATICALLY SHUT DOWN the lamp will flicker for the first five minutes of operation At this point the lamp has reached the maximum rated life and should be replaced immediately After the lamp has flickered for about five minutes it should strike normally allowing the fixture to be used temporarily until a replacement lamp can be installed The fixture will continue to operate for an additional 300 hours however the Replace the Lamp warning will continue to flash in the display Keep in mind that the flicker protection circuitry will only work for about 300 Hours lamp clock life of 6 000 6 300 Hours After 6 300 Hours the fixture will no longer respond to DMX commands and immediately enter a hibernation mode that will elec
37. s ENTER to confirm Select Auto Program Press ENTER to confirm Select Master or Alone Press ENTER to confirm Press MODE ESC in order to return to the main menu 33 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com EDIT PROGRAM Record Controller Working With Built In Program continued 3 Program Selection for Auto Pro Part Select Edit Program Press ENTER to confirm Select Select Programs Press ENTER to confirm Select Auto Pro Part 1 Auto Pro Part 2 or Auto Pro Part 3 and select which Slave program is to be sent Selection Part 1 means that the Slave unit runs the same program as the master units Press ENTER to confirm Press MODE ESC in order to return to the main menu 4 Program Selection for Edit Program Select Edit Program Press ENTER to confirm Select Edit Program Press ENTER to confirm Select the desired program With this function you can edit specific scenes into a specific program Press ENTER to confirm Press MODE ESC in order to return to the main menu 5 Automatic Scene Recording Select Edit Program Press ENTER to confirm e Select Edit Scenes e Select desired scene numbers A maximum of 250 scenes can be programmed Press ENTER to confirm Press MODE ESC in order to return to the main menu 34 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com Example
38. sure to follow the above figure when making your own cables Do not use the ground lug on the XLR connector Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR outer casing Grounding the shield could cause a short circuit and erratic behavior DMX 512 CONTROLLER CONNECTION Connect the provided XLR cable to the female XLR output of your controller and the other side to the male XLR input of the RAYZOR BEAM 2R The diagram below illustrates a typical DMX 512 connection when the fixture is in the 16 Channel Extended Mode You can chain multiple panels together through serial linking The cable that should be used is two conductor shielded DMX cable with XLR input and output connectors Always be sure daisy chain your in and out data connections never split or Y your DMX connections unless you are using an approved DMX splitter such as Elation s Opto Branch 4 Opto Branch 8 or DMX Branch 4 Ld LJ DMX512 120 DMX controller Address 1 Address 17 Address 33 22 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com DMX 512 CONNECTION WITH DMX TERMINATOR A DMX terminator should be used in all DMX lines especially in longer runs The use of a terminator may avoid erratic behavior in your DMX line A terminator is a 120 ohm 1 4 watt resistor that is connected between pins 2 and 3 of a male XLR connector DATA and DATA
39. t always use mounting hardware that is no less than M10 x 25 mm also be sure the hardware is insert in the pre arranged screw holes in the bracket of the fixture Use the original packaging and materials to transport the fixture in for service DO NOT TOUCH the housing bare hand during its operation Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before replacing or serving 8 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com DISCHARGE LAMP WARNING This fixture is fitted with a DISCHARGE LAMP which is highly susceptible to damage if improperly handled NEVER touch the lamp with your bare hands as the oil from your hands will shorten the life of the lamp Also NEVER move the fixture until the lamp has had ample time to cool Lamps are NOT covered under warranty conditions Avoid switching the fixture ON and OFF repeatedly in short intervals as this will reduce lamp life and intensity To achieve the intensity associated with discharge lamps these lamps use gas sealed in a high pressure environment to emit a brilliant output eS Due to the high pressure involved with the construction of the lamp the lamp MAY EXPLODE DURING PROLONGED EXTENSIVE USE This risk is increased with age added care is encouraged when dealing with older lamps Thus the lamp must always be replaced at the end of their recommended duty cycle Extreme caution should be used when operating t
40. the DMX input jack of the fixture he DMX controller is switched off or defective he DMX cable or connector is defective A DMX terminator has been inserted into the last fixture in your DMX chain 24 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com FIXTURE MENU ON BOARD SYSTEM MENU The RAYZOR BEAM 2R comes with an easy to navigate system menu The next section will detail the functions of each command in the system menu LCD MENU CONTROL PANEL The control panel see image below located on back of the fixture allows you to access the main menu and make all necessary adjustments to the RAYZOR BEAM 2R During normal operation pressing MODE ESC button once will access the fixture s main menu Once in the main menu you can navigate through the different functions and access the sub menus with the UP DOWN RIGHT and LEFT buttons Once you reach a field that requires adjusting press the ENTER button to activate that field and use the UP and DOWN buttons to adjust the field Pressing the ENTER button once more will confirm your setting You may exit the main menu at any time without making any adjustments by pressing the MODE ESC button LATION RAYZOR 2R 990 CEQEV BO 25 RAYZOR BEAM 2R User Manual Ver 1 Evariop www elationlighting com Set Dmx Address 001 DMX address setting 6 Dmx Value DMX value display 9 Slave M
41. tronically discontinue all fixture functionality with the exception of a few menu commands The fixture will continue to enter hibernation mode until the lamp is replaced and the lamp clock has been reset To replace the lamp follow the safety guidelines and procedures listed on the next page 11 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com LAMP SAFETY INSTRUCTIONS ALWAYS replace lamp every 6 000 Hours Use only Genuine Original Phillips Platinum 2R lamps Other brand lamps may cause damage and void the warranty NEVER touch the lamp with your bare hands as the oil from your hands will shorten the life of the lamp Always disconnect the fixture s main power supply before replacing lamp Allow fixture to cool for at least 15 minutes before attempting any type of service Make sure ALL covers panels are replaced secured before operating the fixture to prevent any risk and or damage to eye retina from UV Radiation exposure LAMP INSTALLATION PROCEDURE 1 Place fixture on a flat surface and remove 3 screws marked A B and C then remove rear cover plate to access the lamp LAMP COVER PLATE LY A T 45 C T 90 C LAMP PLATINUM 2R CAUTION HOT LAMP Let the lamp cool down for 10 min Change the lamp by loosening screws A B C MUST BE replaced at 6 000 Hours pedem Genuine Original Philips platinum lamps Other brand lamps may cause damage VAN T and void warranty
42. unter is automatically reset after each time the lamp is powered ON INFORMATION Time Information LastRun Password Display the fixture timer password 038 INFORMATION Time Information Clear Last Run Resets the last run time of the fixture INFORMATION Time Information LampTime Password Displays the lamp timer password 038 INFORMATION Time Information Clear Lamp Time Resets the run time of the lamp INFORMATION Temperature Information Head Temperature Displays temperature of the fixture INFORMATION Software Version Displays software version of the fixture LAMP CONTROL Lamp ON OFF When ON manual control of lamp power can be accessed via system menu LAMP CONTROL Automatic ON When ON lamp is automatically powered ON when power is applied to fixture 28 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com LAMP CONTROL Lamp ON via DMX When ON lamp can be powered ON via a DMX controller LAMP CONTROL Lamp OFF via DMX When ON lamp can be powered OFF via a DMX controller LAMP CONTROL Max ON at Temp The fixture is designed to shut the lamp OFF when an excessive temperature is sensed inside the head by the on board CPU The lamp is shut OFF to prevent damage to the lamp and avoid possible internal damage to the fixture head This function sets the MIN internal operating temperature of the fixture head before the lamp will restrike after th
43. xture reset if the magnetic indexing circuit malfunctions sensor failed or magnet is missing Color Wheel Error or there is a stepper motor failure defective motor or defective motor IC drive on main PCB The Gobo Wheel 1 movement is not located in the default position after O6Er the reset This message will appear after a fixture reset if the magnetic indexing circuit malfunctions sensor failed or magnet is missing Fix Gobo Wheel Error or there is a stepper motor failure defective motor or defective motor IC drive on main PCB 41 RAYZOR BEAM 2R User Manual Ver 1 www elationlighting com CLEANING AND MAINTENANCE U T O N Disconnect power before cleaning or maintenance CLEANING Frequent cleaning is recommended to insure proper function optimized light output and an extended life The frequency of cleaning depends on the environment in which the fixture operates damp smoky or particularly dirty environments can cause greater accumulation of dirt on the fixture s optics Clean the external lens surface at least every 20 days with a soft cloth to avoid dirt debris accumulation e Never use alcohol solvents or ammonia based cleaners MAINTENANCE Regular inspections are recommended to insure proper function and extended life There are no user serviceable parts inside this fixture please refer all other service issues to an authorized Elation service technician Should
Download Pdf Manuals
Related Search