- Hoyt.com
Contents
1. ment marks you should take your bow to an author ized Hoyt dealer for adjustment prior to its next use String damage and poor arrow flight may result from shooting improperly tuned equipment Buss Cable Marks TUNING To tune your bow have on hand three fletched arrows and three bare shafts all identical and straight From about 15 to 20 yards shoot your fletched arrows making necessary sight adjustments to hit the target at the same spot each time Once you have sighted in shoot the three bare shafts and note where the group of bare shafts are compared to the fletched arrows If the bare shafts are grouping below the fletched arrows lower the nocking point See fig 14 If the bare 20 shafts are grouping above move the nock point up See fig 15 Be sure to only move in small increments never more than 1 16 at a time Each time the nock ing point is moved it will affect your sight setting so you will have to re set your sights after each move Continue to make adjustments until both groups are relatively close together If the bare shafts hit to the right of the fletched arrows decrease bow weight check for vane clearance or check arrow spine stiffness weak See fig 16 If the bare shafts group to the left increase bow weight check for vane clearance or check arrow spine stiffness stiff See fig 17 Some adjustments can be made slightly moving the arrow rest to the left of the right Note Left handed shooters n2. Compound Bow Owner sM anual SHoytusa GET SERIOUS TABLE OF CONTENTS 1 Bow Owners Personal Record 0 0 0 2 2 Compound Bow Terminology 3 3 Important Infomation 4 4 Compound Bow Maintenance Schedule Strings and Cables rrrnsnnrvorerrvovevvsrnrneveversrsrsennn 6 Bow LTC sn saa bidsesdeteteavereete 7 Bow Press WS iesisessccdivesssscievecs sine Haddi said ik sikk 7 5 Initial Compound Bow Setup Rest Selecto esineisiin 9 Nock Set Installation cccccccecssssseesseeeseeeeees 10 Cable Guard Installation eorrnroonvrrrnrrrnrnrnnnne 10 Tiller Adjustment seie isss kannar 13 Centers hobes oeeie he 14 Pletch Clearance sissccsssiesssvsssssssvarvecsassceessaseesensensves 15 6 Compound Bow Adjustment Draw Weight Adjustment e0ee e e e 15 Draw Length Adjustment snsenrnrvrvrrrerovorrrrnnn 16 Inner Cam Adjustments Two Cam 16 Optimizing CommandCam Performance 17 Inner Cam Adjustments One Cam 18 VersaCam Draw Length Adjustment 19 Aligning Dual Track Idler Wheel 19 7 Tuning Your Compound Bow sse08 20 8 Compound Bow Warrant 22 INTRODUCTION Welcome to the Hoyt USA family As a member of an elite team you will be pleased to know that you have purchased the finest crafted most dependable bow on the market Only the finest components go into every Hoyt USA bow
3. EVER DRY FIRE YOUR BOW Dry fire means to draw and release the bowstring with out an arrow Firing a bow without an arrow to absorb the energy can cause severe damage to your bow and possible injury to the shooter or others nearby 2 NEVER EXPOSE YOUR BOW TO EXTREME HEAT OR PROLONGED EXTREME DAMP Excessive heat such as that experienced on a sunny day inside a closed vehicle could cause limb failure Prolonged storage in a hot dry attic or damp basement could also be damaging 3 CAREFULLY INSPECT YOUR BOW BEFORE EACH USE Carefully note the condition of the bowstring limbs and riser before you shoot Frayed bowstrings should be replaced Damaged or suspect limbs should be reported to your local dealer for inspection or replacement 4 BE SURE OF YOUR BACKSTOP Make sure that the backstop you use is large enough to catch a stray arrow and that it is thick enough that the arrow cannot completely penetrate it Make sure that it is positioned in a safe direction away from dwellings and other people 5 BE SURE OF YOUR TARGET Make sure that there are no persons livestock buildings or other objects behind or near your target Be absolutely sure of your target in low light condi tions 6 INSPECT ALL ARROWS Before shooting inspect your arrows for defects Discard cracked or dented shafts Replace damaged or loose fletching and nocks 7 ALWAYS BE SAFE Never shoot straight up Be careful around strings and cables when u
4. MPOUND BOW SETUP REST SELECTION There are two basic types of arrow rests Shoot Through and Shoot Around See fig 3 Shoot through rests are designed for release shooters as arrows shot using a release bend vertically Shoot around rests are designed for finger shoot ers as arrows shot by fingers bend horizontally Hoyt USA recommends that you seek the advice of a qualified Pro Shop for the proper rest selec tion for your style of shooting fig 3 Shoot Through Shoot Around NOCK SET INSTALLATION A nock point is a reference on the string that marks the exact location for you to nock your arrow The arrow s nock is positioned under the nock set To install the nock set at the proper position begin by slipping the nock set on the string Then using your rest as a reference posi tion the nock set just above level A finger shoot er should initially position the nock set at approximately 3 8 above level The release shooter should begin at approximately 1 4 above level See fig 4 Once the nock set is at the desired location use a special set of nocking pli ers to crimp the nock set into place NEVER shoot a bow without a nock set or with a nock set that has not been properly crimped For proper installation Hoyt USA recommends that this be done by a qualified Pro Shop Hacking Point Height fig 4 CABLE GUARD INSTALLATION All aluminum Hoyt USA bows are designed with a built in cable g
5. along with over 70 years of experience in bow technology and manufactur ing With some basic maintenance your new bow should provide you with years of pleasure and dependable service Hoytis 543 North Neil Armstrong Road Salt Lake City Utah 84116 2887 801 363 2990 Phone 801 537 1470 Fax www hoytusa com BOW OWNER S PERSONAL RECORD Fill in the following Personal Bow Record for your later reference Bow Serial Number Hoyt USA Bow Model Purchased From Purchase Date Draw Length Draw Weight _____ Bowstring Length ___ Cables Length Control Cable Length Important Note Save your sales receipt That receipt is your proof of date of purchase Proof of date of purchase will be required should your bow ever need warranty serv ice The following space has been reserved for you to staple or tape your sales receipt for safe and conven ient keeping IMPORTANT Staple or tape your sales receipt here for safekeeping COMPOUND BOW TERMINOLOGY Axle Cam Idler Single Cam Buss Cables Limb Weight Adjustment Bolt Weight Locking Screw ls Cable Guard Bar Cable Guard Glide Limb Weight Adjustment Bolt av NG Weight Locking Screw Limb Pocket Limb Buss Cables WARNING YOU RE RESPONSIBLE FOR ARCHERY SAFETY Please read the following safety information Disregarding these rules may cause serious injury to yourself or property 1 N
6. cam alignment varies slightly with dif ferent limb and riser combinations Your bow was shipped new in the optimum postion If your buss cable lies outside the alignement marks we recom mend you take it to your nearest Hoyt dealer for adjustments 17 VERSACAM DRAW LENGTH ADJUSTMENT All VersaCams feature the patented InnerCam adjustable draw length module system and adjustable let off When adjusting the draw length on VersaCam bows both the module and draw stop peg must be adjusted When the module is rotated to its furthest position in the minus direction the module is in the A setting the shortest draw length position Rotating the module in the direction to the next hole available for the module screw is the B setting which will provide approximately 1 2 longer draw than the previous setting Eight modules are available for a total draw length range of 3 4 Draw Stop Peg VersaCam fig 14 Draw Length Screw Year 2002 Hoyt VersaCam draw stop holes are num bered 1 thru 8 on VC 2 amp VC 3 and 1 thru 7 on VC 1 Each InnerCam module position has a set of draw stop peg positions that will provide a useable range of effective let off values The table to the right provides the correct peg setting for 80 effective let off and 65 AMO let off for each InnerCam module position 18 VERSACAM CHART Measured as Effective let off which includes friction 65 AMO let off is required for entry of tro
7. del bows make sure that the longest slot is to the rear and the shorter slot is closest to the grip See fig 7 Note If you have trouble pulling the cables back far enough to get the glide over the end of the cable guard bar you will need to use a bow 12 press Hoyt USA recommends that the cable guard glide installation be done at a Pro Shop CAUTION Do not pull bow back without proper installation of cable guard bar and glide TILLER ADJUSTMENT Tiller is the difference in actual distance between the upper limb to the string and lower limb to the string measured from the base of the limbs where the limb and riser meet at a 90 degree angle See fig 8 Redline cam models must be measured from a reference line from axle to axle See fig 9 The main function of tiller is to allow the archer to more easily and comfortably aim during the draw and release of the shot Most bows will shoot best with an even tiller which means the distance from the string to the limb is the same on top and bot tom Tiller adjustments are made by adjusting either limb weight adjustment bolt See draw weight adjustment section pg 15 Example Too much tiller on the bottom limb decrease the weight on the top limb or increase the weight on the bottom Hoyt USA recommends that you ini tially set tiller equal top and bottom CENTERSHOT Centershot is the alignment of the arrow in the power path of the st
8. eed to reverse these instructions for left and right results Hoyt USA recom mends that you work closely with your local Pro Shop when tuning your bow to ensure best results fig 17 21 TUNING WITH BROADHEADS Most archers discover that they must make slight tun ing adjustments when switching from practice points to broadheads even at the same weight Broadheads create a dramatic aerodynamic change in arrow flight For this reason slight adjustments may need to be made in nocking point height rest position or bow weight to achieve desired broadhead flight HOYT USA COMPOUND BOW WARRANTY All Hoyt USA compound bows are warranted against defects in materials or workmanship to the original owner on aluminum risers limbs limb pockets and eccentrics for the life of the product ACCESSORIES All Hoyt USA sights excluding sight pins arrow rests and bow quivers excluding hood foam and arrow gripper are warranted 100 for the life of the product to the original owner Hoyt USA must per form warranty work You must have the following items in order to obtain warranty work 1 A dated proof of purchase sales receipt 2 Products must be purchased through a Hoyt USA authorized dealer no exceptions 3 All compound bows must have a serial number Hoyt USA at its discretion voids all warranty claims either expressed or implied including but not limited to evidence of abuse modification to original design 22 u
9. ing Screw DRAW LENGTH ADJUSTMENT INNERCAM ADJUSTABLE MODULES Many Hoyt bows utilize the patented InnerCam adjustable module for draw length adjustment The InnerCam can generally be adjusted without the aid of a bow press TWO CAM DRAW LENGTH ADJUSTMENT To adjust the draw length on Hoyt s two cam inner cam model bows use a standard allen key to loosen the fastening scre wand remove the Draw Length screw Rotating the inner cam in the direc tion will lengthen the draw Rotating the inner cam in the direction will shorten the draw Once the Draw Length fig 13 Inner Cam Fastening Screw inner cam is in the desired location reinstall and tighten the Draw Length screw first and then the Fastening Screw Each position will provide approxi mately 1 2 longer shorter draw than the previous setting Note You must make the same adjustments to the top and the bottom inner cams or the bow cannot be properly tuned OPTIMIZING COMMAND CAM PERFORMANCE In order to verify optimum performance of your Command Cam bow you should examine the cam s built in alignment marks When viewing the module side of the cam your bus cable ore lie somewhere between the alignment marks as shown It is not neces sary to have the buss cable exactly centered between the marks In fact the optimum Buss Cable Buss Cable position may be Yoke at either extreme side of the timing marks for your particular combi nation Exact
10. ot be liable for injury or property other than the bows themselves Hoyt USA reserves the right to replace defective parts according to availability with compatible replacement parts NOTES 24 NOTES WARRANTY REGISTRATION CARD Or register on line at www hoytusa com Bow Model Bow Serial Number Located in rest plate area Owner s Name Address City State Zip E Mail Address Place of purchase Date Age Gender M F How many years have you shot 0 5 5 10 10 Is this your first Hoyt bow YES NO How often do you purchase a new bow What type of archery do you participate in Bowhunting 3D FITA NFAA Traditional Will you hunt with this bow YES NO How many days a year do you hunt 0 10 10 20 20 What are the top three Species of animals you hunt OLLP8 LN NO aye YES peoy SUOISUITY ION YHON EFS YSN JOHA Hoytus GET SERIOUS 543 North Neil Armstrong Road Salt Lake City UT 84116 www hoytusa com
11. phies into the Pope r Young Record Book Remove the peg entirely on VersaCam 1 Moving the draw stop more than one position away from those shown in the chart is not recommended Note changing the draw stop position independent of the module to manipulate let off will alter draw length by approximately 3 16 for each draw stop hole draw length will be shortened when changing to a lower let off position and lengthened in higher let off positions Slight variations in peak weight up to two pounds may occur when changing the InnerCam position ALIGNING DUAL TRACK IDLER WHEEL To ensure your dual track idler is functioning within its intended rotational limit periodically check the idler s built in rotational alignment marks scribed on the wheel as shown in the Figure on the next page For right handed bows the alignment marks should be at the bottom of the idler on the side marked with an S 19 To check the idler position sight down the buss cable yoke and verify that it lies between the gl alignment marks on k aT F a H the idler It is not g 7 String critical where the i buss cable yoke lies 5 fr between the align Control Alignment ment marks but Cable simply that it is within the marks Left handed bows require the same examination except that their timing marks will lie on the bottom of the idler on the side marked with an L In the event that your buss cable yoke falls outside the align
12. ring This is accomplished by moving the arrow rest left or right Release shooters should line the arrow up with the power path of the string See fig 10 Finger shooters should position the arrow so that the tip is just to the outside of the power path of the string See fig 10 Centershot is critical to how accurate a bow will perform These are initial centershot settings for proper alignment Hoyt USA recommends this be done by a qualified Pro Shop 14 fig 10 Release Setting Fingers Setting FLETCH CLEARANCE Fletch clearance is the ability of your vanes or fletch ings to pass cleanly by or through your arrow rest without impacting the rest so severely that the arrows flight path is disrupted Itis necessary that you have adequate vane clearance to achieve proper arrow flight See fig 11 fig 11 Incorrect Correct COMPOUND BOW ADJUSTMENT DRAW WEIGHT ADJUSTMENT Weight adjustments can easily be made by turning the weight adjustment bolt clockwise to increase weight 15 fig 12 or counter clockwise to decrease O OD weight Note Always turn the top and bottom adjustment bolts of OK in equal amounts Some Hoyt USA model bows are equipped with a Dual Locking Pocket System Before draw weight adjustments are made on these models you must first loosen the Pocket Locking screws located on the side of the pocket See fig 12 When adjustments are completed re tighten the Pocket Locking screws Pocket Lock
13. se of attachments or accessories that cause excessive stress Hoyt USA reserves the right to make substitutions on warranty coverage at Hoyt USA s discretion for any reason Warranty is subject to available parts OBTAINING WARRANTY SERVICE To obtain warranty service you should return to the Pro Shop where you purchased your Hoyt USA bow The dealer can help to determine if Hoyt USA factory service is required or if the repair can be completed by the Pro Shop If the bow must be returned to the fac tory the bow owner is responsible for the return freight to Hoyt USA Hoyt USA in turn will pay for the same return freight of the repaired product Before any bow is returned a Return Authorization number must be obtained through an authorized Hoyt USA Pro Shop Bows returned to the factory without a Return Authorization number will be sent back Do not send accessories with bow unless other wise instructed to Hoyt USA bows requiring factory service should be sent to Hoyt USA 543 N Neil Armstrong Road Salt Lake City UT 84116 23 There are no other warranties expressed or implied that extend beyond those written here No agent employee or representative of Hoyt USA or its dealers has the authority to bind Hoyt USA to any agreement not herein stated Buyer agrees that the sole and exclusive remedies for breach on any warranty con cerning Hoyt USA bows shall be repair or replace ment of defective parts Hoyt USA shall n
14. sing broadheads Cutting strings and cables can cause serious damage to your bow and possible injury to you or others Children must be super vised by an adult 8 READ AND HEED ALL WARNINGS Hoyt USA cannot be held responsible for injuries suf fered or caused by misuse unsafe or improper arrow and bow combinations Hoyt USA can 5 not be held responsible for injuries sustained when using an altered or modified Hoyt USA bow WARNING This bow is a deadly weapon Always abide by all saftey advisements Children must be supervised by an adult COMPOUND BOW MAINTENANCE Your bow is a mechanical device and as such is subject to wear and need of periodic inspection adjustment and service Hoyt USA recommends that you take your bow to a Hoyt authorized pro shop at least once a year for a yearly profession al maintenance and inspection Areas to be inspected are axles spacers lubrication of axle bushings e clips strings cables limbs and riser The following information provides helpful instruction on the proper care and maintenance of your new Hoyt bow Keep this manual as a handy guide for future reference STRINGS AND CABLES Apply a light coat of bowstring wax to your bow s cables and string on a regular basis Hoyt USA suggests once every two weeks during peak use Use a high quality bowstring wax available at your local Hoyt Pro Shop 6 This will keep your bow s string and cables in good condition To assure bes
15. t results replace D 75 string and cables when wear is evident or every two years under normal use conditions Insist that Hoyt USA string and cables be used on your bow Beware of lesser quality string and cables as they may alter the performance of your bow or cause damage to it ECCENTRIC LUBRICATION A light spot lubrication of the axles where they pass through the eccentric should be done on a regular basis 1 500 2 000 shots In adverse hunting conditions where dirt dust or moisture are encountered lubrication may be done on a daily basis Hoyt USA recommends you use a silicone or Teflon based lubrication or any other quality grease available at your local Hoyt USA Pro Shop It is not recommended that you use Penetrating Oils such as WD 40 EZ 7 Fast Break etc BOW PRESS USE Never allow your bow to be put into a bow press unless it is operated by a knowledgeable bow technician Hoyt USA recommends that all nec essary adjustments requiring the use of a bow press be done by an authorized Hoyt Pro Shop fig 1 An Example of a Double Pull Bow Press Always use a double bow press like that shown in figure 1 when working on your bow Never use a single pull bow press See fig 2 fig 2 An Example of a Single Pull Bow Press 8 When putting your bow in a bow press never put pressure on the riser Always position the rollers at the base of the limbs where the limbs enter the limb pockets CO
16. uard bar attachment Before 10 mounting the cable guard bar you must remove the nylon screws used only for shipping purpos es To insert the cable guard bar simply slide the bar through the two mounting holes on the riser making sure that the bar is pushed completely through and flush with the end of the front Screws Flush w Front of Riser 30 Q mounting hole After the bar has been inserted fasten with the 1 4 20 x 1 2 set screws provid ed See fig 5 Hoyt USA s magnesium bows are designed with a high mount style cable guard bar that is mounted directly to the side of the riser by two 10 24 screws See fig 6 Prior to mounting the cable guard bar you must remove the nylon screws used 10 24 SHCS Screws fig 6 only for shipping purposes Warning On some shorter axle to axle models adjustable cable guard bars can be off set too much causing the cable to track off the cam This can cause dam age to the bow or personal injury To prevent this from happening NEVER SET THE BAR AT THE THREE O CLOCK POSITION CABLE GUARD GLIDE INSTALLATION Hoyt USA uses a specially designed cable glide that has off set cable slots To correctly install the glide on all Hoyt models except the Excel Cam make sure that when the cables are insert ed into the glide the shortest slot is to the rear and the longer slot closest to the grip For all P Excel Cam Glide Position fig 7 Excel Cam mo
Download Pdf Manuals
Related Search