USER MANUAL - Induo Wireless
Contents
1. RTS 13 gt CTS 6 SATEL C LINK 100 User Manual Version 1 0 3 FUNCTIONS Screw connector functions 3 1 Operational Voltage 9 30 Vdc e The Supply Voltage is connected to connectors 9 30 VDC and e OUTis internally connected to VDC through an internal fuse The supply Voltage for the Extension Units must be taken from the connector O UT 3 2 Alarm output AL OUT e The ALOUT is activated when 3 consecutive transmissions has been failed When activated the output state goesto VDC When a C LINK 100 sends information to another C LINK 100 it requires an acknowledgement message In case there is a fail in transmission and the C LINK does not receive an acknowledgement message the transmission will be retransmitted maximum 3 times or until an acknowledgementis received 3 3 OUT e A Voltage output to the extension units etc This line is internally connected to VDC through a fuse 3 4 Digital Inputs 11 14 and Outputs O 1 04 e Inputs o 4pcs Activated with voltage e Outputs o 4pcs O pen relay contacts Can be connected to any 0 250 VAC 2A load 3 5 Pulse Inputs FAST SLOW e Inputs o SLOW For slow pulses Maximum input frequency is 2 kHz Maximum number of the pulses in the memory 4 x 10 o FAST For fast pulses Maximum frequency is 10 kHz Maximum number of the pulses in the memory is 4 x 10 e Outputs o SLOW For slow pulses O utput frequency rate is 5Hz Relay outp2. General 1 3 extension modules can be connected to SATEL C LINK 100 The system functions both on Point to Point and Multipoint protocols At Point to Point protocol the respective extension modules operate as pairs according to their address setting The extension modules must always be connected to C LINK 100 control unit they do not operate alone I LINK 200 4 Digital and 2 Analogue inputs and outputs I LINK 300 6 Digital inputs and outputs Assembly The modules are joined together by connecting the EXTENSIO N and To EXTENSIO N connectors as in the picture The extension modules can be joined in any order The number of extension modules is 1 3 pcs C LINK 100 1 3 extension modules C LINK 100 Main module I LINK 200 Extension I LINK 300 Extension 4 Digital 4 Digital 2 Analogue 1 0 ports 2 Analogue I O ports 6 Digital I O ports z UO o Mm z ul Connections The 1 0 ports of the extension modules are connected same way as the main unit s I O ports The supply voltage is not linked through the modules so it must be connected using the green screw contacts The supply voltage must be connected directly to the C LINK 100 Asthe C LINK 100 is equipped with an internal Fuse self recovery type the extension must get the supply voltage from the connector O UT If there are many Extension modules the linking can be done what is the most practical for the wire work see the picture Settings Extension modules
3. 6 112 19 2 kbps Check that the radio modem baud rate is same as for C LINK and that other parameters are 9600 N 8 1 9600 bps is a default setting but can be changed to be any of the BAUD rates given above Set the message transmission interval by using TIM E PULSE switches as described above When both units have these basic settings TIM E PULSE can be different on both units the supply voltage can be connected Note Check that all ADDRESS switches are O FF when the C LINK 100 is used with any other than SATELLIN E 1870 radio modems 14 SATEL C LINK 100 User Manual Version 1 0 5 2 Point to Multipoint In this mode the Main Controller can drive one or more sub stations max 127 pcs 5 2 1Updates The updates are controlled by the Main Controller which sends messages to the sub stations or asks status information from them As the Main Controller is controlling the units the TIM E PULSE settings of the C LINK 100 are not valid There are two options on how to use the Point to Multipoint with the C LINK 100 1 The C LINK 100 protocol integrated to your own system 2 The system is controlled by the SATELLIN K PC or PC Pro software 5 3 Starting the Multipoint operation e Connectone SATELLIN E radio modem to the PC CO M Port This one will be the Main Controller e Connectthe C LINK 100 Sub station units to the SATELLIN E radio modems directly to C LINK 100 Radio Modem connector or using an interface cable e The
4. o Used atPoint to Point operation to selectthe divider factor for SLO W pulses This approach uses an electronic divider to adjustthe pulse rate A divider counts pulses and transmits one pulse when the preset divider factor is reached Settings for the Divider Factor o The Divider Factor can be set by the DIP switches 6 7 8 2 16 32 64 of the ADDRESS CHANNEL DIVIDER Lower row DIP switches 1 2 BAUD kb s The Baud Rate can be selected as follows 00 2 4 10 4 8 01 9 6 11 19 2 kbps 3 DE Alarm setting Immediate Delayed Alarm In case of a failure in the transmission the Alarm response can be selected from immediate Alarm to 10 minutes delayed Alarm 10 SATEL C LINK 100 User Manual Version 1 0 4 SM Safe Mode setting Unchanged state Safe Mode state In case a failure in transmission the outputs can be set to remain their status unchanged or change to Safe Mode which will switch all outputs to O FF position Safe Mode timing follows the setting of the switch 3 DE so itcan be immediate or delayed by 10 minutes The functions of the Dip switches 3 and 4 are set as follows 3DE 4SM 0 0 Immediate Alarm No Safe Mode 0 1 Immediate Alarm Immediate Safe Mode 1 0 Alarm delayed by 10 minutes No Safe Mode 1 1 Alarm delayed by 10 minutes Safe Mode delayed by 10 minutes 5 PT Pulse Time for selecting the transmission trigger 1 Pulse triggering 0 Time triggering 6 7 8 TIME F PULSE o Settings for Time
5. 010 50 pulses 0 1 0 5 pulses 011 100 pulses 0 1 1 10 pulses 100 500 pulses 100 20 pulses 101 1000 pulses 1 0 1 50 pulses 110 5000 pulses 1 1 0 100 pulses 111 10 000 pulses 1 1 1 Programmable by SATELLIN K PC Pro NOTE SLO W pulse divider is valid also for time triggering FAST pulse divider is valid only for pulse triggering 12 SATEL C LINK 100 User Manual Version 1 0 4 2 Pulse Outputs When the C LINK 100 unithas gota pulse message from the other C LINK 100 unit it ll send the pulses to its output The SLO W output speed is 5 Hz The FAST output speed is 10 kHz NO TE Due to the data rate between the radio modem and the C LINK 100 the maximum continuous transfer rate is limited to 2 Hz i e the incoming frequency must be the same or be less than the throughput of the two C LINK 100 units The maximum number of pulses P max for the preset time is calculated as follows Slow output P max T in seconds x Divider x 5 Examplel Time setting is 5 min Divider is 1 300 sec x1 x5 Pmax 1500 pulses Example2 Time setting is 5 min Divideris 10 300 sec x10 x5 Pmax 15 000 pulses Fast output P max T in seconds xDivider x 10 000 Example1 Time setting is 5 min Divider is 1 300 sec x 1 x10 000 Pmax 3 million Example2 Time setting is 5 min Divideris 10 300 secx10 x10 000 Pmax 30 million 13 SATEL C LINK 100 User Manual Version 1 0 5 OPERATION O peration mode is sel
6. EL C LINK 100 User Manual Version 1 0 2 SPECIFICATIONS FEATURE min max typical note Voltage 9 30 Vdc 24 Vdc typical Power consumption 0 03 0 1 VA Serial Interface RS 232 15 Vdc 6 Vdc active RS232 Extension Interface 0 3 6 Vde 0 5 5 Vdc active TTL Response time lt 250 ms lt 300 ms 9600 bps Operational temperature 25s 455 C Transfer rates 2400 19200 bps PULSE COUNTER Slow Inputs 1 pc max 2 kHz minimum pulse width l ms Fast Inputs 1 pc max 10 kHz minimum pulse width 5 us Slow Output max 5 Hz 50 50 pulse rate contact closure 1A 30 VDC Fast Output max 10 kHz 50 50 pulse rate Optoisolated 30 mA TRANSMISSION INTERVALS Time based continuous 7 days Pulse count based selectable DIGITAL SIGNALS Inputs 4pcs 0 30 Vdc 0 30 Vdc resistive 4 5 kO Outputs 4pcs 0 250 Vac 2A O 250 Vac 2A relay contacts INDICATORS Indicators Power ON OFF Digital Analogue IN OUT Alarm Pulse IN OUT OTHER OUTPUTS Alarm Output O 30 Vdc 30 mA 24 Vdc 20 mA active 30 mA GENERAL Casing Stainless steel Connectors D 15 for SATELLINE radio modem D 15 for extension module Size L x W x H and weight 123 x 85 x 30 mm 120g Mounting Wall plate or DIN rail IP IP 20 Modem compatibility SATELLINE 2ASxE 2ASc 3AS serie and SATELLINE 1870 C LINK 100 D 15 connector Radio Modem Direction Signal Pin VB DTR 1 14 15 GND SGND 7 8 gt RD 9 TD 11
7. ES amp SATEL USER MANUAL SATEL C LINK 100 Pulse Counter and l O converter SATEL C LINK 100 User Manual Version 1 0 TABLE OF CONTENTS TABLE DECO NTEN TS 2 E 2 IMPORTANT E tod dls e t 3 PRODUCTXAGONEORMEPIDS ss a EPOR RARO ove OVER EE E DO Ra ER ERE 4 WARRANTY AND SAFETY INSTRUCTIONS sesesesmmIHH mmm Rm ennenem ener 5 T GENERAL a ec 6 1 1 SATEL C LIN K 100 PULSE COUNTER AND I O CONVERTER nnm mmm 6 2 SPECIFICANO N fc heen nee aan 7 FUN E TONOS A eg PER 8 SCREW CONNECTOR FUNCTIONS cccecececececcecececeeeeececeneaeaeaeeneeeeeeaeaeaeaeneeeeeeeeatataeneneneenenentaeas 8 3 1 OPERATIONAL VOLTAGE 9 30 VDC oe ccccececccccccececeeeeeeeceaeaeaeaeeeeeeeeeataeataeneneeneneataeas 8 3 2 ALARM OUTPUT ALO UT ddr 8 3 30 EX Toc sed eios o s S A a o ET re 8 3 4 DIGITAL INPUTS 11 14 AND OUTPUTS O1 04 iuusssssesesenmm mme nens 8 3 5 SPHESETINPUTS RASTSEQW A ueri Exe ray Ganson i Sa ee Sins 8 dioc A e ea tun 8 Bel DIP SWITCHES vase a e TT 9 Jo LHowto ssetthe A ba o EL 10 4 SETTINGS FOR PULSES IN POINT TO POINT MODBDE nmm 12 Al A a ETA REE E EAEE EEA EEEE EE EAEE 12 4 1 1 Trigger settings Time and Pulse ooccccccccncnccccnnncnnoncncnncnnnnnnononcnnnnnnnnonnnnnonons 12 4 1 2 Inp t PUSIERA el ef ose 12 2 2 IS A SaN ee eects 13 5 OPERATIONS x ese the t Mu e e ed a 14 Salt POINT TO POINT ncnian od 14 5 1 1 Updating ME e als 14 5 1 2 Updating Pulse messages iiri iriir
8. PRTCL switch must be 1 P to MP e Before connecting the device to a power supply connect first all inputs and outputs that are to be used e Select the SATEL C LINK 100 BAUD rate 0022 4 102 4 8 012 9 6 112 19 2 kbps e Check that the radio modem baud rate is same as for C LINK and that other parameters are 9600 N 8 1 9600 bps is a default setting butcan be changed to be any of the BAUD rates given above e Set the individual addresses to all sub stations As this is a Main Controller lt gt sub station operation all Sub stations have to be addressed All sub stations must have different address e Open the Point to Multipoint program suitable for the SATEL C LINK 100 for example SATELLIN K PC or SATELLIN K PC Pro Please contact local SATEL distributor or visit SATEL s web site in order to get information of the multipoint commands 15 SATEL C LINK 100 User Manual Version 1 0 6 FACTORY SETTINGS The C LINK 100 I O converter is shipped with the following default settings unless specifically ordered with settings other than those listed below IXED SETTINGS DEFINED AT THE TIME OF ORDER PRTCL protocol switch P to P Point to point ADDRESS 0000000 No address 0 9600 bps 4 SM Safe Mode 0 Safe Mode O FF 5 PT Pulse Time 0 Time DE Alarm Delay 0 No delay TIME transmission interval 00 Continuous 16 7 CONNECTION EXAMPLES Point to M ultipoint Point to Point SATEL C LINK 100
9. User Manual Version 1 0 Point to Multipoint I Link PC I voc vy p ii ESI output is Opto isolated 17 Point to Point O utputs upper row screw contacts o DIGITAL O UTPUTS are open contact closures 2 A 12 24 DCV or 230 ACV o SLOW Pulse output is open closure as above The maximum output frequency is 5 Hz o FAST pulse output is opto isolated and needs to be connected to the VDC Inputs lower row screw contacts o 12 24 VDC Supply Voltage to pins o ALoutgoes high when an alarm is activated o OUT is Supply Voltage for Extension units etc o Digital inputs are activated with VDC High state threshold is 7 V 12 VDC Supply Power o SLO W Pulse input Activation Negative pulse edge Threshold 7 V 9 12 VDC Max input frequency 2 kHz Min pulse width 0 5 ms o FAST Pulse input Activation Negative pulse edge Threshold 7 VO 12 VDC Max input frequency 20 kHz Min pulse width 0 5 ms SATEL C LINK 100 User Manual Version 1 0 8 ACCESSORIES INTERFACE CABLES FOR CONNECTING SATEL C LINK 100 AND SATELLINE RADIO MO DEMS Point to Point CRS TSU C LINK 100 SATELLIN E 2ASc 2ASxE 3AS serie Point to Point CRS 18IF C LINK 100 SATELLIN E 1870 Point to Multipoint CRS 2F PC SATELLIN E 2ASc 2ASxE 3AS serie Point to M ultipoint CRS 18F PC SATELLIN E 1870 SATEL SATELLINK PC and SATELLINK PC Pro fo
10. based Point to Point transmission and divider for fast Pulse input o Time based setting defines the transmission interval The selected time interval is valid for both pulse counters o Pulse based setting defines the counted number of pulses when the transmission for Fast Pulses is triggered 11 SATEL C LINK 100 User Manual Version 1 0 4 SETTINGS FOR PULSES IN POINT TO POINT MODE The C LINK 100 has 2 different ways for handling the triggering of the pulse transmission in Point to Point mode The triggers are either Time or Pulse 4 1 Pulse Input 4 1 1 Trigger settings Time and Pulse Time triggering DIP switch 5 PT 0 DIP 678 Time 000 Continuous No time selected 001 2 sec 010 10 sec 011 1 min 100 1 hour 101 12 hours 110 24 hours 111 7 days When the preset time has been reached the C LINK unit sends a message to the other C LINK unit which starts to send out the pulses one by one The SLO W output speed is 5 Hz The FAST output speed is 10 kHz 4 1 2 Input Pulse divider Both inputs SLO W and FAST have their own Pulse Dividers for transmission triggering When the preset divider factor has been reached the C LINK unit sends one pulse to the other C LINK unit Pulse triggering DIP switch 5 PT 1 Settings for FAST pulses Settings for SLO W pulses Lower row Upper Row 678 Divider factor 163264 Divider factor 000 Direct 0 0 0 Direct 001 10 pulses 0 0 1 2 pulses
11. e channel the SL commands of the SATELLIN E 1870 must be ON N ote Point to Point Mode Check that all ADDRESS switches are O FF when the C LINK 100 is used with any other than SATELLIN E 1870 radio modems If any of the address DIP switches are O N it will notcause any harm butthe C LINK 100 will not operate SATEL C LINK 100 User Manual Version 1 0 3 7 1How to set the channel 878 SLOW PULSE When the power is turned ON the C LINK 100 reads the DIVIDE vl channel information from the ADDRESS switches 1 2 4 8 ee The default setting is 0 0 0 0 The channel is changed by turning first the power O FF selecting the channel and turning power O N The channel is selected from the DIP switches ADDRESS C HANN EL DIVIDER for example 1 0 0 0 12 ON up 0 0 FF down 00 E rt rado ites 1009 ADDRESS CHANNEL DIVIDER 1248 1248 Channel numbering 0001 chl 0010 ch2 0011 ch3 0100 ch4 0101 ch5 0110 ch6 0111 ch7 1000 ch8 10012ch9 1010 chl10 The channel must be same for both C LINK 100 units before turning the power ON When the power is turned O N the operational channel has been selected NO TE1 0000 disable This setting must be used if the radio modem does not support the channel select feature NO TE2 The C LINK 100 unit will not operate with the following settings 1011 1100 1101 1110 or 1111 The power O N indicator starts to blink in case any of these settings has been chosen 16 32 64 678 DIVIDER
12. ected by the PRTC L switch The operations are Point to Point or Point to Multipoint In Point to Point operation the system consists of one pair of units and the changes of the inputs at one end will be sent to the outputs on the other end In Multipoint mode the Main Controller commands one or more max 127 sub stations O peration mode is selected by the PRTC L switch The operations are Point to Point or Point to Multipoint In Point to Point operation the system consists of one pair of units and the changes of the inputs at one end will be sent to the outputs on the other end In Multipoint mode the Main Controller commands one or more max 127 sub stations 5 1 Point to Point Point to point operation is between two units The inputs of one C LINK 100 will be transferred to the outputs of the other C LINK 100 5 1 1Updating Digital messages Digital information relay switch etc will be sent to the other unit always when there is a change of a state atthe input 5 1 2Updating Pulse messages Pulse information will be sent according to the Time Pulse settings 5 1 3 Beginning with Point to Point operation Connect SATELLIN E modem to C LINK 100 directly to RADIO MO DEM connector or using an interface cable The PRTC L switch must be 0 P to P Before connecting the device to a power supply connect first all inputs and outputs that are to be used Select the SATEL C LINK 100 BAUD rate 0022 4 10 4 8 012 9
13. ia AA 14 5 1 3 Beginning with Point to Point OperatiON cccoocccoccncccnncncnconcncnonnnncnnononcnanonons 14 5 2 1 POINT TO M UETIPOTN Tz iier iaa A a ety ed EA T TANT 15 Balad WARES EE CK TEENE E E E AEA ES 15 5 3 STARTING THE MULTIPOINT OPERATION ccccecececcccecececececeeeeeaeaeaeneeeeeeeeaeataeaegeneenentatatas 15 o EACTORY SEITINGS So Et A CD OE AE EE dn 16 E CONNEC TON EXAMPLES ae 17 AECE ESO NES A AAA A AAA oe A AAA occa 18 9 EXTENSION MO DUES NRO 19 SATEL C LINK 100 User Manual Version 1 0 IMPORTANT NOTICE All rights to this manual are owned solely by SATEL O Y later called also SATEL All rights reserved The copying of this manual without the written permission from the owner of the rights by printing copying recording or by any other means or the full or partial translation of the manual to any other language including all programming languages using any electrical mechanical magnetic optical manual or other methods or devices is forbidden SATEL reserves the right to change the technical specifications or functions of its products or to discontinue the manufacture of any of its products or to discontinue the support of any of its products without any written announcement and urges its customers to ensure that the information at their disposal is valid SATEL software and programs are delivered as is The manufacturer does not grant any kind of warranty including guarantees on saleability and guarantees
14. ion 1 0 WARRANTY AND SAFETY INSTRUCTIONS Read these safety instructions carefully before using the product Warranty will be void if the productis used in any way which is in contradiction with the instructions given in this manual or if the housing of the radio modem has been opened or tampered with The radio modem is to be used only on frequencies allocated by local authorities and without exceeding the given maximum allowed output power ratings SATEL is not responsible if any products manufactured by it are used in unlawful ways The devices mentioned in this manual are to be used only according to the instructions described in this manual Faultless and safe operation of the devices can be guaranteed only if the transport storage operation and handling of the devices is appropriate This also applies to the maintenance of the products To prevent damage both the radio modem and any terminal devices must always be switched O FF before connecting or disconnecting the serial connection cable It should be ascertained that different devices used have the same ground potential Before connecting any power cables the output voltage of the power supply should be checked Salo Finland 2005 SATEL C LINK 100 User Manual Version 1 0 1 1 SATEL C LINK 100 Pulse Counter and I O converter The SATEL C LINK 100 is a Point to Point or Point to M ultipoint transparent pulse counter and 1 0 converter The device works together wi
15. pertaining to applicability to a certain application Under no circumstances is the manufacturer or the developer of a program responsible for any possible damages caused by the use of a program The names of the programs as well as all copyrights relating to the programs are the sole property of SATEL Any transfer licensing to a third party leasing renting transportation copying editing translating modifying into another programming language or reverse engineering for any intent is forbidden without the written consent of SATEL SATEL PRO DUCTS HAVE NOT BEEN DESIGNED INTENDED NOR INSPECTED TO BE USED IN ANY LIFE SUPPO RT RELATED DEVICE OR SYSTEM RELATED FUNCTION NORASA PART OF ANY OTHER CRITICAL SYSTEM AND ARE GRANTED NO FUNCTIONAL WARRANTY IF THEY ARE USED IN ANY OF THE APPLICATIONS MENTIO NED SATEL C LINK 100 User Manual Version 1 0 PRODUCT CONFORMITY SATEL C LINK 100 Hereby SATEL O y declares that the above mentioned productis in compliance with the essential requirements and other relevant provisions of Directive 89 336 EEC Therefore the equipment is labelled with the following C E marking 0523Q SATEL DECLARATION of CONFORMITY in Accordance with 89 336 EEC Directive of the European Council of 3 May 1989 on the approximation of the bows of the Member Stotes relating of electromagnet compatibility SATEL I LINK 100 200 300 SATEL C LINK SATEL MINI LINK SATEL C LINK 100 User Manual Vers
16. r Multipoint operation Complete programs that make it possible to operate a Multipoint system with a PC More information about program is available in the SATELLINK PC PC Pro Manual Layout of the SATELLINK PC Multipoint program Lm E eJ s a E RITE F e Config Window Hep x Digha Output Dipal input Digial Output r Dighalirpu DigtaiDupur Digital Input kone 1 TARKKAILU 1 D E digital output 1 Digital input 1 Digital output 1 Digital input 1 O KONEZ TARKKAILUS D Y vigitot output2 Digital input 2 O vigital output2 Digital Input 2 2 kowa TARKKAILI 3 e Digital outputs Digital Input a O Digital Output3 Digital Input 3 kone a TARKKAILU 4 D E Digital output 4 Digital input 4 Digital output 4 Digital input Analog Output 1 Analog Input 1 Analog Output 1 Analog Output 1 Analog Input 1 pP ts Rta Analog Input 1 snmmo quem arras nnn Analog Output 2 DIE Analog Output 2 y Analog Input 2 s Analog Input 2 Analog Input 2 KE 0 m C FA n C mae ema a AA Send Analog Dala MZ ay Send Manual 0u 00 00 Address 32 18 SATEL C LINK 100 User Manual Version 1 0 9 EXTENSION MODULES
17. th SATELLINE modems In Point to Point transmission a digital status information or count of pulses can be sent through the radio modem to be output in the other end Point to M ultipoint transmission is possible adopting software suitable for the SATEL C LINK 100 Upper row connectors 01 04 SLO W FAST O utput indicators ON O 1 04 SLO W FAST DIP Switches PRTCL Protocol ADDRESS C HAN NEL DIVIDER BAUD 3 DE 1 0N 0 0FF 4 SM 1 0N 0 0FF 5 PT 1 Pulse 0 Time 678 TIME F PULSE Input indicators ALARM 11 14 SLO W FAST Digital outputs Relay contacts Pulse O utputs SLO W 5 Hz contact closures FAST 10 kHz opto coupler Power O N O FF indicator Digital and Pulse outputs P to MP Point to M ultipoint P to P Point to Point Multipoint address Channel select Pulse divider Baud rate settings Alarm Delay Safe Mode Pulse Time Transmission Transmission interval for Pulses Pulse divider Indicator for failed transmission Digital and Pulse inputs Lower row connectors 9 30 VDC ALOUT J OUT I1 14 SLO W FAST D 15 connectors RADIO MO DEM EXTEN SIO N Supply Voltage Alarm output Common for Digital inputs and Extension Units Digital inputs Slow Pulse input max 100 Hz Fast Pulse input max 10 kHz Common Ground for Pulse inputs D 15 male for radio modem D 15 female for extension units Applicable only with SATELLIN E 1870 radio modems SAT
18. that are working as pairs in Point to Point operation must be same type and have same address The address is set by the Module Address switches The alternatives are 00 Module notin operation 01 10 and 11 Location is shown in the picture as Address 19
19. ut 1A 30 VDC o FAST For fast pulses O utput frequency rate is 10kHz O pen collector 30 mA 3 6 Indicators e ON o PowerO N OFF Illuminated when VCD is connected e 01 04 PO1 PO2 o Showing the status of the O utput Illuminated when output is activated SATEL C LINK 100 User Manual Version 1 0 e ALARM o Illuminated if a fail in transmission has occurred When the transmitting C LINK 100 sends information to another C LINK 100 it requires a confirmation to the sent messages In case there is a fail in transmission and the C LINK 100 did not receive a confirmation the transmission will be resend until a confirmation is received maximum 3 times 3 consecutive fails switches the Alarm LED ON e 1 14 PIL PI2 o Showing the status of the Input Illuminated when the input is activated 3 7 DIP Switches Upper row DIP switches 1 PRTCL Protocol switch o 1 P to MP for Point to M ultipoint M aster Slave operation o O P to P for Point to Point operation ADDRESS CHANNEL DIVIDER 1 2 4 8 16 32 64 ADDRESS o Forselecting address in the Point to M ultipoint operation o Example Ch 1 ON OFF OFF OFF OFF OFF OFF 1 2 4 8 16 32 64 Ch 5 ON OFF ON OFF OFF OFF OFF 1 2 4 8 16 32 64 o Maximum number of addresses is 127 1 2 4 8 CHANNEL works only together with SATELLIN E 1870 o Used atPoint to Point operation together with SATELLIN E 1870 radio modems to select an operation channel In order to change th
Download Pdf Manuals
Related Search