Home

Manual - Videcon

1. Panasonic WV CS850 860 960 TX400DC TX1000 TX1500 Vista MUX ENTRY EXIT dome menu 1 WASH 1 Goto Preset 25 SET select menu item W2 WIPE 2 w Goto Preset 26 ESC back to previous menu 3 AUTOPAN 3 Goto Preset 27 SPECIAL2 for special menus 4 LIGHTS 4 Goto Preset 28 The dome s internal PATROL can be LEARNED using the dome menu Setting the AUTO PAN KEY to PATROL will allow the patrol to be PLAYED by pressing AUTOPAN on the controller RX10X Dome Cable Description J6 1 J6 2 J6 3 Gnd J6 4 YELLOW DATA J6 5 GREEN DATA Options Functions Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity Option 3 A dome RESET ALL command can be sent by selecting option 3 and sending 4 twice with in 5 seconds This can only be done when not within the menu Care must be used with this command as the dome is set to default and user settings are erased Option 5 Vista receive mode Dome Switch settings The following procedure must be followed to ensure that the dome is set up correctly for terminated 4 wire RS485 at 19200 Baud and address 1 Remove the dome from its base before each step and reconnect to the base after changing the switches Step 1 Address switches 2 4 and 5 ON Step 2 Address switches 1 3 4 and 5 ON Step 3 Address switches 1 and 8 ON 4 Way switch 1 ON to select 4 wire terminated RS485 RX10X installation manual V1 05 14 Aug 10Page 20 Protocol 02 Pe
2. The dome and RX10X are linked using RS485 for control and video for the camera signal RX10X Dome Connection Description J6 1 J6 2 J6 3 Gnd J6 4 RS485B DATA J6 5 RS485A DATA Notes The dome address must be set at 1 for all the cameras that are controlled using a RX10X Check with the dome manual to enable the correct setup of the dome If the learned tour playback is running start patrol 1 is inhibited Options Function Option 1 Enable datum mode goto preset 1 after 5 minutes of inactivity Option 1 2 both on to start dome TOURZ2 instead of goto Preset 1 after 5 minutes if inactivity Option 3 reverses the pan direction The dome s TOUR2 must be programmed from within the domes menu Please refer to the dome manual for details RX10X installation manual V1 05 14 Aug 10Page 29 Trouble shooting quide Symptom No video from interface Possible causes Camera is not powered or not connected to Video from camera BNC on interface Check power and cabling Interface is not powered Check power Video out not connected to Video to controller BNC on interface Check cabling If the after following the above check list video still not present then remove both BNCs from the interface and connect together using a female female barrel connector to check video path from camera to control point Symptom No camera control but data out LED lights when the joystick is moved Possible causes Dome data cable
3. Do not expose the internal electronics of this unit to water or dampness for example in an unprotected outdoor installation or in any area classified as a wet location Accessories Do not attach this unit to an unstable stand bracket or mount The unit may fall causing serious injury to a person and serious damage to the unit Power sources This unit should be operated only from the type of power source indicated on the manufacturer s label If you are not sure of the type of power supply you intend to use consult your eguipment dealer or local power company For units intended to operate from battery power or other sources refer to operating instructions Power connector This unit is eguipped with coaxial power connector mounted at the edge of the PCB for low voltage power input Do not attempt to alter this connector in any way Power cord protection Power supply cords should be routed so that they are not likely to be trapped pinched or otherwise damaged by items in close proximity to them whether inside the unit or outside it Particular attention should be paid to cords at plugs connection units and the point of exit from the unit Overloading Do not overload outlets and extension cords as this can result in fire or electric shock Object and liguid entry Never push objects of any kind into the unit as they may touch dangerous voltage points or short out parts that could result in fire or electric shock Never spill liguid
4. Safety during installation or servicing Particular care should be taken to isolate the dome in order to prevent operation while engineering work is being carried out on the RX10X Adhere to safety standards All normal safety precautions as laid down by British Standards and the Health and Safety at Work Act should be observed WARNING TO PREVENT DANGER OF FIRE OR SHOCK DO NOT EXPOSE THE INTERNAL COMPONENTS OF THIS EQUIPMENT TO RAIN OR MOISTURE RX10X installation manual V1 05 14 Aug 10 Page 4 2 INTRODUCTION GENERAL The RX10X telemetry interface is designed to allow control of a variety of integrated dome cameras using BBV s range of up the coax telemetry transmitters See appendix A for a complete list of supported domes RX10X TECHNICAL SPECIFICATION Power Requirements Current Consumption Features Engineering Facilities Telemetry Signals Video Input Video Output Presets Dimensions Weight Temperature range 12 36VDC 24VAC from the dome supply excluding the Dennard dome This unit is supplied with a 2 1mm Jack power fly lead In addition a PSU 3 12V 1A in line PSU can be ordered from BBV 100mA maximum 12VDC e Two PCB construction Serial data output 2 wire RS232 422 485 Up to 16 preset positions can be stored within the RX10X Unit auto tunes to the coaxial telemetry signal 7 Segment LED readout for continual system status Data out LED Video launch amplifier provided
5. 3 RS485 control of dome Data rate 9600 Baud No parity 8 Data bits 1 Stop bits Connection details RX10X Dome Connection Description J6 1 J6 2 J6 3 Gnd J6 4 RX DATA J6 5 RX DATA Notes Check with the DM multiplexer manual for exact procedure for entering commands Dome settings Select dome address 1 P MODE PROTOCOL and 9600 N 8 1 Options Function Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity Option 2 is used to select the function that is used to drive the Esprit AUX outputs Option 3 is used to send a goto preset 95 or a save preset 95 when 1 is sent to the Rx10X OFF sends a save preset 95 ON sends a goto preset 95 Option 5 Vista receive mode Function OFF ON Esprit AUX No LIGHTS 1 2 WIPER 2 1 WASHER 3 3 RX10X installation manual V1 05 14 Aug 10Page 22 Protocol 13 Philips AutoDome including G3A and G3B RS232 RS485 control only not Bi Phase compatible Variable speed Pan Tilt Zoom Focus Auto focus 16 full scene presets 2 preset patrols Dome AutoPlay record amp playback Preshot title Zone title Menu Access Philips protocol TX400DC TX1000 TX1500 Display Menu Aux 46 1 WASH 1 Program Zone Title Aux 63 2 WIPE 2r Record AutoPlay start stop Aux 100 3 AUTOPAN 3 RESET DOME Set 899 4 LIGHTS 44 RS232 8 RS485 control of dome Data rate 9600 Baud No parity 8 Data bits 1
6. Gnd gwy Video to lt 250m RG59 20mA IN my Controller lt 500m CT125 20mA IN 12VDC 100mA Fig 6 20mA Control i A j p i 4 T E 5 i wa SA EE Tr Pelco Domes Pelco Esprit Has il Vista Powerdome Sensormatic y e pe e y a Y da I d I All Dennard Domes Bosch Domes JVC TX C676 Panasonic I I TxA 300Ohm closed resistance RX10X installation manual V1 05 14 Aug 10 Page 13 RX10X in test mode Fig7 test mode Rx100 TEST P2_V10 BBV CHECKING EEPROM WAIT EE OK P 0 T 0 Z FA 1111 1 ON 1 OFF P 0 TDO Z F l 1111 P 0 TD1 Z F l 1111 P 0 TA Z FA 1111 P 0 1 0 Z FA 1111 PLO T 0 Z F I 1111 PL2 T 0 Z F l 1111 Laptop computer Data bits 8 Stop bits 1 P 0 T O Z F I 1111 1 ON 1 OFF 2 ON 2 OFF P 0 TDO Z F I 1111 P 0 TD1 Z F l 1111 P 0 T 1 Z F l 1111 P 0 T O Z F l 1111 PLO T 0 Z F I 1111 PL2 T 0 Z F l 1111 Parity None Flow control None You will need to set up a HyperTerminal session on your laptop PC With the following settings Bits per second 38400 Once powered up the RX10X It will display the following Rx10X TEST V c 2009 BBV lt No Pan Tilt Zoom Focus Iris Alarms open lt 1 pressed lt and released lt 2 pressed lt and released lt Tilting Down at speed 0 lt Tilting Down at speed 1 lt stopped tilting lt No Pan Tilt Zoom Focus Iris Alarms ope
7. Goto Preset 28 A dome reset sets the camera as follows Shutter to 1 50 sec Backlight comp off AGC to 20dB The dome will display any change of Shutter Speed Backlight or AGC for a short period RS485 control of dome using the following connections Notes Camera switch settings MACHINE ID set both rotary switches to 0 8 way DIL switch all OFF apart from 8 which should be ON to enable the RS485 termination point to point simplex On screen display of preset position P01 P16 or MANUAL during manual control The on screen display can be enabled disabled using dome switch SW3 ON Display off OFF Display on Options Function Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity Option 2 Will perform a slow patrol between programmed presets when AUTOPAN pressed Option 3 on to allow the ExDR and MONO mode status to be displayed Have this off if you are programming a dome camera title and do not want to display the ExDR and MONO status Option 4 TK C675B mode Option 5 Vista receive mode DOME MENU Pressing 1 twice will display the dome s menu The joystick is then used to navigate through the dome menu 2 sends a SET command to the dome and 1 twice whilst the menu is displayed sends a BACK command If the 1 command doesn t work press a focus key before sending 1 Pressing 1 FOUR times within 2 seconds will display the dome s service menu RX10X installation manual V1 05 14 Au
8. IN Data In RS422 IN Data In Accessing the dome menus Press either 1 WASH 1 or Goto Preset 25 when in Vista mode to Enter Menu Pan Tilt zoom focus functions are then used to navigate through menu structure Please refer to individual dome manual for exact operation of menu Save User defined pattern Press either 2 WIPE 2 F or Goto Preset 26 when in Vista mode to start recording user defined pattern Then use Pan Tilt amp zoom functions to make the pattern you require then press either 2 FFWIPE 2 or Goto Preset 26 when in Vista Gnd DATA DATA mode to stop the recording of the user defined pattern IMPORTANT Dome settings Select dome address 01 or 001 Communications must be 4800 N 8 2 RS422 NOT SensorNet The interface software is based on 1997 protocol and has been tested with Ultradome IV Ultradome VI and original Speeddome Options Function Description Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity Option 1 2 both on to start preset patrol after 5 minutes if inactivity Option 5 Vista receive mode RX10X installation manual V1 05 14 Aug 10Page 24 Protocol 03 VCL Microsphere Orbiter range Variable speed Pan Tilt Zoom Focus Auto focus following a Zoom In Out 16 Full scene presets 2 preset patrols Slow preset tour Started by pressing AUTOPAN Program up to 16 privacy zones Vista up the coax Option 5 Ad
9. of any kind on or inside the unit Servicing Servicing of the unit should only be undertaken by gualified service personnel as opening or removing covers may expose you to dangerous voltages or other hazards RX10X installation manual V1 05 14 Aug 10 Page 3 Damage requiring service Servicing by qualified personnel should be carried out under the following conditions a When the power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the unit c If the internal electronics of the unit have been exposed to rain or water If the unit does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to normal operation e If the unit has been dropped or the enclosure is damaged f If the unit exhibits a distinct change in performance This indicates a need for service Replacement parts lf replacement parts are required ensure that only replacement parts recommended by the product manufacturer are used Safety check Upon completion of any service or repairs to the unit safety checks should be performed to ensure that the unit is in proper operating condition Pre installation checks lt is recommended that the unit be bench tested prior to installation on the site
10. 3 Test Buttons SW1 Makes the dome Pan Left SW3 Makes the dome Pan Right VIDEO LAUNCH AMPLIFIER AND CABLE LENGTH COMPENSATION The interface features a video launch amplifier with two variable controls situated close to the BNC connectors Lift and Gain These are pre adjusted for a cable distance of 500m of CT125 and are adjustable to compensate for video detail or signal losses if and when longer or shorter cable lengths are used to connect the telemetry transmitter to the interface Fig 4 Launch Amplifier The purpose of each control is Video from Dome GAIN varies the overall signal level LIFT boosts the high frequency component of the video Video to Controller signal If the high frequency component is too low picture appears washed out and lacking detail Default position adjusted for 500M of CT125 For shorter cable lengths turn the GAIN control anti clockwise until 1V p p is present at the telemetry transmitter For longer cable lengths turn the GAIN control clockwise until 1V p p is present at the telemetry transmitter RX10X installation manual V1 05 14 Aug 10 Page 12 1 SYSTEM SCHEMATIC DIAGRAMS Fig 5 COAX Control Q Ys Uu Pelco Domes Pelco Esprit al Vista Powerdome Sensormatic 2 pez E p I ha i mif f i w v i I J l 1 All Dennard Domes Bosch Domes JVC TX C676 Panasonic Videcon i I i Video from 1 TxA u Dome a T B
11. 6 privacy zones 100 115 The same procedure that is used to program a preset position is used to program or clear a privacy zone To instruct the RX10X to program privacy zoon zoom until the object you wish to mask fill the entire screen then press 2 followed by program preset 1 16 The screen will then go blank showing that the privacy zone has been set Clearing a zone To clear delete privacy zone press 3 followed by program preset 1 16 The relevant privacy zone will then be disabled Mono Colour switching If manual mono colour switching is required then option 2 must be OFF This will disable the privacy zone set clear features RX10X installation manual V1 05 14 Aug 10Page 25 Protocol 04 Surveyor Range SVFT S10 Variable speed Pan Tilt Zoom Focus Auto focus with manual override 16 full scene presets additional presets available using dome s menu 2 preset patrols Additional commands RUN TOUR 80 Pressing the AUTOPAN key will start the dome s Tour 80 The tour is programmable using the dome s menu and allows a complex preset patrol autopan or auto tour to be programmed Refer to the dome programming manual for exact details Vicon Dome TX400DC TX1000 TX1500 Dome Menu Store preset 94 Wm yn gp also AP once in menu o WASH 1 Al used as escape in menu 2 WIPE 2 AUX1 3 AUTOPAN 3 AUX2 4 LIGHTS A R RS485 control of dome using the following con
12. 870 Dome TX400DC TX1000 TX1500 DOME Menu preset 95 1 WASH 1 Call SWING preset 141 2 WIPE 2 Call GROUP1 preset 151 PS f AUTOPAN 3 Call GROUP2 preset 152 4 LIGHTS 44 Pattern Tour 1 playback press AUTOPAN preset 131 The dome and RX10X are linked using RS485 for control and video for the camera signal RX10X Dome Connection Description J6 1 J6 2 J6 3 Gnd J6 4 TX B DATA J6 5 TX A DATA Notes The dome switches must be as follows Dome Address 1 ON 2 7 OFF Address 1 Options Function Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity Option 2 Selection of baud rate OFF Pelco D 2400 baud Protocol and Baud 1 5 OFF 6 ON ON Pelco D 9600 baud Protocol and Baud 1 4 6 ON 2 38 5 OFF When navigating the dome s menu or privacy setup use the joystick and FOCUS NEAR and FOCUS FAR The dome manual has detailed information on the menu structure and privacy setting RX10X installation manual V1 05 14 Aug 10Page 28 Protocol 12 Vista Power Dome E Variable speed Pan Tilt Zoom Focus Focus lris Override returning to auto after Zoom In Out 16 Full scene presets 2 preset patrols PATROL1 RX10X patrol and PATROL 2 dome s TOUR Learned tour playback using AUTOPAN key Program up to 16 privacy zones Vista Power Dome TX400DC TX1000 TX1500 Display MENU 1 WASH 1 ENTER in MENU 2 WIPE 2 ESC in MENU 3 AUTOPAN 3
13. Call SWING preset 131 W2 WIPE 2 Run SWING 1 preset 141 3 AUTOPAN 3 Call GROUP1 preset 151 4 LIGHTS 4 Pattern Tour 1 playback press AUTOPAN preset 131 The dome and RX10X are linked using RS485 for control and video for the camera signal RX10X Dome Connection Description J6 1 J6 2 J6 3 Gnd J6 4 TX B DATA J6 5 TX A DATA Notes Dome Address 1 ON 2 8 OFF Address 1 1 Baud Rate 1 3 OFF Pelco D 2400 2 Termination 4 ON RS485 Termination On 3 Options Function Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity RX10X installation manual V1 05 14 Aug 10Page 17 Protocol 11 JVC TK C655B 675B TK C675E TK C675BE amp 676 Variable speed Pan Tilt Zoom Focus Auto focus can be enabled disabled from the dome menu 16 Full scene presets 2 preset patrols Slow patrol or dome autopan from controller AUTOPAN key Vista up the coax Option 5 TK C676 TX400DC TX1000 TX1500 Vista Mux OPEN MENU and BACK Twice 1 WASH 1 Goto Preset 25 x2 SET 2 WIPE 2 Goto Preset 26 Toggle ExDR 3 AUTOPAN 3 Goto Preset 27 Cycle Mono Mode 4 FLIGHTS 4 Goto Preset 28 TK C675B Option 4 TX400DC TX1000 TX1500 Vista Mux SHUTTER SPEED 1 WASH 1 Goto Preset 25 x2 BACKLIGHT AREAS 2 WIPE 2 Goto Preset 26 AGC 0 12 20dB 3 AUTOPAN 3 Goto Preset 27 DOME RESET 4 LIGHTS 4
14. F OFF ON OFF 18 ON OFF OFF ON ON 19 ON OFF ON OFF OFF 20 ON OFF ON OFF ON 21 ON OFF ON ON OFF 22 ON OFF ON ON ON 23 ON ON OFF OFF OFF 24 ON ON OFF OFF ON 25 ON ON OFF ON OFF 26 ON ON OFF ON ON 27 ON ON ON OFF OFF 28 ON ON ON OFF ON 29 ON ON ON ON OFF 30 ON ON ON ON ON 31 RX10X installation manual V1 05 14 Aug 10 Page 11 DIAGNOSTIC AIDS A 7 segment LED display is mounted on the top PCB this gives system status information The meanings of the values are as follows The value Description The value Description All OK Flashing red dot 9 0 No Video Sending a pan left to the dome 9 1 No telemetry carrier detected r Sending a pan right to the dome 9 2 No coax start bit detected u Sending a tilt up to the dome 9 3 Coax parity error d Sending a down up to the dome 9 4 No coax stop bit detected or frame error 9 5 Twisted pair parity error 9 6 Twisted pair over run error During the operation of the unit you will see a red flashing dot in the middle of the 7 segment LED display this means the unit is working The RX10X is designed to auto tune and compensate for any discrepancies in the transmitted telemetry signal there are no further adjustments that need to be made The RX10X has an in built facility that enables you to test the communications between the RX10X amp the dome This is done by pressing SW1 and the dome will pan left or press SW3 and the dome will pan right on releasing the button the dome will stop Fig
15. Stop bits Connection details RX10X Dome Connection Description RS232 RS485 J6 1 J6 2 J6 3 Gnd Gnd J6 4 RxD TxD DATA J6 5 Not Used RxD DATA Notes Options Function Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity Option 3 OFF preset title text is programmed following a save preset command by automatically issuing an aux 62 command ON the preset text command is not sent and the existing text is retained The dome must be RS232 controllable BI PHASE domes cannot be controlled Dome settings Select dome address 0 or 1 Communications must be 9600 N 8 1 The G3 Basic address is software programmable however as default the dome is addressed as 0 If the dome address is not 0 or 1 then the dome will require reprogramming using a Philips controller or turn on option 2 RX10X installation manual V1 05 14 Aug 10Page 23 Protocol 07 Sensormatic Ultra Dome 5 6 amp 7 Variable speed Pan Tilt Zoom Focus Auto focus Iris Open Close 7 full scene presets 2 preset patrols Pattern 1 define play using Autopan key Vista up the coax Option 5 Sensormatic Speeddome TX400DC TX1000 TX1500 Vista Mux Dome menu 1 WASH 1 Goto Preset 25 Start Stop Pattern 1 Definition 2 WIPE 2 Goto Preset 26 RS485 control of dome 4800 Baud No parity 8 data bits 2 stop bits RX10X Dome Connection J6 1 J6 2 J6 3 J6 4 J6 5 Notes RS422
16. Ua RX10X Multi Protocol Dome Interface Receiver Installation Guide Fal r beem Building Block Video Ltd 17 Apex Park ig i Diplocks Industrial Estate y i a i A Hailsham East Sussex BN27 3JU UK Tel 44 0 1323 842727 Fax 44 0 1323 842728 B B Support 44 0 1323 444600 www bbvcctv com TABLE OF CONTENTS 1 Pre installation Checks and Safety Procedures Unpacking Important safety precautions 2 Introduction General RX10X Technical specification Transmitter compatibility chart Cable connection method Fig 1 Cable connection method Cable types 3 Installation RX10X connections Fig 2 RX10X pcb connections 4 Setup Protocol select Protocol Selection Table Options amp Modes Option amp Mode Selection Table Diagnostic aids Fig 4 Test buttons Cable length compensation Fig 4 Launch amplifier 5 System schematic diagrams Fig 5 COAX Control Fig 6 20mA Control RX10X in PC TEST MODE Fig7 test mode 6 Dome specific information Dennard 2040 2050 2055 amp 2060 GENIE ASD276 amp ASD376 JVC TK C655B 675B TK C675E TK C675BE amp 676 Panasonic WV CSR400 WV CSR600 amp WV CSR650 Panasonic WV CVS 850 amp WV CVS 960 Pelco Spectra amp Esprit D protocol 2400 Pelco Spectra amp Esprit P protocol 9600 Philips Auto Dome RS232 485 Sensormatic Ultra Dome 5 6 amp 7 RS422 Only VCL Microsphere Obiter range Vicon Surveyor Range SVFT amp S10 Videco
17. ctor dB 100m at 5Mz Solid core Black 53 pF metre 6 2mm lt 2 1 RG59 Polythene Plain copper gt 90 coverage PVC UV 750 10 pra Han a 0 58mm nominal nominal dB 100m COAX resistant a 0 15mm x 64 Braid BARE Black CT125 a aa COPPER CU FOIL PVC UV 750210 pinte 9 8mm a COAX i Spaced COVERAGE 55 resistant nominal p PITCH 65 80 All cables contain a screen comprising of an aluminum tape with a backing that CW1308 Solid core NA ensures adhesion to the bedding PVC ee a 5 2mm TWISTED PAIR 0 50mm Moisture Barrier The tape screen is mtrs Z nominal applied in contact with a 0 80mm tinned Max copper drain wire RX10X installation manual V1 05 14 Aug 10 Page 7 3 INSTALLATION The RX10X requires all connections to the PCB to be made by the installer via terminal blocks or by plug and socket These connections are power in video in video out and serial data to dome See Fig 2 below for correct connections Fig 2 Iss2 PCB connections J5 0 Data out LED o o e GAIN z on Q Video from my Dome O 0 of Baran q U BBV PcsBoso009 TxA 000 BE gg TXB E a Video to Ha 00000000 Controller paa as 20mA IN cd 3 20mA IN 4 E 12VDC J3 100mA vw bbvcctv com Function Connector PCB Type Power in J2 Bottom 2 1mm coaxial Video in J3 Bottom BNC SOCKET Video out J5 Bottom BNC SOCKET 20mA Twisted Pair Telemetry in J6 Pins 1 amp 2 Bottom G
18. ditional commands AUTOPAN Pressing the AUTOPAN key will run the domes preset tour at slow speed between the patrol 1 preset position VCL Dome TX400DC TX1000 TX1500 Vista Mux 180 degree pan flip 1 WASH 1 Goto Preset 25 Privacy SET Toggle Mono Colour W2 WIPE 2 Goto Preset 26 Privacy CLEAR Auto Mono Colour 3 AUTOPAN 3 Goto Preset 27 Reset dome parameters 4 LIGHTS 4 Goto Preset 28 The dome and RX10X are linked using RS485 for control and video for the camera signal RX10X Dome Connection Description J6 1 J6 2 J6 3 Gnd J6 4 D DATA J6 5 D DATA Notes The dome address must be set at 1 for all the cameras that are controlled using a RX10X With an Orbiter Gold set the address to 1 with all switches of DILSW2 ON Select VCL protocol with all switches of DILSW1 OFF Check with the dome manual if you have any doubts If the slow preset tour is running start patrol 1 amp 2 is inhibited A manual goto preset and lens control will stop the tour leaving the AUTOPAN led on until the next manual pan command Options Function Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity Privacy zone programming Option 2 must be ON to allow programming of privacy zones _ The keystrokes shown assume use of a TX1500 Use the keystroke shown above if using another controller Option 5 Vista receive mode Programming a zone The RX10X can be used to program 1
19. g 10Page 18 Protocol 09 Panasonic WV CSR400 series WV CSR600 series WV CSR650 series Variable speed Pan Tilt Zoom Focus Auto focus Iris Open Close Auto focus with 600 amp 650 series 16 full scene presets 600 amp 650 series dome 2 preset patrols 600 amp 650 series dome Autopan 600 amp 650 series dome WV CSR400 WV CSR600 amp WV CSR650 TX400DC TX1000 TX1500 ENTRY EXIT dome menu 1 WASH 1 SET select menu item 2 WIPE 2 ESC back to previous menu 3 AUTOPAN 3 SPECIAL2 for special menus 4 LIGHTS 4 Autopan is started by selecting Autopan on the Transmitter The Autopan stops can be programmed from within the dome menu Please refer to dome user manual for exact details RX10X Dome Cable Description J6 1 J6 2 J6 3 Gnd J6 4 YELLOW DATA J65 GREEN DATA Notes IMPORTANT Dome settings Select dome address 01 Communications must be 19200 N 8 1 Ifdome cannot be controlled see dome manual section to reset dome to factory default Options Function Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity RX10X installation manual V1 05 14 Aug 10Page 19 Protocol 10 J Panasonic WV CVS 850 amp WV CVS 960 Variable speed Pan Tilt Zoom Focus Auto focus Iris Open Close Hold for auto iris 16 full scene presets 2 preset patrols Autopan Patrol learn play using autopan key Vista up the coax Option 5
20. he 3 year warranty o ged he Ai dy pad ian E MA to I6 Merman HEE 4 Registering for the new longer 3 year warranty term is quick has go camel rie farma Bodrac and easy Either Complete the warranty application card that comes in the box with your BBV product and return it FREEPOST to BBV BBV 3 Year Warranty If this card is returned with the serial number of the product and the Installation company details BBV will extend the warranty period from 12 Months to 36 Months Number of Units Start Serial No Final Serial No Contact Name Company Name Please could you send me information didas especially on ite Name Rx100s pad O Rx45x amp Rx55x et FBM Video Matrices Ped Tx1500 Video Matrices nies cres Starcard amp Starcard Converters ae BBV Quad Do you read Mme SO E ATA F Pick A Point I do not require any other further product information Please refer to WWW BBVCCTV COM for terms conditions amp exclusions VAT Reg No 621758439 Registered in England No 2852921 Registered office 17 Apex Park Diplocks Way Hailsham East Sussex UK BN27 3JU Or alternatively Register online at www bbvcctv com Simply enter your details on the Warranty Cover page Building Block Video Ltd Tel 44 0 1323 842727 B B Fax 44 0 1323 842728 i Support 44 0 1323 444600 www bbvcctv com
21. ilt 16 Full scene presets 2 RX10X preset patrols Pattern Tour 1 learn and playback using AUTOPAN Privacy zone support IR Filter CUT using LIGHTS Lights ON FILTER OFF Lights OFF FILTER ON Videcon Dome TX400DC TX1000 TX1500 Display MENU 1 WASH 1 Display Privacy Menu 2 WIPE 2 Record Pattern Tour 1 3 F AUTOPAN 3 Stop Recording 4 LIGHTS 4 Pattern Tour 1 playback press AUTOPAN The dome and RX10X are linked using RS485 for control and video for the camera signal RX10X Dome Connection Description J6 1 J6 2 J6 3 Gnd J6 4 D DATA J6 5 D DATA Notes The dome switches must be as follows to select Pelco P 9600 baud and address 1 SW1 1 ON 2 7 OFF SW2 1 amp 2 ON Protocol switch 1 4 all OFF When navigating the dome s menu or privacy setup use the joystick and IRIS OPEN and CLOSE The dome manual has detailed information on the menu structure and privacy setting Options Function Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity Option 2 ON to allow LIGHTS to switch the IR CUT filter ON OFF when used with a day night dome RX10X installation manual V1 05 14 Aug 10Page 27 Protocol 06 VIDECON VHSD 870 PELCO D 2400 or 9600 BAUD Variable speed manual Pan Tilt 8 Zoom Focus 16 Full scene presets 2 preset patrols Pattern Tour playback using AUTOPAN Privacy zone support from within dome Menu Videcon VHSD
22. is not connected correctly Check cabling most commonly due to data cables swapped Dome configuration switches if fitted not set correctly Check configuration Interface not seeing Telemetry signal Check that telemetry is present on video cable using either oscilloscope or adjust v hold on monitor to view frame blanking period and check for black white band If missing power down up the transmitter Should this fail swap video between working and non working channels Earth loops can interrupt telemetry operation if sufficiently severe If hum bars are apparent fit isolation transformer to coaxial cable Check the two red 7 segment LED displays mounted on the top PCB on interface see page 11 If the problem persists having followed the above steps technical assistance can be received from Building Block Video Tel 44 0 1323 444600 RX10X installation manual V1 05 14 Aug 10Page 30 Blank for your notes RX10X installation manual V1 05 14 Aug 10Page 31 Extend your BBV Warranty from 12 months to 3 years As of the 1 September 2008 BBV have offered our J Duildiag Black Vides CCTV Microsofi Internet Explore customers the opportunity to extend the standard 12 month Ele fot Yew Fewortes Took Wap warranty to 3 years Q O A Oran rres ES t El Htgcaiweme bbwycctv corakcusboresr _aupportimarerty tiri You must register for the extended warranty within 12 months of the date of manufacture How to register for t
23. lco Spectra 8 Esprit D mode protocol 2400 N 8 1 Variable speed Pan Tilt Zoom Focus Auto focus 16 full scene presets 2 preset patrols Dome Pattern definition and playback Pelco protocol TX400DC TX1000 TX1500 Display dome menu preset 95 1 WASH 1 Reset Head 2 WIPE 2 Pattern define start 3 AUTOPAN 3 Pattern define stop 4 LIGHTS 4 To record a Pattern direct the camera to the required starting position Hold and tap AUTOPAN The dome will now record pan tilt and lens movement up to a time limit To stop the recording hold and tap LIGHTS To play the recorded Pattern press the AUTOPAN key only The dome will repeatedly run the Pattern until either the joystick is moved or the data delay is turned on Menu access Use WASH to display menu Navigate using the joystick and IRIS OPEN to select When used with control systems without iris Keys e g DM Digital Sprite Lite use 889 003 or 889 10 10 3 RS485 control of dome Data rate 2400 Baud No parity 8 Data bits 1 Stop bits Connection details RX10X Dome Connection Description J6 1 J6 2 J6 3 Gnd J6 4 RX DATA J6 5 RX DATA Notes Check with the DM multiplexer manual for exact procedure for entering commands Dome settings Select dome address 1 D MODE PROTOCOL and 2400 N 8 1 Options Function Option 1 enable datum mode goto preset 1 after 5 minutes if inactivity Optio
24. n lt Panning Left at speed 0 lt Panning Left at speed 2 RX10X installation manual V1 05 14 Aug 10 Solder Side EU hora MEN CJ Ur a in fil BBV rcsosoos 22 00000000 ae Tee ey 20mA IN Ea 20mA IN www bbvcctv com vw bbvcctv com Page 14 Dome specific information Dennard 2040 2050 2055 amp 2060 16 GENIE ASD276 8 ASD376 17 JVC TK C655B 675B TK C675E TK C675BE 8 676 18 Panasonic WV CSR400 WV CSR600 8 WV CSR650 19 Panasonic WV CVS 850 amp WV CVS 960 20 Pelco Spectra amp Esprit D protocol 2400 21 Pelco Spectra amp Esprit P protocol 9600 22 Philips Auto Dome RS232 485 23 Sensormatic Ultra Dome 5 6 amp 7 RS422 Only 24 VCL Microsphere Obiter range 25 Vicon Surveyor Range SVFT amp S10 26 Videcon VCP451 amp VHCD 860 27 Videcon VHSD 870 28 Vista Power Dome 29 RX10X installation manual V1 05 14 Aug 10 Page 15 Protocol 08 l Dennard 2040 2050 2055 amp 2060 dome The RX10X can not be powered from the same supply as the Dennard dome Variable speed Pan Tilt Zoom Focus Auto focus 16 full scene presets additional presets can be programmed using dome s menu 2 preset patrols Dennard 2040 2050 2055 amp 2060 TX400DC TX1000 TX1500 Dome User Menu 1 F WASH 1 Dome Supervisor Menu 2 FF WIPE 2 Dome Service Menu 3 F AUTOPAN 3 The domes internal Sequence 001 can be started by pressing AUTOPAN The sequence mus
25. n 2 is used to select the function that is used to drive the Esprit AUX outputs Option 3 is used to send a goto preset 95 or a save preset 95 when 1 is sent to the Rx10X OFF sends a save preset 95 ON sends a goto preset 95 Function OFF ON Esprit AUX No LIGHTS 1 2 WIPER 2 1 WASHER 3 3 RX10X installation manual V1 05 14 Aug 10Page 21 Protocol 01 Pelco Spectra amp Esprit P mode protocol 9600 N 8 1 Variable speed Pan Tilt Zoom Focus Auto focus 16 full scene presets 2 preset patrols Dome Pattern definition and playback Vista up the coax Option 5 Pelco protocol TX400DC TX1000 TX1500 Vista Mux Display dome menu preset 95 1 WASH 1 Goto Preset 25 Reset Head 2 WIPE 2 Goto Preset 26 Pattern define start 3 AUTOPAN 3 Goto Preset 27 Pattern define stop 4 LIGHTS 4 Goto Preset 28 To record a Pattern direct the camera to the required starting position Hold and tap AUTOPAN The dome will now record pan tilt and lens movement up to a time limit To stop the recording hold and tap LIGHTS To play the recorded Pattern press the AUTOPAN key only The dome will repeatedly run the Pattern until either the joystick is moved or the data delay is turned on Menu access Use WASH to display menu Navigate using the joystick and IRIS OPEN to select When used with control systems without iris Keys e g DM Digital Sprite Lite use 889 003 or 889 10 10
26. n VCP451 amp VHCD 860 Videcon VHSD 870 Vista Power Dome 7 Troubleshooting RX10X installation manual V1 05 14 Aug 10 NNN O O O Ol wow 22000 o Page 2 1 PRE INSTALLATION CHECKS AND SAFETY PROCEDURES UNPACKING Check packaging Upon taking delivery of the unit inspect the packaging for signs of damage If damage has occurred advise the carriers and or the suppliers immediately Check contents Upon taking delivery of the unit unpack the unit carefully and check that all the items are present and correct If any items are missing or damaged contact your equipment dealer Retain packaging The shipping carton is the safest container in which to transport the unit Retain undamaged packaging for possible future use IMPORTANT SAFETY PRECAUTIONS Read instructions All relevant safety installation and operating instructions should be read before attempting to install connect or operate the unit Retain Instructions All safety installation and operating instructions should be retained for future reference Heed warnings All warnings on the unit and in any relevant safety installation or operating instructions should be adhered to Cleaning Unplug the unit from the power outlet before cleaning Do not use liguid cleaners or aerosol cleaners Use a damp cloth for cleaning Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards Water and moisture
27. nections RX10X Dome Connection Description J6 1 J6 2 J6 3 Gnd J6 4 COMM IN DATA J6 5 COMM IN DATA Notes Options Function Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity On first entering the menu the dome may autopan and or access the pan tilt menu This is acceptable and simply pressing the Al function will allow the main menu to be displayed If the dome s tour 80 is running start patrol 1 amp 2 is inhibited Accessing the dome menu Press 1 to display menu Use pan tilt keys or joystick to move cursor 1 now acts as the AP key and 2 as the Al key as described on screen 3 and 4 are used as AUX1 and AUX2 during menu programming Presets positions greater than 17 can be programmed using the dome s menu These can be built into Tour 80 which is started by pressing the AUTOPAN key Please refer to dome manual for specific instructions IMPORTANT Dome switch settings for the Surveyor S1 selects dome address please set to address 1 SW1 1 ON others OFF S2 is used to select control method and video standard Set to Simplex data S2 3 ON 8 VPS with S2 2 0FF SW2 1 5 6 7 amp 8 OFF For other versions of dome that do not support auto baud rate detect ensure that baud set for 9600 Please check Vicon manual to confirm switch settings RX10X installation manual V1 05 14 Aug 10Page 26 Protocol 05 Videcon VCP451 8 VHCD 860 Application Notes Variable speed Pan T
28. on the protocol amp finally the option number Then you will see a red flashing dot to show the RX10X is running RX10X installation manual V1 05 14 Aug 10 Page 9 Protocol Selection Table VISTA U Protocol Data out Dome or Camera Protocol Camera Page The aes Number Address Number Supported Laptop De Bug 38400 N 8 1 PC TEST 00 None 14 NO Pelco P 9600 N 8 1 Spectra 8 Esprit 01 01 22 YES Pelco D 2400 N 8 1 Spectra 8 Esprit 02 01 21 NO VCL485 9600 N 8 1 Microsphere amp Orbiter range 03 01 25 YES Vicon 9600 N 8 2 Surveyor Range SVFT 8 S10 04 01 26 NO Videcon 9600 N 8 1 VCP451 amp VHCD 860 05 01 27 NO Videcon 2400 N 8 1 VHSD870 06 01 28 NO Sensormatic RS422 4800 N 8 2 Ultra Dome 5 6 7 amp 8 07 01 24 YES Dennard 9600 N 8 1 2040 2050 2055 8 2060 08 01 16 NO WV CSR400 WV CSR600 Panasonic 650 19200 N 8 1 amp WV CSR650 09 01 19 NO Panasonic 850 19200 N 8 1 WV CVS 850 8 WV CVS 960 10 01 20 YES TK C655B 675B TK C675E JVC 9600 E 8 1 TK C675BE amp 676 11 01 18 YES Vista 9600 N 8 1 Power Dome Range 12 01 29 NO Philips RS232 485 9600 N 8 1 LTC 0929 15 13 01 23 NO Genie ASD276 8 ASD376 2400 N 8 1 ASD276 amp ASD376 14 01 17 NO Please note VISTA Up The Coax supported dome protocols have been tested on a limited number of VISTA control system it is the responsibility of the customer to prove compatibility with the RX10X and you systems particular VISTA
29. reen 5 Way IMO Serial RS232 422 485 to dome J6 Pins 3 4 amp 5 Bottom Green 5 Way IMO RX10X installation manual V1 05 14 Aug 10 Page 8 4 SETUP On power up the unit will display the following information in order Version This would mean version 1 Protocol l This would mean Protocol 12 Mode This would mean Mode4 3 To change either the protocol or the options value Press the centre button sw2 a value between 0 and 32 will be displayed Protocol select protocol selection table is on page 10 By holding the top button sw1 down the value shown on the display will decrement through the available values By holding the bottom button sw3 down the value shown on the display will increment through the available values Once the required value is displayed then press the centre button sw2 again and the display will show to indicate that the value has been entered Then the option value will then be displayed Mode select mode selection table is on page 11 By holding the top button sw1 down the value shown on the display will decrement through the available values By holding the bottom button sw3 down the value shown on the display will increment through the available values Once the required value is displayed then press the centre button sw2 again and the display will show to indicate that the value has been entered It will then show the software versi
30. t be programmed from the dome supervisor menu RS485 control of dome using the following connections RX10X Dome Cable 7 pin plug Description J6 1 J6 2 J6 3 J6 4 Bs Green Pin 3 DATA J6 5 Bs Yellow Pin 4 DATA The Dome must be addressed as 1 this is achieved by setting BLUE rotary sw to 0 8 YELLOW rotary sw to1 Notes Accessing the dome menus Press relevant key combination to display menu To select highlighted menu item perform a Goto preset 1 function as follows TX1500 press 1 followed be the preset key TX1000 Hold the PRESET key and tap the CAM1 key Tx400 press the PRESET1 key The cursor can be moved using the standard pan tilt keys or joystick If the cursor direction is reversed the pan and tilt cursor directions can be reversed from the SUPERVISOR USER OPTIONS CURSOR CONTROL REVERSE menu Presets positions greater than 17 can be programmed using the dome s menu and can be built into dome seguences Please refer to dome manual for specific instructions regarding programming of seguences Options _ Function Option 1 Enable datum mode goto preset 1 after 5 minutes if inactivity RX10X installation manual V1 05 14 Aug 10Page 16 Protocol 14 GENIE ASD276 8 ASD376 PELCO D 2400 Variable speed manual Pan Tilt amp Zoom Focus 16 Full scene presets 2 preset patrols Pattern Tour playback using AUTOPAN GENIE ASD276 8 ASD376 TX400DC TX1000 TX1500 DOME Menu preset 95 1 WASH 1
31. transmitter RX10X installation manual V1 05 14 Aug 10 Page 10 Options Each protocol supports different features which are triggered by selecting different modes in the RX10X The following table indicates how to choose the correct mode number Please refer the dome specific information later in the manual the different mode selects different options to be implemented For example mode number 01 has just option 1 on This will cause the dome to go back to preset 1 after 5 minutes of inactivity This will stop a patrol that might be started by a keypad Option 5 Vista mode this allows the following domes JVC TK C655B 675B TK C675E TK C675BE amp 676 Panasonic WV CVS 850 8 WV CVS 960 Pelco P Spectra amp Esprit Sensormatic Ultra Dome 5 6 8 7 and VCL Microsphere amp Orbiter range to be controlled by Vista up the coax Option 8 Mode Selection Table z Mode Option 5 Option 4 Option 3 Option 2 Option 1 Number OFF OFF OFF OFF OFF 00 OFF OFF OFF OFF ON 01 OFF OFF OFF ON OFF 02 OFF OFF OFF ON ON 03 OFF OFF ON OFF OFF 04 OFF OFF ON OFF ON 05 OFF OFF ON ON OFF 06 OFF OFF ON ON ON 07 OFF ON OFF OFF OFF 08 OFF ON OFF OFF ON 09 OFF ON OFF ON OFF 10 OFF ON OFF ON ON 11 OFF ON ON OFF OFF 12 OFF ON ON OFF ON 13 OFF ON ON ON OFF 14 OFF ON ON ON ON 15 ON OFF OFF OFF OFF 16 ON OFF OFF OFF ON 17 ON OF
32. with Gain and Lift controls Telemetry signals either e Up the coax max distances 250M of RG59 500M of CT125 RG11 e Or twisted pair 0 20mA current loop 300 Ohm close loop impedance maximum 1V p p 750 terminated input via BNC socket 1V p p to V p p 750 impedance via BNC socket Up to 16 full scene preset positions can be stored within the interface depending upon the model of dome Length 69mm Width 57mm Height 36mm 130 grams 10 Celsius to 40 Celsius RX10X installation manual V1 05 14 Aug 10 Page 5 TRANSMITTER COMPATIBILITY CHART TX300 TX400 TX400DC TX1000 TX1000DC TX1500 Variable 2 2 Proportional 2 Proportional Proportional Speed Speeds Speeds Joystick Speeds Joystick Joystick Fixed Y Y Y Y Y Y Speed Zoom Y Y Y Y Y Y Focus v v v v v v Iris Y Y Y Y Y Y Pre sets 8 8 1 6 1 6 1 6 Patrols 2 2 2 2 2 Lights v Y v Y vA Y Autopan v Y Y Y Y Camera E Y Y Y Sf of Functions RX10X installation manual V1 05 14 Aug 10 Page 6 CABLE CONNECTION METHOD 5 way screw terminal plug Fig 1 Cable connection method CABLING RECOMMENDATIONS FOR THE RX10X INTERFACE aa Video from dome Video to controller 2 1mm coaxial power connector This product is not polarity sensitive COAX 75 ohm BNCs TWISTED PAIR Attenuation Cable Type Inner Dielectric Braiding pois Impedance Capacitance ada figures in yp condu

Manual - Videcon

Contents

Download Pdf Manuals

Related Search

Related Contents