Relay Output - MORNSUN POWER
Contents
1. F S MORNSUN D o N x S 7 F XXXX XX ae 9 lofi fiz 13 14 15 16 QB O 4 SN SSN sees Note IN o J222 Unit mm inch o i ae Small white box L W H 165 155 40 Packaging quantity 1pcs La 115 20 4 535 22 50 0 886 Inner carton L W H 425 175 160 Packaging quantity 10 pcs Note Outer carton L W H 560 450 520 Unit mmf inch Packaging quantity 90pcs Wire range 28 12 AWG General tolerances 1 00 0 039 THIRD ANGLE PROJECTION ai Note 1 All specifications are measured at Ta 25 C humidity lt 75 nominal input voltage and rated output load unless otherwise specified 2 In this datasheet all the test setup and methods are based on our corporate standards 3 All characteristics are for listed models and non standard models may perform differently Please contact our technical support for more details 4 Please contact our technical support for any specific requirement 5 Specifications of this product are subject to changes without prior notice MORNSUN Science amp Technology Co Ltd Address No 5 Kehui St 1 Kehui development center Science Ave Guangzhou Science City Luogang district Guangzhou P R China Tel 86 20 38601850 Fax 86 20 38601272 E mail info mornsun cn Http www mornsun power com The copyright and authority for the interpretation of the products are reserved by MORNSUN TSX00 EX 2013 07 01 A 4 Page 3 of 32. MORNSUN Isolating Safety Switching Barrier Fitted devices 1 NAMUR Sensors Relay Output 2 Mechanical Joints TSX00 EX Series Phase angel and inverse control setting e Open circuit detection setting e Operation Temperature 25 C to 71 C e Reliable Performance MIBF gt 1 000 000 hours PART NUMBER SYSTEM GENERAL DESCRIPTION TS200 EX This Isolation Switching Barrier can detect switch or approach Safety barrier mark switch s status in locations where hazardous exists isolate transmit Relay output and output it to safe area Input and output can be set to inverse Channel number Signal style Product seriers PRODUCT PROGRAM control Approach switch open circuit detection function Isolation between Input Output Power source Input Power Output Hazardous end Output Channel Part number Voltage VDC Voltage Short Circuit iStie end numbers Typ Range Typ Current TS100 TS200 24 18 36 8 VDC about 8 mA Relay Output TS100 EX TS200 EX ELECTRICAL SPECIFICATIONS E ERI Operation voltage 18 36VDC Input frequency About 2 0W with relay output OFF Power indicating LED light green ON when operating Switch status of NAMUR sensor Input Signal be ad ne mechanical joint etc Hazardous Distribution voltage About 8V Open status parameter Area Short circuit current About 8mA Open circuit threshold current lt 0 1mA Switching threshold Typ 1 55mA h
3. TRE FOR EXPLOSION OTHER SPECIFICATIONS Operation temperature 25 C 71 C Ambient temperature Transport and Storage temperature 50 C 105 C 35mm DIN rail package hot plug thickness 22 5mm Plastic UL94 VO Safety Grade IP20 IEC60529 EN60529 Weight About 128g CONNECTION In intrinsic safety explosion protection systems isolating barrier belongs to affiliated device It is installed at safe area as a connection between intrinsic safety devices in the hazardous area and non intrinsic safety devices in the safe area By limiting the energy to a certain safe amount it ensures the safety of in spot devices and people Selection regulations for intrinsic safety explosion protection system 1 The explosion protection grade of the barrier must be equal to or higher than that of in spot intrinsic safety explosion protection device 2 Take inconsideration of hazardous end output resistance and loop resistance make sure the barrier s output voltage meets the minimum operation voltage requirement of in spot intrinsic safety device 3 The safety parameters of Barrier s intrinsic safety end meets Uo lt Ul lo lt lin Po lt Pin Co 2 Cin Lo Lin 4 Select suitable Safety barrier which matches the in spot intrinsic safety device for the power s phase signal type and transmission mode 5 Apply necessary protections avoid influence the in spot intrinsic safety device s operation from leakage current that generated by safe
4. ty barrier Operation notes 1 Please read the user manual carefully before using If any questions please contact our technical support department 2 Please do not use this product in hazardous area 3 The power supply of this product should be 24VDC power source It is forbidden to use 220VAC power supply 4 To avoid invalid explosion protection function or any failure users disassemble this product is forbidden APPLICATION CIRCUIT DIAGRAM amp PIN DESCRIPTION Hazardous area Safe area ff N DCS gt O S SS 6 0 D o gt 7 a PLC moO CHo Power Note In single model channel 2 is invalid The copyright and authority for the interpretation of the products are reserved by MORNSUN TSX00 EX 2013 07 01 A 4 Page 2 of 3 INSTALLATION amp DISASSEMBLY Installation Disassembly DINSSmm standard rail installation 1 Use a screwdriver Width of edge lt 6mm cut in the metal card lock 1 Insert the top of the instrument card in the rail from the underside 2 Push the bottom of the instrument into the rail 2 Boost up the screwdriver and pry the metal card lock downwards 3 Pull the instrument out of the rail Loe 112 00 4 409 o i 6084 OSI 2059 22202 Safety area
5. ysteresis 0 2mA Output signal Relay output 1 ON joint Response time lt 20mS Driving capability 250VAC 2A or 30VDC 2A Safe Area Load type Resistive load TRANSMISSION SPECIFICATIONS Under phase angel control Input loop current gt 2 1mA relay output close channel indicator light red ON K2 K3 OFF Under inverse control Input loop current gt 2 1mA relay output open channel indicator light red OFF K2 K3 ON Input loop current lt 1 2mA relay output close channel indicator light red ON When connected with NAMUR sensor Input loop current lt 0 05mA open circuit alarm channel yellow indicator light ON To achieve open circuit detection function a 10KQ resistor must be connected to the When connected with common contact joint switch ke switch in parallel Note K2 is setup channel1 to be reverse or not K3 is setup channel2 to be reverse or not The copyright and authority for the interpretation of the products are reserved by MORNSUN TSX00 EX 2013 07 01 A 4 Page 1 of 3 ISOLATION SPECIFICATIONS Output Input 2 5KVAC Power Supply Input 2 5KVAC Five port isolation Power Supply Output 1 5KVAC Output 1 Output 2 1 5KVAC Input 1 Input 2 1 5VAC Electrical isolation Three port isolation Single channel Five port isolation Dual channels Isolation strength 2 5KVAC test for 1minute humidity lt 70 EMC EN61326 STANDARDS amp CERTIFICATES A SENN aa ce oo AND TEST CEN
Download Pdf Manuals
Related Search