DT1000, DT2000, & DT8000
Contents
1. Place Lane etc For example if 4 cars are racing and lane 3 finishes first followed by 4 1 and 2 then the LCD will read 341 2 Pressing RESET or lt SPACE gt will clear the LCD and the timer will be ready to time the next race The DT8000 serial port transmits the finish order and elapsed times for all cars The data sent by the serial port is formatted as 7 bit ASCII characters that can be interpreted by any terminal type program such as Windows 95 s_ Hyper Terminal Refer to Section 4 for details on configuring your PC for communicating with the DT8000 The data sent from the DT8000 to the PC will be similar to the following where the data is provided as 1 Place Lane 1 Place Time 2 Place Lane 2 Place Time etc The following illustrates the data that might be received if four lanes are in use DT8000 NewBold Products 12 5455 22 9831 33 7745 43 8224 12 6790 33 1288 23 2092 43 5644 32 8820 13 5109 43 5134 23 6202 3 Installation Procedure Tools Required To Install Before you get started with your installation you will need to gather a few hand tools and related items required to test and operate the DTX000 The required items are 1 Hand held Drill amp 3 8 inch drill bit 2 Wire cutters or scissors 3 Light source typically 1 60 75W Incandescent Bulb for every 3 4 stop sensors 4 Fine Tipped Punch or Nail optional The DTX000 timer start switch and stop sensors are used on the pinewood derby r2. again the DTX000 will display a single dash over the 1 designation Press RESET again to enter the timing mode The timing starts when the start switch moves and will stop when the car passes over the stop sensor The LCD will then display the elapsed time with a resolution of 0 1 ms Press RESET on the DTX000 box or the space bar lt SPACE gt on your PC to clear the LCD and begin a new race An example time display on the LCD is 2 5135 Using the Optional Computer Interface DT1000 DT2000 amp DT8000 This time is also transmitted by the DTX000 serial port connected to an RS 232 port on a Personal Computer PC The time is sent to the PC using 7 bit ASCII characters that can be interpreted by any terminal type program such as the Hyper Terminal program part of the Windows 3 1 95 98 Operating System Refer to Section 4 for details on configuring your PC for communicating with the DTX000 The data sent from the DTX000 to the PC is similar to the following DT8000 shown DT8000 NewBold Products 2 5315 3 1022 2 9673 lt Most recent time Mode 2 DT2000 amp DT8000 models The DTX000 times two lanes when in Mode 2 The DTX000 automatically enters this mode when stop sensors are found connected to sensor inputs 1 and 2 and all other sensor inputs are left open After turning the power on the user should press RESET to clear the Self test display After this RESET the LCD will display 2 LANES to indicate t
3. however you think is best We suggest using the supplied cable ties and cable mounts to attach the cables to the bottom of your track and routing them to the DTX000 display in a bundle if possible 4 Operation General As mentioned in Section 2 at power up the DTX000 will turn on the LED and all segments of the 8 digit LCD The user should press the RESET button to clear this initial state The DTX000 then determines the number of stop sensors connected to the handheld unit Once the software makes this determination an operational mode is set Once set this mode cannot be changed except by powering down removing or connecting additional sensors and reapplying the DTX000 s power If you plan to use the PC interface you should configure the PC s terminal program and connect the DTX000 to the PC prior to applying power to the DTX000 There is no problem with making this connection after power up but your PC will miss the initial information sent from the DTX000 Refer to the end of this section for information on how to configure your terminal program Mode 1 Operation DT1000 DT2000 amp DT8000 In Mode 1 the LED will turn on once the Start Switch moves and turns off when the car crosses the finish line After the car finishes the DTX000 s LCD will display the elapsed time and the PC if connected will also display the elapsed time The LCD will hold this time indefinitely until the user presses the RESET button After t
4. to NewBold Products NewBold Products will repair and return the equipment via Priority Mail or FedEx Ground Faster shipping is available at actual cost Warranty repairs are not applicable for modified or damaged equipment 90 Day Return Policy If for any reason you are not satisfied with your equipment purchase you may return it within 90 days of purchase for a full refund excluding shipping charges Once equipment is received and inspected we will issue a refund This return policy does not apply to any modified or damaged equipment 12
5. Installation and Operating Instructions for the DT1000 DT2000 amp DT8000 Pinewood Derby Finish Line and Timer Software Version 4 0 DT8000 Software Version 2 0 DT1000 amp DT2000 11 20 05 NewBold Products Atlanta GA www newboldproducts com 1 Introduction Thank you for purchasing the DTX000 Pinewood Derby Timer Whether you re a Scout Royal Ambassador Awana or in another group we hope you find the DTX000 helpful in developing your cars and conducting your race events This manual refers to the Pinewood Derby PWD race event We realize that many groups have different names for the event but for simplicity we will use what seems to be the predominant name This manual provides information for three models DT1000 DT2000 and DT8000 Features specific to a particular model are noted in the sections that follow NewBold Products began designing and building PWD timers in 1996 initially a simple one lane timer primarily for developing fast cars That first timer became a marketed product the DT1000 The DT8000 was our second PWD timer and represents a dramatic increase in product capability and performance while maintaining the same affordability that became our trademark with the DT1000 NewBold Products believes that high quality and low cost is possible through using a standard configuration regardless of the application Your DTX000 timer will fit any track from 1 to 8 lanes regardless of length or
6. acetrack as shown in Figure 1 The incandescent light doesn t need to be placed too close to the track probably 3 6 feet above the track is sufficient depending on ambient light conditions Installing the 9V Battery To install the 9V battery you will need to remove the back cover from the handheld unit Remove the six machine screws that hold the two halves together Remove the back cover and install the 9V battery into the black battery holder near the bottom of the circuit card Replace the cover and install the six machine screws Using the 9V Wall Adapter The wall adaptor that NewBold Product sells is a 2 1mm plug 9VDC output adapter with the center conductor having the Positive polarity Warning Using a wall adapter with the incorrect polarity will damage your timer making it inoperable Incandescent i Garter Peg Light Source Finish TE Line w Sensors N a l Software Options Gable to Cables to gt F Gop Sensors Hyperemninal free Gart Switch RaceVIEW sills DeroyMaster Gart Lever re w Switch Serial Cable DB9F to DB9M DTX000 Timer Figure 1 Timer Switch and Sensors Installing the Stop Sensor s see Figure 2 To begin your installation decide where you will place the stop sensor s They should be located at your track s finish line normally 32 feet from the starting line and also as close to the centerline of each lane as possible Note that not all tracks ar
7. ane to finish as well or timeout after 9 9999 seconds After all cars have finished the DT8000 s LCD will display the finishing order by lane number The PC if connected will display the finish order and elapsed times for all lanes The LCD will hold with this information indefinitely until the user presses the RESET button After the user presses RESET the DT8000 will clear the LCD and wait for the Start Switch to move This cycle repeats continuously Configuring Your PC s Terminal Program DT1000 DT2000 amp DT8000 The DTX000 sends data to your PC at 1200 baud with 7 data bits no parity and 2 stop bits You should also turn flow control OFF If you are using the Windows 95 operating system on your computer you likely have the terminal program Hyper Terminal This program can be found under lt Start gt lt Programs gt lt Accessories gt lt Hyper Terminal gt Once you have started this program go to lt File gt lt New Connection gt The program will prompt you for a name you could call the session DTX000 or whatever you prefer After giving a name you will have a phone number dialog box From this dialog box edit the Connect Using box to say Direct to Comx Where Comx is Com1 Com2 etc The serial port for many PCs will be Com1 but this varies After entering your Com port and lt OK gt you will see a Comx Properties dialog box At this box enter the connection properties as Bi
8. e 32 feet in length but 32 feet is probably the most common Regardless of length it is important that each sensor be equal distance from the starting line to avoid errors in timing and finish order Important The stop sensor has a polarity therefore it will only operate when connected in one way Connect the sensor to the handheld unit so that the STRIPED wire or COPPER color wire is on the TOP wire the wire closest to the front of the timer should have the stripe Cars Sop Guide Rail Sensor i rr El l gSensorCable l 3 8 Diameter Track Sde Wew Drilled Hole re f le FF i j lane A t lane B 2 i 4 i Finish Line Track Top Vew Figure 2 Sensor Installation The sensor diameter is 0 38 Once you have measured and marked the locations for the stop sensors use a fine tipped punch or nail to make a starting indention This will help keep the drill bit well centered when you begin to drill You should consider using a smaller drill bit to make a pilot hole This pilot hole will keep the larger drill bit more precisely on your center mark If this is going to be a permanent installation you can glue each sensor in place using epoxy a hot glue gun or other suitable glue If you plan to use the DTX000 on multiple tracks you probably want to make the sensor installation more temporary using a weak glue or tape Also you may not need any glue at all if your sensors fit snugly int
9. f you have very low times such as 0 2000 seconds this indicates your light source is too low Move the light source 3 6 inches closer to the stop sensors and retest Test using 1 or 2 lanes only to verify the elapsed time without using a computer 11 7 4 Timer does not appear to stop Recommendation You may have too much light over the sensor Back the light off some and try again See section 7 1 for how to adjust the lighting 7 5 Serial interface not sending data to computer Recommendations 1 Verify that the cable is well connected to both the timer and PC 2 Confirm that the cable is a straight through or 1 1 cable this means that pin 2 connects to pin 2 pin 3 to pin 3 etc 3 Make sure that the serial port is configured properly if using Hyperterminal or Procomm 4 Verify that the connector you are using on your PC is really the Comm port you think it is to test this disconnect the PC interface cable at the DTX000 end short pins 2 and 3 together and using Hyperterminal type information on the keyboard this info should be echoed back to your PC s monitor if you have selected the correct Comm port 5 Verify that your PC is not running any background applications that may be interfering with the Comm port such as Palm Desktop applications Under Win 95 98 the right side of the task bar shows programs that are resident in memory some of these may need to be closed to allow your PC to talk to the Comm port 7 6 DerbyMa
10. g technologies to enhance your race event Perhaps one of the most important benefits of using consumer electronics for your display is that most of these solutions can be implemented at zero cost to your group These solutions are presented for information only and they do not have to be implemented exactly as described here In fact we expect that these ideas will only be a starting point for your group Let us know how you implement your display and we ll provide this information in future manuals Disclaimer NewBold Products does not formally endorse any of the following products manufacturers or distributors expressly but we are suggesting a few possible products as a starting point These products are available from reputable dealers and manufacturers and have their own respective warranties etc VGA to NTSC Converter NTSC is the standard video format that TVs use in North America Converters are widely available which convert your PC s VGA signal to an NTSC signal that can then be displayed on any TV Several VGA to NTSC converters are mentioned in the following paragraph By sending your VGA signal through a converter and to a big screen TV such as a 27 or larger you can provide a very large real time display system for your race You could also split the NTSC signal and run two TVs one on each side of your track or one at the starting line one at the finish line Total cost lt 100 using loaned or rented TVs Potential Sol
11. hat two stop sensors were found After pressing RESET again the LCD will display two dashes in the 1 and 2 locations After pressing RESET again the DTX000 will enter the timing mode Timing starts when the start switch moves and continues until both cars have crossed the finish line passing over the stop sensors The LCD will first display the winning car s lane number and the elapsed time for that car For the first place car the lane number will be shown in the far left digit directly above the label that reads 4 Sho For example if the car in lane 2 finishes first the LCD display might read 2 2 5135 After displaying the winning lane and elapsed time the user should press RESET or lt SPACE gt to display the a place lane number and elapsed time The second place lane number is displayed on the LCD in the second digit of the display directly above the label that reads roe Pressing RESET or lt SPACE gt again will clear the LCD and the timer will be ready to time the next race Using a Computer to Display Finish Order and Times If you would like to display and perhaps save the race results you can see this information by using the DTX000 serial port It will display the finish order and elapsed times for both cars The data sent by the serial port is formatted as 7 bit ASCII characters that can be interpreted by any terminal type program such as Windows 95 s Hyper Terminal Refer to Section 4 of this manua
12. he microcontroller and the timing hardware that measures your car s elapsed time The frequency stability of this oscillator is 100 ppm For a measured time of 2 5 seconds the actual or true time may be 2 5 0 00025 seconds However the frequency stability is specified over a 10 to 70 C temperature range Since the DTX000 normally operates over a confined temperature range of 15 to 30 C the working frequency stability is much better 20 ppm This translates to a measurement error of 0 00005 This is very good since it is one half of the DTX000 s time resolution 7 Troubleshooting 7 1 Cars are not stopping timer Recommendations Check the lighting Adjust the lighting away from the timer so that the sensors are not found when timer is switched on Then move the lighting closer to the track in 6 or 12 increments continue turning the timer on and pressing reset to see if all lanes are recognized Stop moving the light closer once all lanes are found Minimize unnecessary ambient lighting if this seems to be a problem Flash photography is not a problem with the DTX000 7 2 Stop sensors are not found Recommendations verify that enough light is present over the sensor 60W for every 3 4 lanes also make sure you are using an incandescent type of light Verify that the sensors are plugged into the handheld unit with the correct polarity copper facing up 7 3 Timing or start stop seem erratic Recommendation I
13. he user presses RESET the DTX000 will clear the LCD and wait for the Start Switch to move This cycle repeats continuously Mode 2 Operation DT2000 amp DT8000 In Mode 2 the LED will turn on once the Start Switch moves and turns off after both cars cross the finish line for lanes 1 and 2 After both cars have finished the DTX000 s LCD will display the winning car s lane number and the elapsed time for that lane After the user presses RESET the LCD will display the second place car s lane number and elapsed time The PC if connected will display the finish order and elapsed times for both lanes The LCD will hold with this information indefinitely until the user presses the RESET button After the user presses RESET a second time the DTX000 will clear the LCD and wait for the Start Switch to move This cycle repeats continuously Mode 3 Operation DT8000 only In Mode 3 the LED will turn on once the Start Switch moves and turns off after all cars have crossed the finish line In this mode the number of lanes in use can be any number from 3 to 8 and the stop sensors can be connected to any position at the 18 pin header For example the user can have 4 lanes connected to DTX000 connections for lanes 3 4 and 6 and 8 The DTX000 will wait for these four lanes to finish Important Only connect stop sensors for those lanes in use Having additional sensors connected will cause the DTX000 to wait for the additional l
14. implement your large screen display for little or no cost Large Computer Monitor 10 Many computer users are using fairly large monitors such as 17 19 or even 21 These monitors may be large enough for some applications to serve as your large group display LCD Projector borrow from local company or rent Very LARGE Display Some members of your group may be able to borrow an LCD Projector from work for your race event These LCD Projectors take a VGA or SVGA monitor signal and project it onto a wall or screen These projectors have the advantage of making a very large display useful for extremely large groups They may also be available as a rental item from your local computer store This is becoming perhaps the most popular way to display race results 6 Specifications Power Consumption The Handheld unit operates from a 9V battery or AC adaptor Typical alkaline batteries provide about 580 mAh of current to 4 8V at which point the battery should be replaced The current required by the DTX000 varies depending upon how many stop sensors are connected The current requirements and approximate battery life assuming an alkaline battery are provided below of Lanes Current mA Baitery Life Hrs 1 24 6 22 2 27 2 19 8 3 29 8 18 1 4 32 4 16 6 5 35 0 15 4 6 37 6 14 4 7 40 2 13 4 8 42 8 12 6 10 24 MHz Crystal Oscillator The DTX000 uses a 10 24 MHz Crystal Oscillator to run t
15. l for details on configuring your PC for communicating with the DTX000 The data sent from the DTX000 to the PC will be similar to the following where the data is provided as 1 Place Lane 1 Place Time 2 Place Lane 2 Place Time Each new race that is run will have a new set of times incrementally displayed on the computer screen The times displayed on the bottom row are the most recent results DT2000 shown DT2000 NewBold Products 12 5455 22 9831 12 6790 23 1288 22 8820 13 5109 Mode 3 DT8000 only Mode 3 is for installations where 3 or more lanes are to be used up to a maximum of 8 The DT8000 automatically enters this mode when stop sensors are connected to 3 or more sensor inputs All unused sensor inputs should be left open After turning the power on the user should press RESET to clear the Self test display After this RESET the LCD will display X LANES to indicate that stop sensors were found on X Lanes where X 3 to 8 After pressing RESET again the LCD will display a dash in the location where each sensor was found After pressing RESET again the DT8000 will enter the timing mode Timing starts when the start switch moves and continues until all cars have crossed the finish line passing over the stop sensors or the elapsed time is gt 9 9999 seconds Once the last car has finished the LCD will display the finishing order for all cars The LCD data is formatted to display from left to right 1 Place Lane 2
16. lane spacing and can be used on tracks of different groups without any modification To accomplish this the DTX000 automatically determines the track configuration and adjusts to provide the maximum information possible A serial port connection interfaces to virtually any PC and does not require any custom software The DTX000 is a software driven device making the basic system flexible and inexpensive While control and display functions are software based all critical timing operations are performed in hardware to ensure precision FEATURES Timing accuracy to resolution of 0 1 ms 0001 sec Maximum time of 9 9999 seconds 8 Digit Liquid Crystal Display LCD Provides elapsed time and finish order for 1 to 8 lanes depending on model Configurable for use on ANY track regardless of length or width PC Interface connects to any PC serial port PC Interface can be used with virtually any PC and NO custom software is required PC can reset timer by pressing space bar lt SPACE gt PC sends 20h to DT8000 Single configuration regardless of number of lanes in use Automatically determines lanes in use and selects the correct operating mode Simple and easy to learn user interface ABOUT THIS MANUAL The DTX000 Users Manual contains the information that you need to install and operate the system and to conduct your Pinewood Derby event If you are reading this document on your computer you can use the bl
17. o your drilled holes Cable ties and cable holders are provided with your timer You can position the cable holders on the bottom or sides of your track and use the adhesive back to attach them The cable ties can then be used to bundle your wires together for a neater installation The stop sensors are provided with 10 foot wire lengths so the DTX000 handheld unit should be located about 5 6 feet up from your finish line and several feet away from the track Installing the Start Switch see Figure 3 Typically the starter s lever is implemented in a variety of ways The start switch can be mounted to the side of the track with screws epoxy hot glue etc The exact implementation is dependent on your particular track design The start switch needs to be installed so that the switch opens when the starting lever of your track moves to start the race Also be sure to move the lever quickly so that cars are not leaning on the Starting Peg as it moves forward If you impede the car s progress with the Starting Peg the elapsed times can vary from race to race dependent on the speed at which the lever is moved The start switch is supplied with a 40 foot cable length Garting Peg x Qart Witch Closed Pior to Sart Install using wood screws epoxy etc L e may require a small Bi Qarters Lever standoff block of wood to position switch under lever Figure 3 Start Switch Installation Routing Cables You can route your cables
18. on 2 hardware and later 6 AC adaptor connection allows use of a 9V wall adaptor in place of 9V battery Version 2 hardware and later 7 18 pin Header connections for start switch and stop sensors 1 8 8 DB9 Female connection for PC interface mates with DB9 Male connector Turning on the DTX000 Self Test and Selecting the Correct Operating Mode 1 Turn the power on by moving the Power switch up 2 The handheld unit now performs a Self Test It turns on all segments of the LCD and turns on the LED to allow the user a check of all the displays 3 Once the Self Test is complete press the RESET button to clear the display and the LED At this point the DTX000 automatically determines how many stop sensors are connected and which operating mode you will be using IMPORTANT NOTE A sensor is only found present for a given lane if adequate light is present on the sensor for that lane The LCD will display the number of lanes found i e 3 LANES If no lanes are found the LCD will display This indicates the error situation where no stop sensors are found present If this error is displayed the user should check the stop sensor connections and light sources Make sure all sensors are plugged into the unit and make sure all lights are placed closely above the sensors Then turn the power off and back on using the On Off switch Make sure the correct number of lanes is displayed before continuing 4 Once
19. ster Problems Please refer to in program help documentation found when running DerbyMaster or contact Enterprising Ideas at 1 972 394 0381 or on the web at www derbymaster com 7 7 RaceVIEW Problems Please refer to the in program help documentation found when running RaceVIEW or contact RaceVIEW at 1 860 514 4017 or on the web at www raceview com 7 8 Grand Prix Race Manager Problems Please refer to the in program help documentation found when running Grand Prix Race Manager or contact Lisano Enterprises at 1 303 362 1300 or on the web at www grandprix software central com gprm 8 Contacting NewBold Products Warranty and Return Policies We would very much like to HEAR from YOU regarding the DTX000 and how you used it for your car preparations and race event Thanks for your input Send us email feedback newboldproducts com Call us 1 866 NEW BOLD or 678 352 0084 Fax 678 352 1444 Mail NewBold Products 1200 Oakhaven Drive Roswell GA 30075 6 Year Parts amp Labor Warranty NewBold Products provides a six year warranty for all equipment starting from date of purchase and covering parts and labor If you believe your equipment needs warranty repair contact us to let us know the nature of the problem and so that we can resolve it over the phone if possible If the problem cannot be corrected over the phone we will request the equipment be returned to us for repair The customer is responsible for shipping the product back
20. the number of lanes is found and is correct the user should press RESET 5 After pressing RESET a second time the LCD displays on which lanes sensors were found A dash is illuminated for each sensor found For example if you have a 6 lane track and only 5 sensors are found the LCD might show the following to indicate that sensors were found connected to inputs for lanes 1 2 3 5 and 6 This allows the operator to quickly identify a problem connection DT2000 models have 2 lanes max and DT1000 models use a single lane 6 Press RESET again to enter timing mode The DTX000 will enter one of three timing modes based on the number of lanes found present Mode 1 1 Lane is Present DT1000 DT2000 amp DT8000 Mode 2 2 Lanes are Present DT2000 amp DT8000 Mode 3 3 to 8 Lanes are Present DT8000 only When the DTX000 enters timing mode the LCD will be blank and the LED will be off Mode 1 DT1000 DT2000 and DT8000 models In Mode 1 the DTX000 times a single lane This mode can be used for car development prior to race events and for conducting single lane time trials For this mode to work the stop sensor must be connected to sensor input 1 and all other sensor inputs should be left open After turning the power on the user should press RESET to clear the Self test display After this RESET the LCD will display 1 LANE to indicate that the stop sensor was found on for Lane 1 After pressing RESET
21. top Sensors amp cables 10 foot length standard 1 stop sensor shipped standard for DT1000 2 stop sensors shipped standard with DT2000 3 stop sensors shipped standard with DT8000 Five Cable Mounts amp Cable Ties Some orders may contain additional equipment such as Stop Sensors for tracks with 4 or more lanes PC Interface cable AC adapter Carrying Case and Race Management Software Note that the PC Interface cable is a standard DB9 Male to DB9 Female cable with a straight through or 1 1 configuration available from most computer and electronics stores Race Management Software such as DerbyMaster and RaceVIEW is available to enhance the use of the DTX000 s PC interface NewBold Products is a distributor for DerbyMaster software from Enterprising Ideas while RaceVIEW is available for purchase from Wilson Associates www raceview com 2 Functional Description Unit Display Interfaces and Controls The DTX000 system is comprised of the handheld unit start switch and stop sensor s The handheld unit has eight 8 areas of interest These items are 1 8 Digit LCD displays finish order and or elapsed time depending upon mode 2 Green LED when on indicates that the DTX000 is timing a race 3 Reset Button used to clear Self Test displays and to reset prior to a new race 4 On Off Switch turns on power to DTX000 5 Low Battery LED Red LED above power switch turns on when battery is low Versi
22. ts per second 1200 Data bits 7 Parity none Stop bits 2 Flow control none Once you have setup your session you can save it as DTX000 or another name and each time you use the DTX000 you can startup Hyper Terminal and simply load this file If you are using another communications program such as ProComm you can make a similar setup file only the steps will vary slightly Note on Font sizes When using the Hyper Terminal program or others you can change the font size as required For the best results especially for large group displays as in Section 5 you may want to adjust your font so that your results for a single race fill the majority of the screen s width This works particularly well for setups with less than 5 lanes 5 Large Group Displays NewBold Products has designed the DTX000 to be as affordable as possible and yet provide maximum performance and flexibility Yet for some Pinewood Derby events the race results need to be displayed so that large groups can all view the information in real time This real time feedback adds excitement to the entire event Because each group will have unique requirements NewBold Products has included in this section a number of display alternatives During the late 90 s the consumer electronics industry has made large screen TVs large computer monitors and camcorders affordable to nearly everyone It is the intention of this section to make the best use of these existin
23. ue hyperlinks to jump between sections You should read the entire manual to fully understand and properly use the DTX000 At a minimum you should read sections 2 3 and 4 Section 2 provides a functional description of the DTX000 describing connections LCD display start switch Personal Computer interface and a description of each operational mode Section 3 provides installation information to guide you through installing the start switch stop sensors and placing the DTX000 handheld unit Section 4 describes how the user will use the DTX000 for each mode and specifics on how the unit interfaces to a PC Section 5 is our Large Screen Displays section describing a number of very low cost ways to display both the Finish Order and Elapsed Times for large crowds at a Pinewood Derby event You can use equipment you already have to create an impressive race time display for the audience Section 6 describes a few of the more important specifications of the DTX000 product family and is provided primarily for the more technical reader interested in product details Section 7 is our Troubleshooting section Section 8 describes warranty return policies and ways to contact us RECEIVING YOUR SHIPMENT Your order was carefully packed and inspected prior to shipment Along with this manual your order should contain at a minimum DTX000 Handheld unit DURACELL 9V battery installed Starting Switch amp cable 40 foot length standard S
24. utions Note All of these converters allow you to run your VGA monitor and one or more televisions simultaneously They also all require your television to have either a video or S video input most newer television have both Refer to your television s documentation to confirm that it has this type of video input available PCConnection 1 800 800 0009 www pcconnection com 1 Part 28607 Mfg Focus Enhancements Inc Model Tview Micro Cost 89 95 Features VGA In Composite RCA or S Video out also VGA out NTSC 640 x 480 24 bit color 2 Part 49057 Mfg Focus Enhancements Inc Model Tview Silver Cost 139 95 Features Similar to Tview Micro except for 800 x 600 resolution 3 Part 46511 Mfg Avermedia Inc Cost 139 95 Features VGA In Composite or S Video out also VGA Out 1024 x 768 resolution Jameco Electronics 1 800 831 4242 www jameco com 1 Part 105208 Mfg Avermedia Inc Cost 89 95 Features VGA In NTSC or PAL out also VGA out 640 x 480 resolution 2 Part 150447 Mfg Maruda Cost 89 95 Features VGA In NTSC or PAL output 640 x 480 resolution Laptop with NTSC Output A number of laptops several made by Compaq come standard with a video output intended to drive the video input of a Television or video monitor The laptop s video output can be used to drive a large Television perhaps 27 or larger If you have a member of your group with this type of laptop you may be able to
Download Pdf Manuals
Related Search