20G212-00 E2 User Manual
Contents
1. 20G212 00 E2 2014 01 17 Functional Description Pin Signal Direction Function 24 PETnO in PCI Express transmit signals 25 PETpO 26 GND Power Please refer to the ExpressCard Specification for further details See Chapter 3 1 Literature and Web Resources on page 27 MEN Mikro Elektronik GmbH 20G212 00 E2 2014 01 17 Functional Description 2 4 SIM Card Holder The G212 is equipped with a SIM card holder To get access to a mobile phone network you need a SIM card subscriber identity module and a contract with a mobile service provider Please note that MEN does not provide mobile services or SIM cards Figure 4 Position of SIM card holder SIM Card Holders PCI Express Mini Card Slot 2 ExpressCard Slot 2 Option 4 USB Front Connectors Option Antenna Connectors CompactPCI Serial P1 Connector PCI Express Mini ExpressCard Slot 1 Card Slot 1 Option MEN Mikro Elektronik GmbH 24 20G212 00 E2 2014 01 17 Functional Description 2 5 SMBus Functionality The board can be configured using SMBus The board s SMBus address is set using a hex switch see Chapter Figure 1 Map of the board front panel on page 15 If there are several ICs in your system which are controlled via SMBus there might be address collisions as one address may not occur more than once Via the hex switch you can select an address from a certain address range It is set to a defa2. 1 PCle x1 1 PCle x1 CompactPCl Serial Connector SIM 1 USB 2 0 Card Holder USB Hub MEN Mikro Elektronik GmbH 3 20G212 00 E2 2014 01 17 Technical Data Technical Data Card Interfaces Two PCI Express Mini Cards only full size or Two ExpressCard 34 modules One ExpressCard 54 module SIM card holder USB and PCI Express interface Please note that MEN does not offer SIM cards or mobile telephony contracts Front Connections Four Reverse SMA antenna connectors CompactPCI Serial Compliance with CompactPCI Serial PICMG CPCI S 0 Specification Peripheral slot Host interface one PCI Express x1 link and a differential pair of USB lines PCIe8 1 1 Data rate up to 250 MB s in each direction 2 5 Gbit s per lane USB 2 0 Data rate up to 480 Mbit s Electrical Specifications Supply voltage power consumption 12V 10 10 depending on plugged card 0 1 A max w o card Mechanical Specifications Dimensions conforming to CompactPCI Serial specification for 3U boards Front panel 4HP or 8HP with ejector Weight 134g without cards Environmental Specifications Temperature range operation 40 85 C screened only carrier depending on configuration Airflow min 1 0 m s e Temperature range storage 40 85 C Relative humidity operation max 95 non condensing Relative humidity storage max 9596 non condensing Altitude 300m to 3 000
3. 17 Functional Description 2 Functional Description 2 1 Power Supply The G212 is supplied with a primary 12V voltage via the CompactPCI Serial connector P1 2 2 PCI Express Mini Card Interface PCI Express Mini cards are small form factor PCI Express Cards The main differences between an ExpressCard and a PCI Express Mini Card is a smaller form factor optimized for mobile computing platforms and a card system interconnection optimized for communication applications PCI Express Mini Card cards also use smaller connectors than standard ExpressCards The G212 supports the PCI Express Mini Card Standard but only full size cards can be used A single PCI Express lane x1 and a USB connection are supported on the board MEN Mikro Elektronik GmbH 18 20G212 00 E2 2014 01 17 Functional Description The board is equipped with two 52 pin standard PCI Express Mini Card connectors The following standard signals are supported signal directions according to PCI Express Mini Card Standard Table 1 Pin assignment of 52 pin PCI Express Mini Card connector 52 3 3Vaux 50 GND 48 1 5V 43 GND 41 3 3Vaux 40 GND 39 3 3Vaux 52 51 138 USB_D 37 GND 36 USB_D 35 GND 34 GND 32 SMB_DATA 30 SMB_CLK 29 GND 28 1 5V 27 GND 26 GND 24 3 3Vaux 22 PERST 21 GND 18 GND 2 1 15 GND 14 UIM_RESET 12 UIM CLK 10 UIM DATA 9 GND 8 UIM PWR 6 1 5V 4 GND 2 3 3Vaux 1 WAKE MEN Mikro Elektronik GmbH 19 2
4. Conformity MEN products are no ready made products for end users They are tested according to the standards given in the Technical Data and thus enable you to achieve certification of the product according to the standards applicable in your field of application MEN Mikro Elektronik GmbH 10 20G212 00 E2 2014 01 17 About this Document RoHS Since July 1 2006 all MEN standard products comply with RoHS legislation Since January 2005 the SMD and manual soldering processes at MEN have already been completely lead free Between June 2004 and June 30 2006 MEN s selected component suppliers have changed delivery to RoHS compliant parts During this period any change and status was traceable through the MEN ERP system and the boards gradually became RoHS compliant WEEE Application The WEBE directive does not apply to fixed industrial plants and tools The compliance is the responsibility of the company which puts the product on the market as defined in the directive components and sub assemblies are not subject to product compliance In other words Since MEN does not deliver ready made products to end users the WEEE directive is not applicable for MEN Users are nevertheless recommended to properly recycle all electronic boards which have passed their life cycle Nevertheless MEN is registered as a manufacturer in Germany The registration number can be provided on request Copyright 2014 MEN Mikro Elektronik GmbH All right
5. Power down and unplug your computer system when working on the inside Hold components by the edges and try not to touch the IC chips leads or cir cuitry Use a grounded wrist strap before handling computer components Place components on a grounded antistatic pad or on the bag that came with the component whenever the components are separated from the system Store the board only in its original ESD protected packaging Retain the original packaging in case you need to return the board to MEN for repair MEN Mikro Elektronik GmbH 7 20G212 00 E2 2014 01 17 About this Document About this Document This user manual is intended only for system developers and integrators it is not intended for end users It describes the hardware functions of the board connection of peripheral devices and integration into a system It also provides additional information for special applications and configurations of the board The manual does not include detailed information on individual components data sheets etc A list of literature is given in the appendix History Issue Comments Date E1 First issue 2010 05 10 E2 Added SMBus Functionality chapter 2014 01 16 Fixed pin assignment tables for PCI Express Mini Card MEN Mikro Elektronik GmbH 20G212 00 E2 2014 01 17 Pi About this Document Conventions This sign marks important notes or warnings concerning the use of voltages which can lead to serious
6. damage to your health and also cause damage or destruction of the component This sign marks important notes or warnings concerning proper functionality of the product described in this document You should read them in any case italics Folder file and function names are printed in italics bold Bold type is used for emphasis monospace A monospaced font type is used for hexadecimal numbers listings C function descriptions or wherever appropriate Hexadecimal numbers are preceded by Ox comment Comments embedded into coding examples are shown in green color hyperlink Hyperlinks are printed in blue color The globe will show you where hyperlinks lead directly to the Internet so you can look for the latest information online IRQ Signal names followed by or preceded by a slash indicate that this signal is IRQ either active low or that it becomes active at a falling edge in out Signal directions in signal mnemonics tables generally refer to the corresponding board or component in meaning to the board or component out meaning coming from it Vertical lines on the outer margin signal technical changes to the previous issue of the document MEN Mikro Elektronik GmbH 9 20G212 00 E2 2014 01 17 About this Document Legal Information Changes MEN Mikro Elektronik GmbH MEN reserves the right to make changes without further notice to any products herein Warranty Guarantee Liability MEN makes no warra
7. of the board and some hints for first installation in a system 1 1 Map of the Board Figure 1 Map of the board front panel MEN Mikro Elektronik GmbH 15 20G212 00 E2 2014 01 17 Getting Started Figure 2 Map of the board top view SIM Card Holders PCI Express Mini Card Slot 2 ExpressCard Slot 2 Option 4 USB Front Connectors Option Antenna Connectors CompactPCI Serial P1 Connector PCI Express Mini Card ExpressCard Slot 1 Slot 1 Option MEN Mikro Elektronik GmbH 16 20G212 00 E2 2014 01 17 Getting Started 12 Integrating the Board into a System You can use the following check list when installing the G212 in a CompactPCI Serial system for the first time M Power down the system M Install one or two PCI Express Mini Cards or optionally ExpressCards on the G212 as described in Chapter 2 2 1 Installing a PCI Express Mini Card on page 21 M Insert the G212 into a peripheral slot of your CompactPCI Serial system mak ing sure that the CompactPCI Serial connectors are properly aligned Note The peripheral slots of every CompactPCI Serial system are marked by a circle O on the backplane and or at the front panel MI Power up the system M You can now install driver software 1 3 Installing Driver Software For a detailed description on how to install driver software please refer to the respective documentation MEN Mikro Elektronik GmbH 17 20G212 00 E2 2014 01
8. 0G212 00 E2 2014 01 17 Functional Description Table 2 Signal mnemonics of 52 pin PCI Express Mini Card connector Signal Direction Function Power GND Ground 3 3Vaux 3 3V source 1 5V 1 5V source SIM card UIM PWR out SIM card power UIM DATA in out SIM card data UIM CLK out SIM card clock UIM_RST out SIM card reset PCI REFCLK REF in PCI Express differential reference Express CLK clock PERnO PERpO out PCI Express receive signals PETnO PETpO in PCI Express transmit signals Auxiliary CLKREQ out Clock request Signals PERST in Reset for the Mini Card WAKE out Wake signal USB USB_D in out USB line USB_D in out USB line Please refer to the PCI Express Mini Card Specification for further details See Chapter 3 1 Literature and Web Resources on page 27 MEN Mikro Elektronik GmbH 20 20G212 00 E2 2014 01 17 Functional Description 2 2 1 Installing a PCI Express Mini Card Perform the following steps to install a PCI Express Mini card The required screws are included in the delivery M Insert the PCI Express Mini card into the card connector in a 30 angle M Rotate the card down until it sits firmly in the connector M Screw the PCI Express Mini Card tightly to the G212 See Figure 3 Installing PCI Express Mini Card M Connect the antennae to the PCI Express Mini Card Figure 3 Installing PCI Express Mini Card MEN Mikro Elek
9. 20G212 00 EZ 2014 01 17 G212 3U CompactPCle amp Serial PCle amp Mini Card Carrier Configuration example man G212 3U CompactPCI Serial PCle Mini Card Carrier for Wireless Functions G212 3U CompaciPCIE Serial PCle Mini Card Carrier for Wireless Functions The G212 is a rugged single Eurocard CompactPCI Serial carrier board supporting the PCI Express Mini Card standard or as an option the ExpressCard standard ExpressCard is the successor of the CardBus standard and offers different construction sizes as well as connection via PCI Express or USB 2 0 The standard version of the G212 offers two PCI Express Mini Card slots It allows to use all types of cards for HF applications for example GPS WLAN UMTS GSM or HSDPA Each card is connected to two robust redundant external SMA antenna connectors at the front panel of the G212 Using these standard cards that give access to the whole world of common notebook PC expansions is a fast and easy way to extend the functionality of a CompactPCI Serial system as well The G212 is designed for 40 to 85 C operating temperature and prepared for conformal coating in order to be used also in harsh and mobile environments The final environmental qualification depends on the respective cards used on the carrier MEN Mikro Elektronik GmbH 2 20G212 00 E2 2014 01 17 Diagram Diagram SIM 1 PCle x1 PCI Card Express Holder 1 USB 2 0 Switch
10. D Roo moos SNP Too Txoo PE PE 1 i PN i BMP REFCLK REFCLK J R eao GA2 GA1 GAO 3 PCIE_ PE RST_ IPM IPMB EN GND WAKE INE GND reserved reserved GND B SDA SCL GND 2 GND 12V 12V GND 12V 412V GND 12V 12V GND 1 L K J H G F E D C B A MEN Mikro Elektronik GmbH 26 20G212 00 E2 2014 01 17 Appendix 3 Appendix 34 Literature and Web Resources e G212 data sheet with up to date information and documentation www men de products 02G212 html 3 1 1 PCI Express Mini Card PCI Express Mini Card Electromechanical Specification Revision 1 2 October 26 2007 PCI Special Interest Group www pcisig com 3 1 2 ExpressCard ExpressCard Electromechanical Specification Revision 1 0a PCI Special Interest Group www pcisig com 3 2 Finding out the Product s Article Number Revision and Serial Number MEN user documentation may describe several different models and or design revisions of the G212 You can find information on the article number the design revision and the serial number on two labels attached to the board Article number Gives the product s family and model This is also MEN s ordering number To be complete it must have 9 characters Revision number Gives the design revision of the product Serial number Unique identification assigned during production If you need support you should communicate these numbers to MEN Figure 5 Labels giving the
11. ctPCI Serial Interface 2 x oy tpe dot a 26 MZ STT 27 3 1 Literature and Web Resources ss ssissssisssg sous sus 27 SLI PCI Express Mint Cardy ss a n ducto m n n 27 3 1 2 ExpressCard o4 ecu br teh d di pr SER dern 27 3 2 Finding out the Product s Article Number Revision and Serial NuMDEF s rine date ee redire E EKBRU d 2T MEN Mikro Elektronik GmbH 12 20G212 00 E2 2014 01 17 Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 MEN Mikro Elektronik GmbH 20G212 00 E2 2014 01 17 Map ot the board front panels i eee m menn 15 Map of the board 1Op VIEW 2 2 eom hh etam ees mene een 16 Installing PCI Express Mimi Card sss sss rasista nee 21 Position of SIM card holder 03203 s s sa wa n ke ak al e 24 Labels giving the product s article number revision and Serial TUT D 5o ooo t np konis ka ks ipd kas ears 27 Tables Table 1 Table 2 Table 3 Table 4 Table 5 MEN Mikro Elektronik GmbH 20G212 00 E2 2014 01 17 Pin assignment of 52 pin PCI Express Mini Card connector 19 Signal mnemonics of 52 pin PCI Express Mini Card connector 20 Signal mnemonics of 26 pin ExpressCard connector 22 Position of hex switch for setting the SMBus address 25 Pin assignment of CompactPCI Serial P1 connector 26 14 ting Started 1 Getting Started This chapter gives an overview
12. m Shock 15g 11ms Bump 10g 16ms Vibration sinusoidal 1g 10 150Hz Conformal coating on request MEN Mikro Elektronik GmbH 4 20G212 00 E2 2014 01 17 Technical Data MTBF e MTBF 2 534 034h 40 C according to IEC TR 62380 RDF 2000 Safety PCB manufactured with a flammability rating of 94V 0 by UL recognized manu facturers EMC Conforming to EN 55022 radio disturbance IEC1000 4 2 ESD and IEC1000 4 4 burst Software Support e PCIe8 Mini Card and ExpressCard drivers as supported MEN Mikro Elektronik GmbH oy 20G212 00 E2 2014 01 17 Configuration Options Configuration Options Card Slots Two PCI Express Mini Cards e Two ExpressCard 9 34 modules One ExpressCard 54 module llO e 4 USB interfaces at the front Cooling Concept Also available with conduction cooling in MEN CCA frame Please note that some of these options may only be available for large volumes Please ask our sales staff for more information For available standard configurations see online data sheet do MEN Mikro Elektronik GmbH 6 20G212 00 E2 2014 01 17 Product Safety Product Safety A Electrostatic Discharge ESD Computer boards and components contain electrostatic sensitive devices Electrostatic discharge ESD can damage components To protect the board and other components against damage from static electricity you should follow some precautions whenever you work on your computer
13. nty representation or guarantee of any kind regarding the suitability of its products for any particular purpose nor does MEN assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation consequential or incidental damages TO THE EXTENT APPLICABLE SPECIFICALLY EXCLUDED ARE ANY IMPLIED WARRANTIES ARISING BY OPERATION OF LAW CUSTOM OR USAGE INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OR USE In no event shall MEN be liable for more than the contract price for the products in question If buyer does not notify MEN in writing within the foregoing warranty period MEN shall have no liability or obligation to buyer hereunder The publication is provided on the terms and understanding that 1 MEN is not responsible for the results of any actions taken on the basis of information in the publication nor for any error in or omission from the publication and 2 MEN is not engaged in rendering technical or other advice or services MEN expressly disclaims all and any liability and responsibility to any person whether a reader of the publication or not in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance whether wholly or partially on the whole or any part of the contents of the publication Conditions for Use Field
14. of Application The correct function of MEN products in mission critical and life critical applications is limited to the environmental specification given for each product in the technical user manual The correct function of MEN products under extended environmental conditions is limited to the individual requirement specification and subsequent validation documents for each product for the applicable use case and has to be agreed upon in writing by MEN and the customer Should the customer purchase or use MEN products for any unintended or unauthorized application the customer shall indemnify and hold MEN and its officers employees subsidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim or personal injury or death associated with such unintended or unauthorized use even if such claim alleges that MEN was negligent regarding the design or manufacture of the part In no case is MEN liable for the correct function of the technical installation where MEN products are a part of Trademarks All products or services mentioned in this publication are identified by the trademarks service marks or product names as designated by the companies which market those products The trademarks and registered trademarks are held by the companies producing them Inquiries concerning such trademarks should be made directly to those companies
15. product s article number revision and serial number Complete article number T T ES 641517 Revision number Serial number MEN Mikro Elektronik GmbH 27 20G212 00 E2 2014 01 17
16. s reserved Germany France USA MEN Mikro Elektronik GmbH MEN Mikro Elektronik SA MEN Micro Inc Neuwieder StraBe 3 7 18 rue Ren Cassin 860 Penllyn Blue Bell Pike 90411 Nuremberg ZA de la Chatelaine Blue Bell PA 19422 Phone 49 911 99 33 5 0 74240 Gaillard Phone 215 542 9575 Fax 49 911 99 33 5 901 Phone 33 0 450 955 312 Fax 215 542 9577 E mail info men de Fax 33 0 450 955 211 E mail sales Cmenmicro com www men de E mail info Qmen france fr www menmicro com www men france fr MEN Mikro Elektronik GmbH 11 20G212 00 E2 2014 01 17 Contents Contents 1 Getting Started i siy s sun an so 9 cae te Y eR 2 0 EE one pe RR RUE 15 LI Map Ot the Board js odd iut a vagas iis kakas pda nd 15 1 2 Integrating the Board into a System si ll 17 1 3 Installing Driver Sottware s ca ias ico 1963 2520 RORIS deans sec 17 2 Functional Description ii ss san ne ne a vr ee mon wees menos 18 ZA PowerSupply 2 crei rear pn eee ere n guhan la la eed 18 2 2 PCI Express Mini Card Interface eed Rr er ea 18 2 2 1 Installing a PCI Express Mini Card 21 2 3 ExpressCard Interface Optional ss 51 54 psio s 43 LETS ete 22 2 4 SIM Card Holder uns sene nam e rem ne WERAN sins mae bs 24 2 5 SMBUS Functionality s 323 5c rep re 20052 n oi esis 25 2 5 1 Reset Standard G212 and Other Models with Two SIM Card SIOlS 3 2x2 eb oL err ne EUER ion 25 2 6 Compa
17. tronik GmbH 21 20G212 00 E2 2014 01 17 Functional Description 2 3 ExpressCard Interface Optional According to the ExpressCard standard there are two standard formats of ExpressCard modules the ExpressCard 34 module which is 34 mm wide and the ExpressCard 54 module characterized by its 54 mm width ExpressCard 34 modules and ExpressCard 54 modules both use the same connector interface The board supports both type 34 and 54 A single PCI Express lane x1 and a USB connection are supported on the board The ExpressCards on the G212 cannot be hot plugged as they are mounted behind the front panel The board is equipped with up to two 26 pin standard ExpressCard connectors The following standard signals are supported Table 3 Signal mnemonics of 26 pin ExpressCard connector Pin Signal Direction Function 1 GND Power 2 USBD in out Differential pair of USB lines 3 USBD 4 CPUSB out USB power detection 5 Reserved 6 Reserved 9 1 5V in Power 10 11 WAKE out Wake signal from MiniCard slot 12 3 3V AUX in Power 13 PERST in Express card reset 14 3 3V in Power 15 16 CLKREQ out Clock request from MiniCard slot 17 CPPE out PCle power detection 18 REFCLK in PCI Express differential reference clock 19 REFCLK 20 GND Power 21 PERn0 out PCI Express receive signals 22 PERpO 23 GND Power MEN Mikro Elektronik GmbH
18. ult value at the factory Table 4 Position of hex switch for setting the SMBus address Switch position SMBus Address 0x40 0x42 0x44 0x46 8 A C 0x4 0x4 0x4 Ox4E F not allowed y go NI g a S o 2 5 1 Reset In order to be able to reset the board during operation you can switch off the power supply of the PCI Express Mini Cards or ExpressCards using the SMBus Thus in case of an error the board can be reset without having to shut down the whole system Perform the following steps to switch the power supply on or off M Perform a write byte command on the address of the I2C expander set by the hex switch M Write the value for your required configuration MEN Mikro Elektronik GmbH 25 20G212 00 E2 2014 01 17 2 6 Functional Description CompactPCI Serial Interface The G212 uses one PCI Express x1 link and one USB interface at the backplane according to the CompactPCI Serial specification PICMG CPCI S 0 proposed standard under development Connector type of P1 72 pin Airmax VS 4 pair right angle header 6 IMLA with end walls See Table 5 Pin assignment of CompactPCI Serial P1 connector for the pin assignment of the P1 connector Table 5 Pin assignment of CompactPCI Serial P1 connector u z z amp 2 n 1 A GND GND GND GND 6 PE_ PE_ PE PE EHE i i Che i i 9N
Download Pdf Manuals
Related Search