ANG MF20 - Cassese
Contents
1. E Cassese Quality for the world MF20 AIR OPERATED HANGER FIXER TECHNICAL AND USER MANUAL Version 1 au 04 2001 MF20 TECHNICAL AND USER MANUAL CONTENTS Page N INTRODUCTION ACCESSORIES DELIVERED WITH THE MACHINE SPECIFICATIONS GUARANTEE PUTTING INTO OPERATIONS UNPACKING SETTING UP 2 ADJUSTMENTS SETTING DISTANCE OF HANGER FROM TOP SETTING CENTER OF LONG SHORT DIMENSIONS INSTALLING THE BOTTOM STAMP FOR HANGERS USE USE OF POSITION STOPS FIXING HANGERS 4 MAINTENANCE PREVENTIVE MAINTENANCE 5 MF 20 04 2001 INTRODUCTION You have just bought a Cassese machine Multifix MF20 We congratulate on your sensible choice and thank you for your trust in Cassese products The MF20 benefits from the experience of picture framing equipment that brought Cassese a certain reputation The MF20 is designed to fix special no screw no nail hangers on the backboards of the frames ACCESSORIES DELIVERED WITH THE MACHINE 3 feet with nuts 4 h f i N KA ga Se 1 removable stop a 3 1 Allen key n 5 mm 1 Allen key n 3 i 1 fixed stop SPECIFICATIONS MODEL DESCRIPTION CONSUMPTION WEIGHT DIMENSIONS MF20P Pneumatic hanger fixer 2 L per cycle 60 kg 500 x 550 x 600 mm US gallon 20 x 22 x 24 GUARANTEE The MF20 is guaranteed one year for parts and labour against manufacturing defects Wear parts and those damaged as a result of non appliance with the instru2. make sure only to use the correct position stop left hand removable one for short size and right hand fixed stop for long size Keeping the backboard well in place press the foot pedal fully down don t release too fast the foot pedal Give time to presser head to fix well the hanger Then remove the backboard lift plexi cover and load on machine a second hanger on the bottom stamp Turn the backboard 90 and proceed with the fixing of the other dimension To avoid any mistake it is advised to use the 2 stops as indicated above left hand removable for short size and the right hand fixed one for the long dimension of backboard 4 MAINTENANCE BEFORE ANY TECHNICAL INTERVENTION MAKE SURE THE MACHINE IS DISCONNECTED FROM THE COMPRESSED AIR SOURCE PREVENTIVE MAINTENANCE Lubrication it is advised to open the machine s main frame to grease once every six months these 2 articulations
3. ctions of the present manual are excluded from the guarantee eJ ITEM DESCRIPTION EXPLANATIONS ADVICE Z 7400 Stamp for hanger 1401 With one rosette Remaining flat Small frames thus ideal for volume framers and for shrink wrapping Z 7401 Stamp for hanger 1409 Hinged articulated hanger for Small and medium sized frames French hanging systems Z 7705 Stamp for hanger 1413 Pivoting hanger can be used with All sizes of frames and mirrors hanging wire and as D ring Z 7397 Stamp for hanger 1428 Same as 1409 above but wider Bigger and heavier frames Z 7399 Stamp for hanger 1439 Heavy frames and mirrors Z 7398 Stamp for hanger 1490 With 2 rosettes Comes flat slightly Custom and volume framers open to be lifted by consumer small and medium sized frames Excellent for shrink wrapping consumer Z 7739 Stamp for hanger LB Hanger and support for a feet that Sizes of feet for small and big can be used as strut back easel frames available Z 7933 Stamp for hanger 2602 With 2 rosettes Hanger area larger Custom and volume framers than 1490 thus easier to adjust for Small and medium sized frames for photo frames Z 6411 Accessories needed for 3 sizes of hinges available for strut Add Locator 32 for most popular fixing strut back hinges back photo frames add one locator medium sized hinges For bigger easelbacks part per size of hinge chosen hinges add LOC 31 for sma
4. ll hinges LOC 33 NAQOnmsA WO MF 20 Advised way of fitting AIR LINE FITTINGS USA STANDARD Male Connector on Machine quick release Q R female air connector Z 749 Q R US male Standard hose connector connector Z 701 Z 556 AIR SOURCE compressor UNPACKING SETTING UP AND PUTTING INTO OPERATION The MF20 weighs 60kg 133 Ibs therefore it is strongly advised to unpack and install the machine with the help of a second person oT With a screwdriver remove Remove the cover of The MF20 is fixed with 3 the 8 screws that fix the case the case screws A B C to the skid base to its skid base i F 4 7 4 rl gt E re t AE P a ee eT ae o A 7 Put the MF20 with its wooden base Put the MF20 to its work place inclining the ma on higher wood pieces to create a chine slightly to the sides fix its 3 feet with the bigger space to remove the screws washers and adjust them so that the machine is from underneath you need a 19 not unstable which is the most important reason mm wrench for fast mechanical aging for any eguipment s Open down the 2 arms of MF20 Install Connecting to compressed air supply ma the fixed measure stop on the right hand chine equipped with quick release male con arm the removable stop on the left nector the female one is delivered in the ac hand arm Now push the left and right cessory box This can be used with air tubes arms f
5. ng to 2 pins on machine make sure that you easily Hangers can only be put in one cannot install it badly 3 correct way on the stamp SAFETY The front plexi protection cover is part of the safety system of your Cassese MF 20 It is forbidden to remove it and to use the machine without the safety cover The presser head that carries out the fixing of hangers is connected to the safety cover When the safety cover is open more than 8 mm 5 16 from the machine s work bench the presser head is prevented from making its travel protecting operator s hands 1 USE OF POSITION STOPS see fig 1 Fig N 1 Fig N 2 As the left hand removable stop is used for the short size engage the backboard into the machine in the sense of the short size making sure that you are against the removable stop on the left side and the backboard is well against the back stop BP To use the right hand fixed stop for the long size see fig 2 engage the backboard into the machine in the sense of the long size making sure that you are well against the fixed stop on the right side of the backboard and well against the backstop bar In this case the backboard will be covering the remov able stop but will not be presenting itself inclined as the removable finger will move up a little to al low the backboard to sit flat 1 FIXING HANGERS Put one hanger on the machine rosettes up You can start with any side short or long
6. ully into the profile that is next to inside diameter 8 mm Your source must sup them and block them tightening screw ply to machine 6 bars 85 psi pressure mini V mum dry and non lubricated air 2 ADJUSTMENTS Example At 3 cm from the top of the backboard fixing of 2 hangers 1428 Backboard dimensions 20 x 30 cm 1 SETTING DISTANCE OF HANGER FROM TOP OF BACKBOARD 3 cm E JA O 1 Slide backstop BP to reach 3 cm on Loosen the 2 handles MP that fix the position of back the scales underneath and tighten the stops BP handles BP See fig 4 page 4 2 SETTING CENTER OF LONG AND SHORT DIMENSIONS Use the fixed stop on the right hand side for the center half po sition of the long dimension of the backboard used you divide by 2 long size of backboard to find the correct setting of fixed stop in this mpg case 30 cm 2 15 cm In the same way use the removable stop on the left side for the center position of short dimension in this case 20 cm 2 10 cm You can use the removable finger ofthis stop in lifted position to set it correctly but bring it to down position while working afterwards 3 INSTALLING THE BOTTOM STAMP FOR HANGER M SS VEA Now put 1 hanger with its rosettes up One special bottom stamp for each type of hanger is needed On the stamp that is magnetic and Install it as shown above on the machine 2 holes of different makes sure that the hanger cannot move sizes correspondi
Download Pdf Manuals
Related Search