Installation - Quality Craft
Contents
1. Ceiling 4 Height Range Hood oo Te OPERATION TEST Min 61 cm 24 in Max 76 2 cm 30 in Appox 91 4 cm 36 in Before permanently mounting the range hood temporarily wire the range hood and test for proper operation If the rangehood is not operating correctly do not continue with the installation PREPARE HOOD LOCATION If the bottom of the cabinet is recessed add wood filler strips on each side The wood strips must be as thick as the recess Using appropriately sized wood screws attach filler strips in the locations shown Bottom View Wood Filler Strips Cabinet Bottom OUTDOOR VENTING METHODS This range hood can be top or back vented Check to see which venting method you have If this is a new installation choose which venting method suits your needs NOTE Before making any cuts or holes for installation carefully measure and mark all measurements Double check all measurement markings before cutting Cut out the openings for damper and power access hole in the cabinet bottom or exterior wall depending on the direction of venting chosen See figures below Top Venting Option Centerline 10cm 28 5cm 14 80m 28cm E __ S eg 13cm 13cm dia hole2. Measurement conversions 1 cm 3 8 in 2 8 cm 1 1 8 in 3 2 cm 1 1 4in 3 9 cm 1 1 2 in 10cm 315 16in 11 8cm 43 4in 13cm 51 8in 20cm 3 4in 28 5cm 11 1 4in Back Venting Option Al 3 m m dia hole e pl 14 13cm 13cm IMPORTANT Vent system must terminate outdoors through roof or side wall Do not terminate the vent system in an attic or any other enclosed area Use only metal flexible aluminum vents Never use plastic vents Always keep ducts clean to ensure proper air flow NEVER exhaust air or terminate duct work between walls crawl spaces ceilings attics or garages All exhaust must be vented to the outdoors Use caulking to seal exterior wall or roof opening around the cap Do not use 10 2 cm 4 in laundry type wall caps It is recommended that the range hood be vented vertically through the roof through 15 cm 6 in round metal aluminium vent work The size of the vent should be uniform Use no more than three 90 degree elbows Do not install two elbows together Make sure there are a minimum of 61 cm 24 in of straight vent between the elbows if more than one elbow is used The length of the vent system and number of elbows should be kept to a minimum for effective performance The vent system must have a damper If roof or wall cap has a damper Do not use damper supplied with the range hood Use duct tape to seal
3. 6 Ducted fans must always be vented to the outdoors A WARNING To reduce the risk of fire use only metal duct work CAUTION For general ventilation use only Do not use the range hood fans to exhaust hazardous or explosive vapours AA WARNING To reduce the risk of injury in the event of a range top grease fire observe the following Based on kitchen fire safety tips published by the NFPA 1 SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner BE CAREFUL TO PREVENT BURNS If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT 2 NEVER PICK UP A FLAMING PAN you may be burned 3 DO NOT USE WATER including wet dishcloths or towels a violent steam explosion will result 4 Use an extinguisher ONLY if a You know you have a class ABC extinguisher and you already know how to operate it b The fire is small and contained in the area where it started c The fire department is being called d You can fight the fire with your back to an exit CAUTION To reduce risk of fire and to properly exhaust air be sure to vent air outside do not vent exhaust air into spaces within walls ceil ings attics crawl spaces or garages WARNING To reduce the risk of fire or electric shock do not use this hood with any external solid state speed control device AA WARNING FOR GENERAL VENTILATION USE ONLY DO NOT USE THIS RANGE HOOD TO VENTILA
4. stainless steel range Nood odel 6540SA009STS Installation Guide and User Manual IMPORTANT Carefully check the unit prior to installation to ensure there is no damage Do not dispose of any packaging until you are satisfied with your new range hood If you have any problems with this unit or there are missing or damaged parts please call toll free 1 800 459 4409 DO NOT RETURN THE UNIT TO THE PLACE OF PURCHASE before calling the toll free number above e Read and save these instructions Save this guide for local electrical inspector s use e Approved for residential appliances e For residential use only Installation must comply with all local codes e Requirement 120V AC 60Hz 15 or 20 A Branch Circuit e Read all instructions before proceeding e Turn off power circuit breaker before wiring this appliance Installer Must leave instructions for this unit with owner Homeowner Please retain these instructions for future reference and for local electrical inspector s use IMPORTANT SAFETY INSTRUCTIONS Read all instructions before installing and operating this appliance INSTALLATION Do not install if the appliance is damaged 1 The instructions in this manual are intended for qualified installers service technicians or other qualified persons NEVER attempt to install this appliance yourself Installing the unit without an electrical and technical background could resu
5. all joints in the vent system Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape Example 1 Vertical roof venting Example 2 Horizontal wall venting Roof ca Nt Z Roof j Cabinet Cabinet Pipe Damper A Pipe Range hood Range hood Damper Wall cap Wall Ducting through the roof Ducting through the wall 15 Calculate the duct run length If ducted with the required minimum of 15 cm 6 in round duct work the duct run should not exceed 10 7 m 35 ft Calculate the length of the duct work by adding the equivalent feet as below for each piece of duct in the system If you must elbow right away do it as far away from the hood s exhaust opening as possible 45 Elbow 91 4cm 36 in 2 74 m 9 ft Straight Duct 2 74 m 108 in 90 Elbow 1 52 m 60 in 90 Flat Elbow 3 66 m 144 in 2 90 Elbow 3 05 m 120 in Wall Cap 0 cm 0 in Total System 5 79 m 228 in Wall Cap 0 cm 0 in INSTALLATION INSTRUCTIONS Before making cuts make sure there is proper clearance within the ceiling or wall for exhaust vent Check your ceiling height and the hood height before you install your range hood The hood installation height above the cook top can vary slightly A lower hood ensures more effective capture of cooking odours grease and smoke However the hood should
6. to the repair or replacement of a unit at our option that may prove by our sole examination to be defective under normal use and service during the warranty period The Company may issue credit in the amount of the invoice value of the defective product or a percentage of it according to use in lieu of repair or replacement All replace ments FOB Quality Craft Ltd nearest service depot Quality Craft Ltd warranty is non transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacture s specifications This warranty shall not apply to any product that has been subject to accident alteration misuse abnormal chemical condi tions This warranty is made in lieu of all other warranties expressed or implied No other warranty expressed or implied is assumed or will be assumed Imported by Quality Craft Kitchen amp Bath Ltd 5 2436 Industriel Blvd Laval Quebec Canada H7S 2G7 TOLL FREE TEL 1 800 459 4409 www qualitycraft com Made in China
7. warnings PERSONAL INJURY HAZARD Because of the weight and size of the range hood two or more people are needed to move and safely install the range hood Failure to properly lift range hood could result in damage to the product or personal injury All openings in ceiling and wall where range hood will be installed must be sealed Range hood location should be away from strong draft areas windows doors and strong heating vents SEVERE INJURY Rotating fan can cause severe injury Stay clear of fan when motor is running SEVERE INJURY Range hood may have very sharp edges Please wear protective gloves to remove any parts for installing cleaning or servicing DIMENSIONS 29 8 in MEASUREMENTS This product is designed for under cabinet installation Before installation measure all distances to ensure the proper position of the range hood 1 Distance from the floor to the ceiling 2 Distance between the floor to the counter top stove 3 Distance between the counter stove and range hood 61 cm to 76 2 cm 24 in to 30 in For optimal performance the range hood should not be installed more than 76 2 cm 80 in from cooktop 4 Height of cabinet 5 Height of the range hood installation location 6 Determine if your existing venting system is top or back venting before any installation begins DO NOT INSTALL CLOSER THAN 61 CM 24 INCHES ABOVE COOKING SURFACE
8. 0mm pm 2 TL TOP VIEW asn i J i 20mm f 10mm DW 250mmi 9 13 16 in Ge in zorim A in i d 80mm 3 1 8 ni e 26 BACK VIEW 757mm 29 13 16 in i Damper ED Control Switch Hood body i co i n Bottom Panel Aluminium Filters 27 1 YEAR HOME USE WARRANTY This product is warranted to the original purchaser to be free of defects in material and workmanship for one 1 year from the date of purchase This warranty does not extend to commercial or institu tional use or installation Warranty service should be arranged through the point of purchase The purchaser is responsible for transporting the unit to and from the point of purchase Incidental repairs that would involve a minimum of time and effort on behalf of the purchaser will not be considered warranty work and no compensation will be deemed forthcoming Any failure of the unit that is not traceable to a defect in material or workmanship is not covered by this warranty These non warrant able items include but are not limited to e Change in colour or finish due to chemical usage e The use of abrasive cleansers e Improper maintenance resulting from failure to reasonably clean care for or maintain a product in ac cordance to Quality Craft s cleaning instructions e Unit not properly installed in accordance with manufacturer s instructions e Damage caused during shipping handling or installation e Operating maintenance safet
9. OLS FOR INSTALLATION CS powered ili i screwdriver utility knife or drill measuring tape flat blade gd screwdrivers Q adjustable marker or s wrench Philips H H screwdrivers needle nose hammer pliers Notice 1 Remove the range hood from the carton packaging and place on a flat surface for assembly 2 Check carefully to ensure there are no missing parts or mounting hardware 3 When installing cleaning or performing maintenance it is recommended wearing safety glasses and safety gloves 4 AA WARNING To avoid danger of suffocation keep the plastic that covers the unit away from children Do not use in cribs beds carriages or playpens The bag is not a toy Discard bag and all other packing materials immediately after removing the unit Do not reuse the bag SUPPLIED PARTS Description Range Hood with 2 filters Damper located inside the hood 04 mm x 8 mm tapping screw 065 mm x 30 mm tapping screw Installation Guide installation guide 65 mm x 30 mm tapping screw x 4 k 4mm x 8 mm tapping screw x 2 DU damper x 1 range hood x 1 11 12 PLANNING FOR INSTALLATION AWARNING Proper installation is your responsibility Have a qualified technician install this range hood Read the entire installation guide and user manual thoroughly and understand instructions and
10. RVE ALL GOVERNING CODES AND ORDINANCES IMPORTANT It is the customer s responsibility to contact a qualified electrical installer and assure that the electrical installation is adequate and complies with the National Electrical Code or CSA standards and all local codes and ordinances AWARNING Electrical grounding is required for this range hood Check with a qualified electrician if you are not sure whether the range hood is properly grounded Failure to follow electrical requirements may result in a fire A fuse in the neutral or grounding circuit could result in electrical shock If the hot cold water pipe is interrupted by plastic nonmetallic gaskets or other materials DO NOT use for grounding DO NOT ground to a gas pipe 1 Save installation instructions for electrical inspector s use 2 If codes permit and a separate ground wire is used it is recommended that a qualified electrician determine if the ground path is adequate 8 DO NOT use an extension cord or adapter plug with this appliance 4 RISK OF ELECTRICAL SHOCK This range hood must be properly grounded 5 The range hood must be connected with copper wire only 6 The range hood should be connected directly to the junction or circuit breaker box through flexible armoured or nonmetallic sheathed copper cable Allow some slack in the cable so the appliance can be moved if servicing is ever necessary 7 A UL listed or CSA approved conduit connector
11. TE HAZARDOUS OR EXPLOSIVE MATERIAL AND VAPOURS TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE 1 Never leave range unattended when in use 2 Boil overs cause smoking and greasy spillovers that may ignite 3 Heat oils slowly on low or medium setting 4 Always turn hood ON when cooking at high heat or when cooking flaming foods i e Crepes Suzette Cherries Jubilee Peppercorn Beef Flambe 5 Clean ventilation fans frequently 6 Grease should not be allowed to accumulate on fan or filters 7 Use proper pan size 8 Always use cookware appropriate for the size of the surface element To get the best performance the vertical clearance between the cook top and the range hood should range from 61 cm 76 2 cm 24 in to 30 in GROUNDING INSTRUCTIONS This appliance must be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current A WARNING Improper grounding can result in a risk of electric shock Consult a qualified electrician if the grounding instructions are not completely understood or if doubt exists as to whether the appliance is properly grounded CAUTION The range hood has a thermally protected system for the motor which will shut down automatically if the motor is overheated If the overheat protection trips disconnect the power and wait for 10 minutes until the motor cools down ELECTRICAL REQUIREMENTS OBSE
12. abinet Check to ensure all 4 screws are situated in the narrow portion of the keyholes Test the damper blade to ensure it rotates up and down freely figure 8 Keyhole neck Keyhole slot WARNING ENSURE THE RANGE HOOD IS SECURELY ATTACHED TO THE CABINET BEFORE RELEASING 10 Connect vent work to hood and seal joints with duct tape ensuring an air tight fit When cutting or drilling into walls or ceilings do not damage electrical wiring and hidden utilities 20 12 11 Connect the electrical wires from the range hood to the house wiring Make sure you read and understand the electrical requirements section at the beginning of this manual A WARNING All wiring should be done by or approved by a qualified electrician Before doing any electrical work make sure wires do not slip between any moving parts to prevent any damage Install the bottom panel and aluminium filters Fig 9 Ensure the holes beside the fan guard align with the holes on the bottom panel before inserting screws Turn the power on and check all lights and fan operation MAINTENANCE Prior to any maintenance operation ensure that the range hood is discon nected from the power supply AWARNING ELECTRICAL SHOCK HAZARD Do not perform service on an electrically live system Disconnect the main electrical supply before servicing this device Touching electrical connectors or other exposed electrical circuitry insid
13. appen if the instructions are not followed This safety alert symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and the word WARNING AA WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING CAREFULLY 1 Use this unit only in the manner intended by the manufacturer If you have any questions contact the distributor importer or the manufacturer 2 Before servicing or cleaning the unit switch power off at the junction box and lock the panel door to prevent power from being switched on accidentally If the junction box door cannot be locked securely fasten a prominent warning sign to the panel door 8 Installation work and electrical wiring must be done by qualified person s in accordance with all applicable codes and standards including fire related construction 4 Sufficient air is needed for proper combustion and exhausting of gases through the flue duct cover of fuel burning equipment to prevent back drafting Follow the heating equipment manufacturer s guidelines and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and the local code authorities 5 When cutting or drilling into the wall or ceiling do not damage electrical wiring and hidden utilities
14. be installed a minimum of 61 cm 24 in and a maximum of 76 2 cm 30 in above the range top Screws are provided to secure the range hood to most types of cabinets You should consult a qualified installer to verify that the supplied screws are suitable for your cabinets The manufacturer assumes no responsibility for injury and or damage caused by improper installation Put a thick protective covering over your counter top cook top or range to protect from damage and dirt Remove any hazardous objects around the area when installing A WARNING TURN OFF ALL POWER Ensure all power is turned off at the main electrical box before commencing installation TURN OFF ALL GAS If you are installing above a gas range the gas must be turned off at the source 1 Determine the venting method vertical top venting or horizontal back venting 2 Use a hammer and flat tipped screwdriver to gently punch out the appropriate electrical knock out hole figure 1 Be very careful not to leave any broken pieces inside the range hood Electrical knock out hole 8 Using a flat tipped screw driver or needle nose pliers remove the appropriate knock out for your installation type fig 2a or Fig 2b Top Venting Back Venting Fig 2 17 Top Venting Back Venting S Fig 2 4 Install the damper with two 4mm x 8mm tapping screws figure 3 If this hood replaces an existing unit the location of the ai
15. e this range hood when they are energized could result in death serious bodily injury or property damage Cleaning range hood surface The range hood should be cleaned regularly internally amp externally in order to preserve its fine appearance and optimal level of operation Always clean in the direction of orginal polish lines Always rinse well with clean water two or three times after cleaning Wipe completely dry with a soft non abrasive cloth Clean periodically with hot soapy water and a clean cotton cloth After cleaning you may use non abrasive stainless steel polish cleaner to polish Always rub lightly and with the grain Make sure the ducting system is free of debris DO NOT let plaster dust or any other construction residue enter the hood During construction or renovation cover the hood DO NOT use corrosive or abrasive detergents steel wool or scouring pads These will scratch and damage the stainless steel surface DO NOT allow deposits to remain for long periods of time Rinse with water after exposure and wipe dry with a clean cloth DO NOT leave the hood unclean for long periods or allow dirt to accumulate Detergents DO NOT use corrosive or abrasive detergents or any products containing chloride fluoride iodide bromide to the product as it will deteriorate the surface rapidly DO NOT allow cleaning compounds salt solutions disinfectants or bleaches to remain in contact wit
16. h the product for extended periods Any combustible products used for cleaning such as acetone alcohol ether benzol etc are highly explosive and should never be used close to a range 22 Cleaning aluminium filters The filters fitted by the factory are intended to filter out residue and grease from cooking It need not be replaced on a regular basis but are required to be kept clean Do not accumulate oil over 80 of the filter surface to avoid oil dropping on range The filters must be cleaned once a month using non abrasive detergents either by hand or in the dishwasher Set dishwasher to a low temperature and a short cycle setting When washed in a dish washer the grease filter may discolour slightly but this does not affect its filtering ability Dry filters and re install before using hood A WARNING Failure to carry out the basic standards of cleaning of the range hood and replacement of the filters may increase the risk of fire We therefore recommend that you follow these instructions Replacing Filters Should filters wear out due to age or prolonged use replace with an aluminum grease filter with stainless steel clips Note Also replace a damaged filter that has punctures or a bent or broken frame Replacing light bulbs AWARNING BURN HAZARD Light bulbs can become extremely hot when turned on DO NOT touch bulb until switched off and cooled Touching hot bulbs could cause seri
17. joints are properly connected sealed and taped Make sure the power is on high speed for heavy cooking Wind from opened windows or doors in the surrounding area are affecting the ventilation of the hood Close all windows and doors to eliminate the outside air flow Check if the direction of duct opening is against the wind If so adjust the direction of the duct opening Check if the wrong size of ducts are being used 6 The light does not work Check to see if light bulb is loose If so tighten Remove problem bulb and insert one you know is working If the properly functioning light does not come on the problem may be the light assembly Service or replace the light assembly 25 NOTE For all other inquiries please contact us 1 800 459 4409 WIRING DIAGRAM Yellow amp Green Capacitor Du F 370V MAX 25W JDR 16 GU10 Light Black gl ZS Se White rel e Black Black lt if White ZDSS SES u3319 9 MOJI A a r Grey SPECIFICATIONS E 757mm 29 13 16 in 706mm 27 3 4 in ea E E 28mm 290mm 9 13 16 in zS 1 1 4 in 22mm 7 8 in 39mm Li i dia hole 1 1 2 in i KE 18mm 1 g 1116 in FE Jegen 3 1 8 n z 93 5mm 3 11 16 in S i 5 leo 5
18. lt in injury All electrical wiring must be properly installed insulated and grounded Old duct work should be cleaned or replaced if necessary to avoid the possibility of a grease fire Check all joints on duct work to ensure proper connection All joints should be properly taped Personal injury hazard Because of the weight and size of the range hood two or more people are needed to move and safely install the range hood Failure to properly lift range hood could result in damage to the product or personal injury SEVERE INJURY Range hood may have very sharp edges Please wear protective gloves to remove any parts for installing cleaning or servicing DO NOT INSTALL CLOSER THAN 61 CM 24 INCHES ABOVE COOKING SURFACE OPERATIONS Read all instructions in this manual before operating the appliance Always leave safety grills and filters in place Without these components operating blowers could catch on to hair fingers and loose clothing NEVER dispose of cigarette ashes ignitable substances or any foreign objects in blowers NEVER leave cooking unattended Use caution when cooking with oil Overheating may cause oil to reach its flash point and ignite Used oil will ignite at lower temperatures than fresh oil NEVER cook over open flames under the range hood Constantly monitor deep fryers during use as overheated oil may ignite CLEANING Do not operate blowers when filters are rem
19. must be provided at each end of the power supply cable at the range hood and at the junction box 8 When making the electrical connection cut a 3 2 cm 1 1 4 in hole in the wall A hole cut through wood must be sanded until smooth 8 A hole through metal must have a grommet 9 When cutting or drilling into the wall or ceiling do not damage electrical wiring and other hidden utilities 10 Wire sizes must conform to the requirements of the National Electrical Code ANSI NFPA 70 latest edition or CSA Standards C22 1 94 Canadian Electrical Code Part 1 and C22 2 No 0 M91 latest edition and all local codes and ordinances 11 Connect Black to Black White to White and Green to Green wires from the range hood to the house wiring and cap with wire connectors Range hood wiring BLACK Live WHITE Neutral GREEN YELLOW Ground Wiring from electrical source White N AWARNING ELECTRICAL SHOCK HAZARD Do not perform service on an electrically live system Disconnect the main electrical supply before servicing this device Touching electrical connectors or other exposed electrical circuitry inside this range food when wey are energized Coua resu National Fire Protection Association Batterymarch Park Quincy in death serious bodily injury or property Massachusetts 02269 CSA International 178 Rexdale Boulevard Toronto Ontario CANADA M9W 1R3 10 LIST OF MATERIALS TO
20. operly connected Check that the power connection for the unit is properly connected Make sure the wiring between the switch board and control board are connected properly 2 The range hood vibrates when the blower is on The range hood might not have been secured properly to the wall Check if the motor is secured in place If not then tighten the motor in place Check if there is a damaged blower wheel If so change the blower wheel 3 The blowers seems weak Check that the duct size used is at least 15 2 cm 6 in Range hood WILL NOT function efficiently with insufficient duct size For example 17 8 cm 7 in duct cover 15 2 cm 6in holes and loosely secured Check if duct is clogged or if damper unit is not opening properly A tight mesh on a side wall cap unit might also restrict air flow 4 The lights work but the blower is not spinning is stuck or is rattling The blower might be jammed or scraping the bottom The motor is defective possibly seized change the motor The thermal protection system detects if the motor is too hot to operate and shuts the motor down In this case the motor will function properly after the thermal protection system cools down approx 10 min 5 The hood is not venting properly Make sure the distance between the cook top and the bottom of the hood is between 61 cm 24 in and 76 2 cm 80 in Reduce the number of elbows and length of duct work Check if all
21. ous burns SEVERE INJURY Rotating blower fan can cause severe injury Stay clear of fan when motor is running WARNING Disconnect range hood from electrical source and be sure lights are cool Should the light bulb burn out due to age or prolonged use replace with MAX 25W JDR 16 GU10 twist and lock base lamps If new lights do not operate make sure the light bulb is inserted correctly 23 1 Turn off the range hood 2 Ensure the lights are cool to the touch 3 Turn bulb anti clockwise to remove 4 Install anew GU10 twist and lock base lamp MAX 25W JDR 16 and turn clockwise to install the light bulb Do not release the bulb until you sen Je are sure the bulb has been securely installed A Rotate anti clockwise gt and pull out to remove Power Switch Low Speed Medium Speed High Speed Light Switch OPERATION TURN ON 1 Press the speed control switch Low Speed Medium Speed High Speed to select the desired level of power Once a button is pressed the previous speed mode will be canceled 2 Press the Light Switch to turn on the lights TURN OFF 3 Press the Power Switch to turn off the power fan only 4 Press the Light Switch to turn off the lights Note The fan and the lights are operated independantly of each other TROUBLE SHOOTING 1 If the range hood does not operate after installation Check if all power has been turned back on and all electrical wiring 24 is pr
22. oved 1 The saturation of greasy residue in the blower and filters may cause increased flammability Keep this appliance clean and free of grease and residue build up at all times to prevent possible fires 2 Filters must be cleaned periodically and kept free from accumulation of cooking residue see cleaning instructions inside Old and worn filters must be replaced immediately 3 NEVER disassemble parts to clean without proper instructions Parts should be disassembled by qualified persons only The manufacture and distributors decline all responsibility in the event of failure to observe the instructions given here for installation maintenance and suitable use of the product The manufacturer and distributors further decline all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance Workman Safety Gloves Se SAFETY NOTE Remove PVC film before installation Always wear Workman Safety Gloves for installation cleaning light bulb replacement and dismantling to reduce the risk of injury READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START It is very important for your safety and the safety of others that you follow the many important safety messages in this manual and on your appli ance Always read and obey all safety messages All safety messages will tell you what the potential hazard is how to reduce the possibility of injury and what can h
23. r exhaust can vary from one manufacturer to another Make sure the damper fits in the existing opening before installing Top Venting Option Back Venting Option Above the Steel Under the Steel 2x oX4mm x 8mm screws A 2x oX4mm x 8mm screws 18 5 Seal the damper to the hood using duct tape figure 4 6 Turn the hood upside down ona protective covering such as card board or a large towel Remove the 2 aluminum filters and bottom panel a Remove the aluminum filters by pulling the handles b Remove the bottom panel by removing the 6 screws figure 5 c Ensure you have a good grip on the bottom panel when removing the screws so it does not fall into the unit 7 Lift the range hood up under cabinet and determine final position Mark the location of the four keyhole mounting slots Set range hood aside on a protected surface figure 6 Drill 4 pilot holes in the marked positions Keyhole slot Drill pilot hole 8 Screw the four 5 mm x 30 mm tapping screws into the pilot 7mm holes Leave screw heads about i 0 28 in 7 mm 0 28 in from the cabinet surface figure 7 Fig 7 9 Lift range hood into position feeding electrical wires through wiring opening Position the range hood so the large end of the keyhole slots are over the screws Push the hood toward the wall so the screws are in the neck of the slots Tighten the screws to secure the range hood to the c
24. y guidelines not being followed e Any alterations to the unit e Damage to the unit as a result of accidental impact fire flood freezing normal wear e Light bulbs are not covered by this warranty e Scratches chips cracks or holes caused by shipping storage or installation A thorough inspection must be made at time of pick up or delivery If the unit is damaged a Claim must be made with the carrier Report any damage promptly and prior to installation Quality Craft Ltd will not be held liable for any freight damage or damage caused by leaks due to freight damage Inspection prior to installation is the responsibility of the installer contractor or user Quality Craft Ltd will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing Quality Craft Ltd will not be held liable for damages resulting from the improper fit or installation of products not supplied by this company Quality Craft Ltd will not be held liable for loss of use of unit inconvenience costs incurred for labour materials removal and installation of replacement units or any other incidental or consequential damages Costs relating to obtaining access for repair or replacement are the responsibility of the user Under no circumstance shall Quality Craft Ltd or any of its representatives be held liable for injury to any persons or damage to any property Quality Craft Ltd s obligations shall be limited
Download Pdf Manuals
Related Search