LKS-SH5P, LKS-SH8P Manual
Contents
1. Standards IEEE802 3 10Base T Ethernet IEEE802 3u 100Base TX Fast Ethernet Protocol CSMA CD 10Base T Cat 3 UTP or above N k 0 100Base TX Cat 5 UTP or above Speed Half Full Duplex 10 20Mbps 100 200Mbps Transmission Method Fast store and forward MAC Address Table 1K LKS SH5P 1K LKS SH8P Packet Filtering 14880pps 10Mbps per port Forwarding Rate 148800pps 100Mbps per port Backplane Bandwidth 1Gbps LKS SH5P 1 6Gbps LKS SH8P AC Power Supply AC 100 240V 50 60Hz DC Input DC 9V 600mA Power Consumption 2 7W LKS SH5P 4 2W LKS SH8P Dimension W x D x H 5 5 x 3 6 x 1 3 in 140 x 90 x 32 mm Operating Temperature 32 F 104 F 0 C 40 C Storage Temperature 40 F 158 F 40 C 70 C Operating Humidity 10 90 RH non condensing Storage Humidity 5 95 RH non condensing Certifications FCC Part 15 Class B CE Mark Class B FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a p2. LED indicators of the switch along with explanation of each indicator 2 Installation Description This indicates that the switch is power on Please check the DC power adapter to ensure the adapter is installed properly and attached to the switch Link Act Blinking The connection is successfully established with the end node The port is transmitting or receiving data packets 2 1 Before Connecting to the Network Before connecting the LKS SH5P LKS SH8P to the network please pay attention to the following instructions V V V 2 2 Connecting to End Nodes Use standard CAT5 Ethernet cable to connect the switch to end nodes as Do not put heavy articles on the switch Check the power adapter to confirm the secure connection Make sure there is adeguate space for proper heat dissipation and adequate ventilation around the switch described below Switch ports will automatically adjust to the characteristics cable type speed duplex mode of the device to which is connected null0nl00l0n O End node Connecting to an end node Please refer to the LED Indicator Specifications 2 3 Connecting to Router or Switch Internet Cable DSL Modem Router LINESEET wan IER604 TF v LES SHSP LES SHSP v 6 w Server Connecting to router or switch Please refer to the LED Indicator Specifications 3 Product Specification
3. P is perfect choice for home and small office use 1 1 Switch Features gt Complies with the IEEE802 3 10Base T Ethernet IEEE802 3u 100Base TX Fast Ethernet standards gt Supports NWAY auto negotiation function Half Full duplex auto detect data transfer rate gt Provides 5 8 10 100Mbps auto sensing RJ45 ports and supports auto MDI MDI X gt Supports IEEE802 3x flow control for Full duplex and Backpressure flow control for Half duplex gt Supports non blocking line speed forwarding gt Supports store and forward switching method 1 2 Package Contents Please check the articles carefully after you open the packing as below M One LKS SH5P LKS SH8P Fast Ethernet Switch M One Power Adapter M One User Manual If any of the listed items are missing or damaged please contact the local reseller from whom you purchased for replacement 1 3 Front Rear and Side Panel Specifications The front panel of LKS SH5P LKS SH8P Fast Ethernet Switch includes Link Act indicators and one Power indicator Please refer to the detailed description of these indicators in LED Indicator Specifications The rear panel of the switch includes 5 8 10 100Mbps RJ45 ports The side panel of the switch includes one DC power port used for DC power input 1 4 LED Indicator Specifications The LED indicators of the switch include Power and Link Act You can see their operating situation through these LED indicators The following chart shows the
4. articular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help L KKSKEV TECHNICAL SUPPORT E maitbtitech linkskey com Website www linkskey com
5. ske DBS A LKS SH5P LKS SH8P 5 8 Port Fast Ethernet Switch User Manual Rev 1 0 Contents 1 Introduction aaaa aaa aa aaaaanononaaa aa aaa 2 1 1 Switch Features ee 1 2 Package Contents re 1 3 Front Rear and Side Panel Specifications 1 4 LED Indicator Specifications 2 Installation ennn 4 2 1 Before Connecting to the Network 2 2 Connecting to End Nodes 2 3 Connecting to Router or Switch 3 Product Specification 22200 50 1 Introduction LKS SH5P LKS SH8P is a 10 100Mbps Fast Ethernet mini desktop switch It is especially designed for SOHO student dormitory and small group users It has 5 8 10 100Mbps Auto negotiation Ethernet ports and supports auto MDI MDI X The Auto negotiation on each RJ45 port senses link speed 10 100Mbps and duplex mode full half duplex mode of its link partner and adjust itself for optimal performance With support of auto MDI MDI X it eliminates the hassle of choosing the right kind of cable The LKS SH5P LKS SH8P is easy to install Plug and Play function helps you setup and be connected in no time Just plug in the power adapter and connect your PC with an Ethernet cable to the switch and you are ready LKS SH5P LKS SH8
Download Pdf Manuals
Related Search