DeeGreen User Guide
Contents
1.2. Add object button O Copy an already added model using Copy button O Move scale and turn the object All changes can be reversed using Undo button or can be discarded using the Remove button Every model must stay on the platform level and must not get underneath it It can be done so using the Fix button Before proceeding to the printing task the model must not hang over the edge When ready to print push the green button to begin the printing On the printer screen 1 Step 1 Check the filament string type choose the type the model will be printed with The printer can use PLA PVA and Wood filaments only If the settings don t meet the reality the filament is not attached to the printer check the printer is connected to the computer and choose Change the string button If a different filament string is attached please remove it following the instructions wait until the string is released only then you will be able to completely remove it When putting a new string into the printer please follow the instructions further in this User Guide Select required print quality The print quality will define the wall thickness of each layer of the printed model fast print 0 2 mm med quality print 0 15 mm high quality print 0 1 mm Should your model need supports please confirm it by ticking this option a support is auxiliary construction that allows printing of overhanging models e g bridges When ready
3. click on the Proceed button 2 Step 2 This step prepares and initiates the print task if not connected to the computer the GCO file is to be copied onto SD card When connected to the computer DeeControl will copy prepared print task to the printer memory and will begin platform heating its calibration and the print itself fully automatically 3 Step 3 You will be informed about the current print task status at this stage 16 DeeGreen User Guide 11 Printer menu scheme selection a S od string bed parking other e language selection 12 Cleaning and support A Keep the axis rods oiled see chapter 14 A Maintain the print area clean and off the filament remnants Clean the print area after every print task 13 Filaments and spare parts Filaments and selected spare parts can be ordered at your supplier or via be3d website 14 Warranty terms amp conditions DeeGreen 3D printer warranty Defect product liability law The law is in accordance with the latest Czech lawsuit regarding product defect responsibility Quality warranty is not covered by this law Mechanical parts are covered by the warranty for the term of 24 months since the purchase has been made This warranty covers any unintended mechanical failures or malfunctions caused by either manufacture procedures or flaws that might have occurred during montage procedure The warranty does not cover misuse or inappropriate usage inadequate manip
4. lighting Printable material Power source External dimensions Weight Inputs 3 Safety instructions Warranty void if damaged due to not following the instructions in this User Guide 1 Damage caused by improper use in contradiction with this User Guide or violating the security instructions are the full responsibility of the user 2 This device operates at high temperatures extreme caution must be used 3 This device is not suitable for children and must be operated by persons over the age of 18 in all other instances the supervision of an adult is required 4 The device must not be left unattended whilst in operation 5 Some parts of the printer operate at temperatures greater than 70 C Danger of burning 6 Handicapped people who are not able to fully operate the device must have be supervised by a technically qualified person 7 Make sure the product is complete before using 8 Danger of electric shock if not operated correctly 9 Disposal of the device must be performed using the correct environmental considerations 10 Install the printer in a place which is A A Dry and free from dust A Astable environment temperature humidity A Well ventilated A Close to an easily accessible electrical supply A Ata sufficient distance from the objects that could cover the ventilation holes of the printer A Ata sufficient distance from objects susceptible to heat e g curtains and drapery also from splashing liqu
5. task is complete allow a few minutes to printer to cool down between the tasks or before shutting down the printer Use extra caution when manipulating with the filament spool put the string end through the spool hole so an unwanted accidental roll back can be avoided DeeGreen User Guide 9 DeeControl software installation DeeControl setup file can be found on the provided CD in deecontrol setup exe location Once launched the setup wizard will guide you through the installation process Welcome to the DeeControl Setup Wizard This will install DeeControl version 0 8 0 on your computer It is recommended that you dose all other applications before continuing Click Next to continue or Cancel to exit Setup Select Destination Location Where should DeeControl be installed k Setup will install DeeControl into the following folder To continue click Next If you would like to select a different folder click Browse Atleast 144 2 MB of free disk space is required lt td ee Choose the software location and click on Next to proceed DeeGreen User Guide Select Start Menu Folder Where should Setup place the program s shortcuts Setup will create the program s shortcuts in the following Start Menu folder To continue cick Next If you would like to select a different folder click Browse lt Back Net Cave You may change the location name that will be displayed in Start menu Click
6. 200 print hours Instructions stated in this User Guide were ignored Other but recommended filaments were used Printer electronics were altered User owner has financial commitments to the seller or manufacturer The printer was damaged due to inappropriate usage or due to inadequate manipulation during transportation or keeping the printer in wrong climate conditions esp inadequate temperature and humidity The warranty is void when printer electronics and control units are damaged due to atmospheric events such as thunderstorm power network overcharge pollution and damage of mechanical chemical or heat character as well as repairs alternations or modifications by unauthorized service centre or user 15 Authorized service interventions Authorized service interventions are allowed only when complied exactly with either instructions provided in this part of User Guide or with spare parts if received Placing new filament string A gt gt gt z Release the string following instructions on printer screen Remove the released string manually Cut off the string end and straighten last 5 cm 1 96 The string must not be bent Put the string to the input hole Push the string gently as far as possible until it will not go further Do not apply pressure or force Finish the procedure following instructions on the printer screen until the part when automatic roll is initiated push the string gently toward the printer Visu
7. Installation and service instructions warranty terms amp conditions DeeGreen User Guide DeeGreen User Guide 10 11 12 13 14 15 16 DeeGreen User Guide 1 Content CONTEN ar E E E EN E E E EE E E TEE E EEE E E E E E EE 3 WTS Merz ETT TITTTIET TT ny stecoaceasteunntea sete ding eas anaes NEEE ANNEANNE EEEE ESNA s 4 Safety Ua IC i o RINT TETTE E E m 4 MISI SEA CIRIE NP TO Em 5 Parts IOS C I EON NE eerie OT Eoo Emme 5 PIC WASTING c TT 7 Bici pega DAP RC NEU mme 7 Getting the printer to operate RE E T OT OL TL om E 7 DeGCOnercl SortWale Trist Ia BIO ac comuna assa sas te vsque asque E EE 8 Deer oDEEOT operatio on opina apa Odeon deferebat ram fpe ee ee DN a ND ND NM NNUS DN DUE 14 Printer mend Scheme ee eer Tt tr rT ett ret ter tt eet te ee er et tT 17 Cleaning and SU STET COT 17 Filame ntsand spare palts estt een xke seed ro EUER EEE EEE titii nete MPa ses ETEEN Ea dq 17 Warranty terms CORTE POTES rrr rennan aE qr ONU n EAE E ARAE EAEE PEN IV III EIE AEE EA 17 Authorized service interventions RENT IT OO T T 18 Contact details mer 19 DeeGreen User Guide 2 Technical parameters Printing technology Printing area Pront accuracy Layer thickness Nozzle diameter Print speed Printer control Interior
8. PORT Download directx from this url address http www microsoft com en us download details aspx id 8109 Or install it from installation CD This error will show if there is no DirectX for 3D installed on your computer Click on the provided link to download the latest version of DirectX or you can install it from the provided CD 11 DeeGreen User Guide Installation of the software for 3D imaging support DirectX June 2010 SDK Le E Please read the following license agreement Press the PAGE DOWN key to see the rest of the agreement MICROSOFT SOFTWARE LICENSE TERMS MICROSOFT DIRECTX SOFTWARE DEVELOPMENT KIT SDK These license terms are an agreement between Microsoft Corporation for based on where you live one of its affiliates and you Please read them They apply to the software named above which includes the media on which you received it if any The terms also apply to any Microsoft L updates D supplements Intemet based services and support services for this software unless other terms accompany those items If so those terms apply BY USING THE SOFTWARE YOU ACCEPT THESE TERMS IF a Do you accept all of the terms of the preceding License Agreement If you choose No Install will close To install you must accept this agreement Once read click on Yes to agree with the license agreement DirectX June 2010 SDK Lor fat Please type the location where you want to
9. ally check if the string is pulled in and complete the guide when the melted filament is released off the nozzle Bt Printing string 18 DeeGreen User Guide Moving rods lubrication A A gt z z Select Settings option in the printer menu and park the printer Switch off the printer and disconnect the power supply Take down the printer s top cover Unscrew all four screws in the rear printer cover Remove the cover using 3mm L key Do not touch any electronic or electrical parts nor any cables Lubricate the moving rods with a thin layer of oil low viscosity oil is recommended Put a thin layer of grease onto the trapezoidal screw grease resistant to temperatures above 100 C is recommended Once finished return the rear cover to its original position and secure it with screws Use extra caution while putting the cover back pay extra attention to avoid pinching pull out or damage of electronics Turn the printer on and initiate calibration Check all axes visually There must be no extra oil or grease left on the rods The rods must not make any sound the only noise you should hear can come from engines 16 Contact details Manufacturer DO IT s r o ID 493 56 593 Contact address Pod H jkem 1 Prague 8 180 00 Czech Republic Invoicing address Pod H jkem 1 Prague 8 180 00 Czech Republic Email help be3d cz Web www be3d cz Changes and print errors right is reserved 19
10. e es ey d EM er n Open the box and take out all accessories carefully remove all protective parts Take out the printer Put the printer onto a solid and flat place e g a desk Open Main door grab top cover edge and remove it Remove the foam protection from printing head Unpack the printing platform packed among accessories and place it inside the printer on the spikes Place the printing material holder inside the printer Install the software provided on the CD following instructions in this User Guide see 8 Connect the printer to the power supply and the computer via USB cable Turn on the printer on the rear side see the picture in chapter 5 Prior to the first printing Unpack the printing material spool Find the string end and cut it 1 cm 0 39 off the end and then break it Should you not have the printing material just yet you can place an order at www be3D cz The printer is designed to work with PLA PVA a Wood 1 75mm only Under no circumstances do NOT use any other material but the recommended ones Insert the string following the instructions in the chapter 15 Press Settings option on the touchscreen and then String change Make sure the glue is applied linearly over the platform Prepare your digital model in DeeControl software Follow the instructions either from the display or DeeControl and start the printing Automatic platform calibration will be performed prior to the printing Once the print
11. ids and organic gases e g ammonia A Out of direct sunlight A Without abrupt temperature changes A Ata sufficient distance from heating vents ventilation and air conditioning systems E ce DeeGreen User Guide 4 Package content 3D printer DeeGreen Power supply 24V 5A USB cable SD card Printing material holder CD with DeeControl software Glue DeeGlue for printing platform Palette knife for printing platform cleaning and model removal eo es se de SOP do User Guide 5 Parts description AXIS X Touchscreen SD card socket Space for printing material Main door to the printing area DeeGreen User Guide Printing Head Nozzle Printing Platform Ecc Touchscreen SD card socket EN SD card Power connector lis OE NN USB connector BEEN 1 1 ON OFF Switch DeeGreen User Guide 6 Print instruments DeeGlue special stick glue increasing model adherence to print Palette knife serves to printed model removal and printing platform cleaning gt gt gt 8 DeeGreen operating requirements Supported Operating Systems Windows 7 or later DirectX 10 OpenGL compatible with Windows XP amp Windows Vista OS X version 10 7 or later Minimum HW requirements CPU frequency 2 0 GHz RAM 2 GB 500 MB HDD free space USB slot or SD card reader Getting the printer to operate Prior to the first time us
12. ing Components Searching for updated Directs Runtime Components and updating as necessary This may take a few minutes Copying Files 1 0 2905 D Microsatt Direct Direct3D The DirectX installation is running now 13 DeeGreen User Guide Installing MlicrosoftiRy Dire cexXTR Installation Complete Microsoft DirectX The components installed are now ready for use Software Development Kit The installation is now complete Click on Finish 10 DeeControl operation a Screen description gt DeeControl File RECENTLY OPENED FILES Agate E Open file amp prase p kelimek stl i from the Interner p octopus stl metropolis stl LY Do not show again Welcome screen 14 DeeGreen User Guide gt DeeControl H EC File not connected reset camega warm up settings CONTINUE N A OBJECTS 5 DW st of currently ILLS loaded models eT uen i i as US SN be3d2 scree UL Gd M C EN Aa Se v qei x e 3 tot Ti hdi M dd V 3 P AC mw awe X A si LOCATION i Sea Name The modelfor s NS Nose X Y z printi j j Xr XN ON ed Position 28 96 2759 0 00 N P Rotation 0 0 S CN Magnificatior v 1 00 100 1 00 KON N a Parameters a the Dm copy BY inito ote the MX N place on desktop 14 l Ne s reset changes A 1 x T DELETE L e N Nae DELETE A P rr 4 AA A7 sa ea IX d tinting p m
13. on Next to proceed Select Additional Tasks Which additional tasks should be performed Select the additional tasks you would like Setup to perform while installing DeeControl then dick Next The installation guide can create a desktop shortcut Click on Next to proceed DeeGreen User Guide Ready to Install Setup is now ready to begin installing DeeControl on your computer Click Install to continue with the installation or dick Back if you want to review or change any settings Destination location C Program Files x86 DeeControl Start Menu folder DeeControl Additional tasks Create a desktop icon You can check the installation configuration here Click on Next to proceed Installing Please wait while Setup installs DeeControl on your computer C Program Files x86 DeeControllapp css string css W The software is now being installed on your hard drive 10 DeeGreen User Guide Setup DeeControl Completing the DeeControl Setup Wizard Setup has finished installing DeeControl on your computer The application may be launched by selecting the installed icons Click Finish to exit Setup SAREE EERE EERE EERE EE EERE EEE E EERE EEE E OED errr re Finish The installation is finished You may now launch the DeeControl application Click on Finish to close the window Possible complications during the first launch 7 DeeControl t xm LACK OF 3D SUP
14. place the extracted files CAINS TALL Choose the software destination folder Installing Microsoft R Dire cexiR Welcome to setup for DirectX b Microsoft X FE The Directs setup wizard guides you through installation of tX Directs Runtime Components Please read the following A license agreement Press the PAGE DOWN key to see the rest of the agreement You must accept the agreement to continue Software Development Kit the setup MICROSOFT SOFTWARE LICENSE TERMS E MICROSOFT DIRECT END USER RUNTIME 3 These license terms are an agreement between Microsoft Corporation or based on where you live ane of its affillates and you Please read them They apply to the software named above which includes the media on which pou recenved it if any The terms also apply to any Microsoft updates O accept the agreement E don t accept the agreement Back Next gt Once read click on I agree with the terms and conditions 12 DeeGreen User Guide Installing Microsoft R Directa Ry Directs Setup Install Directs runtime components Directx Runtime Install This install package will search for updated Directs Runtime Components and update as necessary It may take a few minutes To start installation please click Next Click on Next to run the installation Installing MicrasottiRy DirectkiRy Progress Please walt while Setup completes the following actions H Install
15. ua 1 A N A N A ast L T P iae A Service buttons l I I A a We Nx M X M N ien 9o kA 7 J ae Be ee eee gee geen ase nae i e a A CA e X Y x sed X a A a A ett gee LA T A e 4 c k Ye x Operation screen gt DeeControl File PRINTING MODEL STEP 1 FILAMENT PLA Fasettings QUALITY OF PRINT good quality print with supports CONTINUE Printing screen 15 DeeGreen User Guide b DeeControl description DeeControl is a software that allows the model preparation gt gt I i gt c DeeControl on MS Windows platforms require DirectX 10 0 or later Input data for DeeControl have to be in STL format Output DeeControl data are in GCO format The printer can print from GCO files saved on SD card in the root directory only DeeControl detects printer connected to the computer automatically The printer can be disconnected from the computer during the printing process without it being interrupted From launch to printing On the welcome screen A AA aim A ilie Once DeeControl is launched welcome screen will be displayed Check that your printer is turned on and connected to your computer You can select the model to be printed either from the most recent list or using the proper buttons On the preparation screen A On the preparation screen you can o Add another model onto the platform using
16. ulation usage and installation in conflict with this User Guide Terms amp conditions A The manufacturer is responsible for proper device and related software functioning all in accordance with this User Guide A All malfunctions and flaws caused by manufacturing process or montage are covered by the manufacturer within the limits of the warranty A Arightful printer owner is eligible for free repair should there be a flaw within manufacture s responsibilities Flaws shall be fixed within 30 days from the day the flaw was reported The warranty does not cover malfunctions and or interruptions caused by A Usage of low quality filaments A Installation in contradiction with this User Guide valid laws and norms A Operation in inappropriate climate conditions A Inappropriate manipulation A user is obliged to pay work and departure of technician costs in case of inappropriate reclamation or demand to A Fix a flaw caused by a user A Fix illegally altered printer 17 DeeGreen User Guide A A A Check and clean the printer Repairs caused by power supply blackouts Repairs caused during printer start up installation and or use of low quality filaments The warranty is void when A z P dE Fe gt The printer construction is altered Moving parts and axis maintenance was not conducted in accordance with this User Guide within the 4 months period after the purchase The maintenance was not conducted after
Download Pdf Manuals
Related Search