Heavy Duty Jack Stands - Northern Tool + Equipment
Contents
1. 2 1 928254 SUPPORT PIN AND LANYARD 1 TWO YEAR LIMITED WARRANTY For a period of two 2 years from date of purchase SFA Companies will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship under normal usage This limited warranty is a consumer s exclusive remedy Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to SFA Companies Warranty Service Department 10939 N Pomona Ave Kansas City MO 64153 Except where such limitations and exclusions are specifically prohibited by applicable law 1 THE CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE 2 SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER 3 ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO TWO YEARS OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED 4 ANY MODIFICATION ALTERATION ABUSE UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation2. may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SFA Companies HEIN WERNER 10939 N Pomona Ave Kansas City MO 64153 816 891 6390 customerservices heinwerner automotive com AUTOMOTIVE
3. sure that all tools and personnel are clear before lowering load 1 With suitable jack raise vehicle clear of stands 2 Carefully release Support Pin and adjust Extension Tube to lowest position 3 Carefully remove stands then lower vehicle with lift device MAINTENANCE To help prevent rust wipe clean after each use Do not apply oil or lubricant to ANY portion of this product Always keep Support Pin with base section and replace Lanyard if necessary If rust appears sand affected area and cover with suitable utility paint Please note that there is no replacement part applicable to this device Storage Store stands in upright position and in a clean dry area REPLACEMENT PARTS For replacement partsd product labels and owners manual call or write Hein Werner Customer Support 10939 N Pomona Ave Kansas City MO 64153 U S A Tel 816 891 6390 Fax 816 891 6599 E Mail customerservices heinwerner automotive com Some components of these jack stands are not available for replacement Jack stands must be replaced as a matched set and must never be used singly or with another make or model stand HW93511 REPLACEMENT PARTS ITEM PART NO DESCRIPTION QTY J 1 928254 SUPPORT PIN AND LANYARD 1 f 2 928253 CASTER 2 3 928256 HARDWARE KIT 1 Q J Includes hardware for both casters and securing fasteners Q N HW93512 REPLACEMENT PARTS ITEM PART NO DESCRIPTION QTY
4. HEIN WERNER AUTOMOTIVE Made in the U S A Heavy Duty Jack Stands Operating Instructions amp Parts Manual CCCCCCLLeE IF ait eee J oy Model Number Capacity per pair wey HW93512 10 Ton Model Number Capacity per pair HW93511 10 Ton A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death e Leer comprender y seguir las instrucci nes antes de utilizar el aparato e Read understand and follow all instructions provided with and on this device before using e El manual de instrucci nes y la informaci n de seguridad deben estar comunicado en lengua del operador antes del uso e No seguir estas indicaci dnes puede causar da os personales o materiales e Failure to heed these warnings may result in personal injury and or property damage SFA Companies 10939 N Pomona Ave Kansas City MO 64153 customerservices heinwerner automotive com Read this manual and follow all the Safety Rules and Operating Instructions before using this product SAFETY AND GENERAL INFORMATION Save these instructions For your safety read understand and follow the information provided with and on this pair of jack stands before using The owner and operator of this equipment shall have an understanding of the jack stands and safe opera
5. e Do not use if there are bent broken or cracked components noted including labels Ensure that all parts move freely 3 Read the this operator s manual completely and familiarize yourself thoroughly with the product and the hazards associated with its improper use before using this product 4 Always refer to the vehicle owner s or service manual for location of proper lift and support points OPERATION Use only on areas of the vehicle as specified by the vehicle manufacturer Use ONLY on vehicles whose support points are compatible with the saddle of the jack stand Incompatibility may result in structural damage to the vehicle and or jack stand Structural damage to either may result in sudden and unexpected loss of load height Only attachments and or adapters supplied by the manufacturer shall be used 1 Change Saddle height by adjusting the Extension Tube then insert the Support Pin through both Adjustment Holes in Extension Tube 2 Check that Support Pin is securely seated across cutouts in top of Collar before loading Ensure that Support Pin is inserted completely so that bar stop engages the collar 3 Carefully position jack stands so that load will be centered on stand s saddle Slowly lower the vehicle onto stands Check to ensure vehicle is secured before working on around or under Use wheel chocks on all unlifted wheels in both directions to prevent inadvertent movement as To lower load Be
6. ht Net Weight HW93512 HWO3S T 18x18 144 bs 10 Ton 16 x 16 19 1 2 31 1 2 44 Ibs Saddle S ae Height Adjustment Holes e AEn en Tube Ag Support Pin 5 16 18 x 3 4 Carrying Handle VIS Securing Fastener Ne Collar K aa Lanyard Base i Transport Casters Figure 1 Hein Werner Heavy Duty HW93511 only Jack Stand Components l HW93511 shown i Rated capacity is PER PAIR DO NOT exceed rated capacity Use as a matched pair to support one end of a vehicle only Use only ONE 1 PAIR per vehicle Use only on hard level surface Center load on saddle Jack stands are not to be used to simultaneously support both ends or one side of a vehicle No alterations shall be made to this device To avoid crushing and related injuries NEVER work on under or around a load supported only by a hydraulic Dm jack ALWAYS use adequately rated jack stands PREPARATION Assembly refer Fig 1 1 Make sure all parts are present If any part is missing or damaged do not attempt to assemble install or operate the product Contact Hein Werner Customer Service 816 891 6390 2 Insert Extension Tube into the Collar and attach securing fastener into hole in Collar to prevent inadvertent removal Before Use 1 Verify that the product and the application are compatible if in doubt call Hein Werner Customer Service 816 891 6390 2 Inspect stands before each us
7. ting procedures before attempting to use The owner and operator shall be aware that use of this product may require special skills and knowledge Instructions and safety information shall be conveyed in the operator s native language before use of these jack stands is authorized If any doubt exists as to the safe and proper use of these jack stands remove from service immediately Inspect before each use Do not use if broken bent cracked or damaged parts including labels are noted Any jack stand that appears damaged in any way operates abnormally or is missing parts shall be removed from service immediately If you suspect that the jack stand was subjected to a shock load a load dropped suddenly unexpectedly upon it immediately discontinue use until the stand has been checked by a factory authorized service center contact distributor or manufacturer for list of Authorized Service Centers It is recommended that an annual inspection be done by qualified personnel Labels and owner s manuals are available from manufacturer PRODUCT DESCRIPTION Hein Werner Heavy Duty Jack Stands are designed to support rated capacity partial vehicle loads consisting of one end of a vehicle Use as a matched pair to support one end of a vehicle only NEVER use automotive jack stands to support both ends or one side of a vehicle Use only one 1 pair per vehicle Rated capacity is per pair only SPECIFICATIONS Model Capacity Min Height Max Heig
Download Pdf Manuals
Related Search