Australia - New Zealand - Service
Contents
1. BLACKS DECKER EMax34i XE EMax34s XE 5 EMax38i XE EMax42i XE ea on Australia New Zealand 7 Original instructions Intended use Your Black amp Decker mower has been designed for mowing grass This tool is intended for consumer use only Features This appliance includes some or all of the following features 1 Switch box On off switch Upper handle Intelligent cable management Lower handle Cable storage holders Height adjustment Height of cut gauge 9 EdgeMax 10 Grass collection box 11 Clear grass flap 12 Carry handles Warning Read all of the Safety Maintenance Service manual carefully before operating this appliance Read all of this manual carefully before operating the appliance CON Assembly Warning Before assembly make sure that the appliance is switched off and unplugged Assembling the grass collection box fig A 0 The grass box requires assembly before use and comes in 5 pieces Clip the handle 13 into the lid 14 of the grass box fig A The handle will only fit one way round Clip the 2 sides 15 of the grass collection box together Make sure that all clips and guides are aligned fig B Align the assembled sides onto the bottom 16 of the grass collection box Ensure that the 4 guides 17 are aligned fig C Push the 2 parts together Apply even force around all e2. You may continue mowing until the grass collection box becomes full Emptying the grass collection box fig J EMax34i EMax38i amp EMax42i only Release the on off switch 2 Remove the grass collection box 10 Empty the contents from the front of the box Place the grass collection box on the ground and pull in and hold the grass compaction lever release button 30 Lift the grass compaction lever 29 into the vertical position and release the grass compaction lever release button 30 Empty the contents from the rear of the box Emptying the grass collection box EMax34s only When the grass collection box is full you should empty the grass in the collection box Release the on off switch 2 Remove the grass collection box 10 Empty the contents from the box 7 Original instructions Cable storage fig O The cable holders 6 provide a safe and convenient way to store the cable 31 when not in use Wrap the cable around the cable holders 6 in a figure of eight pattern Carrying the mower Warning Ensure the blade has completely stopped and disconnect the appliance from the mains The mower be carried using the convenient carry handles 12 Hints for optimum use f the grass is longer than approximately 10 cm make two cuts to obtain a better finish First mow at maximum height of cut then use a low or medium height of cut e In order to achieve optimum res
3. dges of the grass collection box securing the clips into position uniformly Check that each clip is fastened together securely Align the lid 14 onto the assembled grass collection box Ensure that the 10 guides 18 are aligned fig D Note Take extra care when aligning the 2 clips at the rear of the grass collection box Push down on the lid to secure all clips Begin at the back and ensure that all clips are securely located Fitting the lower handle fig E Insert the ends of the lower handle 5 into the corre sponding holes in the mower Press the handle down as far as it will go Secure the handle using the screws 19 Assembling the upper handle fig F Fit the upper handle part 3 to the lower handle 5 using the knobs 20 washers 21 and screws 22 as shown Note The upper handle can be fixed in 2 different height positions Securing the motor cable fig G The motor cable has to be fixed using the cable restraints Clip the cable to the upper and lower handle using the restraint clips 23 as shown Fitting the grass collection box fig N Lift the clear grass flap 11 and place the grass collection box 10 over the lugs 24 Replacing the blade fig L Warning Ensure the blade has completely stopped and disconnect the appliance from the mains Warning Only use the specified replacement blade Warning Use heavy duty gloves to grip the blade To remove the blade Turn the appliance ont
4. ff switch 2 Warning Never attempt to lock a switch in the on position Mowing fig P1 amp P2 EMax38i amp EMax42i only We recommend to use your mower as outlined in this section in order to achieve optimum results and to reduce the risk of cutting the mains cable Loop the mains cable through the intelligent cable management system 4 as shown fig H ensue that you leave approximately 100 cm of cable between the switch box 1 and the intelligent cable management restraint 4 e Ensure that the cable restraint can slide freely from one handle to the other Place the bulk of the mains cable on the lawn close to the starting point position 1 in fig 1 Switch the appliance on as described above Proceed as shown in fig 1 Move from position 1 to position 2 Turn right stepping over the cable and proceed towards position 3 The cable restraint will slide from one side of the handle to the other ensuring that the cable is laid out away from the cutting blade Turn left stepping over the cable and move towards posi tion 4 The cable restraint will slide from one side of the handle to the other ensuring that the cable is laid out away from the cutting blade Repeat the above procedure as required Warning Do not work towards the cable as shown in fig P2 Mowing fig P1 amp P2 EMax34s amp EMax34i only We recommend to use your mower as outlined in this section in order to achieve
5. o its side Using heavy duty gloves grip the blade Use a 13mm spanner to loosen and remove the blade bolt 25 by turning the spanner anti clockwise ac Remove the blade 26 and blade bolt 25 To replace the blade Offer the blade up to bolt shaft and locate the blade bolt 25 into the bolt shaft Note When fitting a blade the text on the blade must be facing the user Tighten the blade bolt 25 as firmly as possible by hand Using heavy duty gloves grip the blade e Use a 13mm spanner to securely tighten the blade bolt 25 by turning the spanner clockwise Use Warning Let the appliance work at its own pace Do not overload Adjusting the height of cut fig M1 amp M2 The height of cut is adjusted by the central height adjust mechanism there are 6 positions to choose from To set the height of cut Pull the height adjustment lever 7 away from the body of the unit 2 Move the lever towards the rear of the appliance to lower the height of cut Move the lever towards the front of the appliance to raise the height of cut Push the height adjustment lever 7 into one of the 6 height locations Note The height of cut can be viewed on the height of cut gauge 8 on the side of the unit Switching on and off fig 1 Switching on e Push in and hold the lock off button 27 e Pull the on off switch 2 towards the handle Release the lock off button Switching off Release the on o
6. optimum results and to reduce the risk of cutting the mains cable Place the bulk of the mains cable on the lawn close to the starting point position 1 fig P1 Original instructions R T Switch the appliance on as described above Proceed as shown in fig 1 Move from position 1 to position 2 e Turn right and proceed towards position 3 Turn left and move towards position 4 Repeat the above procedure as required Warning Do not work towards the cable as shown in fig P2 EdgeMax fig K1 amp K2 EdgeMax allows you to cut grass right up to the edge of a wall or fence fig K1 EdgeMax allows you to accurately cut grass right up to the edge of your lawn fig K2 With the lawnmower parallel with the edge of your lawn e Push the lawnmower along the edge of the lawn Ensure that the EdgeMax 9 is slightly over the edge of your lawn fig K2 Note The roller underneath the appliance provides stability when mowing over the edge of your lawn Compact amp Go fig J EMax34i EMax38i amp EMax42i only When the grass collection box is full you can compact the grass in the collection box You can determine how full the grass collection box is by looking through the clear grass flap 11 Release the on off switch 2 Using your right foot press the grass compaction lever 29 all the way down until it locks into place Note The grass in the collection box is now compressed into the rear of the box
7. ults only mow dry grass Troubleshooting If your appliance seems not to operate properly follow the instructions below If this does not solve the problem please contact your local Black amp Decker repair agent Warning Before proceeding remove the plug from the socket Possible Cause Possible solution Fuse faulty blown Replace fuse Increase the height of Grass too long l cut and move machine to shorter grass to start Thermal cut out Allow motor to cool and activated increase height of cut Thermal cut out Allow motor to cool and activated increase height of cut Height of cut too low Increase height of cut Cutting blade blunt Replace the blade Underside of machine Check underneath the Machine fails to operate Machine functions intermittently Machine leaves ragged finish or motor labours clogged machine and clear out as necessary always wear heavy duty gloves Blade fitted upside Refit blade correctly down 90590486 Technical data EMax34s XE EMax34i XE Voltage Power Input EMax38i XE EMax42i XE No Load Speed Height adjustment Blade length Hand arm weighted vibration value according to EN 60335 3 2 m s uncertainty 1 5 m s Australia amp New Zealand Stanley Black amp Decker 82 Taryn Drive Epping VIC 3076 Australia Tel 1800 444 224 Aust or Tel 0800 339 258 NZ 08 12 lt
Download Pdf Manuals
Related Search