Konica Minolta Confidential 1/8
Contents
1. Function Version1 except C452 1 Set the number of documents in the Memory RX User Box to 200 or fewer Attention In 2nd Version Function Version2 the number of documents where the compulsory memory RX user box can be saved has been enhanced from 200 to 500 If you downgrade the version without setting the number of documents to 200 or fewer it is impossible to perform Memory RX 2 If E mail Address has been set to the Destination of IP Address FAX change the Destination to IP Address Attention In 2nd Version Function Version2 it is possible to set the Destination of IP Address Fax to E mail Address 3 Delete OCR Dictionary data for Searchable PDF in Service Mode 4 Change Software Switch Setting to the following in Service Mode Switch No 25 HEX Assignment 00 5 Turn OFF ON the main switch Attention Some setting values in Service Mode and Administrator Mode are reset to the factory default refer to 1 4 2 2 5 Firmware downgrading procedure from 1st MR2 version Function Version1 to 1st MR version Function Version1 except C452 1 Install the Firmware of 1st MR version ver 5x to the MFP 2 If 3rd ver movie data has been installed delete it in Service Mode 3 Install 2nd ver movie data to the MFP Regarding to Firmware downgrading procedure from 2nd Version Function Version2 to ist Initial Version and Firmware downgrading procedure from 2nd Version Function Ver2. Software SW No 25 00 Need to change FW and movie data Konica Minolta Confidential 6 8 Program Release Information CSES ID No DLBT1001576ENO0 bizhub C652 C552 C452 MFP firmware Ver GCT 90 Subject Total Counter email communication does not function and 6 fixed 2010 06 08 4 3 How to check version ROM version You can check the ROM version in service mode Firmware Version For the details see the Service Manual 4 4 How to install movie data Use USB memory to install For the details see the Service Manual 4 5 How to install Loadable Device Driver PAG ee Qe N o0 Extract the attached exe file and save AOPOFW tar file to root directory of USB memory Insert the USB memory to FW installation USB port of MFP Turn ON the main switch Version of Loadable Device Driver is displayed on the MFP panel Press START button When the driver installation is complete Checksum is displayed on the MFP panel Turn OFF ON the main switch Select Authentication Device2 and Card2 in Service Mode gt Billing Setting gt Management Function Choice Press OK button Turn ON OFF the main switch Select appropriate card type in Administrator Settings gt User Authentication Account Track gt Authentication Device Settings 4 6 Function Version of Printer Driver 1 3 when using the driver as 3rd Function Version3 Printer Driver Select Version3
3. Company names and product names in this document are the registered trademarks for respective companies Copyright C 2010 KONICA MINOLTA BUSINESS TECHNOLOGIES INC 2010 06 08 Konica Minolta Confidential 8 8
4. in Properties of Printer Driver gt Configure gt Function Version when using the driver as 2nd Function Version2 Printer Driver Select Version2 in Properties of Printer Driver gt Configure gt Function Version when using the driver as 1st Function Version1 Printer Driver Select Version1 in Properties of Printer Driver gt Configure gt Function Version except C452 If Auto of Acquire Settings is on Function Version of MFP is applied to the Printer Driver automatically 5 Program that recommends applying at the same time Please refer to the PRI for bizhub C652 C552 C452 Mass Production Program 3rd version Ver 88 for details DLBT1000126EN Konica Minolta Confidential 7 8 Program Release Information CSES ID No DLBT1001576EN00 bizhub C652 C552 C452 MFP firmware Ver GCT 90 Subject Total Counter email communication does not function and 6 fixed 6 OpenAPI supported function level The following is OpenAPI supported function level on this firmware OpenAPI OpenAPI Function Level 3 5B Detail Auth 1 0 1 1 2 0 2 1 2 5 3 5 Scan to Application 2 0 2 1 2 2 3 0 3 1 3 5 PullPrint 1 0 1 1 2 0 2 1 2 5 3 5 Other A 1 0 3 5 Job Management 1 0 3 5 Setup 1 0 1 1 1 2 1 3 2 0 2 1 2 5 3 5 Auth 1 0 1 1 1 5 3 5 Scan to Application 1 0 1 1 3 5 Web Browser PullPrint 1 0 1 1 1 5 3 5 ScrSvr 1 0 3 5 Launcher 1 0 3 5
5. 0 6100 G00 80 for Fiery MFP controller TCP Socket AOPOO0Y0 6300 G00 20 MFP controller OPEN API AOPOOY0 7000 G00 12 MFP controller operation panel AOPOOY0 8000 GCP 90 MFP controller PIC AOPOOY0 8200 G00 55 MFP controller CSRC control Body AOPOOY0 8300 G00 02 Scanner AOPOOY0 0023 G00 81 97B1 Printer AOPOOY0 0050 G00 12 OC4E FAX board controller 15LA 0040 G02 12 000 B695 Operation panel message data AOPOOY0 8100 GCT 90 00 94DA ADF AOHTOY0 0024 G00 03 12E3 Finisher FS 526 A11PO0Y0 00N1 G00 27 1FEE C652 C552 Finisher FS 527 AOHROY0 0071 G01 02 80A4 C452 Finisher JS 504 A0830Y0 0070 G01 00 FF84 C452 RU A11PO0Y0 00R1 G00 02 EEAC COPY PROTECT 4152 Movie Data AOP00Y0 A000 G00 04 Dictionary Data AOEDOY0 B000 G00 0000 Konica Minolta Confidential 1 8 Program Release Information CSES ID No DLBT1001576ENO0 bizhub C652 C552 C452 MFP firmware Ver GCT 90 Subject Total Counter email communication does not function and 6 fixed 2010 06 08 2 2 Fixed issues The following issues are solved in this firmware 1 When printing the specific PCL file from SAP an image of page header transparency image is not printed correctly You can disable the Transparency adjustment processing Image Parameter with the following software switch Switch No 58 HEX Assignment 00 Transparency adjustment processing is enabled Default HEX Assignment 80 Transparency adjustment processing is disabled Th
6. Program Release Information CSES ID No DLBT1001576EN00 bizhub C652 C552 C452 MFP firmware Ver GCT 90 Subject Total Counter email communication does not function and 6 fixed 2010 06 08 1 Release version and download file name The newly released program version and download file name is as follows Release version lt C652 C552 C452 MFP Controller firmware gt Model Program Name Current Ver New Ver Program File Name Checksum Note bizhub C652 C552 C452 MFP firmware GCP 90 GCT 90 AOPOOYO F000 GCT 90 exe 858e Download File Name AOPOOY0 F000 GCT 90 exe C652_Series_PRI_DLBT1001576EN doc 2 What changed 2 1 Release of bizhub C652 C552 C 452 Special Program Card Ver GCT 90 The individual files and the checksum are as follows Program Name File Name Checksum Note BOOT AOPOOYO 1E00 G00 02 9ACB MFP controller subset AOPOOYO0 1F00 G00 10 C112 MFP controller AOPOOY0 0100 GCT 90 9043 MFP controller system AOPOOYO 1000 GCT 90 MFP controller print controller AOPOOY0 3000 G00 69 MFP controller print controller font AOPOOY0 3F00 G00 21 MFP controller print controller Demo Page AOPOOY0 3E00 G00 01 MFP controller MIO AOPOOY0 5000 G00 15 MFP controller PSWC AOPOOY0 5100 G00 20 MFP controller MIB IF AOPOOY0 5200 G00 10 MFP controller IPP IF AOPOOY0 5300 G00 10 MFP controller Outside controller IF AOPOOY
7. Track Registration gt Edit gt Pause User Settings gt Custom Display Settings gt Copier Settings gt Default Tab Density Settings User Settings gt Copier Settings gt Half Fold Tri Fold Specification lt image gt 2nd Version 5x Laas 2nd Version Function Vesrion2 Software SW No 25 10 3rd Version 8x 9x C652 C552 C452 3rd Version Function Vesrion3 MFP FW Ver 8x 9x movie data for 3rd Version OCR Dictionary data for 2nd Version Software SW No 2 Need to change Software SW B C652 C552 C452 2ndMR Version Function Vesrion2 MFP FW Ver 5x MFP FW Ver 8x 9x Need to Need to Ta for 2nd change FW movie data for 3rd Version change and movie Software OCR Dictionary data for data OCR Dictionary data for SW 2nd Version 2nd Version Software SW No 25 10 Need to change Need to change C652 C552 1st Version MFP FW Ver 2x movie data for 1st Version Software SW No 25 None Need to change FW and movie data C652 C552 1st MR Version Function Version1 MFP FW Ver 5x movie data for 2nd Version Software SW No 2 Need to change FW and movie data C652 C552 1st MR2 Version Function Version1 MFP FW Ver 8x 9x movie data for 3rd Version
8. has equal functions with 1st Initial Version except C452 2nd Version This is about Function Vesion2 in firmware ver 5x There are 2nd enhancement functions 2nd MR Maintenance Release Version This is about Function Vesion2 in firmware ver 8x 9x There are 2nd enhancement functions Function Version2 has equal functions with 2nd Version 3rd Version This is about Function Vesion3 in firmware ver 8x 9x There are 3rd enhancement functions After the Firmware of 3rd Version is installed the Function Version 1 2 3 is switched with software SW About Software Switch Settings Switch No 25 HEX Assignment 20 gt Function Version3 HEX Assignment 10 gt Function Version2 HEX Assignment 00 gt Function Version1 except C452 4 2 1 Upgrade 4 2 1 1 Firmware upgrading procedure from 1st Initial Version 1st MR Version to 3rd Version Function Version3 except C452 1 Install the Firmware of 3rd Version to MFP For details please refer to the Service Manual 2 If 1st ver 2nd ver movie data has been already installed delete it in Service Mode 3 Install 3rd ver movie data to MFP 4 Change Software Switch Setting to the following in Service Mode Switch No 25 HEX Assignment 20 Turn OFF ON the main switch 6 Install OCR Dictionary data for Searchable PDF to MFP If you use the Searchable PDF the following options are needed LK 105 UK 203 a 4 2 1 2 Firmware upgradi
9. ils please refer to the Service Manual 2 If 1st ver 2nd ver movie data has been already installed delete it in Service Mode 3 Install 3rd ver movie data to MFP Important Notice 1 Even when using Function Version1 please make sure to install 3rd ver movie data to MFP 2 About Software Switch Settings Switch No 25 HEX Assignment 20 gt Function Version3 HEX Assignment 10 gt Function Version2 HEX Assignment 00 gt Function Versioni except C452 Regarding to Firmware upgrading procedure from 1st Initial Version to 2nd Version Function Version2 and Firmware upgrading procedure from 1st Initial Version to 1st MR version Function Version1 please refer to the PRI for bizhub C652 C552 C452 Mass Production Program 2nd version Ver 54 for details DLBT0902562EN 4 2 2 Downgrade 4 2 2 1 Firmware downgrading procedure from 3rd Version Function Version3 to 2nd MR version Function Version2 1 Change Software Switch Setting to the following in Service Mode Switch No 25 HEX Assignment 10 2 Turn OFF ON the main switch Attention You can not use some 3rd enhancement functions refer to 3 4 2 2 2 Firmware downgrading procedure from 3rd Version Function Version3 to 1st MR2 version Function Version1 except C452 1 Set the number of documents in the Memory RX User Box to 200 or fewer Attention In 2nd Version Function Version2 the number of documents where the compuls
10. is issue is improved Correct the wrong Germany wordings in Box Settings of the PSWC Incorrect Drucker Correct Druckeinstellung Total Counter email communication does not function When printing the file from SAP IBM Info Print the printing result is different from HP printer s Using Active Directory with External Server when you enter the wrong password to the MFP only once Account is locked out even if select 3 invalid logon attempts in Account Lockout threshold setting If an IC card is placed on CU 1 during MFP startup the name of user No 1 registered in the MFP disappears On the MFP with Management Devicez2 is installed Failed to authentication is always displayed if Ver GCP 90 is installed in MFP 3 Functional restrictions 3 1 Functional restrictions Please refer to the PRI for bizhub C652 C552 C452 Mass Production Program 2nd version Ver 54 for details DLBT0902562EN Additional memory installation is required when using the following Open API functions 1 Functions using web browser on MFP 2 Initial screen customization If the firmware is GC6 57 or former the following symptom occurs When upgrading to this firmware please perform the following procedure If turn ON the main switch for the first time only first time after upgrading this firmware The Arp of any IP address other than IP address that is set is sent occurs This symptom does not occur when turning ON the mai
11. n switch for second times or more Please follow the following procedure after upgrading the firmware 1 After upgrading the firmware remove a network cable from the MFP before turning ON the main switch 2 Turn ON the main switch and the sub power switch 3 After Ready to copy is displayed insert the network cable 4 Turn ON the main switch Konica Minolta Confidential 2 8 Program Release Information CSES ID No DLBT1001576ENO0 bizhub C652 C552 C452 MFP firmware Ver GCT 90 Subject Total Counter email communication does not function and 6 fixed 4 How to install 4 1 How to install program Use USB memory to install For the details see the Service Manual Conditions for USB memory which can be used for updating the firmware are as follows Without security function Capacity 1GB to 2GB are recommend Compatible with to USB2 0 Formatted in FAT32 format 4 2 How to upgrade downgrade firmware Definition of terms 1st Initial Version This is about Initial Version of C652 C552 from ver 20 to ver 26 except C452 1st MR Maintenance Release Version This is about Function Version1 in firmware ver 5x 2010 06 08 There are not enhancement functions Function Version1 has equal functions with 1st Initial Version except C452 1st MR2 Maintenance Release2 Version This is about Function Version1 in firmware ver 8x 9x There are not enhancement functions Function Versioni
12. ng procedure from 2nd Version to 3rd Version Function Version3 1 Install the Firmware of 3rd Version to MFP For details please refer to the Service Manual 2 If 2nd ver movie data has been already installed delete it in Service Mode 3 Install 3rd ver movie data to MFP 4 Change Software Switch Setting to the following in Service Mode Switch No 25 HEX Assignment 20 5 Turn OFF ON the main switch Konica Minolta Confidential 3 8 Program Release Information CSES ID No DLBT1001576ENO0 bizhub C652 C552 C452 MFP firmware Ver GCT 90 Subject Total Counter email communication does not function and 6 fixed 2010 06 08 4 2 1 3 Firmware upgrading procedure from 2nd Version to 2nd MR version Function Version2 1 Install the Firmware of 3rd Version to MFP For details please refer to the Service Manual 2 If 2nd ver movie data has been already installed delete it in Service Mode 3 Install 3rd ver movie data to MFP Important Notice 1 Even when using Function Version2 please make sure to install 3rd ver movie data to MFP 2 About Software Switch Settings Switch No 25 HEX Assignment 20 gt Function Version3 HEX Assignment 10 gt Function Version2 HEX Assignment 00 gt Function Version1 except C452 4 2 1 4 Firmware upgrading procedure from 1st Initial Version 1st MR Version to 1st MR2 version Function Version1 except C452 1 Install the Firmware of 3rd Version to MFP For deta
13. ory memory RX user box can be saved has been enhanced from 200 to 500 If you downgrade the version without setting the number of documents to 200 or fewer it is impossible to perform Memory RX 2 If E mail Address has been set to the Destination of IP Address FAX change the Destination to IP Address Attention In 2nd Version Function Version2 it is possible to set the Destination of IP Address Fax to E mail Address 3 Delete OCR Dictionary data for Searchable PDF in Service Mode 4 Change Software Switch Setting to the following in Service Mode Switch No 25 HEX Assignment 00 5 Turn OFF ON the main switch Attention Some setting values in Service Mode and Administrator Mode are reset to the factory default refer to 1 Attention You can not use some 3rd enhancement functions refer to 3 Konica Minolta Confidential 4 8 Program Release Information CSES ID No DLBT1001576EN00 bizhub C652 C552 C452 MFP firmware Ver GCT 90 Subject Total Counter email communication does not function and 6 fixed 2010 06 08 4 2 2 3 Firmware downgrading procedure from 2ndMR Version Function Version2 to 2nd Version Function Version2 1 Install the Firmware of 2nd Version ver 5x to the MFP 2 If 3rd ver movie data has been installed delete it in Service Mode 3 Install 2nd ver movie data to the MFP 4 2 2 4 Firmware downgrading procedure from 2ndMR Version Function Version2 to 1st MR2 version
14. sion2 to 1st MR version Function Version1 please refer to the PRI for bizhub C652 C552 C452 Mass Production Program 2nd version Ver 54 for details DLBT0902562EN 1 Settings that are reset to the factory default Settings set value Service Mode gt Finisher gt Punch option setting Punch he Nondisplay So eA ae rk At Se RRA AD RD ND need ear arn A ee Punch UN O anea Shortcut key1 Shortcut key2 fn ia id nee Utility Counter gt User Settings gt Custom Display Settings gt Copier Settings Quick Settings1 Quick Settings2 These functions Quick Settings3 are not available E EEE E E Quick Settings4 at Shortcut key1 ca al cache en ees nc Cl a So Copy Tray2 Utility Counter gt Administrator Settings gt System Settings gt Output Settings gt Print Tray2 gt Output Tray Settings Print Reports Tray1 a ES EE Fax e AY Utility Counter gt Administrator Settings gt System Connection gt Prefix Suffix Auto This function is __ gt Prefix Suffix Automatic Setting Settings of not available Utility Counter gt Administrator Settings gt User Authentication Account Track gt Public Weer Access Restrict __ gt General Settings gt User Authentication gt Job Setting gt ON MFP aeee ON CONdition 2 gt Utility Counter gt Administrator Settings gt System Settings gt Restrict User Access gt Changing the From Allow gt Restrict Access to Job Settings gt Changing
15. the From Address Address 2 This setting is reset to Restrict only when Synchronize User Authentication amp Account Track is set to Do Not synchronize Konica Minolta Confidential 5 8 Program Release Information CSES ID No DLBT1001576ENO0 bizhub C652 C552 C452 MFP firmware Ver GCT 90 Subject Total Counter email communication does not function and 6 fixed 2010 06 08 3 If downgrading from 3rd Version Function Version3 to 1st Version Function Version1 and 2nd Version Function Version2 you can not use the following functions Administrator Settings gt Printer Settings gt Assign Account to Acquire Device Info Administrator Settings gt Security Settings gt Security Details gt Manual Input gt Allow All Individual Allowance Fax SIP Fax Restrict This setting is reset to Restrict if you select Individual Allowance Administrator Settings gt User Authentication Account Track gt User Authentication Settings gt User Registration gt Edit gt Function Permission gt Manual Destination gt Allow gt Allow All Individual Allowance Fax SIP Fax This setting is reset to Restrict if you select Individual Allowance Administrator Settings gt User Authentication Account Track gt User Authentication Settings gt User Registration gt Edit gt Pause Administrator Settings gt User Authentication Account Track gt Account Track Settings gt Account
Download Pdf Manuals
Related Search