YOSHIMURA PIM II (EMS Peripheral Interface Module)
Contents
1. 66 Fax 909 591 2198 www yoshimura rd com 600XX399000 Page 2 of 5 6 Locate the stock Crank Position Sensor CPS behind passenger seat Disconnect stock CPS plug and connect the PIM 2 harness in line with fhe stock harness plug F TN m Mie ee Stock E er gt t gt Stock Harness 7 Locate the stock Power plug next to oil reservoir The power plug can be accessed from the oil reservoir cover Disconnect the stock Power plug and connect the PIM 2 harness In line with the stock harness plugs A f Stoel A S MATES 8 Locate the coil mount bolt behind driver seat Remove and install PIM Ground harness to coll mount bolt 5420 Daniels Street Chino CA 91710 Tel 800 634 9166 Fax 909 591 2198 www yoshimura rd com 600XX399000 Page 3 of 5 9 Locate the 2 stock Fuel Injector plugs White plug and Black plug Disconnect the stock Fuel Injector plugs and connect the PIM 2 harness In line with the stock harness plugs Stock Harness ed 10 Locate the Throttle Position Sensor TPS behind the airbox Remove stock airbox as per Factory Service Manual to access the TPS Using the provided T Tap plug install T Tap onto green TPS wire Connect PIM 2 harness to new T Tap plug v PIM 2 Harness j j 4 Ee CLA A t eg t e E y DAR is ET y gt vs S y gt A Py IN ne s k y f gt 4 pa 4 lt gt 4 s a e i A A h ae d d At AN ter si gt gt Ni g2. SOSIMURA RESEARCH AND DEVELOPMENT OF AMERICA INC YOSHIMURA PIM II EMS Peripheral Interface Module APPLICATION YEAR MODEL 2011 Polaris RZR XP 900 PRODUCT 600XX399000 PIM2 Fuel Injection Controller Kit y This product is designed for use in closed course racing and is not I intended for highway use y Read through all instructions before beginning Installation Areas of vehicle may be extremely hot Let vehicle cool down before beginning installation Always wear hand and eye protection and take precautionary measures to avoid injury or damage NOTE In the state of California it is illegal to modify the emission control system which includes the fuel injection of any vehicle for on or off highway vehicles 5420 Daniels Street Chino CA 91710 Tel 800 634 9166 Fax 909 591 2198 www yoshimura rd com 600XX399000 Page 1 of 5 TOOLS REQUIRED Metric Socket Set Screwdriver Power Drill Drill Bit Set INSTALLATION 1 Remove driver and passenger seat as per Factory Service or Owner s Manual 2 Disconnect the battery 3 Install PIM 2 bracket in compartment under driver side seat using supplied hardware Apply provided hook and loop adhesive to PIM 2 unit and insert into bracket 4 Remove engine access panel behind driver and passenger seat 5 Connect PIM 2 harness to PIM 2 unit and route harness towards the rear of the vehicle 5420 Daniels Street Chino CA 91710 Tel 800 634 91
3. t Us A 5 as Sy y Q noun Las A lt gt f a Al gt E 5 d A t r T Pa MES Stock i i gt 11 Re install airbox as per Factory Service Manual 12 Re install engine access panel 13 Re connect battery and re install driver and passenger seat as per Factory Service or Owner s Manual 5420 Daniels Street Chino CA 91710 Tel 800 634 9166 Fax 909 591 2198 www yoshimura rd com 600XX399000 Page 4 of 5 ya Power fConnector To PIM 2 zip Tes o o a zro 5420 Daniels Street Chino CA 91710 Tel 800 634 9166 Fax 909 591 2198 www yoshimura rd com 600XX399000 Page 5 of 5
Download Pdf Manuals
Related Search