Wheelchair Lift Ricon Model F9A Mirage
Contents
1. FIGURE 2 7 PLATFORM MANUAL RAISING Refer to Figure 2 7 To raise the platform insert the pump handle extension onto the pump release valve Make sure the notches at the end of the handle are fully engaged by the release valve pin Twist the handle CLOCKWISE until lightly snug to make sure that the pump is in the raise mode Insert the handle extension into pump handle socket and move the handle extension in the appropriate directions the manual backup pump may be installed either vertically or horizontally to raise the platform N CAUTION DO NOT TURN PUMP RELEASE VALVE MORE THAN 1 4 TURN COUNTER CLOCKWISE THE VALVE IS TOTALLY REMOVABLE WHICH WILL DISABLE ALL AUTOMATIC AND MANUAL UP DOWN FUNCTIONS 227NFOASN1 A Refer to Figure 2 8 To lower the platform insert the handle extension onto the pump release valve and slowly twist the handle 1 4 turn COUNTER CLOCKWISE until the platform begins to lower Allow the platform to lower to the desired position FIGURE 2 8 PLATFORM MANUAL LOWERING e Rollstop Manual Control Knob The rollstop manual control knob is used to operate platform rollstop if the lift is being operated manually Refer to Figure 2 9 To open the rollstop allow lift to lower to ground position pull and hold the contr2. 44 161 301 6000 A RICON ONE YEAR LIMITED WARRANTY refer to following page 320 9 501 1 1 RICON ONE YEAR LIMITED WARRANTY Ricon Corporation Ricon warrants to original purchaser of this product that Ricon will repair or replace at its option any part that fails due to defective material or workmanship as follows e Repair or replace parts for a period of one year from date of purchase Labor costs for specified parts replace under this warranty for a period of one year from date of purchase A Ricon rate schedule determines the parts covered and labor allowed If You Need to Return a Product Return this product to Ricon Please give as much advance notice as possible and allow a reasonable amount of time for repairs This Warranty does not Cover Malfunction or damage to product parts caused by accident misuse lack of proper mainte nance neglect improper adjustment modification alteration the mechanical condition of ve hicle road hazards overloading failure to follow operating instructions or acts of Nature i e weather lightning flood etc Note Ricon recommends that this product be inspected by an authorized Ricon service techni cian at least once every six months or sooner if necessary Any required maintenance should be performed at that time WARNING THIS PRODUCT HAS BEEN DESIGNED AND MANUFACTURED TO EXACT SPECIFICATIONS MODIFICATION OF THIS P
3. POSITION GROUND LEVEL FIGURE 2 2 PLATFORM POSITIONS 227NFOASN1 A D CONTROLS AND INDICATORS WARNING THE LIFT IS ALLOWED TO OPERATE ONLY WHEN THE VEHICLE MANUFACTURER S INTERLOCK CIRCUITRY IS ACTIVATED NEVER ATTEMPT TO OPERATE THE LIFT WITH THE INTERLOCK BYPASSED REFER TO THE VEHICLE OWNER OPERATOR MANUAL FOR INTERLOCK INSTRUCTIONS BEFORE OPERATING THE LIFT CONTROL PENDANT Refer to Figure 2 3 The control pendant is a hand held hardwired remote device that controls the lift functions The pendant contains two spring loaded double acting switches and one spring loaded push button switch To operate the gt OUT T UP or J DOWN functions press and hold the appropriate switch until the function is completed To operate the IN function the lt IN and the IN LOCKOUT switches must be pressed FIGURE 2 3 CONTROL PENDANT and held at the same time The lift is equipped with a feature that removes electrical power to the lift when it is not in use The power indicator contained on the control pendant shows when this power is supplied and illuminates only when the lift is in operation NOTE THE POWER INDICATOR SHOULD PROPERLY ILLUMINATE ONLY WHEN THE LIFT IS IN OPERATION IF THE INDICATOR DOES NOT ILLUMINATE DURING OPERATION OF THE LIFT OR REMAINS ILLUMINATED WHEN THE LIFT IS NOT IN OPERATION CONTACT AN AUTHORIZED
4. CAUTION DO NOT TURN PUMP RELEASE VALVE MORE THAN 1 4 TURN COUNTER CLOCKWISE THE VALVE IS TOTALLY REMOVABLE WHICH WILL DISABLE ALL AUTOMATIC AND MANUAL UP DOWN FUNCTIONS e Refer to Figure 2 11 Insert the pump handle extension onto manual backup pump release valve Make sure the notches at the end of the handle are fully engaged by the release valve pin Slowly twist the hand 1 4 turn COUNTER CLOCKWISE until the lift platform begins to lower oO FIGURE 2 11 LIFT OPERATION PLATFORM MANUAL LOWERING e Allow the platform to reach ground level e Insert the pump handle extension onto manual backup pump release valve Twist the handle CLOCKWISE until lightly snug and remove e Using the rollstop manual control knob and one hand on the rollstop OPEN the rollstop attendant and lift passenger should follow the instructions to ENTER or EXIT the vehicle as described in the lift Operating Instructions section of this manual TO MANUALLY STOW THE PLATFORM e Raise or lower the platform to the deploy stow position the platform frame must be parallel to the side of the lift enclosure If the exact position cannot be obtained slightly low is preferred to slightly high 227NFOASN1 A e Using the rollstop manual control knob and one hand on the rollstop close the rollstop un
5. case of IN OUT motor short circuit the circuit breaker button will pop out If pressing and releasing the button does not reset restore power DO NOT press and hold Contact an authorized Ricon service technician for repair Main Circuit Breaker Refer to Figure 2 5 The main circuit breaker is located in the vehicle engine battery compartment and is designed to interrupt electrical power to the lift electrical system in case of a short circuit In case of a short circuit the circuit breaker reset tab will pop down If pressing the reset tab UP and releasing does not reset restore power DO NOT press and hold Contact an authorized Ricon service technician for repair FIGURE 2 5 MAIN CIRCUIT BREAKER 227NFOASN1 A ar MANUAL CONTROLS Manual controls of the lift consist of the manual backup pump and the rollstop manual control knob For the descriptions of the manual controls refer to the following sections e Manual Backup Pump The manual backup pump is used to operate the lift if there is no electrical power Refer to Figure 2 6 The manual backup pump is shown within the optional pump enclosure The controls for the pump consist of the pump handle extension installed by the vehicle manufacturer near the pump or stored within the optional pump enclosure cover for raising the lift platform and the pump release valve for lowering PUMP ANDLE XTENSION
6. front wheels can tip the wheelchair and possibly injure the wheelchair occupant Do not expect the rollstop to stop a quick moving wheelchair as it is not designed for that purpose Use extreme care board the platform slowly and then lock the wheelchair brakes Be certain wheelchair fits safely on the platform and does not extend over the edges of the platform or interfere with operation of the rollstop When exiting vehicle NEVER back onto the platform Always face outward and make sure that the platform is at a safe vehicle floor level position and the outer rollstop is in an up and locked position 227NFOASN1 A Do not operate with a load in excess of 660 Ibs 300 kg Do not place arms legs or clothing in or near moving parts The lift is designed for ONE wheelchair and its occupant Do not overload lift Keep others clear while operating Do not allow an untrained person to operate Careful supervision is necessary if used by or near children Do not allow anyone to stand on the bridgeplate Bending this bridgeplate can Cause dangerous interference with the platform as its raises or lowers Always LOCK WHEELCHAIR BRAKES power chair users should turn off power and set brake before lift is operated Use extreme care in wet conditions Wheelchair brakes are less effective if the platform and or wheelchair wheels are wet Never leave platform outside of vehicle Always return lift to stowed position after use Be sur
7. lo Power Unit cated in Section V of this manual THIS SAFETY CHECK MUST BE PERFORMED BY AN AUTHORIZED RICON SERVICE TECHNICIAN SEVEN YEAR SAFETY CHECK or 25 000 26 000 cycles of operation Control Pendant Replace UP DOWN IN OUT and IN LOCKOUT switches Hydraulic Perform Hydraulic Pump Motor Removal and Installation procedures Power Unit located in Chapter V of this manual TEN YEAR SAFETY CHECK or 36 000 38 000 cycles of operation RICON CORP recommends that lift be refit after ten years of service END OF TABLE aa 227NFOASN1 A LIFT DECALS PART OF SERIAL NUMBER DECAL FIGURE 3 1 DECAL LOCATIONS AND PART NUMBERS 227NFOASN1 A ar
8. CON SERVICE TECHNICIAN USING RICON REPLACEMENT PARTS MODIFYING OR FAILING TO PROPERLY MAINTAIN THIS PRODUCT WILL VOID THE WARRANTY AND MAY RESULT IN UNSAFE OPERATING CONDITIONS B DAILY INSPECTION TABLE 3 1 DAILY SAFETY CHECK SERVICE LIFT AT STOWED POSITION Se Check that control pendant is not damaged and cable connectors are tight Hydraulic CAUTION Power Unit DO NOT ADD FLUID UNTIL PLATFORM IS LOWERED TO GROUND LEVEL ADDING FLUID WHILE LIFT IS FOLDED WILL CAUSE TANK TO OVERFLOW WHEN PLATFORM IS LOWERED TO GROUND LEVEL 1 Check for visible hydraulic fluid leakage 2 Ensure backup pump manual release valve is lightly snug 1 Place vehicle NON INTERLOCK mode and attempt to operate lift LIFT AT DEPLOYED POSITION Listen for any abnormal noises as the lift operates i e grinding or binding Lift noises Operation Torque Limit Clutch overloads properly clicks at the end of travel Carriage stops are in place and stop lift squarely Main Lift Ensure carriage lifting frame platform pivot pins are free from damage and ing Pivots locked in position with fasteners 227NFOASN1 A TABLE 3 1 DAILY SAFETY CHECK SERVICE POINT DESCRIPTION Check that platform mounting brackets are properly fastened to both sides of Platform the platform Check that handrail mounting bolts are tight RAISE PLATFORM TO VEHICLE FLOOR LEVEL Lift Opera Listen for any ab
9. K WHEN ATTEMPTING TO LIFT HEAVY ECTS Use ONE PERSON ON EACH SIDE of the lift to prevent mechanical binding e With fingers up and palms forward push the platform forcefully to start the lift moving inward As the lift begins to move inward maintain a constant pushing motion until the lift comes to rest completely inside the lift enclosure e Check that the stow loc plunger is engaged in the top front of the platform guide block 227NFOASN1 A lil MAINTENANCE egular maintenance of the RICON Mirage F9A Series Transit Use Wheelchair and Standee Lift is required to ensure its optimum performance and reduce the need for repairs This chapter contains a list of daily inspection check points a recommended maintenance schedule and a troubleshooting section that utilizes the control pendant power indicator A ADDITIONAL MAINTENANCE INFORMATION Additional maintenance information is available in the Mirage F9A Series Transit Use Service manual part number 320 94502 This manual is available from Ricon in printed hard copy or at the Ricon website in PDF format The website is located at www riconcorp com Click on RICON CORPORATION and then DEALER S ROOM at the website Entry to the dealer s room will require a Dealer Number and a Password WARNING THIS RICON PRODUCT IS HIGHLY SPECIALIZED MAINTENANCE AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED RI
10. OUND LEVEL ensure that the pump hydraulic fluid level is maintained at the required FULL level Add only Texaco 15 hydraulic fluid or equivalent U S mil spec H5606E or F fluid A CAUTION THIS SAFETY CHECK MUST BE PERFORMED BY AN AUTHORIZED RICON SERVICE TECHNICIAN ANNUAL SAFETY CHECK or 3600 4000 cycles of operation Perform Torque Limit Clutch Adjustment located in Section V of this Hydraulic Power Unit IN OUT Drive manual Cam Grease cam followers with an approved grease and wipe clean any ex Followers cess grease from cam followers and surrounding areas 227NFOASN1 A TABLE 3 2 MAINTENANCE SCHEDULE SERVICE Perform Drive Chain Adjustment procedure located in Section V of this manual Ensure that spur gears and final drive sprocket are securely pinned to main drive shaft Drive Chains Ensure that torque limit clutch and final drive sprocket are securely and Shafts pinned to idler shaft Following labeled directions on container spray lubricant Curtisol Red Grease No 88167 on final and primary drive chains and drive shafts Wipe clean any excess grease from drive chains and sur rounding areas Hydraulic Inspect hydraulic hoses for damage Cylinder Flow Control Valve Hoses and Check Hydraulic Cylinder and Flow Control Valve for evidence of Fittings leaks Ensure that all fittings are tightly secured Hydraulic Perform Hydraulic Power Unit Fluid Flush and Renewal procedure
11. Og RICON Innovation in Mobility Mirage F9A Series Transit Use Wheelchair and Standee Lift Operator Manual 04 19 02 32DF9ASO1 A 97 2002 RICON CORPORATION All Rights Reserved U S Patent Nos 5 228 538 5 253 973 5 373 915 5 556 250 Australian Patent No 661127 680501 Canadian Patent No 2 129 821 French Patent No 0 446 224 German Patent Nos 68925368 0 08 EP 0625896 B1 U K Patent Nos EP 0625896 B1 EP 0703766 GB 2 224 992 B Other U S and foreign patents pending Printed in the United States of America This RICON product must be installed and serviced by authorized RICON service technicians The operator must refer to this manual for operating instructions then retain it for future reference Customer Name Installing Dealer Date Installed Serial Number REVISION RECORD REV PAGES DESCRIPTION OF CHANGE ECO 320 9 50 Change dealer to service agent 002708 07 08 99 1 1 Delete Canadian product support listing 4058 320 9 501 All New release in two book format A 3 1 Added A Additional Maintenance Information section END OF LIST 32DF9AS01 A Chapter l A B Il A B TABLE OF CONTENTS Page INTRODUCTION 2 1 1 RICON 5 YEAR LIMITED WARRANTY 1 1 SHIPMENT INFORMATION sscsccscssssssssv
12. RICON SERVICE SERVICE TECHNICIAN FOR REPAIR UP DOWN SWITCH 227NFOASN1 A ELECTRICAL CIRCUIT BREAKERS The lift electrical circuit breakers are designed to interrupt electrical power to the lift in case of a short circuit The circuit breakers are located on the hydraulic power unit or optional pump enclosure and the vehicle engine battery compartment For descriptions of the lift electrical controls and indicators refer to Figure 2 4 shown within the optional pump enclosure and the following paragraphs M CIRCUIT BREAKER FIGURE 2 4 LIFT CIRCUIT BREAKERS WARNING REMINDER RICON SERVICE TECHNICIAN NEVER REPLACE ANY CIRCUIT BREAKER WITH A CIRCUIT BREAKER OF GREATER VALUE LOCATE AND REPAIR SHORT CIRCUIT TO CORRECT PROBLEM e Control System Circuit Breaker The Control System Circuit Breaker is found on the hydraulic pump assembly In case of a control system short circuit the circuit breaker button will pop out If pressing and releasing the button does not reset restore power DO NOT press and hold Contact an authorized Ricon service technician for repair e IN OUT Motor Circuit Breaker The IN OUT Motor Circuit Breaker is found on the hydraulic pump assembly In
13. RODUCT IN ANY RESPECT CAN BE DANGEROUS This Warranty is Void if The product has been installed or maintained by someone other than an authorized Ricon service technician The product has been modified or altered any respect from its original design without written authorization by Ricon Ricon disclaims liability for any personal injury or property damage that results from op eration of a Ricon product that has been modified from the original Ricon design No per son or company is authorized to change the design of this Ricon product without written authorization by Ricon Ricon s obligation under this warranty is exclusively limited to the repair or exchange of parts that fail within the applicable warranty period Ricon assumes no responsibility for expenses or damages including incidental or conse quential damages Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply Important The warranty registration card must be completed and returned to Ricon within 20 days after installation of this Ricon product for the warranty to be valid The warranty is not transferable The warranty gives specific legal rights and there may be other rights that vary from state to state 1 2 32 9 501 B SHIPMENT INFORMATION Because of the specialized nature of the product Ricon does not sell directly to the us
14. aintenance inspections are required at least every six months and a thorough inspection should be performed at the service intervals referenced in Table 3 2 Under conditions of excessive use more than 10 cycles per day service should be increased TABLE 3 2 MAINTENANCE SCHEDULE SERVICE TWO WEEK SAFETY CHECK 2 140 180 cycles of operation Ensure that all decals are affixed properly clearly visible and legible Replace if necessary Ensure that serial number is clearly marked and legible Ensure that rollstop pivot points and springs and bridgeplate pivot points actuator pivot points and cam followers are lubricated IN OUT Drive Ensure that there are no obstructions in the side channels THREE MONTH SAFETY CHECK 900 1000 cycles of operation Stow Level Perform Stow Level Alignment Check Procedures located in Section V of this manual Following labeled directions on container spray lubricant Curtisol Red Grease No 88167 on final and primary drive chains and drive shafts Wipe clean any excess grease from drive chains and surrounding areas Drive Chains and Shafts Main Lifting Following labeled directions on container spray lubricant Curtisol Red Am and Grease No 88167 on ball and socket joints at bridgeplate actuator rod Bridgeplate assemblies bridgeplate pivot points and rod endpoints Wipe clean any Pivot Points excess grease from parts and surrounding areas While platform is at the GR
15. andrail STOW PLATFORM Press and hold lt IN switch and the red IN LOCKOUT switch until the lift is fully stowed The lift will raise or lower to the proper stowing level and retract into the vehicle 227NFOASN1 A an MANUAL EMERGENCY OPERATION If the lift becomes inoperable under its electrical power it can be operated manually e MANUALLY DEPLOY THE PLATFORM e Allow enough space for lift operation and passenger boarding If a break down situation exists and the vehicle cannot be moved so that the lift system can be operated safely the operator must summon emergency assistance to move the vehicle before operating the lift e Fully open vehicle door s Ensure that there are no obstacles in the path of the lift left side of the lift raise and hold stow loc piston UP WARNING USE EXTREME CAUTION TO AVOID URY DO NOT ATTEMPT TO MANUALLY DEPLOY OR STOW THE LIFT USING LESS THAN TWO PEOPLE MANUALLY DEPLOYING AND OR STOWING OF THIS LIFT REQUIRES FORCES GREATER THAN 100 LBS ENSURE THAT THE PERSON OR OBJ ECT HOLDING THE STOW LOC PISTON IS NOT IN THE PATH OF THE LIFT PLATFORM OR FRAME DURING THIS OPERATION TO MANUALLY DEPLOY THE LIFT PLATFORM A LARGE FORCE IS REQUIRED TO OVERCOME THE TORQUE CLUTCH INITIAL RESISTANCE AFTER THE LIFT STARTS MOVING OUTWARD SUSTAIN A CONSTANT FORCE UNTIL THE LIFT REACHES THE DEPLOYED POSITION Using ONE PERSON ON EACH SIDE of
16. e that these safety precautions have been read and understood Review them periodically and ask any attendants or other operators to read them as well If there are any questions contact an authorized Ricon service technician or call Ricon Product Support DAILY SAFETY CHECK Inspect the lift before each use and check that the following conditions are met before operating All functions operate properly If unusual noises or movements exist DO NOT use and contact Ricon Product Support Vehicle interlock is operating properly No objects that may interfere with operation are present General appearance and lubrication are satisfactory and all fasteners are tight 227NFOASN1 A LIFT FUNCTIONS TABLE 2 1 LIFT FUNCTIONS atform extends deploys OUT of the vehicle from the IN stowed posi tion DOWN Platform is lowered from its present position either vehicle floor level or OUT deployed position The rollstop automatically lowers when the platform reaches ground level Platform is raised from its present position either ground level or OUT deployed position The rollstop automatically raises when the plat form leaves ground level Platform retracts stows from the OUT deployed position to the IN stowed position OUT DEPLOYED END OF TABLE NOTE HANDRAILS AND BRIDGEPLATE NOT SHOWN IN ALL VIEWS FOR CLARITY FLOOR LEVEL
17. ed Keep others clear during operation The product requires regular periodic maintenance A thorough inspection is recommended at least once every six months The product must always be maintained at the highest level of performance 320 9 501 1 3 D MAJOR LIFT COMPONENTS The references used throughout this manual are illustrated in Figure 1 1 and defined in Table 1 1 FIGURE 1 1 F9A SERIES TRANSIT WHEELCHAIR AND STANDEE LIFT TABLE 1 1 F9A SERIES TRANSIT LIFT TERMINOLOGY rer wane Reference points from outside the vehicle looking inward at the platform ree 4 Rear Lift Enclosure type structure rigidly attached to the vehicle that con tains the lift Pump Enclosure Optional enclosure that contains the lift electrical and hydraulic control components Electrical Circuit Circuit breakers that protect the lift in the event of an electrical Breakers and short circuit and electro hydraulic pump that performs the lift Hydraulic Pump raise UP and lower DOWN functions Pull Box Contains electrical connections terminals Control Pendant Hand held device used to control the lift operating functions 1 4 320 9 501 Not shown Part of traveling frame that contains the necessary Carriage components to extend deploy the platform OUT and retract stow the platform IN Not Shown The electrical gear mo
18. er Instead the product is distributed through the worldwide network of authorized Ricon dealers who perform the actual sale and installation When the product is received unpack the product and check for freight damage Claims for any damage should be made to the carrier immediately Be sure the installation kit contains all items listed on the kit packing list Please report any missing items immediately to Ricon Product Support The warranty and owner s registration cards must be completed and returned to Ricon within 20 days for the warranty to be valid NOTE The Sales Service personnel must review the Warranty and this Operator Manual with the user to be certain that they understand the safe operation of the product Instruct the user to follow the operating instructions without exception GENERAL SAFETY PRECAUTIONS The following general safety precautions must be followed during installation operation service and maintenance An injury no matter how slight should always be attended Always administer first aid or seek medical attention immediately To avoid injury always exercise caution when operating and be certain that hands feet legs and clothing are not in the path of product movement Read and thoroughly understand the operating instructions before attempting to operate Inspect the product before each use If an unsafe condition unusual noises movements exists do not use it until the problem is correct
19. evel EXIT PLATFORM Carefully exit platform RELEASE OCCUPANT RESTRAINT BELT LOWER HANDRAILS Raise LEFT slam lock handle and lower LEFT handrail to platform Raise RIGHT slam lock handle and lower RIGHT handrail STOW PLATFORM Press and hold IN switch and the red IN LOCKOUT switch until the lift is fully stowed The lift will raise or lower to the proper stowing level and retract into the vehicle TO EXIT VEHICLE ACTIVATE INTERLOCK Refer to the vehicle manufacturers operators manual to activate the vehicle interlock 0 set parking brake place transmission in park etc DEPLOY PLATFORM Press and hold the OUT switch until the lift is fully deployed RAISE HANDRAILS Raise RIGHT handrail until slam lock engages then raise LEFT handrail until slam lock engages MAKE SURE OCCUPANT RESTRAINT BELT IS FASTENED RAISE PLATFORM Press and hold the T UP switch until platform stops at vehicle floor level BOARD PLATFORM Position wheelchair facing outward if possible in center of platform and LOCK WHEELCHAIR BRAKES e should stand in center of platform and firmly grasp handrails LOWER PLATFORM Press and hold the DOWN switch until the platform reaches ground level and the rollstop opens completely RELEASE OCCUPANT RESTRAINT BELT EXIT PLATFORM Carefully exit platform LOWER HANDRAILS Raise LEFT slam lock handle and lower LEFT handrail to platform Raise RIGHT slam lock handle and lower RIGHT h
20. he platform is at the de ployed OUT and ground level positions END OF TABLE 32DF9AS01 A 1 5 Il OPERATING INSTRUCTIONS his chapter contains safety precautions daily safety check lift functions control and indicator descriptions and operating instructions for the RICON Mirage F9A Series Transit Use Wheelchair and Standee Lift This chapter must be read and thoroughly understood by the operator before attempting to use the lift A SAFETY PRECAUTIONS The following safety precautions must be complied with at all times when operating the lift Refer to Figure 2 1 A dangerous situation exists when using the lift if the vehicle is parked on a slope Always operate the lift with the vehicle parked on level ground FIGURE 2 1 UNSAFE VEHICLE SLOPING Vehicle must be safely parked with the emergency brake ON before using the lift Inspect the lift prior to each use If any unsafe condition exists or unusual noises or movements are noticed DO NOT use and contact an authorized Ricon service technician for repair Read and comply with all warning labels and symbols affixed to the wheelchair lift When using the lift it is recommended that the occupant FACE OUTWARD The platform rollstop is designed to prevent slow inadvertent rolling off the platform The large rear wheels of a wheelchair can roll over the platform rollstop so we insist you always face outward Hitting the platform rollstop with the small
21. normal noises as the lift operates i e grinding or binding tion noises a Check that the lift platform stops at vehicle floor level Bridge Check that bridgeplate operates without obstruction s and rests squarely on plate vehicle floor LOWER PLATFORM TO GROUND LEVEL Lift Opera Listen for any abnormal noises as the lift operates i e grinding or binding tion noises Rolisto Ensure that rollstop opens and locks properly without obstruction s when it contacts the ground Hydraulic Power Unit While platform is at the ground level check that hydraulic fluid level is at the FULL level STOW LIFT Rolisto Ensure that rollstop closes and locks properly without obstruction s when the platform leaves ground level Lift Opera Listen for any abnormal noises as the lift operates i e grinding or binding tion noises Check that platform seeks proper stow level Torque Limit Torque Limit Clutch overloads properly clicks at the end of travel Clutch Sto Loc WARNING MANUALLY DEPLOYING AND OR STOWING OF THIS LIFT REQUIRES FORCES GREATER THAN 100 LBS DO NOT ATTEMPT TO MANUALLY DEPLOY OR STOW THE LIFT USING LESS THAN TWO PEOPLE Check that sto loc engages and lift will not deploy manually END OF TABLE an 227NFOASN1 A C MAINTENANCE SCHEDULE Maintenance inspections must be performed by an authorized Ricon service agent at least once every six months or sooner depending on usage M
22. nough space for lift operation and passenger boarding Take special care to ensure that the area is clear of obstacles and open vehicle door s completely before deploying the lift WARNING ATTENDANT SHOULD ALWAYS REMAIN NEAR PASSENGER TO RENDER IMMEDIATE ASSISTANCE IF NECESSARY KEEP OTHERS CLEAR OF LIFT WHEN OPERATING MAINTAIN PRESSURE ON SWITCH UNTIL FUNCTION IS COMPLETE BE CERTAIN WHEELCHAIR FITS PROPERLY ON PLATFORM AND DOES NOT CONTACT ROLLSTOP AND PREVENT IT FROM LOCKING AS THE PLATFORM RISES TO ENTER VEHICLE ACTIVATE INTERLOCK Refer to the vehicle manufacturer operators manual to activate the vehicle interlock 0 set parking brake place transmission in park etc DEPLOY PLATFORM Press and hold the OUT switch until the lift is fully deployed RAISE HANDRAILS Raise RIGHT handrail until slam lock engages then raise LEFT handrail until slam lock engages MAKE SURE OCCUPANT RESTRAINT BELT IS FASTENED 227NFOASN1 A LOWER PLATFORM Press and hold the 4 DOWN switch until the platform reaches ground level and the rollstop opens completely RELEASE OCCUPANT RESTRAINT BELT BOARD PLATFORM Position wheelchair facing outward if possible in center of platform and LOCK WHEELCHAIR BRAKES e STANDEES should stand in center of platform and firmly grasp handrails FASTEN OCCUPANT RESTRAINT BELT RAISE PLATFORM Press and hold the UP switch until platform stops at vehicle floor l
23. ol knob OUT and turn the knob COUNTER CLOCKWISE until the rollstop opens completely To close the rollstop pull and hold the control knob OUT turn the knob CLOCKWISE while raising the rollstop with the other hand until the rollstop closes and latches Z WARNING ROLLSTOP MUST BE IN UP POSITION BEFORE OPERATING LIFT FIGURE 2 9 ROLLSTOP MANUAL CONTROL KNOB 227NFOASN1 A a7 LIFT OPERATION Z WARNING 1 IMPROPER USE OF THE LIFT CAN RESULT IN PERSONAL URY USERS MUST READ AND FOLLOW OPERATING INSTRUCTIONS THIS SERVICE OWNER MANUAL ADDITIONAL COPIES OF THE SERVICE OWNER MANUAL ARE AVAILABLE FROM RICON CORPORATION 7900 NELSON ROAD PANORAMA CITY CA 91402 818 267 3000 OR 800 322 2884 2 DO NOT EXCEED RATED LOAD CAPACITY OF 660 POUNDS 300 KG 3 PRIOR TO USE INSPECT WHEELCHAIR LIFT FOR PROPER FUNCTION REQUIRED MAINTENANCE OR DAMAGE IF A PROBLEM EXISTS DO NOT USE LIFT AND CONTACT AN AUTHORIZED RICON SERVICE TECHNICIAN FOR REPAIR 4 THIS LIFT IS DESIGNED FOR USE BY WHEELCHAIR AND STANDEE OCCUPANTS ONLY RICON CORPORATION DISCLAIMS LIABILITY FOR DAMAGE OR PERSONAL INJURY RESULTING FROM MODIFICATION TO THE LIFT LACK OF MAINTENANCE OR REPAIR NEGLIGENCE ABUSE OR FAILURE TO FOLLOW LIFT OPERATING INSTRUCTIONS Before operating lift be certain vehicle is safely parked on level area away from traffic with the emergency brake ON Allow e
24. r the platform to the ground After the user departs the platform is raised and retracted IN stowed The F9A Series Lift is an underfloor electro hydraulic wheelchair lift with a powerful electric motor and electrical hydraulic pump and a powered rollstop The lift also contains a built in manual backup pump and rollstop manual control knob If the lift loses electrical power two or more people can extend the lift and raise and or lower the lift manually This manual contains operation and main tenance instructions and a troubleshooting guide for the lift It is important to user safety that the lift operator s be completely familiar with the Operating Instru ctions chapter of this manual Once the lift is installed itis very important that the lift be properly maintained by following the Ricon recommended cleaning lubrication and inspection instructions If there are questions about this manual or additional copies are needed please contact the Ricon Product Support Department at one of the following locations Ricon Corporation 7900 Nelson Road Panorama City CA 91402 818 267 3000 Outside 818 Area Code 800 322 2884 World Wide Website sscssssssssssssrcssssessrsesrsessesessnsrsecesasaes www riconcorp com Ricon U K Ltd Littlemoss Business Park Road Droylsden Manchester United Kingdom M43 7
25. sssssssssessssesesessesvsssssassssssssoneseee 1 3 GENERAL SAFETY PRECAUTIONS v sccssssssssssssssssssesecessssssssssasssssessoneseee 1 3 MAJ OR LIFT COMPONENTS 1 4 OPERATING INSTRUCTIONS sssrinin 2 1 SAFETY 2 2 1 DAILY SAFETY CHECK 2 2 LIFT FUNCTIONS 2 3 CONTROLS AND 2 4 KIRT OPERATION gin 2 8 MAINTENANCE a cas te ata 3 1 ADDITIONAL MAINTENANCE INFORMATION 3 1 5 2 222 ta 3 1 MAINTENANCE 5 3 3 EFT DECAL 3 5 320 9 501 iii INTRODUCTION he RICON Mirage F9A Series Transit Use Wheelchair and Standee Lift provides wheelchair access to mass transit vehicles The patented movement ensures smooth safe entry and exit and easily lifts up to 660 pounds 300 kilograms Itis designed to be operated by a trained attendant or vehicle driver After activating the vehicle manufacturer installed safety interlock and by using the lift control switches the lift extends OUT or deploys from the vehicle and rises to the vehicle floor height The user boards the large non skid platform and the operator uses the control switches to gently lowe
26. the lift to prevent mechanical binding grasp the handrails and pull firmly Best results are attained by starting the deployment with a sharp tug and sustaining a constant pull until the lift is all the way out against the carriage stops e MANUALLY RAISE THE PLATFORM e Refer to Figure 2 10 Insert the pump handle extension onto manual backup pump release valve Make sure the notches at the end of the handle are fully engaged by the release valve pin Twist the handle CLOCKWISE until lightly snug and remove FIGURE 2 10 LIFT OPERATION PLATFORM MANUAL RAISING 2 lt CAUTION DURING MANUAL RAISING OF THE LIFT DO NOT RAISE THE PLATFORM MORE THAN 1 1 2 ABOVE THE VEHICLE FLOOR LEVEL ANY EXCESSIVE TRAVEL WILL MAKE IT DIFFICULT TO ENTER THE PLATFORM AND OR DAMAGE THE LIFT BRIDGEPLATE ACTUATOR THE OUTER EDGE OF THE BRIDGE PLATE MUST REST SQUARELY ON THE VEHICLE FLOOR e Insert handle extension into manual backup pump handle socket Move pump handle in the appropriate directions to raise the platform to the vehicle floor level lift passenger and attendant must follow the instructions to ENTER or EXIT the vehicle as described in the lift Operating Instructions section of this manual TO MANUALLY LOWER THE PLATFORM
27. til it latches WARNING MANUALLY DEPLOYING AND OR STOWING OF THIS LIFT REQUIRES FORCES GREATER THAN 100 LBS DO NOT ATTEMPT TO MANUALLY DEPLOY OR STOW THE LIFT USING LESS THAN TWO PEOPLE Use ONE PERSON ON EACH SIDE of the lift to prevent mechanical binding e With fingers up and palms forward push the platform forcefully to start the lift moving inward As the lift begins to move inward maintain a constant pushing motion until the lift comes to rest completely inside the lift enclosure e Check that the stow loc plunger is engaged in the top front of the platform guide block MANUALLY STOW THE LIFT FROM GROUND LEVEL In the unlikely event there is a hydraulic system failure and the manual backup pump is inoperative the lift may be stowed as follows by two or more able bodied persons e Raise or lower the platform to the deploy stow position the platform frame must be parallel to the side of the lift enclosure If the exact position cannot be obtained slightly low is preferred to slightly high e Using the rollstop manual control knob and one hand on the rollstop close the rollstop until it latches Z WARNING MANUALLY DEPLOYING AND OR STOWING OF THIS LIFT REQUIRES FORCES GREATER THAN 100 LBS DO NOT ATTEMPT TO MANUALLY DEPLOY OR STOW THE LIFT USING LESS THAN TWO PEOPLE THE PLATFORM IS HEAVY AND SHOULD BE LIFTED WITH USING EXTREME CAUTION AND PROPER LIFTING TECHNIQUE ALWAYS LIFT WITH LEGS AND NOT THE BAC
28. tor and associated mechanical hardware used to extend deploy the platform OUT and retract stow the platform IN Deployment System Not Shown Located within the lifting frame these arms connect the platform to the carriage to maintain the platform horizontal posit Lifting Frame Part of the frame that connects the platform to the hydraulic cylin 9 der for raising UP and lowering DOWN Slam Lock Manually activated mechanism used to lock the retractable handrail Assembly in the upright position the occupant sits or stands during lift opera Parallel Arm s Rollstop Manual Provides manual control of the rollstop in the event of a loss of Control Knob electrical power Platform Roll Front barrier to prevent the wheelchair from slow inadvertent roll stop ing off the platform during lift operation Handrails Provide hand hold for the platform occupant hand hold for the Provide hand hold for the platform occupant occupant Electrically interlocked safety belt that when properly engaged Occupant Safety helps prevent unintentional acceleration of wheelchair from plat form The lift will not operate using the UP or DOWN switches unless the belt is properly engaged Sto Loc Electrical solenoid that safety locks the lift in the stowed IN posi tion Plate that bridges across the platform and the vehicle threshold Bridgeplate Also serves as a rear rollstop when t
Download Pdf Manuals
Related Search