Home

here

1. Flex tubing Front of vehicle Page 7 of 16 11 Remove the plastic rubber plug under the vehicle close to the front doors Note This will be the pass through for the wires that control the LED assembly 12 From below the vehicle feed one 1 rubber seal and the protective flex tubing provided in the kit over the wire extending from the front LED module Note Be sure the beveled side of the seal is facing AWAY from the LED module Lower the vehicle Rubber 13 Carefully pry open three 3 plastic wire harness clips from inside driver side door sill Carefully pull back carpet edge 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 13 INSTALLATION Front of vehicle 14 Carefully peel back metallic tape to expose the access hole on the inside edge of the door sill Metallic tape Next feed the wires through the end of a long cable tie Use the cable tie to route the wires through the hole in the bottom of the vehicle and up through the access hole inside the door sill Section AA Fig 16 16 From below the vehicle feed the flex tubing through both access holes Slide another rubber seal provided in the kit over the wires and the flex tubing from inside the vehicle Inside hole Note The flex tubing is meant to pass through the rubber seals along Bottom Rubber with the wiring hole seal Make sure the surface of the grommet is completely seated and f
2. da O 12 Convolutedtube SSS i y y 13 Butyloum SSS d a ast U ee BOM 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 18 MECHANI ZATION ACCESSORY SERVICE CONNECTOR DRIVER Orange ACCESSORY SERVICE CONNECTOR PASSENGER Room Lamp White Batt Saver Purple Ignition Green C O N T R O L L E R lt C VDEMnnYr omr lt DSMnnr omr Mechanization 999F4 AXO10II Rev 04 18 2012
3. in park open the door and Verify the lights remain off 7 Turn off the car and open the door again and verify the lights come on when the door is opened 8 Unlock the doors wait and then lock the doors The Security lighting should turn off quickly with the doom lamp 9 Verify the functionality of all electrical vehicle components where harnesses were accessed 10 Check and clear trouble codes DTC 11 Check power window auto up control If it is not functioning properly hold switch in up position for 5 seconds 12 If this vehicle will be returned to a dealer lot or showroom for an extended period of time be sure the extended storage switch is placed in the inventory position Refer to section 9 Vehicle Preparation 13 If vehicle is NOT going into storage reset the radio presets to the recorded settings Page 16 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 17 BILL OF MATERIALS Nissan Security Lighting Kit 999F4 AX010 Parts Contained in Bag Labelled Installation Kit Qty Part Number __ LED Assembly within polythene bag 4 Wire retaining rectangle 40mm x 20mm Adhesive one side e o 5 Posi tapconnector Red Grey Cid 99M TODO 6 Cabletie 4 Black tof i 7 Cable tie 11 Black Mae 8 Alcohol preparation wipe ooo a y 9 Grey foam rectangle 80mm x 30mm x 5mm Adhesive one side Ja 10 Mud guard drilling template oo e i ia Grommet
4. the mud guard Clean carefully around holes where the LED modules and the retaining and prep with alcohol wipe tape will be mounted with soap and water Dry the surfaces Next wipe with an alcohol prep pad s at the areas shown Wipe both mud guards Allow minimum of 1 minute to be sure alcohol is a completely dry Clean between li Starting at the NON wire end rear remove the adhesive liner from the first LED Module LED module Carefully place the lens of the LED into the hole being sure to align the module straight and parallel with the edge of the mudguard Note Be sure installation temperature is within a range of 70 100 2F Apply approx 10 Ibs of firm pressure for minimum of 20 seconds to properly adhere the module to the mud guard 10 Repeat step 9 with the remaining three 3 LED modules Be sure the wiring between the modules does not become twisted as you are installing them to the mud guard Once all the LED modules are in place secure the wiring in between with one 1 piece of retaining tape as shown f Note Once the tape is down it is very hard Retaining Tape LED to pull back up Module Repeat process for both mud guards Page 6 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 12 VEHICLE PREPARATION Front of i Rubber seal Viewed from below Rubber seal Front of vehicle gt LED Wire
5. 99F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 14 POSI TAP INSTRUCTION Grey Cap woos i Straight and evenly spaced all the way around ii Tight and minimize gap wire jacket should be crushed Fig 3 e Insert wire to here 4 f Tighten i Straight and evenly spaced all around ii Tight and no gap and test the signal Vehicle Harness 2g a Accessory harness Page 10 of 16 1 Tap vehicle wire a Remove grey cap slot side from tap body b Slide cap around vehicle wire c Tighten the tap TIGHT with finger pressure NOTE Do not re use the tap for subsequent re installation Figures are not to scale 2 Inspect the tap to ensure correct installation NOTE Avoid putting pressure on the vehicle wire and tap for the remainder of the installation 3 Inspect the tap to ensure correct installation a Remove red cap non pierce side from tap b Remove the protective stub from the wire c Insert wire through the non pierce side opening d Spread the individual strands into fan shape e Insert wire into the tap body and ensure that it is all the way in f Tighten the tap TIGHT with finger pressure Confirm the tapped accessory wire a Inspect the tap to ensure correct installation b Test the signal to ensure that it is working properly Secure the tap a Secure the tapped wire on the non pierce side to the body of the tap with electri
6. GENUINE PARTS 1 DESCRIPTION Security Light Kit 2 APPLI CATION Altima Sedan 2013 3 PART NUMBER 999F4 AX010 Universal Security Lighting Kit 4 KIT CONTENTS Description Control module LED Assembly Misc parts kit TOOLS REQUI RED e Trim stick e Ratchet and 6 extension 8mm and 10mm sockets e 3 8 3 16 and 1 2 drill bits drill drill stops 2 Philips screwdriver e Short 2 Philips screwdriver Protective cloth e Scissors tape measure and metric scale Protective gloves e Electrical tape masking tape Needle nose pliers PRE I NSTALLATI ON CAUTION NOTES e Dealer installation recommended Instructions may refer to Service Manual e Installation may require special tools e This part is to be installed within a surface temperature range of 70 100 F CAUTION e This accessory must only be installed as specified in these instructions e Ensure at all times that parts are securely fitted and will not compromise the safe function of vehicle systems Page 1 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security lighting Kit 7 INSTALLATION OVERVIEW Room lamp Ignition Batt Saver LED Assembly Connectors LED Assembly 8 CRITICAL STEPS The following steps are critical and must be performed EXACTLY as specified to ensure proper installation Location of the lights must be followed exactly as described in this instruction Posi Tap instructions m
7. am Foam taped tape Use a cable tie to secure the Connector Accessory Connector to the existing harness as shown Note The view shown here is looking up under the dash from behind next to the parking brake pedal Harness Parking Brake aie a Wrap the Control Module with foam tape Fuse wend to prevent rattle Use a cable tie to secure Foam wrapped control module aii XS it to the existing wire harness at the base of the fuse block 27 Route the wires along the existing harness in the footwell Bundle and secure any excess wire with cable ties as shown Page 13 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 15 INSTALLATION Passenger Side Typical 100mm to 120mm Cable ties Flex Tube Accessory connector plug Passenger Footwell Fig 30 Part 999Q9 AY000 Black wire Black Red wire Page 14 of 16 Route the wires from the passenger side up towards the dash by running the wires along the existing harness and securing with cable ties Note Recommended spacing for cable ties is 100mm to 120mm Position cable ties as shown Locate the passenger side Accessory Connector plug It will be behind the glovebox on the right side as shown in this cutaway view Using a posi tap connect the Black wire from the LED Assembly to the Black wire on the Accessory Connector Harness Using a posi tap connect the Red wire from
8. arness Green wire from the LED Assembly to the Orange wire on the Connector Harness HARNESS NOT INCLUDED IN KIT REFERENCE PART NUMBER 999Q9 AY000 Page 11 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 15 INSTALLATION Accessory Connector Wire Electrical tape wrap around oe twice Shrink wrap end of Wire bent down Wire from LED Assembly Foam tape Cable tie Fig 24 Foam taped eA St Parking brake Fuse panel Route above these cables Page 12 of 16 22 Follow this finishing procedure on all posi taps Leave a short length of wire extended past the posi tap and bend down as shown Use electrical tape to secure the extra wire against the posi tap with at least two revolutions Note Make sure that the end of the wire is completely covered by the tape 23 Wrap the posi taps with foam tape to prevent rattle Route the wires up under the dash along the existing harness Feed the wires above the hood release and parking brake release cables Use a cable tie to secure the wiring to the large harness loop ahead of the fuse panel Note The view shown here is looking up under the dash at the parking brake pedal 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 15 INSTALLATION Fig 25 25 Plug the Accessory Connector Harness into the vehicle connector plug on the driver side Wrap the Connector in fo
9. cal tape 2 2 revolutions b Secure the body to harness where vehicle wire is being tapped with electrical tape 2 2 revolutions 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 15 INSTALLATION CAUTION e Ifa vehicle wire is being used by another accessory and a posi Tap is present tap the accessory wire NOT the vehicle wire Accessory connector plug oa bm A Q rf iver footwell D pirt Part 999Q9 AY000 Fig21 Black wire Green wire Purple Shrink wrap 20 Locate the driver side Accessory Connector plug It will be located up under the dash above the vehicle diagnostic port as shown Pull the plug down for easier access Note Be sure to grab the connector and not the harness when separating the plug from the foam tape Note A previously installed accessory may be present If so carefully remove the accessory connector harness from the accessory connector plug before posi tapping It is recommended that all posi tapping be completed before reattaching the accessory connector harness to the plug Using posi taps connect the wiring as follows Black wire from the LED Assembly to the Black wire on the Connector Harness Orange wire from the LED Assembly to the Sky Blue wire on the Connector Harness White wire from the LED Assembly to the Yellow wire on the Connector Harness Purple wire from the LED Assembly to the Pink wire on the Connector H
10. est drilled with the mud guards on the vehicle The following steps are performed from below looking up at the bottom of the mudguard 4 Starting at the REAR edge of the mud guard measure and mark 460mm 18 inches from the rear edge of the guard Measure and mark 13mm 1 2 inch from the inner edge of the mud guard Apply the drill guide tape by peeling the adhesive backing off the tape and aligning the first drill mark with the starting hole position as marked on the mud guard Carefully apply the tape along the length of the mud guard Be sure to keep the drill marks on the tape at 100mm from the inside edge of the mud guard 13 mm 1 2 inch 13 mm 1 2 inch 406 mm gt _ 406 mm gt 406 mm gt 16 inches 16 inches If drill guide tape is not available use a tape measure to mark three locations at 16 inches apart These three hole locations are 13mm from the inside edge of the mud guard You can also use the LED assembly to determine the location of each hole Repeat process for both mud guards Using a 1 2 inch drill bit drill all the marked hole locations A step drill bit can be used as well Be sure to stop at the 1 2 inch step in the tool Clean each hole so there is no flashing or shoulder from the drill Page 5 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 12 VEHICLE PREPARATION Fig 8 Clean the inside surface of
11. ock may vary vehicle to vehicle 3 Record customer radio presets NOTE USE CAUTION WHEN REMOVING RE INSTALLING TRIM COMPONENTS TO AVOID DAMAGE SCRATCHES BREAKING OF CLIPS AND OR INTERIOR TRIM PANELS MOVE ALL TRIM COMPONENTS TO A PROTECTED AREA A WARNING Move driver and passenger seats to full gt back position Disconnect negative battery terminal before proceeding ORDER OF INSTALLATION Remove panels and trim 4 Route Wiring 7 Final Check Items Prepare mud guards 5 Install controller Install LED Assemblies 6 Reinstall all panels Page 3 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 11 INTERIOR PREPARATION 1 Use a trim stick to carefully pry off the trim panel along the bottom door seal from the back of the seat up to the footwell Note Begin prying the panel off at the rear edge and work forward 2 Repeat process for passenger side 3 Raise Vehicle Note Use caution when placing lift pads Page 4 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 12 VEHICLE PREPARATION 18 inches Rear of mud guard viewed from below Driver Side Front of vehicle Front of vehicle Fig 5 Tape edge flush with First location mud guard edge marked Drill tape Viewed from below First location 13 mm marked 1 2 inch 460 mm 18 inches 16 inches Note The Altima is b
12. ree of butyl i Rubber seal Raise the vehicle in place Page 8 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 13 INSTALLATION Rubber seal Viewed from below Front of vehicle ubber seal ae Clean surface before installing seal Driver Side Cable ties Cable ties T ypical 100mm to 120mm Flex Tube Page 9 of 16 17 Press the lower rubber seal into position Apply a butyl sealant around the flex tubing where it passes through the rubber seal and at the other end around the wires Be sure to clean surfaces before applying butyl Locate the support leg from the mud guard to the vehicle close to the bottom seal Drill a 3 16 inch hole midway between the guard and the vehicle Use a 4 inch cable tie to secure the wires to the support leg Note Be sure to allow sufficient bend radius in the tubing Lower the vehicle 18 Allow approx 3 of flex tubing over the wires on the inside of the vehicle Press the inside rubber seal into position Wrap electrical tape around the open end of the flex tubing Note Make sure both seals top and bottom are properly installed Repeat procedure for passenger side of vehicle Route the wires from the driver side up towards the dash by running the wires along the existing harness and securing with cable ties Note Recommended spacing for cable ties is 100mm to 120mm Position cable ties as shown 9
13. the LED Assembly to the Sky Blue wire on the Accessory Connector Harness Plug the Accessory Connector Harness into the vehicle connector plug on the passenger side HARNESS NOT INCLUDED IN KIT REFERENCE PART NUMBER 999Q9 AYOOO 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 15 INSTALLATION 31 Route the wires along the existing harness Bundle and secure any excess wire between the kick plate and the Accessory Connector with cable ties as shown Note Do NOT secure the wiring to the drain tube in any way 32 Close the three 3 wire harness clips inside the door sills and reinstall the carpet edge both sides see Fig 13 Note Be sure to align the rectangular carpet holes with the harness clips 33 Reinstall the side trim panels on both sides of the vehicle along the bottom door seals from the seat to the footwell see Fig 1 Note Trim all cable ties Check all wiring Make sure all trim is in place Page 15 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit 16 CHECK OUT Inspect the vehicle for unfinished work 1 Close all doors 2 Using the keyless entry fob press the door unlock 3 Verify the security lighting turns on and off with the dome lamp in the car 4 Enter the car and press the door unlock and then start the car 5 Verify the security lamps turn off when the car starts 6 With the car running shifter
14. ust be specifically followed as described Be sure to apply masking tape as needed in order to protect any areas that may become scratched or damaged by tools Be sure to apply foam tape to any wiring components that can be damaged over time by sharp edges Test the functionality of the kit before final clean up and reinstallation of interior panels Page 2 of 16 999F4 AXO10II Rev 04 18 2012 INSTALLATION INSTRUCTIONS Security Lighting Kit VEHICLE PREPARATION Apply parking brake Confirm the vehicle is no longer in the default shipping state Extended Storage Switch Pulled Up and BCM in Transit Mode Failure to confirm the vehicle has been removed from this state will result in the loss of normal vehicle operation The confirmation requires two checks 2a Locate the Extended Storage Switch 2b Turn the ignition switch from OFF to ON position If in the cabin fuse block Once located turn indicators illuminate for approx 1 minute the check that it is in the Customer vehicle is in shipping mode To exit shipping mode position See below for reference return the ignition switch to OFF position Simultaneously push the wiper and turn signal stalks downward and hold for 2 seconds Inventory Customer nacii PUSH DOWN ph SIGNAL WIPER ey INCORRECT na Seconds NOTE Typical vehicle condition shown here Switch is easily identifiable by the permanent push pull fuse holder Actual position on the fuse bl

here

Contents

Download Pdf Manuals

Related Search

Related Contents