S Type COOLDOME Install Manual
Contents
1. Tables above allow for 10 or less voltage line drop A handy website for custom Voltage drop on D C current an online calculator is http nooutage com vdrop htm or another great calculator site is nttp www altronix com app_notes calc php COOLDOME Input Power Configuration ST CD 12VDC Warning COOLDOME Enclosure runs on 12 VDC only If high voltage is applied directly to COOLDOME enclosure you will damage housing void warranty and create electrocution hazard that can be harmful or fatal Do not start wiring until you have fully read and understand these installation instructions External Power Supply The output of the S 250 12 external power supply can be adjusted up and down 1096 Itis recommended to keep the voltage at the S Type adjusted to at least 11 5 vdc but no more than 13 5 vdc By running the enclosure higher than 13 5 vdc may cause premature fan failure It is best to check and tune the voltage at the COOLDOME with a voltage meter at the time of installation and use the adjustment screw located on the S 250 12 to the right side of the terminal screws to raise or lower the output voltage For all outdoor wiring always use an outdoor rated wiring or wiring in weather rated conduit out from power supply into the COOLDOME Follow all local and applicable wiring and safety standards Please keep D C wire runs short to reduce low voltage line drop Also the suggested wiring gauge table is provid2. Cable can be multi conductor in single round cable bundle such as Cat5 6e burial rated or Conductor cable SJOOW water rated Conduit If Conduit is used in Lieu of Cable Gland Port Seals provided Then Use Only Liquid Tight Conduit amp fittings properly sealed Internal Wire feeds must be fully sealed prior to placing Enclosure into Service See Conduit Guidelines section of this manual We cmm v Component Check List amp Standard Hardware S Type Models O 0 3 000 eS ST HB MVP Models e e e i ST HB Solar ka Or P ov m ST RF MVP models ST CD models Included in S Type Package 1 S Type Enclosure Housing 1 2 Mounting Arm for Wall Mounting 1 3 Cable Gland Seals pre installed 2 4 Camera Mount Plate 1 5 4 dia x 3 8 Hex bolt hardware pack for camera mt 1 6 8 Screws S S to fasten Camera Plate within ST 6 7 dia Foam Plugs for conduit wire feed sealing 1 8 Rubber Plug for 72 I D NPT Hole Plugs to seal unused port 1 9 Humidity Control Pack in COOLDOME option only 1 10 Power Supply S 250 indoor style in COOLDOME option only 1 Not Included in this Package Camera Installation Tools Wall Mounting Bolts amp Hardware Pole Mount Straps amp Strapping Hardware Cabling for Power or Data S Type Optional Equipment Heater Blower Package Heater Blower Solar compatible 12VDC under 7 watt Tornado P
3. wt SHOCK HAZARD Failure to fully seal enclosure wire and cabling entry ports may lead to shock hazard unsatisfactory product performance a possibility of damage to electronics in the Dotworkz enclosure product including camera damage and damage to integrated electronics due to air driven moisture traveling thru the conduit condensing and collecting in the enclosure creating a short circuit hazard Electrical Putty amp Putty Tapes Silicone Sealants Foam Sealants use very sparingly Dotworkz does not endorse nor has it evaluated any of these products Test products first and follow all manufacturers instructions Follow all applicable electrical and building codes and installation guidelines End user assumes liability for applicability of these products and their effectiveness and incurred liability in using these products VENT STOPPER PLUGS for Conduit Foam Conduit F PI for I D ndui dotworkzA Systems Prevents Humid Air exchange from venting thru electrical conduit into Dotworkz sealed enclosure Thus eliminating condensation issues within Dotworkz sealed enclosures QUICK INSTALLATION GUIDE 1 Pull wires to final installed length 4 Push plug into conduit mouth with finger tips till it flush with outside of fitting 2 Open Vent Stop Plug and install over wire 5 Repeat steps 1 4 for any other conduit feeds as needed BHn 3 Pinch Plug to compress over wire and 6 To assur
4. Voltage before Hooking up Power Supply 110 VAC or 220 VAC Front of Power Supply with terminal strip Rear of Power Supply with Input Voltage Selector di i bro N High Voltage A C Input Single Phase USA Wiring Color Code Low Voltage 12 VDC Output Terminals Color Symbol Description Color Symbol Description Black L Line Conductor AKA Live Hot Red V Positive VDC White N Neutral Conductor Black V Negative VDC Green G Ground Conductor Safety Ground T A Xe 2 24V DC Low Voltage Wire Gage Selector Chart Per Conductor Pair Per Cooler 12 Volts D C Voltage Drop For D2 amp ST COOLDOME Wire Guage in AWG below Ba PHP ps 31 multiplier vdc drop ft drop vdc distance ft Acceptable line drop for Wire Gauge and Distance Excessive line drop for Wire Gauge Above includes 10 amps max current draw on Static Cooled Enclosure with 2 amps for max camera pwr Fused circuitry will allow up to 15 amps 12 vdc 24 Volts D C Voltage Drop For D2 amp ST COOLDOME in AWG below feet Distance ft gt gt 0 420 0 660 AWG 8 1 050 10 1 670 12 0265 0530 0 705 1 060 1 325 2050 14 LUE multiplier vdc drop ft drop vdc distance ft Acceptable line drop for Wire Gauge and Distance Excessive line drop for Wire Gage and Dist Above includes 6 5 amps max current draw on Cooled D2 with 1 5 amps for max camera amp accessry draw Fused circuitry will allow up to 15 amps 24 vde
5. camera heater and blower circuitry cooling circuitry and other systems installed in unit All screws on hinged lower must be tightened to create seal on enclosure Failure to create this seal may result in water incursion into enclosure This may lead to electrical shock failure and damage to electrical systems installed within enclosure including but not limited to damage to camera heater and blower circuitry cooling circuitry and other systems installed in unit Do not over tighten any Screws Stand Offs or other fasteners on this unit Failure to heed this warning will cause damage or failure of the S TYPE enclosure Electrical Conduit Guidelines For optimal performance your Dotworkz Enclosure is designed to be Air amp Water Tight to eliminate any moisture dust and insect damage safety performance reliability and maintenance related issues Use of Electrical Conduit without sealing the entry ports inside wire feeds within Camera Enclosure will subject the inside of your enclosure to possibility of condensation driven moisture dust and insect contamination hazards Dotworkz has provided each enclosure with two Cable Gland Strain Relief seal ports that fully seal enclosure to an IP68 rating Waterproof and Airtight Seal To properly seal only one round cable is used in each e cable gland port Holes on enclosure are 7 8 diameter ready for standard I D NPT connector or PG13 fittings However we real
6. OT EXPOSE COMPONENTS TO WATER OR MOISTURE 2 Retain Instructions The safety and operating instructions should be retained for RERUM The lightning flash with an arrowhead 3 Heed Warnings All warnings on the unit and in the operating instructions symbol within an equilateral triangle should be adhered to is intended to alert the user to the 4 Follow Instructions All operating amp user instructions should be followed presence of non insulated dangerous 5 Electrical Connections Only a qualified electrician should make electrical voltage within the product s enclosure connections that may be of sufficient magnitude to 6 Attachments Do not use attachments not recommended by the product constitute a risk of electric shock to manufacturer as they may cause hazards persons T Cable Runs All cable runs must be within permissible distance The exclamation point within an 8 Mounting This unit must be properly and securely mounted to a supporting equilateral triangle is intended to structure capable of sustaining the weight of the unit accordingly alert the user to the presence of a Installation should be made by a qualified installer important operating and b Installation should be in compliance with local codes maintenance servicing instructions c Care should be exercised to select suitable hardware to install the unit in the literature accompanying the taking into account both the composition of the mounting surface and appli
7. RESSED OR IMPLIE D INCLUDING BUT NOT LIMITED TO ANY AND OR ALLIMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2 312 3 OF THE UNIFORM COMMERCIAL CODE AND OR IN ANY OTHER COMPARABLE STATE STATUTE DOTWORKZ SYSTEMS HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON V1DEOLARM PRODUCTS OR NON DOTWORKZ SYSTEMS RECOMMENDED PRODUCTS THAT THE PURCHASER CHOOSES TO CONNECT TO THE PRODUCT LIMITATION OF LIABILITY THE LIABILITY OF DOTWORKZ SYSTEMS IF ANY AND PURCHASER S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WH ATSOEVER REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT DP CONTRACT SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE IN NO EVENT SHALL DOTWORKZ SYSTEMS BE LIABLE TO PURCHASER FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER PRODUCT INSTALLATION PRECAUTIONS WARNINGS ADDITIONAL INFORMATION RETAIN THIS DOCUMENT IMPORTANT SAFEGUARDS 1 Read Instructions All the safety and operating instructions should be read before the unit is operated CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO N
8. VAC 176 264VAC Selected by Switch D LDOME 12VDC Frequency Range 47 63 HZ Current Draw by COOLDOME C Active Cooler OFF 0 4A Active Cooler Peak On 10 5A Input Current Full Load Typ 4A 115VAC 2A 230VAC ctive Cooler OFF OAA Acie Cooler Peak On 10 Active Cooler On Typ 9 0A Cam Draw Not Incl Recommended Min Circuit Breaker for 110VAC In 10 A type C MTBF 238 9Khrs i nie eee Int Electrical Working Temp 20 70C Ep Ext Power Supply Output 18A 12VDC up to 50C Derate 0 5A deg C over 50C E Reusable Desiccant Canister The reusable desiccant canister contains forty grams of silica gel This will prevent moisture buildup inside the COOLDOME Make sure to remove the canister from its foil envelope packaging before the COOLDOME is put to use There is a small window on the canister white circle Ensure that the crystals are blue Occasionally especially in humid environments the canister may need to be serviced If so the crystals in the window turns pink indicating the silica gel is saturated with moisture and can be reactivated by being placed in an oven at 300 F for three hours or until the crystals turn blue again The gel can be reactivated virtually an infinite number of times Generic Camera Installation Open enclosure by unscrewing 4 captive phillps screws and open hinge Remove camera mount plate by unscrewing four philips screw and loosening 2 front came
9. accept NPT fittings or PG13 equivalent Wire feed can be directly into hollow of Arm with room for wire management within Arm body Hole on side of mount arm and feeds on bottom of S Type housing are clearance holes that will accept NPT fittings or PG13 equivalent A plug is provided with Arm hardware if this feed hole is not used Some customers will choose to provide amp use liquid tight fittings amp conduit to make the connection arm feed and S Type enclosure Always create a drip loop between all external conduit or cable connections between fittings and S Type Housing All cable feeds must be sealed before S Type housing is put into service to provide dry electrically safe and effective product performance S Type Strong Arm Mount Wall Mounting Pattern ae 3 60 Iemm Jus 4 0 C101 6mm Holes o 16 Clearance x Cad Not to Scale Pole Mounting S Type with Strong Arm Pre Install EZ Lock Pole Mount BR MPM1 sold separately by following Instructions detailed in Installation Guide provided with pole mount bracket Pole Mount requires user supplied stainless steel strapping to secure Pole Mount Bracket to the pole strapping into final desired position Locate four 4 5 16 18 x 1 5 Hex bolts amp washers provided with EZ Lock and securely fasten base of S Type Strong Arm to Bracket Attach housing to arm as shown tighten screws evenly but firmly on both sides of housing Adjust housing to desi
10. ackage Ring of Fire Package for Extreme cold weather COOLDOME Package Outdoor Power Supply option for COOLDOME IP67 rated PS Humidity Control Package Insulation Kits EZ Lock Pole Mount Bracket Kit BR MPM1 F X Tools recommended for Enclosure amp camera mounting Hand Tools Drill amp Bits Pole Strapping Tools Hand Tools 1 amp 2 Phillips head screw driver 1 Flat Blade screw driver or smaller 7 16 Socket wrench or box open end wrench or adjustable wrench 9 16 Socket wrench or box open end wrench or adjustable wrench Wire stripping tool For Wall Mounting Drill and Bits for user supplied fasteners for wall mounting enclosure For Pole Mounting Strapping Banding Tools for user supplied Stainless Steel Pole Straps Mounting S Type Enclosure Attaching Enclosure to Dotworkz Strong Arm Provided on S Type equipment for Ring of Fire amp COOLDOME models P A Locate amp assemble four 20 x 5 8 hex bolts with lock washers provided in hardware pack of Strong Arm Turn over S Type housing to show threaded base inserts pre install four diameter bolts in Tilt head of Strong Arm Note orientation of tilt locking screws toward rear of S Type Firmly tighten all four bolts to secure tilt mount to S Type housing Wall Mounting Mounting to wall requires four user supplied fasteners Mark pilot holes for four 4 mount holes either by marking with base or
11. ailure of the end user to follow the directions outlined in the product instructions failure of the end user to follow the maintenance procedures written and recommended in the product instructions and service manual or recommended by the International Security Industry Organization Furthermore Dotworkz Systems shall have no liability where a schedule is specified for regular replacement maintenance or cleaning of certain parts based on usage that the end user has failed to abide to such schedule attempted repair by non qualified personnel operation of the Product outside of the published environmental and electrical parameters if such Product s original identification trademark serial number markings have been defaced altered or removed Dotworkz Systems excludes from warranty coverage products sold AS IS and or WITH ALL FAULTS and excludes used Products which have not been sold by Dotworkz Systems to the Purchaser All software and accompanying documentation furnished with or as part of the Product is furnished AS IS i e without any warranty of any kind except where expressly provided otherwise in any documentation or license agreement furnished with the Product 4 PROOF OF PURCHASE The purchaser s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES DOTWORKZ SYSTEMS HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES EXP
12. ance the weight of the unit Be sure to periodically examine the unit and the supporting structure to make sure that the integrity of the SERVICE installation is intact Failure to comply with the foregoing could If the unit ever needs repair service customer should contact Dotworkz Systems 1 result in the unit separating from the support structure and falling with 619 224 LIVE 5483 for return authorization amp shipping instructions resultant damages or injury to anyone or anything struck by the failing unit UNPACKING Unpack carefully Electronic components can be damaged if improperly handled or dropped If an item appears to have been damaged in shipment replace it properly in its carton and notify the shipper Be sure to save 1 The shipping carton and packaging material They are the safest material in which to make future shipments of the equipment 2 These Installation and Operating Instructions Y For technical questions or product returns call Dotworkz Customer Service 866 575 4689 7 30 AM to 4 30 PM PST The proper technician will contact you as soon as possible The External Nut on All electrical wire feed Glands must be tightened to create a weather tight seal prior to putting S TYPE in service Failure to create this seal may result in water incursion into enclosure This may lead to electrical shock product failure and damage to electrical systems installed within enclosure including but not limited to damage to
13. ation of this housing mount allowing strong backing material to secure Strong Arm mount Hole on side of mount arm and on bottom of S Type housing are clearance holes that will accept 77 NPT fittings or PG13 equivalent Firmly tighten wire feed nuts to create water tight seal around cabling Only a single round cable bundle should be inserted per seal port for an effective seal For Installations using Liquid Tight conduit please refer to Conduit Guidelines provided near front of this manual Note A internal wire feeds must be fully sealed at enclosure to provide satisfactory product performance and a safe amp moisture free installation Firmly tighten four 4 stainless steel Phillips screws on top of S type lid to secure amp seal enclosure to complete installation Do not over tighten COOLDOME Input Power Configuration ST CD 12VDC T E Provided P S Must be B Site Power Available Housed Indoors or in a Nema Electrical Enclosure LOW VOLTAGE RUN t Mh 1 d jill i My TITIO s e i 12 VDC Cable to M COOLDOME 110 220 VAC Power Source 250 watt Step Down P S Single Phase Only High Voltage to 12 VDC a J Turn Off Power or leave power disconnected during Installation of All Wiring Follow all local and relevant electrical codes amp standards Test all Wiring and confirm correct voltages before wiring up amp powering up ST COOLDOME Select Input
14. dotworkz amp INSTALLATION GUIDE Mounting amp Sealing of Housing amp Electrical Details S Type COOLDOME ENCLOSURE mI ST CD 12V DC VT ST CD 24V DC d o a Li COOLDOMFE Enclosures LIMITED WARRANTY DOTWORKZ INC PRODUCTS DOTWORKZ SYSTEMS INC Warrants this Product to be free from defects in material or workmanship as follows PRODUCT CATEGORY PARTS LABOR All Enclosures and Electronics One 1 Year One 1 Year Power Supplies One 1 Year One 1 Year Accessory Brackets One 1 Year One 1 Year During the warranty period to repair the product the purchaser will deliver it to Dotworkz Systems Inc San Diego CA or return the defective product freight prepaid The product to be repaired is to be returned in either its original carton or a similar package presenting an equal degree of protection with a Return Materials Authorization number displayed on the outer box or packing slip To obtain RMA you must contact our Technical Support Team at 866 575 4689 Dotworkz Systems will return the repaired Product freight paid Dotworkz Systems is not obligated to provide purchaser with a substitute unit during the warranty period or at any time After the applicable warranty period purchaser must pay all labor and or parts and shipping charges The limited warranty stated in these product instructions is subject to all of the following terms and conditions 1 NOTIFICATION OF CLAIMS WARRANTY SERVICE If purchas
15. e an airtight seal caulk around insert into conduit feed mouth wires and cables coating entire plug surface with sealant Proper Cable Management to Enclosure Avoid common Installation Mistakes Only Use Qualified Installation or Service Technician for Installing amp Servicing Dotworkz Enclosures Power Must be disconnected and kept off while installing or Servicing Enclosure Follow All Local and Applicable Electrical Codes and Standards for Installation of Electrical components All Cable Ports wire feeds or Conduit must be fully sealed to eliminate moisture within Enclosure All Dotworkz Enclosures are required to be fully sealed before placing into service to protect integrated products to eliminate any moisture driven shock hazard to perform optimally as designed DRIP LOOPS Always Create a Drip Loop for all Cables or Conduit Entering Dotworkz D2 Housing from level or Above D2 Conduit Power Data amp Antennae To avoid gravity driven moisture entry into Enclosure i 1 f j Water Falls From Drip Loop b ee Cable Gland Strain Relief Port Seals To properly seal Dotworkz Cable Gland Strain Relief Ports will only accept One single round cable per port NO Romex Flat Cable SJOOW Cat5 Cat6 Coaxial Use Round Cable Only with Dotworkz Standard Cable Gland Port provide Cable Gland Port Seal Seals are designed for ONE single round cable only per port
16. ed on previous page to further prevent low voltage line drop and to guide you in selecting the proper wire gauge for the dc run from the power supply to the ST CD It is always advisable to use a drip loop on all wiring going directly into the ST enclosure to reduce the risk of water entering and damaging internal components All fittings and seals must be firmly tightened and sealed before placing the ST CD in service Inside the ST CD we have provided a convenient Screw cage clamp style terminal blocks to wire the 12 vdc positive V and the 12 vdc Negative V terminal Please strip the insulation off the last 3 8 of the wires and fasten wiring securely to terminal using a small blade screwdriver to tighten the caging mechanism on the terminal blocks Please be especially attentive to wire using the Proper Polarity so as not to damage the internal components or damage your camera within LOW VOLTAGE RUN Voltage Drop Table shown on prior page Where we conservatively try to keep the voltage drop under 1 2 vdc over the low voltage direct current run These multipliers are approximate and voltage drop Vd is maximum at full 12 amp load at 12 vdc This voltage drop is under fully loaded condition when the cooling unit is engaged and camera and all accessories are on Voltage drop will be much less if the current is not at full load Z2 UN Power Supply Specifications m p k COOLDOME Specifications Input Voltage 90 132
17. er believes that the product is defective in material or workmanship then a written notice with an explanation of the claim shall be given promptly by purchaser to Dotworkz Systems but all claims for warranty service must be made within the warranty period If after investigation Dotworkz Systems determines that the reported problem was not covered by the warranty purchaser shall pay Dotworkz Systems for the cost of investigating the problem at its then prevailing per incident billable rate No repair or replacement of any product or part thereof shall extend the warranty period as to the entire product The specific warranty on the repaired part only shall be in effect for a period of ninety 90 days following the repair or replacement of that part or the remaining period of the product parts warranty whichever is greater 2 EXCLUSIVE REMEDY ACCEPTANCE Purchaser s exclusive remedy and Dotworkz Systems sole obligation is to supply or pay for all labor necessary to repair any product found to be defective within the warranty period and to supply at no extra charge new or rebuilt replacements for defective parts 3 EXCEPTIONS TO LIMITED WARRANTY Dotworkz Systems shall have no liability or obligation to purchaser with respect to any product requiring service during the warranty period which is subjected to any of the following abuse improper use negligence accidents lightning damage or other acts of God i e hurricanes earthquakes modification f
18. ize our customers are retrofitting these connectors with electrical conduit fittings We acknowledge this industry customization and installation practice and would like to guide customers to properly install these products Conduit Guidelines 1 If wires cabling or conduit are coming at enclosure wire entry level or above always create a drip loop 2 Please use only approved watertight electrical conduit and connectors IP66 or better with proper seals and fittings installed amp fully seal 3 Then after all wire and cables are installed into enclosure Seal wire entry ports inside of enclosure with any number of commercially available sealing putty s Silicone Sealant or similar products that are approved by applicable local and relevant electrical codes Dotworkz supplies two diameter foam conduit plugs that when installed will assist in sealing off airflow in conduit feed thru at cable entry inside of enclosure Putty or Sealant can be used in conjunction with these plugs to assure a full seal inside enclosure cable feed entry FORCES AT WORK IN ANY UNSEALED CONDUIT WIRE FEED ENCLOSURE SYSTEM WARM MOIST IN UNSEALED CONDUIT MOVES THRU CONDUIT EXPANDING HEATED AIR IS PUSHED INTO ENCLOSURE THEN COOLS amp FEEDS EXPAND amp CONTRACT WHEN CONDUIT HEATS amp COOLS CONDENSES HUMID AIR CONDENSES ON SURFACES INSIDE WITH OUTSIDE TEMPERATURES ENCLOSURE Humid Air p 6 lt gt 4 Condensing to Water
19. l Gently but firmly tighten four enclosure cover screws to fully seal enclosure dotworkz amp S Type Exploded Detail Parts List 1 S Type Housing Base 2 S Type Hinge 3 Camera Mount Plate 4 8 Fasteners Screws 6 5 Lens Seal Gasket 6 Lens 0125 Lexan T Lens Face Plate 8 Lens Fastener Screws 6 9 S Type Housing Cover 10 Main Seal Gasket 11 10 Captive Machine Screws 4 12 Cable Gland Seals 77 I D 2
20. ra plate screws One 20 x 3 8 camera mount screw is provided on camera plate organize camera parts to be installed Using 4 bolt provided mating camera to mount bracket Adjust camera to sit strait and slightly overhang front of mounting bracket Gently but securely tighten bolt with camera pointing strait on mount plate Re install camera plate into S Type placing camera lens close to enclosure lens For cameras that have adjustable focal lens allow enough room for lens clearance Re install amp Tighten all mounting plate screws S Type COOLDOME Internal Wiring S Type COOLDOME F Before camera amp S Type COOLDOME after power amp camera installation typical Power install Pull power and Data cables into housing thru Cable Gland strain relief seal ports near rear of S Type enclosure Strip back wires on Low Voltage 12VDC power cable brought into enclosure observing DC polarity With a Volt Meter Check voltage on wires pulled in from power supply before attaching wires to assure Low Voltage 12 VDC input wires and proper polarity Hook up 12VDC to red terminal and DC ground wire to black terminal Tighten firmly with small flat blade screwdriver Hook up user supplied data cable to camera Install power cable to camera See camera power page if your camera power cable is not compatible with the power cable shown above F Be sure to tighten cable gland seals to assure a weather tight sea
21. red position using both pan amp tilt adjustment fasteners and tighten all bolts evenly amp securely so housing is pointing into final position Wiring Notes Wire feed can be directly into hollow of Arm with room for wire management within Arm body Hole on side of mount arm and feeds on bottom of S Type housing are clearance holes that will accept 77 NPT fittings or PG13 equivalent A plug is provided with Arm hardware if this feed hole is not used Some customers will choose to provide amp use liquid tight fittings amp conduit to make the connection arm feed and S Type enclosure Always create a drip loop between all external conduit or cable connections between fittings and S Type Housing All cable feeds must be sealed before S Type housing is put into service to provide dry electrically safe and effective product performance Always consult and follow all local and applicable electrical codes to install and service housing Always shut off power before installation and follow all applicable safety practices and guidelines Only qualified electrical technicians should prepare amp service wiring Fully read amp understand all installation guidelines before attempting to install wiring amp housing Site wiring can be installed behind or installed to side of base of the S Type Strong Arm Main body of this Arm has room for flush electric box or cable feed thru wall to be mounted behind mounting base Prepare wiring before install
22. using template guide on back page of this manual Drill pilot holes and bolt arm to wall securely Four holes on S Type arm will accommodate up to 5 16 diameter bolts Always assure there is strong backing material amp the proper strong amp secure to anchoring into aggregate material of wall is made Re assemble Housing with Pan Tilt BIO lount Arm jj S ti screws evenly also adjus amp tighten tilt screws into desired final position Be sure all fasteners are evenly and securely tightened After completing wiring close access door to wire feed on mount complete internal wire amp cable installation and close and seal housing top amp wire feed seals Wiring Notes Always consult and follow all local and applicable electrical codes to install and service housing Always shut off power before installation and follow all applicable safety practices and guidelines Only qualified electrical technicians should prepare amp service wiring Fully read amp understand all installation guidelines before attempting to install wiring amp housing Site wiring can be installed behind or installed to side of base of the S Type Strong Arm Main body of this Arm has room for flush electric box or cable feed thru wall to be mounted behind mounting base Prepare wiring before installation of this housing mount allowing strong backing material to secure Strong Arm mount Hole on side of mount arm and on bottom of S Type housing are clearance holes that will
Download Pdf Manuals
Related Search