advance adapters inc. p/n: 712531 scout t19 4 speed transmission
Contents
1. special 716156 that has the 716148 pressed into it This will extend the tip far enough out to reach the new input shaft 11 CLUTCH ITEMS 10 CLUTCH ITEMS 11 Clutch Pressure Plate CF260000 or CF360049 10 Clutch Pressure Plate CF360030 11 Clutch Disc 381021 1 1 16 10 splines 10 Clutch Disc 281226 1 1 16 10 splines Clutch Release Bearing N1714 Ford or N1439 Clip Release Bearing N1439 Clip or N1714 Fork BOLT PLATE TO FACE OF TRANSMISSION USING 4 FLAT HD SOCKET CAP SCREWS ZZ TOP 2 HEX HD BOLTS MUST BE IN PLACE 4H BEFORE PLATE IS BOLTED TO TRANSMISSION NEW GASKET OR SILICONE TO PREVENT OIL LEAKAGE ADAPTER CASTING PART 711531 MODIFIED PLATE 712529 UP PILOT BUSHING rr ART IN OILSEAL OPEN SIDE AICTE OLE O TOWARDS TRANSMISSION MAKE SURE IT FITS OVER SHAFT GROUND SURFACE PROCEDING SNAP RING SS Tuan n Sao Yd lL SY liye LH T19 4 SPEED TRANSMISSION CASE Soak GA SAY ae ENGINE CRANK D D A NEW BRASS SYNCRONIZED RING REQ D AWARRRRRRRRLRRARLLL AWARRARRARRALALLLLLLT N lly SS 4 A gt N KL I _ EI LETT F ASS MSE f q ES Fa ANALY e C Ww z i SSS fe ane a MIN 1 000 THICK FLYWHEEL THINNER FLYWHEELS WILL MINIMIZE CLUTCH DISC ENGAGEMENT m ASS 6 I A AN2. N AX ZI m AAAA SA NEW GEAR 716016 IS ONLY AVALABLE WITH 17 TEETH SOME INSTALLATIONS MAY REQUIRE SHORTENING OF NEW BEARING RETAINER MAKE SURE RETAINER LEARENCE AND DOES NOT INTERFERE WITH CLUTCH HUB OR CLUTCH FINGERS s wr we at we ARM MOUNTS ON EITHER A BALL STUD OR AN ANGLE BRAKET NOTES Be sure to grease the inside pocket diameter of bearings This will provide lubrica tion on the bearing retainer Release bearing should have 060 clearance between fingers and face of bearing Clutch disc should have 030 clearance between flywheel and disc when fully disengaged RELEASE LEVER A A 716177 CLIP TYPE CLUTCH LEVER RETURN SPRING SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible warranty or return privileges If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores
3. ADVANCE ADAPTERS INC P N 712531 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 1 OF 2 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 11 07 07 SCOUT T19 4 SPEED TRANSMISSION TO FORD V8 amp AMC 304 BELLHOUSING KIT CONSISTS OF No Qty PartNo Description 1 1 711531 MODIFIED ADAPTER PLATE 712529 2 1 716016 17 TOOTH T18 INPUT SHAFT 3 14 716043 NEEDLE BEARINGS 4 1 716174 FORD AMC SPECIAL OD 670 ID 5 l 716732 SEAL National 471795 6 4 723119 S H C S 5 16 18 x 1 1 4 LONG 7 2 724309 H H C S 7 16 14 x 2 8 2 724328 H H C S 7 16 14x 1 1 4 LONG 9 4 725026 F H S C S 1 2 13 x 1 1 2 LONG 10 761019 FORD BEARING RETAINER 11 1 JPOOL JEEP INSTRUCTION MANUAL INSTALLATION PROCEDURES Assemble new input shaft into the transmission making sure that the proper pilot bearing area is used Some installations will require the use of the new needle bearings provided for the pocket area that fits over the main shaft Some installations will also require a different synchronizer ring The four studs protruding from the front of the Scout T19 transmission will need to be removed for the new flat head cap screws Before assembling the adapter plate to the front of the Scout transmission you must install the two 2 1 1 4 hex head bolts in the upper two bellhousing holes When assembling the adapter plate to the transmission make sure the seal properly fits over the ground surface of the input sh
4. aft It may be necessary to cheat the seal location outward in order to obtain the correct location You must use a silicone barrier to prevent oil leakage between the transmission face and adapter plate Bolt the new bearing retainer to the front of the adapter plate This retainer may need shortening on certain installations that are using the high diaphragm type clutch assemblies The shortening can be performed by removing the retainer and simply hack sawing it to the proper length A new input shaft must be installed If you are using this kit on a T98 transmission then the needle bearings inside the transmission input shaft will need to be changed and you must install the 14 new bearings included If the needle bearings are not changed then the new input shaft will not fit onto the main shaft If this kit is being used on a T18 or T19 transmission then the stock needle bearings will be retained The T18 T19 transmissions also used two sizes of shifter synchronizer rings If the transmission you have has a synchronizer ring that is too large you will then be required to purchase P N T98 83 from Border Auto Parts 619 461 0171 The Scouts have used two different thicknesses of front bearings our new input shaft requires a special narrow bearing This bearing was found on some stock transmission applications When your bearing while being installed on our input shaft does not allow the retaining snap ring to be installed on the input shaft then
5. you ll need to buy a new bearing BCA N 1308 LOB or AA P N 761093 The new two piece pilot bearing can now be installed into the engine crank This added length will make sure that the tip of the input shaft has proper engagement with the pilot bushing SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible warranty or return privileges If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores ADVANCE ADAPTERS INC P N 712531 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 2 OF 2 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 07 19 02 SCOUT T19 4 SPEED TRANSMISSION TO FORD V8 amp AMC 304 BELLHOUSING On Jeep vehicles that are retaining the original AMC 304 engine can use the Jeep bellhousing used on T150 applications 1976 through 1979 All of the original Jeep release arm and release bearing can be retained The pilot bushing will need to be a
Download Pdf Manuals
Related Search