Home
SunSwift SBus Adapter Installation and User`s Guide
Contents
1. VC CI VCCI X SunSwift SBus Adapter Installation and User s Guide January 1996 Preparing for Installation 1 The SunSwift SBus Adapter offers Fast Ethernet and FastWide SCSI 2 capabilities on
2. 2 At the ok prompt type ok boot full path name of the hme device 3 6 SunSwift SBus Adapter Installation and User s Guide January 1996 Qo lll 3 5 2 Diskless Client Booting for Solaris 2 4 In order to boot a diskless client with a local SunSwift SBus Adapter interface hme on a Solaris 2 4 system the following tasks must be performed on the boot server 1 Go to your client s root partition by typing the following cd export root lt client name gt etc 2 Edit the name_to_major file by adding an entry for the SunSwift SBus Adapter device hme If the major device number for the last file entry is n then use n 1 for the hme channel major device number As shown in the example below if the last entry for the major device number is 104 use 105 for the hme device gec 103 ge 104 hme 105 3 Copy the hme driver from the CD ROM to the client s root partition as follows cp cdrom sunswift_1_0 2 4 SUNWhmd reloc kernel drv hme export root lt client name gt kernel drv hme 4 Create a hostname hme lt num gt file for the client in the etc directory in the client s root partition Proceed to Section 3 5 3 Booting From the Network Using Solaris 2 4 for the client system Installing SunSwift SBus Adapter Software On Solaris 2 4 and 2 5 Systems 37 lll Qo 3 5 3 Booting From the Network Using Solaris 2 4 The device name of
3. Email address NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO 1 MOUNTAIN VIEW CA POSTAGE WILL BE PAID BY ADDRESSEE SUN MICROSYSTEMS INC Attn Manager Hardware Publications MS MPK 14 101 2550 Garcia Avenue Mt View CA 94043 9850
4. B 3 Performance Specifications Maximum Ethernet Transfer Rate Network Interface Ethernet Version SCSI Interface SBus Clock SBus Burst Sizes SBus Modes SBus Parity SBus Version 10 100 Mbps 100BASE TX using Category 5 data grade cable 10BASE T using Category 3 voice grade cable or better Conforms to IEEE 802 3u 20 Mbytes s 16 bit single ended 16 67 MHz to 25 MHz 16 32 64 bytes Master Slave 64 bit support Yes Conforms to IEEE 1496 B 1 B 2 SunSwift SBus Adapter Installation and User s Guide January 1996 Reader Comments We welcome your comments and suggestions to help improve this manual Please let us know what you think about the SunSwift SBus Adapter Installation and User s Guide part number 802 6021 10 The procedures were well documented Strongly Strongly Not Agree Agree Disagree Disagree Applicable Q Q Q Q Comments The tasks were easy to follow Strongly Strongly Not Agree Agree Disagree Disagree Applicable Q Q Q Q Q Comments The illustrations were clear Strongly Strongly Not Agree Agree Disagree Disagree Applicable Q Q Q Q Q Comments The information was complete and easy to find Strongly Strongly Not Agree Agree Disagree Disagree Applicable Q Q Q Q Q Comments Do you have additional comments about the SunSwift SBus Adapter Installation and User s Guide Name Title Company Address Telephone
5. Options Options Options zs0 sptest m audio0 autest Options SBUS DEVICES butwo0 fbtest USER TESTS Options user0 nettest Options Figure A 1 Sundiag Window Running Diagnostics for Solaris 2 4 A 1 3 Starting the Test 1 Review the information in the control panel which identifies the devices that are available for testing Click on the device that you want to test in this case USER 0 nettest Your selection is confirmed with the display of a highlighted box next to the device name 2 Click on the Start button 3 Watch the console window for messages 4 To interrupt a test or to stop after a test is completed click on the Stop button If no problems are identified during the testing the SunSwift SBus Adapter is ready for operation in your system Click on the Quit button to exit Sundiag SunSwift SBus Adapter Installation and User s Guide January 1996 Interface Signals B 1 SunSwift SBus Adapter Connectors O 1 8 1 34 O 0000000000000000000000000 O 0000000000000000000000000 M 7 35 68 Y RJ 45 Connector 68 pin SCSL2 Connector B 2 RJ 45 Connector Signals Pin Signal ON O1 amp ND eH Transmit Transmit Receive No Connection No Connection Receive No Connection No Connection B 1 B B 3 SCSI 2 Connector Signals B 2
6. Bourne shell and Korn shell superuser machine _name vi SunSwift SBus Adapter Installation and User s Guide January 1996 Related Documents The following documents contain topics that relate to the information in the SunSwift SBus Adapter Installation and User s Guide Title Part Number Your system installation or service manual Solaris 2 4 Handbook for SMCC Peripherals 801 6990 Solaris 2 5 Handbook for SMCC Peripherals 802 3725 SMCC Open Issues Supplement Solaris 2 4 802 2284 SMCC Open Issues Supplement Solaris 2 5 802 3708 SMCC Open Issues Supplement Solaris 2 5 Hardware 1 96 802 3740 Solaris 2 4 on Sun Hardware AnswerBook Solaris 2 5 on Sun Hardware AnswerBook SunVTS 1 0 User s Guide 801 7271 Platform Notes The hme Fast Ethernet Device Driver 802 3970 Ordering Sun Documents The SunDocs Order Desk is a distribution center for Sun Microsystems technical documents You can use major credit cards and company purchase orders You can order documents in the following ways In the U S A Outside the U S A Fax 1 801 373 6798 Fax 1 801 373 6798 Call 1 800 247 0250 Call 1 801 342 3450 World Wide Web http www sun com sundocs catalog html Preface vii Sun Welcomes Your Comments viii Please use the Reader Comment Card that accompanies this document We are interested in improving our documentation and welcome your comments and suggestions If a card is not available you can emai
7. Pin Signal Pin Signal 1 SCSI_GND 35 SCSI_D lt 12 gt _ 2 SCSI_GND 36 SCSI_D lt 13 gt _ 3 SCSI_GND 37 SCSI_D lt 14 gt _ 4 SCSI_GND 38 SCSI_D lt 15 gt _ 9 SCSI_GND 39 SCSI_DATA_PARITY1_ 6 SCSI_GND 40 SCSI_D lt 0 gt _ 7 SCSI_GND 41 SCSI_D lt 1 gt _ 8 SCSI_GND 42 SCSI_D lt 2 gt _ 9 SCSI_GND 43 SCSI_D lt 3 gt _ 10 SCSI_GND 44 SCSI_D lt 4 gt _ 11 SCSI_GND 45 SCSI_D lt 5 gt _ 12 SCSI_GND 46 SCSI_D lt 6 gt _ 13 SCSI_GND 47 SSCSI_D lt 7 gt _ 14 SCSI_GND 48 SCSI_DATA_PARITYO_ 15 SCSI_GND 49 SCSI_GND 16 SCSI_GND 50 SCSI_GND 17 SCSI_TERMPOWER 51 SCSI TERMPOWER 18 SCSI TERMPOWER 52 SCSI TERMPOWER 19 PULLUP 53 PULLUP 20 SCSI_GND 54 SCSI_GND 21 SCSI_GND 55 SCSI_ATN_ 22 SCSI_GND 56 SCSI_GND 23 SCSI_GND 57 SCSI_BSY_ 24 SCSI_GND 58 SCSI_ACK_ 25 SCSI_GND 59 SCSI_RST_ 26 SCSI_GND 60 SCSI_MSG_ 27 SCSI_GND 61 SCSI_SEL_ 28 SCSI_GND 62 SCSI_CD_ 29 SCSI_GND 63 SCSI_REO_ 30 SCSI_GND 64 SCSI_IO_ 31 SCSI_GND 65 SCSI_D lt 8 gt _ 32 SCSI_GND 66 SCSI_D lt 9 gt _ 33 SCSI_GND 67 SCSI_D lt 10 gt _ 34 SCSI_GND 68 SCSI_D lt 11 gt _ SunSwift SBus Adapter Installation and User s Guide January 1996 Specifications es lil B 1 Physical Characteristics Length 5 78 in 147 70 mm Width 3 3 in 83 82 mm Weight 4 0 oz 113 40 g B 2 Power Requirements Maximum Power Dissipation 9 5 Watt Power Consumption 0 9 Amps 5Volts Voltage Tolerance 5V 5 Ripple Maximum 100 mV Operational Current 1 9A
8. Type ok nvedit 3 Type the following pressing the Return key at the end of line 0 0 probe all install console banner 1 apply transfer speed 10 full path name of the hme device 4 Press the Control C keys after typing full path name of the hme device Note In the above example the speed is forced to 10 Mbps To force the speed to 100 Mbps replace 10 with 100 5 At the ok prompt type ok nvstore ok setenv use nvramrc true 6 Reboot your system Refer to the Platform Notes The hme Fast Ethernet Device Driver document Part No 802 3970 for more information on the hme device driver and forcing network speed This document is also available on the Solaris 2 5 and the Solaris 2 5 1 96 AnswerBook SunSwift SBus Adapter Installation and User s Guide January 1996 Qo lll 3 6 5 Auto Negotiation A key feature of the SunSwift SBus Adapter is auto negotiation The auto negotiation protocol as specified by the 100BASE T standard automatically selects the operation mode half duplex or full duplex and speed 10 Mbps or 100 Mbps for the adapter The hme device driver operates the SUNW hme device by default in half duplex mode only If the SunSwift SBus Adapter is connected to a remote system or interface that is not capable of auto negotiation your system automatically selects the speed and half duplex mode If the SunSwift SBus Adapter is connected to a link
9. etc hostname hmel zardoz 12 3 4 SunSwift SBus Adapter Installation and User s Guide January 1996 3 2 Create an appropriate entry in the etc hosts file for each active hme channel Using the example in step 1 you will have zardoz cat etc hosts 127 0 0 1 localhost 129 144 10 57 zardoz loghost 129 144 11 83 zardoz 11 129 144 12 41 zardoz 12 3 4 Caution Package Dependency Caution There is a package dependency with the SunSwift SBus Adapter Before proceeding perform the following task As superuser check for the adapter packages by using the pkginfo command pkginfo grep SUNWhmd If you see lines containing SUNWhmdl and SUNWhmdlu and lines containing SUNWhmd and SUNWhmdu then do not remove any of these packages from your system Installing SunSwift SBus Adapter Software On Solaris 2 4 and 2 5 Systems 35 3 3 5 Booting The following sections discuss various ways of booting See the section that applies to your specific needs 3 5 1 Booting From the Network Using Solaris 2 5 To use the SunSwift SBus Adapter Ethernet interface as the boot device for Solaris 2 5 systems perform the following tasks 1 At the ok prompt type ok show devs The show devs command lists the system devices You should see the full path name of the hme device similar to the example below iommu f e0000000 sbus f e0001000 SUNW hme 3 8c00000
10. m 68 pin to 68 pin cable Two SBus adapters maximum Tz SunSwift SBus Adapter Installation and User s Guide January 1996 lll SCSI Cabling You can daisy chain up to 15 devices on the SunSwift SBus Adapter as follows Wide to wide devices Use a 68 pin to 68 pin cable Always put wide SCSI devices closest to the host system Wide to narrow devices Use a 68 pin to 50 pin cable You can include only one wide to narrow cable along a chain of peripherals Always put the narrow SCSI devices at the end of the chain The SCSI bus must be terminated at the end of the chain Single byte data transfers from an odd memory address to a SCSI device are not supported by the SunSwift SBus Adapter SCSI 2 fas device Refer to SMCC Open Issues Supplement Solaris 2 5 Hardware 1 96 for more detailed information If you use the SunSwift SBus Adapter for SCSI purposes only you must change the device name from SUNW hme to SUNW hme_idle to avoid a Link Down cable problem message Refer to SMCC Open Issues Supplement Solaris 2 5 for more detailed information Ethernet Cabling An additional Ethernet cable is required if you want to use your system s existing Ethernet interface and the SunSwift SBus Adapter Ethernet interface Disabling Your Current Ethernet Device If you remove your system s existing Ethernet cable either from its on board Ethernet device or from an existing Ethernet card and insert it into
11. mettent en place les utilisateurs d interfaces graphiques OPEN LOOKet qui en outre se conforment aux licences crites de Sun Le syst me X Window est un produit du X Consortium Inc CETTE PUBLICATION EST FOURNIE EN L ETAT SANS GARANTIE D AUCUNE SORTE NI EXPRESSE NI IMPLICITE Y COMPRIS ET SANS QUE CETTE LISTE NE SOIT LIMITATIVE DES GARANTIES CONCERNANT LA VALEUR MARCHANDE L APTITUDE DES PRODUITS A REPONDRE A UNE UTILISATION PARTICULIERE OU LE FAIT QU ILS NE SOIENT PAS CONTREFAISANTS DE PRODUITS DETIERS kA Adobe PostScript Contents 1 Preparing for Installation EEE KS 00 75 1 1 LL Features norme eee 1 1 1 2 Requirements for Using the SBus Adapter 1 2 2 Installing the Adapter SS 2 1 2 1 Performing the Installation 2 a v ta css ee tae ves vive 2 1 2 2 Verifying the Installation ssns sunnan asee 2 2 2 3 Watching Network Activity 2 3 3 Installing SunSwift SBus Adapter Software On Solaris 2 4 and 2 5 Systems ses sseserus 3 1 3 1 Preparing for Software Installation 3 2 3 2 Net Install of Solaris 2 4 Over the hme Interface 3 3 3 3 Host File Configuration near mere 3 4 3 4 Caution Package Dependency eee 3 5 Ont BOON rers RE ei Vee 3 6 3 5 1 Booting From the Network Using Solaris 2 5 3 6 iii 3 5 2 Diskless Client Booting for Solaris 2 4 3 7 3 5 3 Booting From the Network Using Solaris 2 4 3 8
12. newer SBus cards for Solaris 2 5 is identified by a SUNW prefix If your system is running Solaris 2 4 it will not recognize the device Perform the following tasks to set up your system so the device driver can recognize the SunSwift SBus Adapter 1 At the ok prompt type ok setenv use nvramrc true ok show devs The show devs command lists the system devices You should see the full path name of the hme device similar to the example below iommu e0000000 sbus f e0001000 SUNW hme 3 8c00000 2 Type ok nvedit 3 Type the following exactly as shown spaces and quotation marks included pressing the Return key at the end of lines 0 1 and 2 probe all install console banner ed full path name of the hme device hme nameprop device end WN FO 4 Press the Control C keys after typing device end 5 At the ok prompt type ok nvstore ok reset Your system will reset and the banner will appear 3 8 SunSwift SBus Adapter Installation and User s Guide January 1996 Qo lll 6 Press the Stop A keys to get to the ok prompt 7 At the ok prompt type show devs to list your system devices and verify that the name property was changed correctly You should see the full path name of the hme device excluding SUNW prior to hme similar to the example below iommu f e0000000 sbus f e0001000 hme 3 8c00000 8 At
13. partner with which the auto negotiation protocol fails to operate successfully you can configure the device to not use this protocol and force the driver to set up the link in the mode and speed of your choice Refer to the Platform Notes The hme Fast Ethernet Device Driver document Part No 802 3970 for more information on the hme device driver and auto negotiation This document is also available on the Solaris 2 5 and the Solaris 2 5 1 96 AnswerBook Installing SunSwift SBus Adapter Software On Solaris 2 4 and 2 5 Systems 3 13 3 14 SunSwift SBus Adapter Installation and User s Guide January 1996 Running Diagnostics for Solaris2 4 A Note For Solaris 2 5 diagnostics testing refer to the SunVTS 1 0 User s Guide A 1 Sundiag Sundiag is an on line system exerciser that runs diagnostic hardware tests It is used primarily with the OpenWindows software interface that enables you to quickly and easily set test parameters to run tests Note Sundiag does not probe for SunSwift SBus Adapter devices by default For Sundiag to acknowledge an hme lt num gt channel the usertest file must be edited before bringing up Sundiag as described in the following section A 2 A 1 1 Editing usertest File 1 Login as superuser and then type the following zardoz cd opt SUNWdiag bin 2 Edit the file usertest by adding the following line wherein the format is test label test name and co
14. pre loaded with the SunSwift SBus Adapter driver hme Before installing the driver from the CD ROM perform the following task As superuser check for the hme driver and its revision number by using the modinfo command modinfo grep hme You should see a line similar to the example below if the driver is already installed 51 50270000 9f78 7 1 hme FEPS Ethernet Driver v 1 40 e If the revision number is 1 40 or above your system already has the SunSwift SBus Adapter driver and loading from the CD is unnecessary e If the revision number is below 1 40 or nothing is displayed as a result of the modinfo command install the software from the CD ROM that came with the SunSwift SBus Adapter See below Installing Software From the CD ROM for Solaris 2 4 and 2 5 Install the software drivers from the CD ROM that came with the SunSwift SBus Adapter Refer to the CD ROM documentation that came with your adapter for driver installation instructions Part No 804 5303 10 SunSwift SBus Adapter Installation and User s Guide January 1996 Qo lll 3 2 Net Install of Solaris 2 4 Over the hme Interface This section is only applicable if you are installing Solaris 2 4 on a net install client system over the SunSwift SBus Adapter hme interface Note The Solaris 2 4 CD ROM cannot be used to perform a net install read only thus the Solaris 2 4 CD image archive is required to u
15. the SUNW hme Ethernet device The device driver automatically selects the link speed using the auto negotiation protocol with the link partner See Section 3 6 5 Auto Negotiation You can manually configure the hme device driver parameters to customize each SUNW hme device in your system in one of three ways e Configure the hme driver parameters generally for all devices in the system by entering the parameter variables in the etc systen file Set a parameter on a per device basis by creating the hme conf file in the kernel drv directory Use the ndd utility to temporarily change a parameter This change is lost when you reboot the system 3 6 3 Increasing 100BASE T Performance The 100BASE T performance of the SunSwift SBus Adapter can be increased by changing the TCP hiwater marks to 64K This can be done with the nda utility as follows 1 As superuser type ndd set dev tcp tcp_xmit_hiwat 65535 ndd set dev tcp tcp_recv_hiwat 65535 ndd set dev tcp tcp_cwnd_max 65534 The changes will take effect immediately Installing SunSwift SBus Adapter Software On Solaris 2 4 and 2 5 Systems 3 11 3 12 3 6 4 Forcing Network Speed Between 10 Mbps and 100 Mbps 1 At the ok prompt use the show devs command to list the system devices You should see the full path name of the hme device similar to the example below iommu e0000000 sbus f e0001000 SUNW hme 3 8c00000 2
16. the SunSwift SBus Adapter Ethernet connection you must disable your current card s Ethernet device For example if your current Ethernet device is called 1e0 you would remove its IP address and hostname from the etc hosts file and remove the etc hostname 1e0 file itself Preparing for Installation 1 3 1 4 SunSwift SBus Adapter Installation and User s Guide January 1996 Installing the Adapter 2 This chapter tells you how to install the adapter in your system and verify that the adapter is correctly installed 2 1 Performing the Installation Note Refer to your system installation or service manual and the SCSI device installation manual as necessary for detailed instructions for the following tasks 1 Power off your system using the standard shutdown procedures described in Solaris 2 x Handbook for SMCC Peripherals 2 If you are replacing an SBus card with the SunSwift SBus Adapter remove the old card now 3 Install the SunSwift SBus Adapter in the selected SBus slot 4 Attach the SCSI cable to the 68 pin SCSI connector on the adapter and to the SCSI device if necessary Note Make sure you have an Ethernet cable for each interface 5 Connect the Ethernet cable to the SunSwift SBus Adapter RJ 45 connector and to the hub 2 1 2 2 2 Verifying the Installation 2 2 After the SunSwift SBus Adapter is installed and before booting the system verify installation by perfo
17. the ok prompt type ok boot full path name of the hme device Installing SunSwift SBus Adapter Software On Solaris 2 4 and 2 5 Systems 3 9 3 3 6 Post Installation Procedures Optional Perform the tasks in the following sections to verify and customize the performance of the SunSwift SBus Adapter 3 6 1 Using Hubs That Do Not Send Link Pulses Certain hubs are not compliant with the IEEE 802 3 Ethernet standards for link pulses therefore do not send link pulses To connect your system to these non compliant hubs you need to disable your system from looking for link pulses 1 At the ok prompt type ok show devs The show devs command lists the system devices You should see the full path name of the hme device similar to the example below iommu e0000000 sbus f e0001000 SUNW hme 3 8c00000 2 Type ok nvedit 3 Type the following pressing the Return key at the end of line 0 0 probe all install console banner 1 apply disable link pulse full path name of the hme device 4 Press the Control C keys after typing full path name of the hme device 5 At the ok prompt type ok nvstore ok setenv use nvramrc true 6 Reboot your system 3 10 SunSwift SBus Adapter Installation and User s Guide January 1996 Qo lll 3 6 2 Configuring Driver Parameters The hme device driver which is loaded from the CD ROM controls
18. the same SBus card SBus connector GE scsr2 Se connector Ethernet 1 1 Features This SBus card offers the following features e Switchable 10BASE T 100BASE TX Ethernet Automatically sets 10 100 Mbps speed Conforms to IEEE 802 3u Ethernet standard e 20 Mbytes s 16 bit single ended SCSI 2 controller Conforms to ANSI X3T9 2 SCSI 2 standard SBus interface to host system Complies with IEEE 1496 SBus specification 1 1 lll 1 2 Requirements for Using the SBus Adapter Before installing the adapter make sure your system meets the following hardware and software requirements Hardware Requirements Software Requirements Supported Platforms Firmware Peripherals SCSI Cables Part Numbers Sun SPARCstation systems with an available SBus slot Solaris 2 4 Solaris 2 5 or later Solaris 2 x release Solaris 2 4 SPARCstation 5 SPARCstation 10 SPARCstation 20 SPARCserver 1000 1000E SPARCcenter 2000 2000E SPARCserver 6x0MP Solaris 2 5 Sun Ultra systems SPARCstation 5 SPARCstation 10 SPARCstation 20 SPARCserver 1000 1000E SPARCcenter 2000 2000E SPARCserver 6x0MP OpenBoot PROM Version 2 9 or greater Only Sun SCSI 2 devices Only standard Sun supported cabling to ensure reliable SCSI interface connections 530 2115 02 1 2 m 50 pin to 68 pin cable 530 1884 03 0 8 m 68 pin to 68 pin cable 530 2228 01 2 m 50 pin to 68 pin cable 530 1885 03 2
19. 3 6 Post Installation Procedures Optional 3 10 3 6 1 Using Hubs That Do Not Send Link Pulses 3 10 3 6 2 Configuring Driver Parameters 3 11 3 6 3 Increasing 100BASE T Performance 3 11 3 6 4 Forcing Network Speed Between 10 Mbps and 100 Mbps 3 12 3 6 5 Auto Negotiation SNS 3 13 Running Diagnostics for Solaris 2 4 A 1 Al Sundi g sr ce kee etates a E EE E A 1 A 1 1 Editing usertest File ayaccevere re ee ees eos A 2 A 1 2 The Sundiag Window en A 2 A 139 Starting the Test sono ER A 4 Interface Sionals so ieee to ea B 1 B 1 SunSwift SBus Adapter Connectors B 1 B 2 RJ 45 Connector Signals ini each B 1 B 3 SCSI 2 Connector Signals Le B 2 Specifications 24e ra ce SSS 0 C 1 C 1 Physical Characteristics 0 secleies eaten dee Cae es C 1 C 2 Power Requirements yos C 1 C 3 Performance Specifications Eee ee C 1 SunSwift SBus Adapter Installation and User s Guide January 1996 UNIX Commands Preface This manual describes how to install and use your SBus card The procedures in this manual assume that you are a system or network administrator experienced in installing similar hardware and that you are familiar with Solaris administration This document may not include specific software commands or procedures Instead it may name software tasks and refer you to operating system documentation or the handbook that was shipped with your new hardware The ty
20. SunSwift SBus Adapter Installation and User s Guide RN amp SUN The Network Is the Computer Sun Microsystems Computer Company 2550 Garcia Avenue Mountain View CA 94043 USA 415 960 1300 fax 415 969 9131 Part No 802 6021 10 Revision A January 1996 Please Recycle Copyright 1996 Sun Microsystems Inc 2550 Garcia Avenue Mountain View California 94043 1100 U S A All rights reserved This product or document is protected by copyright and distributed under licenses restricting its use copying distribution and decompilation No part of this product or document may be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Portions of this product may be derived from the UNIX system and from the Berkeley 4 3 BSD system licensed from the University of California UNIX is a registered trademark in the United States and in other countries and is exclusively licensed by X Open Company Lt d Third party software including font technology in this product is protected by copyright and licensed from Sun s suppliers RESTRICTED RIGHTS LEGEND Use duplication or disclosure by the government is subject to restrictions as set forth in subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 and FAR 52 227 19 Sun Sun Microsystems the Sun logo and Solaris are trademarks or registered trademarks of Sun Microsystems Inc in the
21. United States and in other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the United States and in other countries Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems Inc The OPEN LOOK and Sun Graphical User Interfaces were developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees who implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements X Window System is a trademark of X Consortium Inc THIS PUBLICATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT Copyright 1996 Sun Microsystems Inc 2550 Garcia Avenue Mountain View Californie 94043 1100 U S A Tous droits r serv s Ce produit ou document est prot g par un copyright et distribu avec des licences qui en restreignent l utilisation la copie et la d compilation Aucune partie de ce produit ou de sa documentation associ e ne peut tre reproduite sous aucune forme par que
22. l or fax your comments to us Please include the part number of your document in the subject line of your email or fax message e Email smcc docs sun com e Fax SMCC Document Feedback 1 415 786 6443 SunSwift SBus Adapter Installation and User s Guide January 1996 A FCC Class B Notice United States This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed an used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipme
23. lque moyen que ce soit sans l autorisation pr alable et crite de Sun et de ses bailleurs de licence s il y ena Des parties de ce produit pourront tre deriv es du syst me UNIX et du syst me Berkeley 4 3 BSD licenci par l Universit de Californie UNIX est une marque enregistr e aux Etats Unis et dans d autres pays et licenci e exclusivement par X Open Company Ltd Le logiciel d tenu par des tiers et qui comprend la technologie relative aux polices de caract res est prot g par un copyright et licenci par des fournisseurs de Sun Sun Sun Microsystems le logo Sun et Solaris sont des marques d pos es ou enregistr es par Sun Microsystems Inc aux Etats Unis et dans d autres pays Toutes les marques SPARC utilis es sous licence sont des marques d pos es ou enregistr es de SPARC International Inc aux Etats Unis et dans d autres pays Les produits portant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc Les utilisateurs d interfaces graphiques OPEN LOOK et Sun ont t d velopp s de Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconna t les efforts de pionniers de Xerox pour la recherche et le d veloppement du concept des interfaces d utilisation visuelle ou graphique pour l industrie de l informatique Sun d tient une licence non exclusive de Xerox sur l interface d utilisation graphique cette licence couvrant aussi les licenci s de Sun qui
24. mmand line arguments The example given is for a single hme0 interface for multiple channels add an additional line for each channel using hme1 hme2 etc hme0 nettest IF hme0 v Because testing the SunSwift SBus Adapter is user defined default options are not displayed in Sundiag Test options for an hme lt num gt channel can be defined in the usertest file using the command nettest Type the command nettest without arguments for a list of options for example zardoz nettest Usage nettest TARGET h1 h2 IF interface TEST 0 7 N nopkts P pattern T seconds A 1 2 The Sundiag Window Note Examples in this section show Sundiag running in the OPEN LOOK environment Sundiag run in the SunView environment will look different To start Sundiag cd to the Sundiag directory opt SUNWdiag bin sundiag and then type the sundiag command After you enter the sundiag command the Sundiag window is displayed on your screen refer to Figure A 1 This window is the primary interface for running Sundiag Refer to the Sundiag manual that came with your operating system for further details SunSwift SBus Adapter Installation and User s Guide January 1996 A The Sundiag window is divided into four small windows The system status window at the upper left of the screen displays the status of the tests The performance monitor panel in the upper middle of the screen displays
25. nt and receiver e Connect the equipment into a power outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio television technician for help Shielded Cables Connections between the workstation and peripherals must be made using shielded cables in order to maintain compliance with FCC radio frequency emission limits Modifications Modifications to this device not approved by Sun Microsystems Inc may void the authority granted to the end user by the FCC to operate the equipment DOC Class B Notice Canada This digital apparatus does not exceed Class B limits for radio noise emission for a digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications Avis Concernant les Syst mes Appartenant la Classe B du DOC Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe B prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada Preface ix VCOI VD VC CI VCD
26. or incoming network packets by typing watch net all ok watch net all iommu f e0000000 sbus f e0001000 SUNW hme 3 8c00000 Internal loopback test succeeded Transceiver check Using Onboard Transceiver Link Up passed Using Onboard Transceiver Link Up Looking for Ethernet Packets is a Good Packet X is a Bad Packet Type any key to stop Note The network speed is the same as the speed of the hub to which your system is connected See Chapter 3 Section 3 6 Post Installation Procedures Optional for more detailed information on speed selection Where to Proceed e See Chapter 3 Installing SunSwift SBus Adapter Software On Solaris 2 4 and 2 5 Systems Installing the Adapter 23 2 4 SunSwift SBus Adapter Installation and User s Guide January 1996 Installing SunSwift SBus Adapter Software On Solaris 2 4and 2 5 Systems 3 This chapter describes SunSwift SBus Adapter software installation requirements for Solaris 2 4 and 2 5 software versions only Note You must have already installed the SunSwift SBus Adapter in your system prior to performing the following tasks 3 1 3 3 1 Preparing for Software Installation 3 2 Note If the CD ROM drive that you are using for software installation is attached to a remote machine refer to your SunOS installation guide for remote CD ROM access For Solaris 2 5 Systems Some newer systems are
27. pdate certain SunSwift SBus Adapter files Updating the Solaris 2 4 Archive to Use the hme Interface 1 Determine the directory where the CD image is located on the boot server For example if the Solaris software is located within a directory named DIR change to the root partition of the client being installed by typing cd DIR export exec kvm lt archive_of_arch gt etc The etc bootparams file will point you to the client s root partition 2 Edit the name_to_major file by adding an entry for the SunSwift SBus Adapter device hme If the major device number for the last file entry is n then use n 1 for the hme channel major device number As shown in the example below if the last entry for the major device number is 108 use 109 for the hme device llcl 107 audiocs 108 hme 109 3 Copy the hme driver from the SunSwift SBus Adapter CD ROM to the client s root partition as follows cp cdrom sunswift_1_0 2 4 SUNWhmd reloc kernel drv hme DIR export exec kvm lt archive_of_arch gt kernel drv 4 On the client system perform the tasks in Section 3 5 3 Booting From the Network Using Solaris 2 4 Installing SunSwift SBus Adapter Software On Solaris 2 4 and 2 5 Systems 33 lll Qo 5 6 7 Complete the client installation Refer to your Solaris documentation for detailed instructions Reboot the system Install the software drivers from the CD ROM tha
28. pe of information that you might need to use references for includes e Shutting down the system Booting the system e Configuring devices e Other basic software procedures See one or more of the following e Solaris 2 x Handbook for SMCC Peripherals contains Solaris 2 x software commands On line AnswerBook for the complete set of documentation supporting the Solaris 2 x software environment e Other software documentation that you received with your system Typographic Conventions The following table describes the typographic changes used in this book Typeface or Symbol Meaning Example AaBbCc123 AaBbCc123 AaBbCc123 AaBbCc123 The names of commands files and directories on screen computer output What you type contrasted with on screen computer output Command line placeholder replace with a real name or value Book titles new words or terms or words to be emphasized Edit your login file Use ls a to list all files machine_name You have mail machine_name su Password To delete a file type rm filename Read Chapter 6 in the User s Guide These are called class options You must be root to do this Shell Prompts The following table shows the default system prompt and superuser prompt for the C shell Bourne shell and Korn shell Shell C shell C shell superuser Prompt machine_name Bourne shell and Korn shell
29. rming the following tasks Refer to the Solaris 2 x Handbook for SMCC Peripherals manual or your Solaris documentation for the detailed instructions 1 Power on the system and when the banner appears press the Stop A keys to interrupt the boot process and to get to the ok prompt 2 Use the show devs command to list the system devices You should see a line similar to the one in the example below in the display specific to the SunSwift SBus Adapter ok show devs iommu e0000000 sbus f e0001000 SUNW fas 0 8800000 iommu e0000000 sbus f e0001000 SUNW hme 0 8c00000 e fas 0 identifies the adapter s SCSI 2 device hme 0 identifies the adapter s Ethernet device Note In the above example the number 0 following fas and hme corresponds to the SBus slot in which the SunSwift SBus Adapter resides If you do not see these devices listed check that the adapter is properly seated and reinstall the adapter if necessary Diagnostics Testing For SunSwift SBus Adapter diagnostics testing on systems running Solaris 2 4 see Appendix A Running Diagnostics for Solaris 2 4 e For SunSwift SBus Adapter diagnostics testing on systems running Solaris 2 5 refer to the SunVTS 1 0 User s Guide SunSwift SBus Adapter Installation and User s Guide January 1996 No lll 2 3 Watching Network Activity Make sure that you are connected to an active network You can watch network activity
30. t came with the SunSwift SBus Adapter Refer to the CD ROM documentation that came with your adapter for driver installation instructions Part No 804 5303 10 3 3 Host File Configuration After installing the SunSwift SBus Adapter software you must create a hostname hme lt num gt file for its Ethernet interface You must also create both an IP address and a hostname for its Ethernet interface in the etc hosts file To prepare your system for the SunSwift SBus Adapter 1 Create a etc hostname hme lt num gt file where lt num gt refers to the number of each SunSwift SBus Adapter channel you plan to use For example use channel hme0 for the first card use channel hme1 for a second card Do not create etc hostname hme lt num gt files for SunSwift SBus Adapter channels you plan to leave unused The etc hostname hme lt num gt file must contain the hostname for the appropriate network interface The hostname should have an IP address and should be entered in the etc hosts file The hostname should be different from any other hostname of any other interface for example etc hostname le0 and etc hostname hme0 cannot share the same hostname Following is an example of the etc hostname hme lt num gt files required for a machine called zardoz that will be known as zardoz 11 and zardoz 12 on the networks connected to the hme0 and hme1 Ethernet interfaces zardoz cat etc hostname hme0 zardoz 11 zardoz cat
31. the performance statistics for the system that is under test The control panel is located at the right The panel includes buttons exclusive choice toggle and pop up menus that allow you to select test parameters and options The console window at the bottom left displays test messages and allows you as a superuser to use operating system commands SunDiag Version 4 3 Hostname mouse Model Sun 4_25 System status idle Total errors 0 Elapsed time 000 00 00 System passes 0 MEMORY DEVICE TESTS mem pmem kmem vmem DISK DEVICE TESTS cOt3d0 rawtest cOt3d0 fstest cot6d0 cdtest CPU DEVICE TESTS fpu fputest led nettest audio0 autest SBUS DEVICE TESTS bwtwo0 fbtest USER TESTS user0 nettest passes passes passes passes passes passes passes passes passes passes 0 0 0 1 of 1 cpu errors 0 pkts errors 0 errors 0 ER errors 0 errors 0 sue errors 0 errors 0 intr errors 0 errors 0 disk errors 0 cntxt load colls errs mouse ibe Start Reset Print Set Options Schedule Log Files Option Files Status View 7 Intervention Enable Test Default None All MEMORY DEVICES men pmem CDI Options kmem vmem Options cOt3d0 rawtest cOt3d0 fstest cot6d0 cdtest fpu fputest le0 nettest Options Options Options
Download Pdf Manuals
Related Search
Related Contents
MV 300 MV 450 MV 600 MV 800 MV 1000 NEW 105 E NEW 105 S Philips Cleaning kit SVC1212 Paravox VD710 : User Guide dLAN 200 AVpro Wireless N.book ミオレット・フォーユー(2013/12~ ) Harbor Freight Tools 1250 Lb Capacity Low Profile Motorcycle Dolly Product manual Georgia-Pacific ` FICHE TECHNIQUE Approbation : istruzioni per l·installazione dei compressori semiermetici per co2 Copyright © All rights reserved.
Failed to retrieve file