English - Service
Contents
1. Attaching the hose Fig K Press in the clips 28 on either side of the hose 27 Press the hose 27 onto the steam nozzle 4 and release the clips 28 Important Ensure that the hose 27 is securely fastened before using the hand held steam cleaner If steam escapes from the joint then the hose is not correctly fit allow the unit to cool then remove and re fit the hose Attaching the variable steam jet nozzle Fig L Press in the clips 30 on either side of the variable steam jet nozzle 31 Press the variable steam jet nozzle onto the steam nozzle 4 or the hose 27 and release the clips 30 Important Ensure that the variable steam jet nozzle 31 is securely fastened before using the hand held steam cleaner If steam escapes from the joint then the variable steam jet nozzle is not correctly fit allow the unit to cool then remove and re fit the variable steam jet nozzle Attaching other accessories Fig J Align the lugs on the hose with the recesses on the acces sory Press the accessory 29 onto the hose 27 and twist anti clockwise until the accessory clicks into place Note The variable steam jet nozzle may be used without the hose by fitting them directly to steam nozzle All other acces sories must be connected to the hose for use Removing the hose and accessories Fig K amp L Warning The Steam nozzle variable steam jet nozzle hose and accessories become hot during use Allow the unit a2. fitted with an Autoselect button 6 which shows various cleaning applications They are used to select the correct operating mode for your particular cleaning operation Using Autoselect choose from one of the following applica tions by pressing the autoselect button 6 until the required setting is selected EN i Tiles Vinyl The steam mop will select the correct volume of steam required for your particular cleaning operation Note Always check you are using the correct setting before using your steam mop For convenience the steam mop will remember the last setting you chose Steam burst Fig The steam mop is equipped with a steam burst button to aid in the removal of stubborn marks and stains During use press the steam burst button 25 to apply extra cleaning power Note The steam burst will last for 10 seconds then the steam mop will return to the chosen setting Switching on and off Hand held steam cleaner Fig M To switch the appliance on press the ON OFF button 1 It takes approximately 15 seconds for the hand held steam cleaner to heat up Note When the hand held steam cleaner is first turned on the water reservoir will glow red Once the hand held steam cleaner is ready to use the water reservoir will glow blue Lift the lock off switch 2 and pull the trigger switch 3 After a few seconds steam will be produced To switch the appliance off release the trigger switch 3 t
3. BLACK DECKER FSMH1621S www blackanddecker co uk FSMH16151 Intended use Your BLACK DECKER steam mop has been designed for sanitising and cleaning sealed hardwood sealed laminate linoleum vinyl ceramic tile stone and marble floors and for refreshing carpets This appliance is intended for indoor household use only Features This appliance includes some or all of the following features 1 ON Off switch Lock off button Trigger switch Steam nozzle Hand held steam cleaner Autoselect button Filler cap Water tank 9 Steam mop body 10 Handle 11 Steam head 12 Steam head cleaning pad 14 Carpet glider 15 Bottom cable tidy hook 16 Top cable tidy hook 17 Cable management clip Warning Read all of the Safety Maintenance Service manual carefully before operating this appliance Read all of this manual carefully before operating the appliance WP Assembly Warning Before attempting any of the following operations make sure that the appliance is switched off and unplugged and that the appliance is cold and does not contain any water Attaching the handle Fig A Slide the bottom end of the handle 10 into the top end of the steam mop body 9 until it clicks i
4. connect the unit from the mains supply Allow to cool Remove the hand held steam cleaner from the steam mop body Inspect the seal 26 on the steam nozzle 4 and hose 27 fig K If the seal is missing or damaged then please contact your nearest authorised repair agent Do not use the appliance If the seal is in good condition re fit the hand held steam cleaner to the steam mop body ensuring that itis seated firmly in place Caution It is important to monitor the water level in the water tank To refill the water tank and continue to sanitise clean re turn the handle 10 to the upright position and turn the steam mop OFF Unplug the unit from the electrical wall outlet refill the water tank 8 Caution Never leave the steam mop in one spot on any surface for any period of time Always place the steam mop with the handle 10 in the upright position when stationary and make sure the steam mop is turned off when not in use After use Fig N amp O Return the handle 10 to the upright position and turn the steam mop OFF Wait until the steam mop cools down approximately five minutes Unplug the steam mop from the electrical wall outlet Empty the water tank 8 Remove the cleaning pad 12 and wash it ready for next use Take care to follow the wash care instructions printed on the cleaning pad Wrap the supply cable around the cable tidy hooks 15 16 Note The top cable tidy hook 16 rotates t
5. d off when not in use Carpet refreshing Place a cleaning pad 12 on the floor with the hook amp loop side facing up Lightly press the steam mop down onto the cleaning pad 12 Place the carpet glider 14 on the floor Lightly press the steam mop down onto the carpet glider 14 until it clicks into place Connect the steam mop to the mains Press the ON OFF button 1 It takes approximately 15 seconds for the steam mop to heat up Press the Autoselect button 6 to the Wood Laminate setting Pulling the handle 10 back will activate the steam pump After a few seconds steam will start to come out of the steam head Note When first filled or after running dry it can take up to 45 seconds for steam to be produced Push and pull the steam mop slowly across the carpet to thoroughly refresh each section Note During use you may turn off the steam pump by return ing the handle to the upright position this convenient feature will allow you to leave the steam mop for a short time so that you may move items of furniture then continue cleaning without the need to switch the appliance off When you have finished using the steam mop return the handle 10 to the upright position and turn it OFF and wait until the steam mop cools down approximately five minutes Caution If steam is observed escaping from the join between the hand held steam cleaner and the steam mop body switch off and dis
6. e carpet glider 14 until it clicks into place Caution Always place your steam mop with the handle 10 in the upright position when stationary and make sure the steam mop is turned off when not in use Removing the carpet glider Fig G Caution Always wear suitable shoes when changing the carpet glider on your steam mop Do not wear slippers or open toed footwear Return the handle 10 to the upright position and turn the steam mop OFF Wait until the steam mop cools down approximately five minutes Place the front of your shoe onto the carpet glider removal tab 22 and press down firmly Lift the steam mop up off the carpet glider 14 Caution Always place your steam mop with the handle 10 in the upright position when stationary and make sure the steam mop is turned off when not in use Fitting a scent pack Fig amp J Warning Return the handle 10 to the upright position and turn the steam mop OFF Wait until the steam mop cools down approximately five minutes Slide the door release button 35 the door will open Place the scent pack into the cavity 36 Close the door 37 py pushing it firmly down Attaching the hose and accessories to the Hand held steam cleaner Fig K 8 L Warning Inspect the seal 26 on the steam nozzle 4 and hose 27 before each use If the seal is missing or damaged then please contact your nearest authorised repair agent Do not use the appliance
7. eing produced he steam burst button 25 to temporarily increase the amount of steam he hand held steam cleaner has a lock off feature Lift the lock off switch 2 and pull the trigger switch 3 After a few seconds will be produced steps 8 then 1 then 2 then 3 he hand held steam cleaner will begin to produce steam after 15 seconds and will reach maximum steam flow after 45 seconds Firmly press the hand held steam cleaner release button 20 down then pull the hand held steam 5 cleaner from the steam mop body 9 gt Original instructions Possible solutions Refer to the assembly chapter of the manual Problem The accessories keep falling off the for correct fitting instructions of all parts and accessories unit Steam is escaping Refer to the assembly chapter of the manual from unexpected for correct fitting instructions of all parts and areas of the unit accessories Where can get www blackanddecker co uk steammop further information www blackanddecker ie steammop l accessories for my steam mop Australia Black amp Decker Australia Pty Ltd Tel 03 8720 5100 20 Fletcher Road Mooroolbark Fax 03 9727 5940 Victoria 3138 New Zealand Black amp Decker Tel 64 9 259 1133 5 Te Apunga Place Fax 64 9 259 1122 Mt Wellington Aukland 1060 United Kingdom amp Black amp Decker Tel 01753 511234 Republic Of Ireland 210 Bath Road Fax 01753 512365 ww
8. he handle 10 back will activate the steam pump After a few seconds steam will start to come out of the steam head Note When first filled or after running dry it can take up to 45 seconds for steam to be produced Ittakes a few seconds for steam to enter the cleaning pad The steam mop will now glide easily over the surface to be sanitised cleaned Push and pull the steam mop slowly across the floor to thoroughly steam clean each section Note During use you may turn off the steam pump by return ing the handle to the upright position this convenient feature will allow you to leave the steam mop for a short time so that you may move items of furniture then continue cleaning without the need to switch the appliance off gt Original instructions When you have finished using the steam mop return the handle 10 to the upright position and turn it OFF and wait until the steam mop cools down approximately five minutes Caution It is important to monitor the water level in the water tank To refill the water tank and continue to sanitise clean re turn the handle 10 to the upright position and turn the steam mop OFF Unplug the unit from the electrical wall outlet refill the water tank 8 Caution Never leave the steam mop in one spot on any surface for any period of time Always place the steam mop with the handle 10 in the upright position when stationary and make sure the steam mop is turne
9. hen press the ON OFF button 1 Caution Always empty the hand held steam cleaner after use Original instructions gt Caution Steam may continue to be produced for a short time after the trigger switch 3 is released this is normal Switch off and allow the unit to cool before removing any accessories Hints for optimum use General Caution Never use the steam mop without first attaching a cleaning pad During steam mop use you can use the cable manage ment clip 17 to keep your cable out of the way of the work area Always vacuum or sweep the floor before using the steam mop The easiest way to use the machine is to tilt the handle to a 45 angle and clean slowly covering a small area at a time Do not use chemical cleaners with your steam mop To remove stubborn stains from vinyl or linoleum floors you can use the steam burst button to apply extra steam to the area or pre treat with a mild detergent and some water before using the steam mop Steam cleaning with the mop Fit hand held steam cleaner 5 to the steam mop body 9 Place a cleaning pad 12 on the floor with the hook amp loop side facing up Lightly press the steam mop down onto the cleaning pad 12 Connect the steam mop to the mains Press the ON OFF button 1 It takes approximately 15 seconds for the steam mop to heat up Press the Autoselect button 6 till the required setting is reached Pulling t
10. nd all accessories to cool before removing any accessories Removing an accessory Fig K Twist the accessory 29 clockwise then pull away from the hose 27 Removing the hose Fig K Press in the clips 29 on either side of the hose 27 and pull away from the steam nozzle 4 Removing the variable steam jet nozzle Fig L Press in the clips 30 on either side of the variable steam jet nozzle 31 and pull away from the steam nozzle 4 Use Important This unit will kill 99 9 of bacteria amp germs when used in accordance with this manual and with the micro fibre pad fitted and a continuous run time of 90 seconds Switching on and off Steam mop To switch the appliance on press the ON OFF button 1 It takes approximately 15 seconds for the steam mop to heat up Note When the steam mop is first turned on the water res ervoir will glow red Once the steam mop is ready to use the water reservoir will glow blue To switch the appliance off press the ON OFF button 1 c 0000 Caution Never leave the steam mop in one spot on any surface for any period of time Always place the steam mop with the handle 10 in the upright position when stationary and make sure the steam mop is turned off when not in use Caution Always empty the steam mop after use Note When first filled or after running dry it can take up to 45 seconds for steam to be produced Autoselect Technology Fig This steam mop is
11. nto place The arrow on the handle 10 should be aligned with the top of the steam mop body 9 Attaching the steam head Fig B Slide the bottom end of the steam mop body 9 onto the steam head 11 until it clicks into place The steam head can be removed from the Steam mop body by pressing the steam head release button 19 and pulling the steam mop body 9 off the steam head 11 Original instructions gt Attaching the hand held steam cleaner Fig C Holding the back of the steam mop body 9 Push the hand held steam cleaner 5 firmly into the steam mop body 9 until it clicks into place Caution Always ensure the handle command lights up to confirm the unit is docked Warning Inspect that the seal 26 Fig J on the steam nozzle 4 before fitting the hand held steam mop to the steam mop body If the seal is missing or damaged then please contact your nearest authorised repair agent Do not use the appli ance Removing the hand held steam cleaner Fig C Push the release button 20 down and pull the hand held steam cleaner 5 away from the steam mop body Attaching a cleaning pad Fig D Replacement cleaning pads are available from your BLACK DECKER dealer Steam head cleaning pad 12 cat no FSMP20 XJ Place a cleaning pad 12 on the floor with the hook amp loop side facing up Lightly press the steam mop down onto the cleaning pad 12 Caution Always place your steam mop with
12. o easily release the cable ready for next use Clip the supply cable onto itself using the cable tidy clip 32 close to the plug Note With the handle 10 in the upright position the cable neatly wrapped around the cable tidy hooks 15 amp 16 and secured with the cable tidy clip 32 your steam mop will stand on its own for storage Alternatively there is a hanging bracket 33 built into the hand grip 34 which will allow your steam mop to be hung from a suitable hook on the wall Always ensure that your wall hook is capable of supporting the weight of the steam mop safely Hand held steam cleaning Attach the required accessory Connect the hand held steam cleaner to the mains Press the ON OFF button 1 It takes approximately 15 seconds for the hand held steam cleaner to heat up Lift the lock off 2 and pull the trigger switch 3 to activate the steam pump After a few seconds steam will start to come out of the accessory Note When first filled or after running dry it can take up to 45 seconds for steam to be produced Note During use you may turn off the steam pump by releas ing the trigger switch this convenient feature will allow you to place the hand held steam cleaner down for a short time so that you may move items of furniture then continue cleaning without the need to switch the appliance off Original instructions gt Possible solutions Check that the handle 10 of the steam mop is pushed fi
13. rmly into the steam mop body 9 with When you have finished using the hand held steam cleaner release the trigger switch 3 turn it OFF and disconnect from the mains supply Wait until the steam mop cools down before storing approximately five minutes Caution It is important to monitor the water level in the water tank To refill the water tank and continue to sanitise clean turn the hand held steam cleaner OFF Unplug the unit from the electrical wall outlet refill the water tank 8 Caution Steam may continue to be produced for a short time after the trigger switch 3 is released this is normal Switch off and allow the unit to cool before removing any accessories The digital controls do not light up The steam mop is not producing steam Accessories The performance of your appliance depends on accessory used BLACK DECKER accessories are engineered to high quality standards and designed to enhance the performance of your appliance By using these accessories you will get the very best from your appliance Technical data The digital controls FSMH16151 go out during use Type 1 The steam mop steam during use W frome 1600 1600 The steam mop is Tank capacity 350 350 producing too much steam during 5 Troubleshooting The steam mop is If your appliance seems not to operate properly follow the producing too little instruc
14. the handle 10 in the upright position when stationary and make sure the steam mop is turned off when not in use Removing a cleaning pad Fig E Caution Always wear suitable shoes when changing the cleaning pad on your steam mop Do not wear slippers or open toed footwear Return the handle 10 to the upright position and turn the steam mop OFF Wait until the steam mop cools down approximately five minutes Place the front of your shoe onto the cleaning pad removal tab 21 and press down firmly Lift the steam mop up off the cleaning pad Caution Always place your steam mop with the handle 10 in the upright position when stationary and make sure the steam mop is turned off when not in use Filling the water tank Fig F This Steam cleaner incorporates an anti calc system to help prolong the life of the system Note Fill the water tank with clean tap water Note In areas of very hard water the use of de ionised water is recommended Open the filler cap 7 by flipping it down Fill the water tank 8 with water Warning Your water tank has a 0 36 litre capacity Re fit the filler cap 7 gt Original instructions Note Ensure the filler cap is firmly secured Note Do not use chemical cleaners with your steam mop Attaching the carpet glider Fig G For use on carpets only Place carpet glider on the floor Attach a cleaning pad to the unit Lightly press the steam mop down onto th
15. tions below Ifthis does not solve the problem please steam during use contact your local BLACK DECKER repair agent Pi not turning on socket produced from the off switch 1 cleaner when the trigger is pulled EM Check the fuse in the plug The hand held steam cleaner is 1 ol T si 1 producing too little steam during use The hand held steam cleaner will not come out from the steam mop body is firmly docked into the steam body 9 Check steps 1 then 2 then 3 The steam mop will only produce steam once upright position heci Check that the Steam head 11 is firmi docked into the steam mop body 9 Check steps 5 then 1 then 2 then 3 Check steps 4 then 5 then 1 then 2 then 3 Check steps 7 then 8 then 9 then 5 autosel eam heck autosel steal Press eam heck that the arrow on the handle is flush he top of the steam mop body 9 that the hand held steam cleaner 5 he handle is pulled back from the that the water tank 8 is full NOTE When first filled or after running dry it can take up to 45 seconds for steam to be produced he steam mop has 3 settings Press the lect button 6 to reduce the amount of being produced hat the steam burst button 25 has not been pressed he steam mop has 3 settings Press the lect button 6 to increase the amount b
16. w blackanddecker co uk emeaservice sbdinc com Slough Berkshire SL1 3YD 90615612 REV 0 06 2014
Download Pdf Manuals
Related Search