P1800 Installation Manual
Contents
1. CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons intended to alertthe user to presence of important operating and maintenance servicing instructions in the literature The exclamation point within an equilateral triangle is accompanying the appliance SERVICE If the unit ever needs repair service customer should contact Videolarm 1 800 554 1124 for return authorization amp shipping instructions TECHNICAL SUPPORT Videolarm has set up a 24 hour technical support line for their customers 24 HOUR TECHNICAL SUPPORT 1 800 554 1124 VIDEOLARM INC warrants this Product to be free from defects in material or workmanship as follows PRODUCT CATEGORY PARTS LABOR All Enclosures and Electronics Five 9 Years Five 5 Years Pan Tilts Three 3 Years 6 months if used in autoscan Three 3 Years 6 months if used in autoscan Poles PoleEvators Three 3 Years four operation Three 3 Years tour operation Warrior Q View I R Illuminators Five 5 Years Five 5 Years View Series Five 5 Years 6 months if used in autoscan Five 5 Years 6 months if used in autoscan Con2. Cross Strap Place Hex Nuts onto each Bolt and finger tighten Figure 2 3 Turn the Anchor Jig over and place Single Straps over the Bolts Figure 3 Use the inside hole of each strap Place Hex Nuts onto each Bolt and finger tighten Figure 3 NOTE The Flat Washers Lock Washers and remaining Hex Nuts will be used to fasten the pole to the Anchor Jig 4 Before using the Anchor Jig verify that the center to center dimensions between the bolts are even Figure 4 If not adjust accordingly Firmly tighten all Hex Nuts diameter Figure 4 5 If due to conditions or other requirements leveling nuts are needed adjustments will have to be made to the Anchor Jig Below are diagrams comparing the Anchor Jig with and without leveling nuts Leveling nuts and washers are NOT provided with the pole With Leveling Nuts 2 maximum Without Leveling Nuts IMPORTANT SAFEGUARDS 1 Read Instructions All the safety and operating instructions should be read before the unit is operated 2 Retain Instructions The safety and operating instructions should be retained for future reference Heed Warnings All warnings on the unit and in the operating instructions should be adhered to 4 Follow Instructions All operating amp user instructions should be followed 5 Electrical Connections Only qualified electrician should make electrical connect
3. Registration Form at Www videolarm com productregistration jsp or complete and mail in the bottom portion of this flyer 4 Register your recent Videolarm purchases benefit from the following simple and Trouble Free RMA process Added into customer database receive product updates news Eliminate the need to archive original purchase documents LO S ae Sumneooeaue _ _ Place in envelope affix stamp and mail fo Videolarm ATTN Warranty Main Contact Info Decatur GA 30035 First Name Last Name Professional Title Company Address 1 Address 2 City State Province Country Zip Postal Code Phone Number E mail Address Product Information Please Circle One Business Personal Name amp Location of Company Store where Purchased City State Country Videolarm Product ID Product Description serial Available only for Camera Systems IR Illuminators Wireless Devices PO
4. shall pay Videolarm for the cost of investigating the problem at its then prevailing per incident billable rate No repair or replacement of any Product or part thereof shall extend the warranty period as to the entire Product The specific warranty on the repaired part only shall be in effect for a period of ninety 90 days following the repair or replacement of that part or the remaining period of the Product parts warranty whichever is greater 2 EXCLUSIVE REMEDY ACCEPTANCE Purchaser s exclusive remedy and Videolarm s sole obligation is to supply or pay for all labor necessary to repair any Product found to be defective within the warranty period and to supply at no extra charge new or rebuilt replacements for defective parts 3 EXCEPTIONS TO LIMITED WARRANTY Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the warranty period which is subjected to any of the following abuse improper use negligence accident lightning damage or other acts of God i e hurricanes earthquakes modification failure of the end user to follow the directions outlined in the product instructions failure of the end user to follow the maintenance procedures recommended by the International Security Industry Organization written in product instructions or recommended in the service manual for the Product Furthermore Videolarm shall have no liability where a schedule is specified for regular rep
5. BLE WITH ANY COMBINATION OF NON VIDEOLARM PRODUCTS OR NON VIDEOLARM RECOMMENDED PRODUCTS PURCHASER CHOOSES TO CONNECT TO PRODUCT LIMITATION OF LIABILITY THE LIABILITY OF VIDEOLARM IF ANY AND PURCHASER S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER Product Registration Warranty Thank you for choosing Videolarm We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second to none in the security industry should a problem arise rest assure that Videolarm stands behind its products 3856 by offering some of the most impressive warranty plans available 3 Years on all Housings Poles Power Supples and Accessories and 5 Years on all camera systems SView View Warriors and InfraRed Illuminators 27 A Register Your Products _ Option 1 Online option 2 Mail In Take a few moments and validate your purchase with our Online Product
6. MA CO CS REVISION DATE 02 02 2009 RE iccolarm e O q 2009 Videolarm Inc All Rights Reserved PRODUCT INSTRUCTIONS Specification Catalog 2 To help reinforce the concrete foundation place 12 1 2 diameter x 32 long Reinforcement Bars rebar as shown INSTRUCTIONS 5288 in Figure 2 Use suitable preparation methods to place the rebar MODEL Brackets Mounts and Poles P1800 STANDARD INSTALLATION PROCEDURE INCLUDES MODELS P1800 AN Please read these instructions carefully before proceeding and heed all cautions NOTE If you ll be using the optional PV4 anchor jig see the attached instructions for assembly of the jig Part 1 Site Preparation NOTE Special attention must be paid to the size of the wiring conduit and its location within the concrete foundation and jig if applicable The Wiring Conduit be up to 2 in diameter Use reducers if necessary Also make sure that the Wiring Conduit is TES T P in the center of the foundation and Anchor Jig during installation Figure 1 seen I Reinforcement bars 12 Up to 2 in Wiring conduit Figure 2 diameter Figure 1 1 Select a suitable site for the P1600 and prepare the pad site using a hole 36 x 36 x 36 deep The top of the concrete foundation should be flush with the ground CALL BEFORE DIGGING Be sure that th
7. ate connections Run video and control into the NEMA box through the conduit opening closest to the surge protector Connect video output to the surge protector Connect control wiring to the wiring panel in the top of the NEMA box Follow the wiring chart on the following page H H J AE Incoming Video 07 and Control 115 VAC Video Surge Wiring Panel rotector 115VAC to 24 VAC Video Output Protector Incoming Power NEMA Box Wiring Diagram Video output m aes ab as at D Z D D o m gt amp als N Pa 115 Incoming Power 24 VAC power User Wiring Connections pre connected RD RX Control Data ORANGE RX Control Data re TX Control Data 4 5 GREEN TX Control Data BLUE Anchor Jig Assembly Anchor Jig Kit Parts List Single Straps 4 3 4 Flat Washers 4 Cross Strap 1 10 Hex Nut 20 Lock Washers 4 1 Thread two 2 nuts onto each of the 4 bolts Figure 1 The end with 6 of clearance will be the top of the Anchor Jig the end with 1 1 2 clearance will be the bottom 1 1 2 Figure 1 NOTE Because of surface conditions it may be necessary to use leveling nuts See step 5 below for information 2 Place the short end of each Bolt into the outside holes of the
8. ere are no underground electric or phone cables gas or water lines in the area where the pole will be located 2525 Park Central Decatur Ga 30035 770 987 7550 800 554 1124 U S amp Canada www videolarm com Fax 800 826 0366 3 FOR ANCHOR BOLT INSTALLATIONS Pour concrete per manufacturer s directions making sure that the wiring conduit is in the center of the pad See Figure 3 for dimensions of the bolt pattern and suspend appropriate bolts in the concrete around the wiring conduit Leave 2 to 3 of the Bolts protruding above the pad If you are using leveling nuts leave 4 to 6 protruding 4x01 Based on an 11 B C Figure 5 2 Remove the access opening plates at the bottom and top Figure 6 3 Insert the wiring into the transformer base up into the pole and out of the bottom access opening Make sure all slack is pulled completely through 4 Insert connecting wiring into the bottom access opening run Figure 3 through the pole up to the top access opening Insert the end through the housing connecting hole Close the top access Opening and make necessary wiring connections at the bottom FOR ANCHOR JIG INSTALLATIONS access opening Figure 6 Suspend the assembled Anchor Jig in the center of the pad hole see Figure 2 previous page Leave 2 to 3 of the Bolts protruding above the pad unless you re using leveling nuts see Anchor J
9. ig instructions Make sure that the Conduit is in the center of the Anchor Jig Both the jig and the conduit must be securely suspended to prevent shifting when the concrete is poured Prepare the concrete per manufacturer s directions The concrete must have a compressive strength of 3000 psi and must be fabricated following ACI318 89 requirements Allow the concrete foundation to cure thoroughly before proceeding with the installation Access opening plates Schematic view of concrete foundation Figure 4 Part 2 Intallation 1 Assemble the pole and transformer base using the bolts nuts and washers provided Figure 5 Figure 6 5 Place the pole on the pad with the holes on the Transformer Base aligned with the bolts of the anchor bolts or anchor jig and slowly lift the pole into the upright position Figure 7 CAUTION Pull all slack in the wiring as you lift the pole into position to keep from pinching and possible damage Figure 7 5 Ensure that the pole is vertical on all sides Use a bubble level or plumb bob to check 6 Secure the pole to the pad with fasteners Figure 8 Figure 8 Wiring Inside the NEMA Box NOTE This unit MUST be grounded If you do not have ground on the incoming power you MUST run appropriate ground out from the NEMA box Run 115 VAC power into the NEMA box through the conduit opening closest to the power transformer Make the appropri
10. ions 6 Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards 7 Cable Runs All cable runs must be within permissible distance 8 Mounting This unit must be properly and securely mounted to a supporting structure capable of sustaining the weight of the unit Accordingly a Installation should be made by a qualified installer b Installation should be in compliance with local codes c Care should be exercised to select suitable hardware to install the unit taking into account both the composition of the mounting surface and the weight of the unit Be sure to periodically examine the unit and the supporting structure to make sure that the integrity of the installation is intact Failure to comply with the foregoing could result in the unit separating from the support structure and falling with resultant damages or injury fo anyone or anything struck by the falling unit UNPACKING Unpack carefully Electronic components can be damaged if improperly handled or dropped If an item appears to have been damaged in shipment replace it properly in its carton and notify the shipper Be sure fo save 1 The shipping carton and packaging material They are the safest material in which to make future shipments of the equipment 2 These Installation and Operating Instructions LIMITED WARRANTY viDEOLARM INC PRODUCTS SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK
11. lacement or maintenance or cleaning of certain parts based on usage and the end user has failed to follow such schedule attempted repair by non qualified personnel operation of the Product outside of the published environmental and electrical parameters or if such Product s original identification trademark serial number markings have been defaced altered or removed Videolarm excludes from warranty coverage Products sold AS IS and or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser All software and accompanying documentation furnished with or as part of the Product is furnished AS IS 1 without any warranty of any kind except where expressly provided otherwise in any documentation or license agreement furnished with the Product 4 PROOF OF PURCHASE The Purchaser s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY AND OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2 312 3 OF THE UNIFORM COMMERCIAL CODE AND OR IN ANY OTHER COMPARABLE STATE STATUTE VIDEOLARM HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATI
12. trollers Five 9 Years tour operation Five 5 tour operation Power Supplies Accessory Brackets Five 5 Years Five 5 Years Five 5 Years Five 5 Years During the labor warranty period to repair the Product Purchaser will either return the defective product freight prepaid or deliver it to Videolarm Inc Decatur GA The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a RMA Return Materials Authorization number displayed on the outer box or packing slip To obtain a RMA you must contact our Technical Support Team at 800 554 1124 extension 101 Videolarm will return the repaired Product freight prepaid to Purchaser Videolarm is not obligated to provide Purchaser with a substitute unit during the warranty period or at any time After the applicable warranty period Purchaser must pay all labor and or parts charges The limited warranty stated in these product instructions is subject to all of the following terms and conditions 1 NOTIFICATION OF CLAIMS WARRANTY SERVICE If Purchaser believes that the Product is defective in material or workmanship then written notice with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the warranty period If after investigation Videolarm determines that the reported problem was not covered by the warranty Purchaser
Download Pdf Manuals
Related Search