Keysight 16047A Test Fixture
Contents
1. December 1999 Third Edition part number 16047 90011 November 2014 Fourth Edition part number 16047 90011 Safety Summary The following general safety precautions must be observed during all phases of operation service and repair of this instrument Failure to comply with these precautions or with specific WARNINGS elsewhere in this manual may impair the protection provided by the equipment In addition it violates safety standards of design manufacture and intended use of the instrument The Keysight Technologies assumes no liability for the customer s failure to comply with these requirements 16047A comply with INSTALLATION CATEGORY I and POLLUTION DEGREE 2 in IEC61010 1 16047A are INDOOR USE product WARNING Ground The Instrument To avoid electric shock hazard the instrument chassis and cabinet must be connected to a safety earth ground by the supplied power cable with earth blade DO NOT Operate In An Explosive Atmosphere Do not operate the instrument in the presence of flammable gasses or fumes Operation of any electrical instrument in such an environment constitutes a definite safety hazard Keep Away From Live Circuits Operating personnel must not remove instrument covers Component replacement and internal adjustments must be made by qualified maintenance personnel Do not replace components with the power cable connected Under certain conditions dangerous voltages may exist even with the power ca2. 0515 1550 0515 0914 16047 04011 0515 0914 16047 00618 16061 50024 0515 1467 16061 50031 16061 10031 1460 0343 16061 10026 16061 10033 16061 10032 16061 50032 16047 00604 16047 00605 16047 40001 16061 70021 16061 70022 16047 65001 5000 4226 N N N N N N N N N A d A N N N Description COVER BOTTOM NUT WASHER SCREW BASE CONNECTOR BNC CONNECTOR BNC STOPPER WASHER SCREW SCREW COVER TOP SCREW SHIELD PLATE SOCKET SCREW SOCKET RADIAL CONTACT RADIAL SPRING CONTACT CONTACT AXIAL CONTACT AXIAL SOCKET AXIAL CONTACT CONTACT SOCKET SOCKET ASSEMBLY 23 and 24 SOCKET ASSEMBLY 28 29 and 30 SOCKET ASSEMBLY 31 32 and 33 Short Bar Chapter2 This information is subject to change without notice Keysight Technologies 1985 1998 1999 2014 Edition 4 November 2014 KEYSIGHT WU TECHNOLOGIES 16047 90011 www keysight com
3. 10032 CONTACT AXIAL 16061 50032 SOCKET AXIAL 16047 00604 CONTACT 16047 00605 CONTACT 16047 40001 SOCKET 16061 70021 Po Po Po PM PP P PP PO Bi BIBI pl Po po pe rm oa o ol ml mola pmol ap BR a SOCKET ASSEMBLY 23 and 24 36 16061 70022 SOCKET ASSEMBLY 28 29 and 30 37 16047 65001 SOCKET ASSEMBLY 31 32 and 33 1 This short bar is not included in 16047A It is prepared as option of 16047A Option number is 16047A 701 38 5000 4226 Copyright 2008 2014 Keysight Technologies N 1 Short Bar NOTE Notices The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of the Keysight Technologies Copyright 1985 1998 1999 2014 Keysight Technologies Manual Printing History The manual s printing date and part number indicate its current edition The printing date changes when a new edition is printed Minor corrections and updates that are incorporated at reprint do not cause the date to change The manual part number changes when extensive technical changes are incorporated April 1985 First Edition part number 16047 90000 December 1998 Second Edition part number 16047 90011
4. Keysight 16047A Test Fixture Operation and KEYSIGHT Service Manual TECHNOLOGIES NOTICE This document contains references to Agilent Technologies Agilent s former Test and Measurement business has become Keysight Technologies For more information go to www keysight com KEYSIGHT TECHNOLOGIES Keysight 16047A TEST FIXTURE Operation and Service Manual Manual Change Keysight Part No N A November 2014 Change 1 Add the note under Figure 1 3 on page 13 NOTE This short bar is not included in 16047A It is prepared as option of 16047A Option number is 16047 A 701 Copyright 2008 2014 Keysight Technologies Change 2 Change the part number in Table 2 1 in Page 18 and add footnote to Item 38 Reference Designator Table 2 1 Replaceable Parts List Keysight Part Number 16047 04013 Quantity Description COVER BOTTOM 2950 0043 NUT 2190 0016 WASHER 0515 1467 SCREW 16061 50022 BASE 16047 60016 CONNECTOR BNC 16012 7122 CONNECTOR BNC 16047 40000 STOPPER 2190 0206 WASHER 0515 1550 SCREW 0515 0914 SCREW 16047 0401 1 COVER TOP 0515 0914 SCREW 16047 00618 SHIELD PLATE 16061 50024 SOCKET 0515 1467 SCREW 16061 50031 SOCKET RADIAL 16061 10031 CONTACT RADIAL 1460 0343 SPRING 16061 10026 CONTACT 16061 10033 CONTACT AXIAL 16061
5. ble removed To avoid injuries always disconnect power and discharge circuits before touching them DONOT Service Or Adjust Alone Do not attempt internal service or adjustment unless another person capable of rendering first aid and resuscitation is present DONOT Substitute Parts Or Modify Instrument Because of the danger of introducing additional hazards do not install substitute parts or perform unauthorized modifications to the instrument Return the instrument to a Keysight Technologies Sales and Service Office for service and repair to ensure that safety features are maintained Dangerous Procedure Warnings Warnings such as the example below precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed Dangerous voltages capable of causing death are presenting this instrument Use extreme caution when handling testing and adjusting this instrument Certification Keysight Technologies certifies that this product met its published specifications at the time of shipment from the factory Keysight Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology to the extent allowed by the Institution s calibration facility or to the calibration facilities of other International Standards Organization members IMPORTANT Warranty This Keysight Technologies instrument p
6. ent s Open Short compensation procedure should be performed The procedure is given in the instrument s operating manual For SHORT compensation a low impedance copper or phosphor bronze shorting bar such as the one shown in Figure 1 3 is recommended Figure 1 3 Shorting bar dimensions 15 15 Indicated values are in mm Thickness is 0 4mm Chapter 1 13 Operation Introduction 14 Chapter 1 Service Service Maintenance Maintenance The internal wiring of the 16047A is shown in Figure 2 1 and an exploded View for parts identification in Table 2 2 Do not disassemble any further than shown Maintenance consists principally of cleaning contacts and replacing worn or damaged parts Take special care when cleaning contacts To order parts use the Keysight Technologies part numbers listed in Table 2 1 Ifa faulty part is located in an assembly that cannot be disassembled order the next higher assembly or return the whole device to the nearest Keysight Technologies Sales Service Office for repair or replacement Figure 2 1 Internal Wiring of 16047A 16 Chapter2 Figure 2 2 Parts Identification 16047 65001 16061 70022 16061 70021 Chapter 2 Service Maintenance Service Maintenance Table 2 1 Reference 18 Replaceable Parts List Keysight Part No 16047 04013 2950 0043 2190 0016 0515 1467 16061 50022 1250 1798 16012 7122 16047 40000 2190 0206
7. h is essential to highlight Contents 1 Operation Introduction 10 Product Description 10 Specifications 11 Typical Characteristics 12 Compensation for Fixture Residual Impedance Error 13 2 Service Maintenance 16 Contents Operation Figure 1 1 Table 1 1 Operation Introduction Introduction This chapter provides complete information of the 16047A Test Fixture Product Description The 16047A Test Fixture is designed for use with 4 terminal pair LCR Meters and Impedance Analyzers It is a direct attachment 4 terminal pair configuration type test fixture for measurements on both axial and radial lead components Three contact inserts labelled 1 2 and 3 in Figure 1 1 are available 1 for measurements on axial components and 2 and 3 for measurements on radial lead components These parts number is listed in Table 1 1 The dimensions of the contact inserts are given in Table 1 2 16047A Test Fixture Parts number Keysight Part No 1 16061 70022 2 16047 65001 3 16061 70021 10 Chapter 1 Specifications Operation Introduction Specification of the 16047A Function For use with 4 terminal pair LCR Meters and Impedance Analyzers Measurable Axial and radial lead components components Contact inserts Three kinds one for axial lead components one for radial lead components and one for radial short lead components Dimensions
8. of Test Fixture Contacts Frequency lt 13 MHz Maximum Voltage 40V peak max AC DC Dimensions of test fixture 124 W x 31 D x 62 H mm Weight 205 g Safety Standards EN61010 1 1993 A2 1995 IEC61010 1 1990 A1 1992 A2 1995 CSA C22 2 No 1010 1 1992 INSTALLATION CATEGORY I POLLUTION DEGREE 2 INDOOR USE Chapter 1 11 Table 1 3 NOTE Figure 1 2 Operation Introduction Typical Characteristics Typical characteristics Incremental Error at f 21 MHz Parameter reading error Offset Value for D 15x so 02x L 10 2 10 fis the measurement frequency in MHz The incremental errors calculated from the equation in the table for measurements at frequencies above MHz are additive Incremental error at frequency above 1 MHz Error Offset value in D 4 6 8 10 13 Frequency MHz Parameter reading error vs frequency 12 jk Frequency MHz Offset value in D vs frequency Chapter 1 Operation Introduction Compensation for Fixture Residual Impedance Error The 16047A has inherent stray capacitance residual inductance and residual resistance that affect the accuracy of measured values To compensate for or negate these residuals to minimize measurement error the instrum
9. ogies specifically disclaims the implied warranties of merchantability and fitness for a particular purpose Exclusive Remedies The remedies provided herein are buyer s sole and exclusive remedies Keysight Technologies shall not be liable for any direct indirect special incidental or consequential damages whether based on contract tort or any other legal theory WARNING CAUTION NOTE Assistance Product maintenance agreements and other customer assistance agreements are available for Keysight Technologies products For any assistance contact your nearest Keysight Technologies Sales and Service Office Addresses are provided at the back of this manual Safety Symbol General definitions of safety symbols used on the instrument or in manuals are listed below Instruction Manual symbol the product is marked with this symbol when it is necessary for the user to refer to the instrument manual This warning sign denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result in injury or death to personnel This Caution sign denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result in damage to or destruction of part or all of the product Note denotes important information It calls attention to a procedure practice condition or the like whic
10. roduct is warranted against defects in material and workmanship for a period corresponding to the individual warranty periods of its component products Instruments are warranted for a period of one year During the warranty period Keysight Technologies will at its option either repair or replace products that prove to be defective For warranty service or repair this product must be returned to a service facility designated by Keysight Technologies Buyer shall prepay shipping charges to Keysight Technologies and Keysight Technologies shall pay shipping charges to return the product to Buyer However Buyer shall pay all shipping charges duties and taxes for products returned to Keysight Technologies from another country Keysight Technologies warrants that its software and firmware designated by Keysight Technologies for use with an instrument will execute its programming instruction when property installed on that instrument Keysight Technologies does not warrant that the operation of the instrument or software or firmware will be uninterrupted or error free Limitation Of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by Buyer Buyer supplied software or interfacing unauthorized modification or misuse operation outside the environmental specifications for the product or improper site preparation or maintenance No other warranty is expressed or implied Keysight Technol
Download Pdf Manuals
Related Search