RANGE - HellermannTyton
Contents
1. Number of cylinders defaults at 4 cylinders Press CYLINDER button for one second or more to RPMS for 2 stroke and stroke button momentarily to select through RPM 4 for 4 M for special 2 stroke waste ignition engine 2 DIS and RPM Press IGNITION COIL TO DISTRIBUTOR RED CHASSIS GROUND BLACK a a A M function RM4 2 or 2 IG will be saved as power up default for repeat measurement convenience Press the SELECT button momentarily to select the subject functions in sequence Last selection amp ms functions DWELL ZY DUTY RPM IG 33 EJ CYLINDER TRIGGER Loval GS Cem 02 0 UU rf 7 display the cylinder setting and press momentarily again within one second to select the number of cylinders from 1 through 12 to match the engine under test Trigger level defaults at 3 Press the Level RANGE button momentarily to select another trigger level If the RPM reading becomes unstable select lower sensitivity to avoid electrical noise If the reading shows zero select higher sensitivity Number of Bar graph pointer is us2. SIGNAL JUMPER ON TIME THROTTLE BODY INJECTION WAVEFORM Heal PORT FUEL INJECTION PFI OR TBI INJECTOR WAVEFORM 12V SUPPLY OR B Trigger level defaults at 3 Press the Level RANGE button momentarily to select another trigger level If the reading becomes unstable select lower sensitivity to avoid electrical noise If the reading shows zero select higher sensitivity Number of Bar graph pointer is used to indicate sensitivity selected Positive amp negative trigger slopes are selectable through pressing Z TRIGGER button for one second or more Press SELECT button momentarily 3 times to display ms reading in terms of percentage if required Note This ms function applies to both Port Fuel Injectors PFI which operate with a single on time pulse and Throttle Body Injectors TBI which operate with twin pulses 4 Z or M function INDUCTIVE PICK UP BP300 Press button momentarily to select through RPM 41 for 4 stroke RPM for 2 stroke and DIS and RPM M for special 2 stroke waste ignition engine Trigger level defaults at 3 Press the Level RANGE button momentarily to select another trigger level If the RPM reading becomes unstable select lower sensitivity to avoid electrical noise If the reading shows zero select higher sensiti
3. C lt 80 R H with battery removed Temperature Coefficient Nominal 0 15 x specified accuracy C 0 C 18 C or 28 C 40 C or otherwise specified Sensing Average sensing Pollution Degree 2 12 Safety Double insulation per IEC61010 1 2nd Ed EN61010 1 2nd Ed UL61010 1 2nd Ed amp CAN CSA C22 2 No 61010 1 0 92 to Category Il 1000V AC amp DC Transient Protection 6kV 1 2 50us surge Terminals to COM Measurement Category V Category II 1000V AC amp DC A amp mAuA Category Il 450V AC amp DC E M C Meets EN61326 1 2006 EN55022 EN61000 3 2 EN61000 3 3 EN61000 4 2 EN61000 4 3 EN61000 4 4 EN61000 4 5 EN61000 4 6 EN61000 4 8 EN61000 4 11 In an RF field of 3V m Capacitance function is not specified Other function ranges Total Accuracy Specified Accuracy 100 digits Performance above 3V m is not specified Overload Protection uA amp mA 0 63A IR 50kA 500Vac A 6 3A IR 50kA 2500Vac 6 V 1050 Vrms 1450 Vpeak mV Ohm amp others 600 Vrms Low Battery Below approx 2 3V Power Supply 1 5V AAA Size battery X 2 Power Consumption typical 4 3mA APO Consumption typical APO Timing Idle for 34 minutes Dimension 161 80 50mm L W H With Holster Weight Approx 340 gm With Holster Special Features Backlighted LCD Model 319 only Trigger Selectable positive amp negative trigger slopes Cylinder 9 Selectable number of cylinders 1 2 3 4 5 6 8 10 amp 12 in Dwell
4. and IG RPM functions Hold Freezes the display data for later view Range Manual amp Auto ranging selection RPM 4 For RPM of traditional 4 stroke engines which have 1 ignition on every 4 engine strokes RPM 2 For RPM of DIS amp traditional 2 stroke engines which have 1 ignition on every 2 engine strokes RPM 2 M For RPM of 2 stroke waste ignition on board engines which have 1 ignition on every single engine stroke Accessories Test lead pair batteries installed user s manual BKP60 banana plug type K thermocouple Model 319 only BP300 Inductive pickup clip Model 319 only Optional purchase accessories Magnetic hanger BMH 01 BKB32 banana plug to type K socket plug adaptor Model 319 only BP300 Inductive pickup clip Model 315 only Electrical Specification Accuracy is given as of reading digits number of digits or otherwise specified 23 C 5 C and less than 75 R H DC Voltage RANGE Accuracy Capacitance Model 319 only 60 00mV 0 495 43d RANGE Accuracy 600 0mV 0 3 3d 2 0 5d 0 4 3d 60 00 600 0uF 3 5 5d 1000V 0 7 3d Input Impedance 10MQ 50 pF nominal Accuracies with film capacitor or better AC Voltage DC Current RANGE Accuracy 600 00A9 0 7 3d 2 0 5d 0 5 3d 6 000V 60 00V 600 0V 60 00mA 0 Input Impedance 10MQ 50 pF nominal 6 000A 0 795 3d Ohm Ranges for Model 319 only RANGE Accuracy 264 continuous gt 6A to 10A for 30 sec max RANGE
5. shows zero select higher sensitivity Number of Bar graph pointer is used to indicate input range sensitivity selected 1 2 3 4 pointers indicate that 6 60 600 1000V is selected respectively Q Resistance Continuity Capacitance Model 319 only amp gt Diode test functions Press the SELECT button momentarily to select the subject functions in sequence Last selection will be saved as power up default for repeat measurement convenience FORWARD BIAS REVERSE BIAS CAUTION Discharge capacitors before making any measurement Large value capacitors should be discharged through an appropriate resistance load CAUTION Using resistance and continuity function in a live circuit will produce false results and may damage the instrument In many cases the suspected component must be disconnected from the circuit to obtain an accurate reading I Continuity function is convenient for checking wiring connections and operation of switches A continuous beep tone indicates a complete wire Normal forward voltage drop forward biased for a good silicon diode is between 0 400V to 0 900V A reading higher than that indicates a leaky diode defective A zero reading indicates a 5 shorted diode defective An OL indicates an open diode defective Reverse the test leads connections reverse biased across the diode The digital display
6. shows OL if the diode is good Any other readings indicate the diode is resistive or shorted defective DCmV ACmV amp Temperature C amp F functions Model 319 only Press the SELECT button momentarily to select the subject functions in sequence Last selection will be saved as power up default for repeat measurement convenience fols CUDL EJ CYLINDER TRIGGER Level gt E A 9171 Td Note Be sure to insert the banana plug K type temperature bead probe Bkp60 with correct F polarities You can also use a plug adapter Bkb32 Optional purchase with banana pins to K type socket to adapt other standard K type mini plug temperature probes uA Model 319 only mA Model 319 only and A Current functions Press SELECT button momentarily to toggle between DC and AC Last selection will be saved as power up default for repeat measurement convenience Note When measuring a 3 phase system special attention should be taken to the phase to phase voltage which is significantly higher than the phase to earth voltage To avoid exceeding the voltage rating of the protection fuse s accidentally always consider the phase to phase voltage as the working voltage for the protection fuse s
7. AC signal The average value is then scaled upward calibrated to read the RMS value of a sine wave In measuring pure sinusoidal waveform this technique is fast accurate and cost effective In measuring non sinusoidal waveforms however significant errors can be introduced because of different scaling factors relating average to RMS values 4 OPERATION CAUTION Before and after hazardous voltage measurements test the voltage function on a known source such as line voltage to determine proper meter functioning DCV ACV amp Line Frequency functions Press the SELECT button momentarily to select the subject functions in sequence Last selection will be saved as power up default for repeat measurement convenience Note Input sensitivity varies automatically with function range selected before activating the Hz 4 function 6V function range has the highest and the 1000 range has the lowest It is recommended to first measure the signal voltage or current level then activate the Hz function in that voltage or current range to automatically set the most appropriate trigger level You can also press the Level RANGE button momentarily to select another trigger level manually If the Hz reading becomes unstable select lower sensitivity to avoid electrical noise If the reading
8. Accuracy Burden Voltage 600 00 0 596 6d with 5 minutes cool down interval 6 000KO 60 00KQ 0 5 3d 600 0KQ 0 8 4d AC Current RANGE Accuracy Burden Voltage 600 0uA 2 2 5d 6000uA 2 0 6d Audible Continuity Tester 60 00mA 2 2 5d 25 mVimA Audible Threshold Between 10 and 200 600 0mA 2 0 5d l Response time 32ms 6 000A 2 2 5d 10 00A 2 1 2 5d ee Diode Tester Ranges for Model 319 only RANGE Accuracy 2 6A continuous gt 6A to 10A for 30 sec max 1 000V 1 0 3d with 5 minutes cool down interval Test Current 0 50mA typically Open Circuit Voltage lt 1 6VDC typically 6 000MQ 1 0 5d 60 00MQ 1 5 5d Open Circuit Voltage 0 45VDC typical Temperature Model 319 only DWELL RANGE Accuracy RANGE Accuracy 58 oF 1832 F K type thermocouple range amp accuracy not Specified ranges depend on engine rpm and included number of Cylinders cyl Nine selectable Cylinders 1 2 3 4 5 6 8 IP RPM Inductive pickup type 10 amp 12 RANGE Accuracy Four selectable trigger levels 240 20000 RPM 2RPM Sensitivity 120 10000 RPM 2 RPM E nod typically evel 2 1 85V typically pickup Level 3 3 75V typically Level 4 6V typicall optional purchase for Model 315 EXE ypically Four selectable trigger levels Sensitivity Fuel injection ms detector Level 1 3 0V typically Accuracy Level 2 4 5V ty
9. C DIRECTIVES The instruments conform to CENELEC Low voltage directive 2006 95 EC and Electromagnetic 1 3 5 6 digits 6000 counts LCD display 2 Push buttons for special functions amp features 3 Selector to turn the Power On or Off and Select a function 4 Input Jack for milli amp and micro amp current functions 5 Input Jack for all functions EXCEPT current uA mA A functions 6 Common Ground reference Input Jack for all functions T Input Jack for 6A 15A for 30sec current function compatibility directive 2004 108 EC 3 PRODUCT DESCRIPTION Note Top of the line model is used as representative for illustration purposes Please refer to your respective model for function availability 0 0 per 13 1 JF IP RPM 2 Temp 242 3 Analog bar graph The analog bar graph provides a visual indication of measurement like a traditional analog meter needle It is excellent in detecting faulty contacts identifying potentiometer clicks and indicating signal spikes during adjustments Average sensing RMS calibrated RMS Root Mean Square is the term used to describe the effective or equivalent DC value of an AC signal Most digital multimeters use average sensing RMS calibrated technique to measure RMS values of AC signals This technique is to obtain the average value by rectifying and filtering the
10. PO press the SELECT button momentarily or turn the rotary switch OFF and then back on Always turn the rotary switch to the OFF position when the meter is not in use Disabling Auto Power Off Press the SELECT button while turning the meter on to temporarily disable the Auto Power Off APO feature Turn the rotary switch OFF and then back on to resume 5 MAINTENANCE WARNING To avoid electrical shock disconnect the meter from any circuit remove the test leads from the input jacks and turn OFF the meter before opening the case Do not operate with open case Install only the same type of fuse or equivalent Calibration Periodic calibration at intervals of one year is recommended to maintain meter accuracy Accuracy is specified for a period of one year after calibration If self diagnostic message C_Er is being displayed while powering on some meter ranges might be largely out of specifications To avoid mis leading measurements stop using the meter and send it for re calibration Refer to the LIMITED WARRANTY section for obtaining warranty or repairing service Cleaning and Storage Periodically wipe the case with a damp cloth and mild detergent do not use abrasives or solvents If the meter is not to be used for periods of longer than 60 days remove the battery and store it separately Trouble Shooting If the instrument fails to operate check battery fuses leads etc and replace as necessary Double check operating procedure
11. USER S MANUAL AE TBM315 T TBM319 Automotive Multimeter IOP TRONIC HellermannTyton C MAX 0 6A MAX 6 BRYMEN HBC FUSED HEG FUSED aby BRIGHT PEOPLE S CHOICE 1 SAFETY Terms in this manual WARNING _ identifies conditions and actions that could result in serious injury or even death to the user CAUTION identifies conditions and actions that could cause damage or malfunction in the instrument This manual contains information and warnings that must be followed for operating the instrument safely and maintaining the instrument in a safe operating condition If the instrument is used in a manner not specified by the manufacturer the protection provided by the instrument may be impaired The meter is intended only for indoor use The meter protection rating against the users is double insulation per IEC61010 1 2nd Ed EN61010 1 2nd Ed UL61010 1 2nd Ed and CAN CSA C22 2 No 61010 1 0 92 to Category Il 1000V AC amp DC Terminals to COM measurement category V Category II 1000V AC amp DC A 8 mApuA Category Il 450V AC amp DC Per IEC61010 1 2nd Ed 2001 Measurement Category Measurement Category Il CAT Il is for measurements performed on circuits directly connected to the low voltage installation Examples are measurements on household appliances portable tools and similar equipment WARNING To reduce the risk of fire or electric shock do not expose this product to rain or mois
12. as described in this user s manual 1 If the instrument voltage resistance input terminal has subjected to high voltage transient caused by lightning or switching surge to the system by accident or abnormal conditions of operation the series fusible resistors will be blown off become high impedance like fuses to protect the user and the instrument Most measuring functions through this terminal will then be open circuit The series fusible resistors and the spark gaps should then be replaced by qualified technician Refer to the LIMITED WARRANTY section for obtaining warranty or repairing service Battery and Fuse replacement Battery use 1 5V AAA Size battery x 2 Fuses use Fuse F2 for wAmA current input 0 63A IR 50kA 2500Vac amp 1 5kA 450Vdc F fuse or better Dimension 6 x 32 mm Fuse F1 for A current input 6 3A IR 50kA 500Vac amp 1 5kA 450Vde F fuse or better Dimension 6 x 32 mm Battery and Fuse replacement Loosen the screw from the access cover of the case bottom Lift the access cover Replace the batteries or fuse Re fasten the screw GENERAL SPECIFICATION Display 3 5 6 digits 6 000 counts Update Rate 5 per second nominal 24 Segments Bar graph 40 per second max Operating Temperature 0 C to 40 C Relative Humidity Maximum relative humidity 80 for temperature up to 31 C decreasing linearly to 50 relative humidity at 40 C Altitude Operating below 2000m Storage Temperature 20 C 60
13. ed to indicate sensitivity selected ZY DWELL 8 Duty functions 1 11 7 E3 CYLINDER TRIGGER Level E a BLACK a RED CO CHASSIS GROUND TO DISTRIBUTOR IGNITION COIL Number of cylinders defaults at 4 cylinders Press Cylinder button for one second or more to display the cylinder setting and press momentarily again within one second to select the number of cylinders from 1 through 12 to match the engine under test Adjust the dwell angle according to the procedures outlined in your vehicle service manual Re check the timing whenever the dwell angle has been adjusted Press SELECT button momentarily to display DWELL reading in terms of percentage 96 if required Positive amp negative trigger slopes are selectable through pressing TRIGGER button for one second or more in Duty function for advanced applications Trigger level defaults at 3 Press the Level RANGE button momentarily to select another trigger level If the ZY DWELL or Duty reading becomes unstable select lower sensitivity to avoid electrical noise If the reading shows zero select higher sensitivity Number of Bar graph pointer is used to indicate sensitivity selected ms FUEL INJECTION DETECTOR function
14. pically PFI Multi Point Injection Level 3 6 1V typically 05ms 250 0ms 0 05ms 1d Level 4 8 1V typically 0 100 0 0 04 krpm 2d TBI Single Point Injection IG RPM Contact signal type 0 05ms 1d RANGE Accuracy 0 0 100 0 0 04 krom cyl 0 60 20000 RPM 2 RPM Specified range depends on engine rpm 30 10000 RPM 2 RPM Selectable trigger slopes 15 5000 RPM 2 RPM Four selectable trigger levels Measurements via test leads on Dwell Fuel Sensitivity injection ms and ignition primary signals Level 1 0 8V typically Nine selectable Cylinders 1 2 3 4 5 6 8 10 Level 2 1 85V typically amp 12 Level 3 3 75V typically Four selectable trigger levels Level 4 6V typically Sensitivity Level 1 0 8V typically Hz Line level ACV amp DCV Level 3 3 75V typically Sine RMS 9 Level 4 6V typically Accuracy 0 1 3d LIMITED WARRANTY BRYMEN warrants to the original product purchaser that each product it manufactures will be free from defects in material and workmanship under normal use and service within a period of one year from the date of purchase BRYMEN s warranty does not apply to accessories fuses fusible resistors spark gaps batteries or any product which in BRYMEN s opinion has been misused altered neglected or damaged by accident or abnormal conditions of operation or handling To obtain warranty service contact your nearest BRYMEN authorized agent or send the product
15. ture To avoid electrical shock hazard observe the proper safety precautions when working with voltages above 60 VDC or 30 VAC rms These voltage levels pose a potential shock hazard to the user Do not touch test lead tips or the circuit being tested while power is applied to the circuit being measured Keep your fingers behind the finger guards of the test leads during measurement Inspect test leads connectors and probes for damaged insulation or exposed metal before using the instrument If any defects are found replace them immediately Do not measure any current that exceeds the current rating of the protection fuse Do not attempt a current measurement to any circuit where the open circuit voltage is above the protection fuse voltage rating Suspected open circuit voltage should be checked with voltage functions Never attempt a voltage measurement with the test lead inserted into the uA mA or A input jack Only replace the blown fuse with the proper rating as specified in this manual CAUTION Disconnect the test leads from the test points before changing functions Always set the instrument to the highest range and work downward for an unknown value when using manual ranging mode Caution Refer to the explanation in this Manual Double Insulation or Reinforced insulation INTERNATIONAL ELECTRICAL SYMBOLS Caution Risk of electric shock Earth Ground Fuse AC Alternating Current DC Direct Current d otee 2 CENELE
16. vity Number of Bar graph pointer is used to indicate sensitivity selected Backlighted LCD display Model 319 only Press the SELECT button for 1 second or more to toggle the LCD backlight The backlight will also be turned off automatically after 32 seconds to extend battery life Hold The hold feature freezes the display for later view Press the HOLD button momentarily to toggle the hold feature Manual or Auto ranging Press the RANGE button momentarily to select manual ranging and the meter will remain in the range it was in the LCD turns off Press the button momentarily again to step through the ranges Press and hold the button for 1 second or more to resume auto ranging 10 Note Manual ranging feature is not available in Hz MF RPM ms DWELL amp Duty functions Set Beeper Off Press the RANGE button while turning the meter on to temporarily disable the Beeper feature Turn the rotary switch OFF and then back on to resume Beep Jack Input Warning The meter beeps as well as displays InEr to warn the user against possible damage to the meter due to improper connections to the uA mA or A input jacks when other function like voltage function is selected Auto Power Off APO The Auto Power Off APO mode turns the meter off automatically to extend battery life after approximately 34 minutes of no rotary switch or push button operations To wake up the meter from A
17. with proof of purchase and description of the difficulty postage and insurance prepaid to BRYMEN TECHNOLOGY CORPORATION BRYMEN assumes no risk for damage in transit BRYMEN will at its option repair or replace the defective product free of charge However if BRYMEN determines that the failure was caused by misused altered neglected or damaged by accident or abnormal conditions of operation or handling you will be billed for the repair THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE BRYMEN WILL NOT BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES BRYMEN BRIGHT PEOPLE S CHOICE BRYMEN TECHNOLOGY CORPORATION TEL 886 2 2226 3396 FAX 886 2 2225 0025 http www brymen com X 9 PRINTED ON RECYCLABLE PAPER PLEASE RECYCLE COPYRIGHT MMXI BTC ALL RIGHTS RESERVED P N 7M1C 1211 0003 PRINTED IN TAIWAN
Download Pdf Manuals
Related Search