W360 Multifunction Tabber System
Contents
1. pt e 4 1 MA 1 or py p 3 Loosen the nut on the idler pulley and adjust the tension 1 8 play in the motor drive belt PC TRIN 4 Tighten the nut and then recheck the adjustment 5 Replace the covers 19 SV62477 Rev W360 Tabber Service Manual ADJUSTMENTS Tab Guide Plate Alignment Requirement The Tab Guide Plate must be returned to its proper position whenever it is removed for cleaning Adjustment 1 The Tab Guide Plate is held in place by two screws and a nut plate 2 Loosen the two Guide Plate mounting screws and install the 41 109 30 Tab Plate Installation Fixture over the Tab Guide making sure that the lip on the fixture 1s between the belt and the Guide Plate 3 Push the Tab Guide Plate against the fixture and toward the Guide and the Transport Belt 4 Tighten the two screws and then remove the fixture 5 When the adjustment is complete the Tab Guide Plate should be 0 040 from the Side of the Guide and 0 020 from the belt NOTE The 41 109 30 Fixture is used for both heads 20 5 62477 Rev W360 Tabber Service Manual ADJUSTMENT Tab Brake Adjustment Head 1 and Head 2 Requirement The Tab Brake must be set properly to advance the tabs Adjustment 1 Q A W N Remove the Rear Cover of the Tabber to access Brake on Head 2 remove the Top cover from the Head 1 to access its Brake Loosen the two Allen screws2. XX I BOARD MEDIA l PROCESSOR BOARD IE TAREN MEL RI ee JB COMMUNICATIONS Tene e gg alee mas veneer mer a cr D MMC TAB SENSOR I rH mue Ih A CABLE V A 55 SV62477 Rev W360 Tabber Service Manual APPENDIX FF 309 Feeder Wiring Diagram b 4 SW 1 FUSE 2A Lil U31 SPEED CONTROL 53 p oo U23 POTENTIOMETER p RECEPTACLE AUTO MANUAL SWITCH 56 SV62477 Rev A W360 Tabber Service Manual INDEX A Adjustments Advanced Assembly Assembly Installation and Operation C Cleaning Cleaning the Sensors Cleaning the Tab Wrap Guides Connecting D Diagnostics Disassembly and Assembly E Encoder and Encoder Driver Belt Exit End View F Feeder and Connections Feeder Front View Feeder Wiring Diagram Front View H Head Assembly Alignment I Identifying Tab Types J Jams L Left Hand Side Cover Lubrication M Maintenance Media Sensor Adjustment Media Sensor Test 57 19 15 49 50 51 16 31 35 4 58 23 54 11 35 52 49 27 51 INDEX 5 62477 Rev INDEX W360 Tabber Service Manual Motor Drive Belt P Power Supply Adjustment R Removing Covers Removing Front Cover Removing Rear Cover Removing Reel Assembly Removing the Drive Roller Replacing Clutch and B
3. The following images will help you identify which Tab Type Opaque or Clear to select when using the Automatic V Tab feature Tab Type Opaque Stock that has white space line white gap between each tap stamp Tab Material Clear or Translucent Backing Black Box under the tab area Gap White Tab Material White Paper Circle Backing White Gap White Tab Material Stamp Backing White Gap White Tab Material Colored Backing White Gap White Tab Type Clear Stock that has a black space line black Gap between each tab Tab Material Translucent Circle Backing Black line between each tab Gap Black Tab Material Clear Circle Backing Black line between each tab Gap Black 54 5 62477 Rev W360 Tabber Service Manual APPENDIX Appendix C Wiring Diagrams Tabber Wiring Diagram PME LCD unm ET u L 1 s POWER 115VAC i FUSE 2 5 A SLO BLO 8 TB1 3 T E 115 in gt ui 1 POWER 9 SUPPLY x T 83 B B INTERFACE FEEDER 1 3 SAFETY fal 345 NO cover eg SWITCH 7 INTERFACE a n cC NNNM lj few TABBER TO TURN OFF as INTERFACE OTHER EQUIPMENT EJ JUMPER qM MEE m l SAFETY COVER Fi EMERGENCY STOP TABBER KEYBOARD WITH DISPLAY
4. PitnevBowes W360 Multifunction Tabber System E 2 SS CAE lt Uu X EOS E l y l as 1 Service Manual NOTICE The use of this information by the recipient or others for purposes other than the repair adjustment or operation of Pitney Bowes equipment may constitute an infringement of patent and or other intellectual property rights of Pitney Bowes or others Pitney Bowes assumes no responsibility for any such use of the information Except as provided in writing duly signed by an officer of Pitney Bowes no license either express or implied under any Pitney Bowes or any third party s patent copyright or other intellectual property rights is granted by providing this information Declaration of Conformity According to FCC Rules Part 2 Paragraph 2 1077 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this de vice may not cause harmful interference and 2 this device must accept any interference received including interfer ence that may cause undesired operation Responsible party Pitney Bowes 1 Elmcroft Rd Stamford CT 06926 0700 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment This equipment generates u
5. 0 FI MES gies Z SH ove J eek WN 4 Bu 4 7 E U Em 1 1 j hi 1 z d 7 iF eg d 3 i E TN E E m Bi im 7 E CM ac ie i Ls Eu 1 r js hr a 19 427 YI NI 3 5 2 9 He mue x TT EAE e s 5g m p E nnn mn rau abun FYE rai RAS ET ia cs I O PC BOARD 2 5 62477 Rev A W360 Tabber Service Manual ADJUSTMENTS Media Sensor Adjustment Requirement Adjust the Media Sensors so that they detect the media Adjustment 1 Turn the tabber on with the main power switch 2 Placea piece of white paper or card stock on the belts so that it blocks the reflective lens mounted on the base of the tabber 3 Turn the sensitivity adjustment on the top of the sensor fully counterclockwise to the minimum sensitivity position 4 The turn it clockwise past the point at which the ORANGE light turns GREEN Remove the piece of media the light should be ORANGE Re insert the piece of paper and check that the light turns GREEN 6 Place a small amount of lacquer or nail polish on the adjustment MEDIA SENSOR 28 5 62477 Rev W360 Tabber Service Manual ADJUSTMENT Tabber and Feeder Speed Control Adjustment Part 1 Requirement The maximum speed must be no more than 100 ips Adjustment l 2 Open the Control Panel The speed control is
6. A W360 Tabber Service Manual CONDITION More than three stamps applied one after another on the media when 1 2 or 3 stamps are selected DIRECTION OF TRAVEL Tabber Operation Problems CONDITION Tabber flashes Exceeding Tabbing Rate warning while tabbing Tabber Stops while tabbing and displays Status Maximum Tabbing Rate Exceeded Tabber Stops while idling with no media going through it Advanced TROUBLESHOOTING SOLUTION Tab Stamp sensor adjustment improper Check Tab Voltage and Backing Voltage adjustments Page 21 SOLUTION Speed of tabbing exceeds maximum speed for the number of tabs being applied Slow down tabber Feeder speed is too fast leaving too little gap between pieces Slow down feeder or use the optional feeder connected to the tabber NOTE if this condition continues for more than 10 seconds thetabb er will stop and display the condition below Speed of tabbing exceeds maximum speed for the number of tabs being applied Slowdown tabber transport speed Feeder speed is too fast leaving too little gap between pieces Slow down feeder The Tabber is equipped with a transport timeout if no media is feeding after 30 seconds it will stop Pushing the Run key will restart it A diagnostic routing is built into the Tabber Software It can be accessed through the Operate or the Pass Thru screen Click on the Advanced Soft key and the Status Advanced screen will appear On
7. This is rare but possible when high gloss media 15 being used qualified service person should make this adjustment Tab Sensor Test Use the V Tab adjustment screen to check the live tab sensor voltage V value Not Interrupted Nothing in sensor Tab stock removed 0 12V or less If you removed all the tab material from the Tab Applicator and clean the tab sensor but it still reads higher than 0 12V this would indicate a dirty or damaged sensor If the tab sensor reads 3 30V or higher even when the sensor is not interrupted this would indicate a totally blocked damager or disconnected sensor If the Tab sensor does not respond correctly after being cleaned a qualified service person should be contacted to disassembly clean and possibly replace the tab sensor Cleaning Tab Wrap Guides Each of the Transport Belt assemblies has a tab guide that help to fold the tab over for sealing by the pressure rollers In the course of running a buildup of adhesive will restrict the tab from going into the guide Both of the guides and the slots should be periodically cleaned with a Q tip saturated with WD 40 to remove the adhesive residue and provide some lubrication 51 5 62477 Rev A W360 Tabber Service Manual MAINTENANCE Lubrication WARNING THE Tabber AND FEEDER ARE PRECISION MACHINES THAT SHOULD BE CLEANED REGULARLY TO INSURE MANY YEARS OF SERVICE BEFORE PERFORMING ANY MAINTENANCE DISCONNECT THEM FROM THEIR POWER
8. Turn the Tabber over on its back rear cover 3 Remove the two motor mounting screws 1 and then set the Tabber back on its feet 4 Remove the Left hand Side Cover the Non operator Side Cover and the Control Panel Cover 5 Unplug the motor from the Motor Speed control PC Board NOTE THE CABLE IS HELD TO OTHER WIRES BY TIE WRAPS THESE WILL HAVE TO BE CUT AND REPLACED WHEN REASSEMBLING 36 5 62477 Rev W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY 6 Loosen the adjustment Allen screw 2 on the Double Pulley 7 Remove the Drive Belt 3 and the two Allen screws 4 and then remove the Motor 8 Reassemble in reverse order making the belt tension adjustment after the two mounting screws on the bottom of the Tabber are installed WHEN ROUTING OF THE WIRE TO THE SPEED CONTROL MAKE SURE THAT YOU REPLACE ANY TIE WRAPS THAT WERE REMOVED 9 Replace the covers and test the operation of the Tabber 37 5 62477 Rev A W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY Replacing Sandpaper on Tab Drive Roller 1 Turn the Tabber on and set the speed control to Q Press the start button to cause the brake to activate This will lock the drive roller so that the Allen screw can be removed 2 Remove the Allen screw that attaches the tab driver roller to the drive shaft and remove the Sandpaper roller THE ALLEN SCREWS THAT APPLY PRESSURE TO THE ROLLER ARE REMOVED AS FOLLOWS HEAD 1 TU
9. 1 that hold the brake plate to the shaft Insert a 0 006 feeler gage between the brake and the brake plate Tighten the two Allen screws 1 Replace the covers 21 5 62477 Rev W360 Tabber Service Manual ADJUSTMENTS Tab Clutch Position Adjustment Requirement The tab must be placed in the position that 1s selected in the software NOTE THIS ADJUSTMENT SHOULD BE CHECKED EACH TIME A CLUTCH IS REPLACED IN EITHER HEAD Adjustment l After replacing a clutch in either head set up a job to place a tab 1 from the lead edge of a piece Run at least five 5 pieces and check the location of the tab on each one If it is 1 from the edge no adjustment 15 required If it is not measure the distance the tab 15 from the lead edge using the scale on the tabber control panel It is in tenths of an inch Turn off the tabber then hold down the CLEAR key and turn the tabber on In a few seconds the Enter Sensor offset 1 and press SAVE key screen will appear Enter Sensor offset 1 and press SAVE key Enter Sensor offset 2 and press SAVE key 0 000 Current Value 3 750 0 000 Current Value 3 750 Status Diagnostic Status Diagnostic Offset 2 EXIT OffsetiH EXIT O O O O U LI LI LI The default value 16 3 750 for both heads If the tab 15 too close to the lead edge enter a number in 0 010 increments that 1s greater than the default If the tab 1s farther from the lead edge of the piece enter a number
10. SOURCE Several locations on the Tabber Tabber require regular lubrication They are as follows 1 Place a small amount of White Lithium Grease the surfaces where the Head Assembly raises and lowers OPERATOR SIDE LEFT OPERATOR SIDE RIGHT EXIT END REAR SIDE 2 Lubricate the surface of the stepper cam for the head raise mechanism with white lithium grease as shown 52 5 62477 Rev W360 Tabber Service Manual APPENDIX Appendix A Specifications for Tabber ONE PASS TAB STANDARD TAB STAMPS MEDIA SIZE L X w MAX MEDIA THICKNESS TAB SIZE CALIBRATION TAB PLACEMENT SETTING TAB SENSOR CALIBRATION MEDIA HEIGHT ADJUSTMENT TAKE UP SPOOLS PRODUCTION RATE PRODUCTION RATE CALCULATED WITH REEL CAPACITY DIMENSIONS WEIGHT 1 3 per side or 1 3 on 1side and 1 front Minimum 3 4 Maximum 1 1 2 to 3 Minimum 3 5 x 5 Maximum 11 x 15 Detachable Feeder 12 x 17 1 4 Fully automatic or manual Manual or Automatic Manual or Automatic Heads Standard Two sides tabbed simultaneously 1 tab 25 000 h Two sides tabbed simultaneously 2 tabs 15 000 h Two sides tabbed simultaneously 3 tabs 10 000 h Tri fold 8 1 2 x 11 Two reels 10 diameter each 28 W X 26 H with reels x 34 L with feeder 97 Ibs Specifications are subject to change without notice 53 5 62477 Rev A W360 Tabber Service Manual APPENDIX Appendix B Identifying the Tab Types
11. Tab Sensor test 5 Head 2 Tab Sensor Tests that the tab sensor in Head f 2 is working This test should be conducted with the tabs removed from the tabber piece of paper inserted into the sensor should cause the display to change from UNCOVERED to COVERED Press Next to proceed to the Media Sensor Test 6 Media Sensor Tests that the Media Sensor is working properly Place a piece of paper between the sensor and the reflective lens The screen should go from UNCOVERED to COVERED Press Next to proceed to the Keyboard Test 7 Keyboard When in the keyboard test mode each time you press a key the display should show the name of the key in the Key Pressed line Press EXIT last to return to the Advanced screen and exit the tests Head 1 Tab Sensor State UNCOVERED Status Diagnostic Previous Head 2 Tab Sensor State UNCOVERED Status Diagnostic Previous Media Sensor State UNCOVERED Status Diagnostic Previous Keyboard Test Key Pressed Status Diagnostic This concludes the diagnostic testing Any returns that do not match the above indicate a problem with the component tested 18 5 62477 Rev A W360 Tabber Service Manual ADJUSTMENTS SECTION 4 Adjustments Motor Drive Belt Requirement The drive belts must have the proper tension Adjustment 1 Unplug the machine from its power source 2 Remove the four screws and remove the rear cover ay lt a
12. in and turned on Jams CONDITION Media jams in transport section of Tabber Tabs jam in tab guide Side Tab Tears and does not seal to the bottom of the piece Piece may be wrinkled SOLUTION 1 Check alignment of Feeder to Tabber Media should be feed between 1 16 to 1 32 from the fixed guide in the tabber Check that the two paper guides are not pressing down too firmly on the media Check that the adjustable center guide is not pushing the paper tightly against the fixed side guide Check that the head pressure is not too tight Clean the Tab guides See Maintenance Section Side guide too tight against the media Open the width of the guide SV62477 Rev W360 Tabber Service Manual TROUBLESHOOTING Tab Placement Problems CONDITION Tabs not placed the same spot on Tabs should be placed within 1 8 the media 1 Check the pitch setting for the tab It should be slightly more than the tab size plus the space between the tabs Check the amount of head pressure Too little can cause the media to slip when it 1s being fed Check that the pointer on the applicator head is in the center of the tab Check that the tabs are threaded properly Are they behind the Reel Brake Roller Arm More of the tab is on the top of the media Adjust the fine adjustment Knob 1 or 2 than on the bottom depending on the head that requires adjustment See Fine Tuning A
13. is located on the base of the machine Set the Auto Manual Switch on the Feeder to the Manual position Pre set the IR Comp pot to the 10 o clock position and the Current Limit pot to the 11 o clock position 3 Turn on the Feeder power switch Adjust the Motor Speed Control knob on the control panel to 0 The rollers should not be moving at this point If they are adjust the Min Speed potentiometer 1 on the Motor Control PC Board so that the rollers do not turn Turn the Motor Speed Control knob to position 1 The rollers should be moving at slow speed Set the Auto Manual Switch to Auto and feed some media with the tabber speed control set at maximum Adjust the Max Speed pot 2 on the feeder so that there 15 a minimum of l 1 2 gap between the pieces being fed Turn off the machines and replace the covers ee LOST YA PF w FEEDER MOTOR SPEED CONTROL PCB 30 5 62477 Rev W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY SECTION 5 Disassembly and Assembly The following will assist you in disassembling the Tabber for servicing DISCONNECT THE Tabber AND THE FEEDER FROM THE POWER SOURCE BEFORE ATTEMPTING ANY DISASSEMBLY Tabber Disassembly Removing the Reel Assembly 1 Remove the upper screw that holds the Reel Assembly to the Tabber and loosen the lower screw Lift the Reel Assembly from the machine 2 Reassemble reverse order 31 5 62477 Rev A W360 Tabber
14. is not even adjust the cam roller eccentric 5 on the non operator s side The Cam roller eccentric 1s accessible through the hole in the rear side frame If the pull is not even on the operator side when the bridge 15 all the way down go to step 11 23 5 62477 Rev A W360 Tabber Service Manual ADJUSTMENTS 7 10 Place two strips of 90 t paper between the Turn the two Applicator Head Stop Cams to their lowest position making sure that the stop does not touch the cam as shown Loosen the lock nuts on the two latch screws and raise the screws forwarding rollers on the Applicator Head assembly and the Transport Belts and close the Applicator Head assembly Check for an even pull on the strips Turn the screws to a point below the latches and then unscrew them until the latch just closes against the screw back off an additional 1 4 turn Tighten the lock nuts while making sure the screws do not move Check for an even pull on both sides The pull should be even on both sides Also put two strips of 90 paper under the two entrance guides Check that when the strips are pulled you can feel the Balls turning in the belt guide Adjust the two eccentric stops against the Applicator Head until they just touch as shown in the before and after illustration 24 5 62477 Rev W360 Tabber Service Manual ADJUSTMENT NOTE The adjustment below is only done if the pull on the paper is less on the operator side
15. of the machine 11 If the pull on the Operator Side is not correct after the above adjustment 1s performed remove the screw 1 that holds the Cam pin in place on the side frame Loosen the collar on the inside of the front cover that holds the positioning drive gear in place and pull the Raise and lower knob toward you to release the Drive Gear 2 from the Raise and Lower Gear 3 NOTE When reassembling after making this adjustment make sure that the stop pin is in its proper or 0 position 12 The front or right hand cam shaft that is part of the raise and lower geer should allow the head to be in its lowest point where the operator side of the exit rollers touch If the cams do not allow the head assembly to bottom out the grasp the rear shaft 4 with a pair of pliers and turn the Raise and Lower gear 3 to slip the belt on the pulleys until the head sits evenly front to back DO NOT LOOSEN OR REMOVE THE CAMS TO ADJUST THE BRIDGE ASSEMBLY DOING SO WILL MAKE REASSSEMBLY DIFFICULT 13 Reassemble the Raise and Lower Drive Gear 2 making sure that the timing mark matches the timing mark on the Raise and Lower Gear 3 Reinstall the Cam Pin assembly 1 Then go to Step 3 through 10 and repeat the adjustments 25 5 62477 Rev A W360 Tabber Service Manual ADJUSTMENTS Power Supply Adjustment Requirement Provide proper output from power supply to machine Adjustment 1 Remove rear cover and the l
16. that 15 less than the default in increments of 0 010 Enter the number and press SAVE Increase Decrease Value Value If you wish to adjust Head 2 press the Offset 2 soft key otherwise enter a number press SAVE Then press EXIT This will return you to the operate screen Run at least five 5 pieces to check the adjustment NOTE The Center Tab position is adjusted by the operator in the software 22 SV62477 Rev A W360 Tabber Service Manual ADJUSTMENT Head Assembly Alignment Requirement The Pressure rollers must be parallel and provide pressure to seal the tab for both heads Adjustment 1 Position Head 1 at its closest point on the operator side of the Tabber 2 Unplug the Tabber from the power source Then Open the front Control Panel and remove the rear and right hand covers 3 Turn the raise and lower gear until the head assembly is at its lowest point on the cams assembly on the operator side of the tabber The point at which the timing marks on the gears match 4 Place two strips of 90 r7 card stock between F the two sides of the Applicator Head exit rollers and check for an even pull NOTE The pressure required to pull the strips of paper should not be excessive 5 Also put two strips of 902 paper under the two entrance guides Check that when the strips are pulled you can feel the Balls turning in the belt guide 6 If the pull on the paper on the non operator side
17. the Center Support Plate and the Guide from the Tabber 8 Remove the Two Support Rods screws 9 Slide the Rods toward the Rear of the Tabber 10 Remove the two screws and the Drive Roller Bearing from the Operator s side of the Tabber 43 5 62477 Rev W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY 11 Remove the two screws in the Drive Roller bearing at the rear of the Tabber and slide the roller toward the front of the machine This will provide clearance for removing the belts Removing Transport Belt on Head 2 12 Remove the tab guide plate from the transport assembly two Allen screws 13 Slip the belt off the front guide roller and then slide it off the Drive Roller 14 Then remove it from the Drive Roller at the rear 44 5 62477 Rev W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY Removing Transport Belt on Head 1 15 The Transport belt on Head 1 is removed in the same manner as on Head 2 with the exception that the Belt Guide must be removed before the belt can be removed The belt guide is held in place by two screws 16 Reassemble in reverse order and then check the Tab Guide adjustment and the Motor Drive belt tension adjustment Feeder Disassembly Removing Covers 1 Unplug the feeder from it power source 2 Remove the Speed Control Knob and the two screws circled from the operator s side of the feeder Then lift the cover from the machine 3
18. this screen in addition to Diagnostics the Backlight on the LCD Display can be adjusted for intensity and you can display the Version of the software along with the Lifetime Products and Lifetime Tabs on both heads Below is a flowchart of the functions for Advanced 15 SV62477 Rev A W360 Tabber Service Manual TROUBLESHOOTING Press Run to tab using Job 1 Status Pieces 0 Job Pass thru Advanced Press Run fro pass thru mode Status Pieces 0 Job Operate Advanced Status Advanced Backlight Version Diagnostic Status Advanced 50 Lifetime Products 7 Lifetime Tabs 9 21 Bios Version v8800 r07 01 Pressing the BACK key will return the Tabber to the previous screen Diagnostics A diagnostic function 1s built into the Tabber software The Diagnostics are accessed through the Advanced key Pressing the Diagnostic key will start the tests 1n order To pass a test simply press the Next key to return to a test press the Previous key The tests in order are 1 Voltage Test Displays the voltages in the power supply and logic Voltage Test 1 0 000 V2 0 000 V3 0 000 V4 0 000 Status Diagnostic Test ON Next 16 5 62477 Rev W360 Tabber Service Manual When you click on Test ON V 1 should be 12 0 volts for the main power supply V 2 V 3 and V 4 are voltages on the logic board Click EXIT to return to the Voltage Test screen or Next to go to the next test 2 Encoder Test Tes
19. 00 78 Brake Head 2 41 500 18 Clutch Head 1 29 103 08 41 500 19 Clutch Head 2 123 0312 l y 40 5 62477 Rev W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY NOTE The Clutch and Brake for each head have different part numbers 9 Remove the Brake by removing the three screws that attach 1t to the side frame There are three access holes 1n the outer frame to permit access NOTE A little dab of grease on the end of the Phillips Screw Driver will make it easier to reassemble the Clutch and Brake 9 Reassemble in reverse order Make sure that the two washers are properly installed Refer to Step 7 for their location When you have finished the assembly adjust the Brake Plate Then test run the machine and check the tab placement before replacing the covers Replacing Transport Belts l Unplug the Tabber Remove the Control Panel Rear cover and Left hand cover Loosen the drive belt adjustment and remove the drive belt from the Rear Drive Roller pulley 41 5 62477 Rev A W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY 4 Remove the Drive Pulley from the Drive roller shaft 5 Loosen the Exit Roller drive pulley and the Drive Roller pulley Remove them and the Roller Drive Belt from the Tabber 6 Remove the two pulleys and the belt from the Drive Roller and the Encoder 42 5 62477 Rev W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY 7 Remove
20. LY Notes 48 SV62477 Rev A W360 Tabber Service Manual MAINTENANCE SECTION 6 Maintenance This section describes maintenance that an experienced operator can perform If any service or maintenance beyond which is described in this document is required please contact your local dealer Cleaning WARNING THE Tabber AND FEEDER ARE PRECISION MACHINES THAT SHOULD BE CLEANED REGULARLY TO INSURE MANY YEARS OF SERVICE BEFORE PERFORMING ANY MAINTENANCE DISCONNECT THEM FROM THEIR POWER SOURCE The Tabber and Feeder must be cleaned regularly of accumulated paper dust and ink Depending on the types of media that are run paper dust may accumulate within machines and on the transport To clean unplug both machines from the power receptacle and then remove the covers The internal areas are best cleaned with a vacuum that has a soft brush attachment to help loosen the dust particles Take care not to damage the PC Boards or electrical wiring The exterior of the machine may be cleaned with any standard household cleaner which is non abrasive and does not contain plastic harming solvents NEVER SPRAY OR POUR CLEANERS DIRECTLY ON OR INTO THE Tabber OR FEEDER EXCESS LIQUID COULD HARM ELECTRONIC PARTS ALWAYS DAMPEN A RAG WITH THE CLEANER AND APPLY IT TO THE PARTS TO BE CLEANED Rollers and Transport belts The belts and rollers can become glazed with paper lint and ink from the media They should be regularly cleaned wi
21. R 5 62477 Rev W360 Tabber Service Manual TABLE OF CONTENTS Section 6 Maintenance Cleaning Rollers and Transport Belts Cleaning the Sensors Media Sensor Test Tab Sensor Test Cleaning the Tab Wrap Guides Lubrication Appendices A Specifications B Identifying Tab Types C Wiring Diagrams Index ii SV62477 Rev A W360 Tabber Service Manual GETTING ACQUAINTED SECTION I Getting Acquainted Front View Control Panel The machine is controlled and programmed from this panel Head 1 Fine Tuning Adjustment This Knob permits fine positioning of the Tabs on Head 1 Head 2 Fine Tuning Adjustment This Knob permits fine positioning of the Tabs on Head 2 Head 1 This head can apply stamps or tabs on either the edge or end of the media Head 2 This head can only apply tabs on the edge of the media Take up Reels The tab web is wound up here after the tab 1s applied Left Media Guide Assembly Transports the media to the tabbing area This guide is not adjustable Main Power Switch amp Receptacle Tabber The power cord is plugged here and the switch turns the Tabber On and Off Center Support Plate Used to support media 6 5 wide or larger This plate also contains the slot used when tabbing at the lead edge of a piece Right Media Guide Assembly This guide transports the media to the tabbing area and 15 adjustable for the width of the media Media Thickness Adjustment Knob Ad
22. RN THE SCREW COUNTERCLOCKWISE TO REMOVE AND HEAD 2 CLOCKWISE TO REMOVE 3 Repeat the steps in reverse after replacing the sand paper roller Tighten the Allen screw to compress the rubber roller and hold the sandpaper roller in place 38 5 62477 Rev W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY Replacing Clutch and Brake NOTE Both Head 1 and Head 2 clutch and brake are removed in the same manner 1 For Head 1 remove the cover over the head assembly For Head 2 remove the rear cover from the Tabber In either case cut the Tie Wrap that 1s holding the wires in place 2 Use a screwdriver to push the clutch toward the brake Remove the pin from the rear of the clutch by pushing it out with a small piece of wire Set the pin aside 3 Loosen the two screws that hold the brake plate to the shaft 4 Continue by removing the screw that holds the Sandpaper Roller and rubber roller assembly 39 5 62477 Rev A W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY 5 Remove the Allen screw washer sandpaper roller rubber drive roller and the washer behind the drive roller and set aside 7 Pull the Shaft out of the assembly by pulling it from the Sandpaper roller side of the assembly The belt will be freed when the shaft 1s removed NOTE The arrow points to a key in the shaft that holds the brake face in place 41 121 03 29 103 06 Pulley 41 500 79 Brake Head 1 27 102 10 41 5
23. Remove the two screws circled from the non operator s side of the feeder and lift the cover from the machine 45 5 62477 Rev A W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY Replacing Feed Rollers l 2 Remove Side covers from the machine Lock the upper forwarding rollers in the maximum open position by loosening the locking screw and rotating the lever clockwise then tightening the locking screw Remove the two screws that attach the side guide to the feeder and remove the side guide Remove the seven screws that attach the front plate to the feeder There are two screws on each side and three across the top behind the feed roller Remove the bearings from each side of the roller shaft and remove the roller and shaft assembly from the machine Replace the rollers and reassemble 46 SV62477 Rev A W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY Feeder Front View Motor Speed Control er Forwarding Rollers 3 Uppe r Forwarding Rollers Rollers Removing the Drive Motor 10 11 12 13 14 I5 Unplug the feeder from its power source Remove the non operator side cover Unplug the motor from the Motor Speed control PC Board Remove the Take up Roller by removing the Allen screw 1 Remove the four screws 2 that attach the motor to the feeder frame Reassemble in reverse order 47 5 62477 Rev A W360 Tabber Service Manual DISASSEMBLY AND ASSEMB
24. Service Manual DISASSEMBLY AND ASSEMBLY Tab Applicator Removal and Disassembly Dry compressed air should be used to clear dust from the inside of the Tab Applicator Assemblies and Tab Sensors Never use liquids to clean sensors To clear tabs stamps and adhesive from inside the Tab Applicator Assemblies and Tab Sensors the Tab Applicator Assemblies can be removed from the heads and disassembled for cleaning CAUTION Be careful of wire connections when performing this task DURING RE ASSEMBLY MAKE SURE SENSORS ARE PROPERLY SEATED INTO PLATE OPENINGS 22 5 62477 Rev W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY Removing Front Cover 1 Remove the four screws from the Front Cover hinge the cover forward to gain access Encoder 4 Transport Motor Relay 2 I O Relay 5 Speed Control Relay 3 Power Supply 6 Motor Speed Control 3 Components inside front cover 1 Transport Power Switch 4 Interface Cable 2 Transport Speed Control 5 Control PC Board and Display 3 Main Processor PC Board 6 Emergency Stop Switch 33 5 62477 Rev A W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY Removing Rear Cover 1 Remove the four screws holding the cover in place and remove the cover 2 Components under rear cover 3 wy Me BS LN l 99 m a L 1 Main Drive Motor Line Filter I O PC Board Emergency Stop Input Emergency Stop Output SAL dv DL gore 34 p
25. abber Service Manual GETTING ACQUAINTED Tabber Control Panel 1 9 TRANSPORT EMERGENCY STOP 1 Transport Power Switch Turns the Tabber transport power ON NOTE The Transport Power will not activate unless all of the safety and emergency switches are closed 2 Speed Control Adjusts the speed of the Tabber NOTE The maximum speed of the Tabber tabber is controlled by the software The speed of the tabber for applying single tabs to one side of a piece is 25 000 pieces per hour for applying double tabs to one side of a piece it is 15 000 pieces per hour and for applying triple tabs to one side of a piece is 10 000 pieces per hour Exceeding these speeds will cause the tabber to stop The Tab placed on the end of the piece is not counted in the above LED Display Keeps the operator informed of the status of the Tabber Key Pad Used to enter the data to program the Tabber Emergency Stop When the Tabber is properly connected to the feeder and or other pieces of equipment activating this button will stop the machines Soft Keys The soft keys are used to step through the various menu options to program the Tabber 7 Stop Key Pressing this key will stop the Tabber and hold it in a ready state to resume operation Run Key Pressing this key to start the Tabber when running job IKA Info Kev Pressing this kev will change the displav to the information mode Save Key This key is used to sa
26. control the emergency stopping of another machine 3 Convevor Interface The W985 Stacker is connected here to control the Tabber Operation Tabber Feeder Connection The feeder is connected here to permit automatic operation of the feeder when used with the Tabber 5 Main Power Switch Tabber This switch turns the Tabber On and Off Fuse The main power fuse 2 5A 250V for the Tabber is located here Caution Disconnect the power before replacing the fuse Power Inlet Tabber The power cord is plugged in here 3 5 62477 Rev A W360 Tabber Service Manual GETTING ACQUAINTED Feeder and Connections Tabber Feeder Control Cable This connection permits the tabber to control the feeder when the mode switch 1s 1n the Automatic Position Power Inlet Feeder The power cord is plugged in here Fuse The feeder fuse 1s located here 4 Main Power Switch Feeder This switch will turn the feeder On and Off 5 Mode Switch The mode switch permits selection of either the Automatic Mode the tabber controls the Feeder or Manual Mode the feeder speed 15 controlled manually by the Feeder Speed Control Feeder Speed Control When the feeder mode switch is in the manual position this knob controls the speed of the feeder Media Thickness Adjustment Feeder Loosening the knob and repositioning the lever 15 used for adjusting the exit rollers of the feeder for thicker media 4 SV62477 Rev W360 T
27. djustments for more detail DIRECTION OF TRAVEL DIRECTION OF TRAVEL Less of the tab is on the top of the media Adjust the fine adjustment Knob 1 or 2 than on the bottom depending on the head that requires adjustment See Fine Tuning Adjustments for more detail DIRECTION OF TRAVEL Lead edge tab is more on the top than the This adjustment is performed by the bottom software See Head 1 Tabbing at the Lead Edge of a Piece in the Operating Instruction Section DIRECTION OF TRAVEL MORE TAB ON TOP 12 SV62477 Rev A W360 Tabber Service Manual Tab Placement Problems continued CONDITION Lead edge tab is more on the top than the bottom DIRECTION OF TRAVEL MORE TAB ON BOTTOM Tab is not flush with the edge of the media DIRECTION OF TRAVEL When double tabbing one tab is not placed properly on the edge of the media um DIRECTION OF TRAVEL Two or three tabs applied next to each other DIRECTION OF TRAVEL TROUBLESHOOTING SOLUTION This adjustment is performed bv the software See Head 1 Tabbing at the Lead Edge of a Piece in the Operating Instruction Section Media is not being fed flush with the fixed side guide There should not be more than 1 16 to 1 32 space between the media and the fixed side guide when the media enters the tabber The media may not be traveling along the fixed side guide Adjust the angle of the guide rollers by turning the knob on the skew guide Check the pressu
28. e e cre Tabber Feeder Connection Main Power Switch Tabber Fuse Power Inlet Tabber 5 62477 Rev W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY Removing the Left hand Side Cover 1 Remove the two screws from the cover and then remove the cover 1 Main Drive Motor 12 Volt DC Power Supply 2 Main Drive Roller Encoder Encoder and Encoder Drive Belt 1 The Encoder and Encoder Drive Belt are located under the front cover panel on the left hand side of the tabber body 2 To remove the Encoder or replace the Encoder Drive belt loosen the two screws on the drive roller 1 remove the pulley and belt 3 To remove the Encoder remove the four screws 2 that mount the encoder to the frame 4 Reassemble reverse order 35 5 62477 Rev A W360 Tabber Service Manual DISASSEMBLY AND ASSEMBLY Replace the Take up Reel Drive Belts l 5 6 To replace the Take up Reel Drive belt on Head 1 remove the cover over the Take up Reel drive assembly To replace the Take up Reel Drive belt on Head 2 remove the rear cover from the tabber Remove the Tru Arc 1 from the Take up Reel shaft Slide the Take up Reel assembly away from the support bearing Remove the old belt and install a new one Slide the Take up Reel assembly back into the bearing and reinstall the Tru Arc Replace the cover Replacing the Drive Motor 1 Unplug the feeder from its power source 2
29. eft hand side cover and connect voltmeter probe to GND 1 and 12V 2 on Interface PC Board Turn the tabber ON 2 Adjust V1 ADJ potentiometer 3 on the Power Supply module to obtain 12 0 VDC 0 1 V THE ADJUSTMENT IS NEAR THE CONNECTION POINTS FOR THE INPUT AND OUTPUT OF THE POWER SUPPLY USE A NON CONDUCTING TOOL FOR MAKING THE ADJUSTMENT AND PUT THE TOOL IN PLACE BEFORE TURNING ON THE Tabber POWER 3 Turn the tabber OFF apply lacquer such as nail polish to the potentiometer and replace the cover A ul a INTERFACE PC BOARD POWER SUPPLY 26 SV62477 Rev A W360 Tabber Service Manual ADJUSTMENT Tab Sensor Adjustment Head 1 and Head 2 Requirement Adjust the Tab Sensor so that it can automatically detect the tabs in the machine and that the voltages are equal Adjustment 1 Remove the rear cover from the tabber 2 Remove the Tabs from both of the heads 3 Place a Business Card in each sensor 4 Locate the Tab Sensor potentiometers on the I O PC Board upper right hand corner 5 Attach a volt meter to GND 1 and to one of the Sensor Output connections Head1 2 or Head 2 3 Turn on the Tabber and adjust the potentiometer to obtain 3 0 V DC Then adjust the second potentiometer for 3 0 V DC 6 Remove the Cards install tabs and use the software to set the V Tab voltages for each head 7 Replace the rear cover on the tabber JJ wor 1 it Hos d
30. justs the Heads and Pressure Rollers to the thickness of the media Media Width Fine Adjustment This knob fine tunes the media guide for the width of the media 1 562477 Rev W360 Tabber Service Manual GETTING ACQUAINTED Exit End View Head 2 Fine Tuning Adjustment This Knob permits fine positioning of the Tabs on Head 2 Center Plate The Center Plate supports media wider than 6 5 and the slot in the middle is used when tabbing on the end of a piece Exit Foot This device holds the media down aw it travels under the exit rollers It 15 adjusted with Head 1 Tab Wrap Guide Head 1 When side tabbing this guide wraps the tab around the media Exit Pressure Rollers These rollers provide the pressure to transport the media and seal the tabs Tab Wrap Guide Head 2 When tabbing on this head the guide wraps the tab around the media Exit Foot Knob This knob is used to position and secure the exit foot 6 Exit Roller Assembly Securing Latches These latches are used to lock down the exit roller assembly 2 SV62477 Rev W360 Tabber Service Manual GETTING ACQUAINTED Tabber Electrical Connections 1 Emergency Stop Input This connector when wired into an existing safety circuit permits an emergency stop on from the existing circuit to stop the Tabber The jumper plug is required when this feature is not used Emergency Stop Output This connector permits the Tabber to
31. ke sure that the emergency stop switch of the Tabber is the OFF position and the main power switch above the power cord receptacle 15 the OFF position Make sure that the power switch on the feeder 15 in the OFF position also 1 Connect one end of the Tabber power cord 1 to the rear of the Tabber in the corresponding receptacle 2 Connect one end of the Feeder power cord 2 to the rear of the Feeder in the corresponding receptacle 3 Plug the other end each cord into a 115 220 Volt AC 50 60 Hz Grounded outlet 8 5 62477 Rev W360 Tabber Service Manual ASSEMBLY AND INSTALLATION DO NOT USE ADAPTER PLUGS OR EXTENSION CORDS TO CONNECT THE Tabber OR THE FEEDER TO THE WALL RECEPTACLE DO NOT USE OUTLETS CONTROLLED BY WALL SWITCHES DO NOT USE AN OUTLET THAT SHARES THE SAME CIRCUIT WITH LARGE ELECTRICAL MACHINES OR APPLIANCES 4 Connect the Feeder Interface cable 3 to the Feeder and to the lower connector on the Tabber 9 SV62477 Rev A W360 Tabber Service Manual ASSEMBLY AND INSTALLATION Notes 10 5 62477 Rev A W360 Tabber Service Manual TROUBLESHOOTING SECTION 3 Troubleshooting The following trouble shooting guide is provided to assist you in solving any problems that might occur with the Tabber Tabber We have tried to make it as complete as possible The best advice we can offer 1s to make sure that the tabs labels or stamps are threaded properly and that the machine is plugged
32. located on the left hand side Pre set the IR Comp pot to the 10 o clock position and the ACCEL to the 11 o clock position Turn on the Tabber and turn on the Transport Power Press the RUN button to start the tabber Put a voltmeter between points A and B and adjust the Current Limit pot for 1 5 VDC 5 Adjust the Motor Speed Control knob on the control panel to 0 The belts should not be moving at this point Adjust the Min Speed potentiometer 1 on the Motor Control PC Board until the belts just turn then turn the pot so that the belts do not turn Turn the Motor Speed Control knob to position 1 The belts should be moving at slow speed Turn the Motor Speed Control knob to position 10 The belts should be moving at a speed of 250 feet per second as measured with a tachometer This is equivalent to a 25 0 KHz signal on the I O PC Board at GNDI and SIG A Adjust the Max Speed potentiometer 2 on the Speed Control PCB Turn off the Tabber and replace the covers pias gia un mmm Paama 018 vm x lt me mz wi e LI To L Cel 11 00 Tabber MOTOR I O PC BOARD SPEED CONTROL PCB 29 5 62477 Rev A W360 Tabber Service Manual ADJUSTMENTS Tabber and Feeder Speed Control Adjustment Part 2 Requirement The maximum speed must be less than the speed of the Tabber when it 1s operating in the Auto Mode Adjustment 1 Remove the operator side covers The speed control
33. rake Replacing Feed Rollers Replacing Sandpaper on Tab Drive Roller Replacing Take up Reel Drive Belts Replacing the Drive Motor Replacing Transport Belts 5 Specifications Stamp Placement Problems Tab Applicator Removal and Disassembly Tab Brake Adjustment Head 1 and Head 2 Tab Clutch Position Adjustment Tab Guide Plate Alignment Tab Placement Problems Tab Sensor Test Tab Web Sensor Adjustment Head 1 and Head 2 Tabber and Feeder Speed control Adjustment Tabber Control Panel Tabber Electrical Connections Tabber Operation Problem Tabber Wiring Diagram Troubleshooting W Wiring Diagrams 58 19 25 45 33 34 31 47 39 46 38 36 36 41 53 14 32 21 22 20 12 51 26 28 15 57 11 55 SV62477 Rev A Pitney Bowes 1 Elmcroft Road Stamford Connecticut 06926 0700 www pitneybowes com PB Form SV62477 Rev A 6 10 02010 Pitney Bowes Inc All Rights Reserved Printed in the USA 5 62477
34. re between the head and the transport Too much pressure will cause the media to flex as it 1s transported Too little pressure can cause the media to skew as the tab 1s being applied Programming issue When programming the multiple tabs Together was selected instead of Separate Reprogram the job 5 62477 Rev A W360 Tabber Service Manual TROUBLESHOOTING Tab Placement Problems continued CONDITION SOLUTION More than three tabs applied on each Tab sensor adjustment improper Check piece Tab Voltage and Backing Voltage adjustments Page 21 DIRECTION OF TRAVEL SOLUTION Stamps are not placed in the same place Stamp placement should be within 1 8 on the media 1 Check the pitch setting for the stamp It should be slightly more than the stamp size plus the space between the stamps Check the amount of head pressure Too little can cause the media to slip when it 1s being fed When applied the Stamp is not aligned on The media may not be traveling along the media the fixed side guide Adjust the angle of the guide rollers by turning the knob on the skew guide Check the pressure between the head and the transport Too much pressure will cause the media to flex as it 1s transported DIRECTION OF TRAVEL Two or three stamps applied evenly Programming issue When programming spaced multiple stamps Separate was selected instead of Together Reprogram the job DIRECTION OF TRAVEL 14 5 62477 Rev
35. ses and can radi ate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications Operation of this equipment in a residential area is likely to cause inter ference in which case the user will be required to correct the interference at his own expense CAUTION Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Shielded I O and USB cables must be used with this equipment to ensure compliance with the limits Use of unshielded cables is prohibited June 2010 02010 Pitney Bowes Inc Due to publication lead times and continuing product development this manual may not reflect final product release configurations and recommended service procedures Equipment and material specifications as well as performance features are subject to change without notice Available product features may vary depending on machine model system software level and system setup Some product features may be country specific Postage By Phone and E Z Seal are trademarks or registered trademarks of Pitney Bowes Inc ENERGY STAR is a registered trademark of the United States Environmental Protection Agency Other company names products or services mentioned herein may be protected by trademarks registered trademarks or service marks and are the property of their respective o
36. th a mild abrasive household cleaner on a damp cloth Avoid using solvents on the rubber rollers 49 5 62477 Rev W360 Tabber Service Manual MAINTENANCE Shafts with movable parts of the shafts that have parts of the machine moving on them should be cleaned with a soft cloth THE BEARINGS ON THE MOVING PARTS SUCH AS TAB HEAD 1 AND THE TRANSPORT BELT ASSEMBLIES ARE OIL LESS NYLON DO NOT PUT ANY SOLVENTS OR OIL ON THEIR SURFACES Cleaning the Sensors There are three sensors in the tabber two tab sensors one on each of the applicator heads and one media sensor located on the Head 2 Transport Belt assembly These sensors should be clean and free of accumulated paper dust Use dry compressed air to remove the dust WARNING DO NOT USE ABRASIVES OF ANY KIND ON THE SENSOR LENS The sensor locations are as follows EcL tan T Pu Hos Li 1 he AA SW er cd E 55 2 HEAD1TABSENSOR HEAD2TABSENSOR MEDIA SENSOR 50 5 62477 Rev W360 Tabber Service Manual MAINTENANCE Media Sensor Test There are two LED s located on the entrance side of the Media Sensor Green LED ON Power Present Orange LED ON No Paper not interrupted Orange LED OFF paper Present interrupted If the orange LED 15 not on when there is no paper present then the reflector may need to be cleaned If the Orange LED comes ON even when paper is present then the sensor intensity may need to be lowered
37. ts if the encoder is working When you click on Test ON a number will display 1n the Reading rotate the exit roller if the number changes the encoder is working Click Next to go to the next test TROUBLESHOOTING Voltage Test 1 12 00 V2 5 00 Status Diagnostic Test OFF V4 1 50 V3 3 30 Next Encoder Test Reading 0000000000 Status Diagnostic Test ON Previous Encoder Test Reading 12635167 Status Diagnostic Test OFF Previous REMOVE THE TABS FROM BOTH HEADS FOR THE REMAINING TESTS 3 Clutch Brake Test Tests the function of the clutch and brake for both of the heads at the same time The test OFF position has the Clutch and the Motor Off Clicking on Test ON will cause the Clutch and Motor to turn on and the Brake to go off You should be able to hear this action Use the Next key to go to the next test 17 Clutch Brake Test State Clutch OFF Brake ON Motor OFF status Disgnostic Test ON Previous Next EXIT Clutch Brake Test State Clutch Brake OFF Motor Status Disgnostic Test OFF Previous Next 5 62477 Rev A W360 Tabber Service Manual TROUBLESHOOTING 4 Head 1 Tab Sensor Tests that the tab sensor in Head is working This test should be conducted with the tabs removed from the tabber A piece of paper inserted into the sensor should cause the display to change from UNCOVERED to COVERED Press Next to proceed to the Head f 2
38. ve the entries into the memory Clear Key This key will clear any incorrect entry before it is saved in the memory Measuring Scale Use the scale to determine where to place the tabs 5 SV62477 Rev A W360 Tabber Service Manual GETTING ACQUAINTED Notes 6 5 62477 Rev A W360 Tabber Service Manual ASSEMBLY AND INSTALLATION SECTION 2 Assembly and Installation The Tabber is shipped in a single carton Assembly Choose a Location Place the Tabber with its feeder on a sturdy worktable or cabinet at least 12 inches from any walls Allow enough room to place the Feeder on the same work surface Protect the Tabber from excessive heat dust and moisture avoid placing it in direct sunlight THE UNIT IS HEAVY IT IS STRONGLY RECOMMENDED THAT TWO TECHNICIANS REMOVE THE Tabber FROM THE CARTON AND PLACE IT ON THE WORKING SURFACE Install Reel Supports The two Reel Supports have to be installed Loosen the lower mounting screw and slide the Reel Supports over the frame until they bottom on the lower mounting screw Then install and tighten the upper screw and lower screw 7 5 62477 Rev W360 Tabber Service Manual ASSEMBLY AND INSTALLATION Install the Optional Feeder 1 The pin A on the feeder should mate with the hole B on the Tabber body 2 When the feeder 1s properly aligned with the tabber body it will appear as in this picture Connecting Plugging in the Feeder and Tabber Ma
39. wners All rights reserved This book may not be reproduced in whole or in part in any fashion or stored in a retrieval system of any type or transmitted by any means electronically or mechanically without the express written permission of Pitney Bowes W360 Tabber Service Manual TABLE OF CONTENTS Section I Getting Acquainted Front View Exit End View Tabber Electrical Connections Feeder and Connections Tabber Control Panel Section 2 Assembly Installation and Operation Assembly Connecting Section 3 Troubleshooting Jams Tab Placement Problems Stamp Placement Problems Tabber Operation Problem Advanced Diagnostics Section 4 Adjustments Motor Drive Belt Tab Guide Plate Alignment Tab Brake Adjustment Head 1 and Head 2 Tab Clutch Position Adjustment Head Assembly Alignment Power Supply Adjustment Tab Web Sensor Adjustment Head 1 and Head 2 Media Sensor Adjustment Tabber and Feeder Speed control Adjustment Section 5 Disassembly and Assembly Tabber FEEDER Removing Reel Assembly Tabb Applicator Removal and Disassembly Removing Front Cover Removing Rear Cover Left Hand Side Cover Encoder and Encoder Driver Belt Replacing Take up Reel Drive Belts Replacing the Drive Motor Replacing Sandpaper on Tab Drive Roller Replacing Clutch and Brake Replacing Transport Belts Removing Covers Replacing Feed Rollers Feeder Front View Removing the Drive Roller TABLE OF CONTENTS SCAN rl
Download Pdf Manuals
Related Search