60 SLI Deck Supplement - Laird Manufacturing Corporation
Contents
1. CHECK BELT PERIODICALLY TO INSURE PROPER BELT TENSION DO NOT OVER TENSION KEEP THE INSIDE OF THE BELT HOUSING CLEAN AND FREE OF WATER KEEP THE IDLER ARM TENSIONER NUT JUST TIGHT ENOUGH TO DAMPEN THE IDLER ARM DO NOT OVER TENSION IDLER ARM TENSIONER NUT DEINES MANUFACTURING CORP LIMITED WARRANTY Deines Manufacturing Corp P O Box 266 Ransom KS 67572 proudly warrants to the original purchaser all products and components manufactured by Deines to be free of defects in material and workmanship Deines Manufacturing Corp does not warrant trade accessory items batteries engines generators transmission gear boxes etc which are warranted by their respective manufacturers Deines Manufacturing Corp will at its option replace or repair without charge to the purchaser for materials or labor any component or product manufactured by Deines found upon examination by any Deines Authorized Distributor or Dealer or by Deines at it s plant in Ransom KS to be defective in material and or workmanship To obtain warranty service the component or product must be returned to an Authorized Distributor or Dealer or to the Deines Plant TRANSPORTATION PREPAID accompanied by letter stating the warranty claim Upon receipt of a Warranty Claim Letter Deines will within ten business days commence performance of it s obligations under this Warranty This Warranty will commence upon the date of delivery and will extend as f2. 1 HHCS 5 16 NUT 5 16 LOCKWASHER NUT BELT GEARBOX 5 16 X 1 HHCS 5 16 LOCKWASHER KEY PULLEY W HUB SHIELD R amp L 5 16 X 3 4 5 16 LOCKWASHER GEARBOX PLATE 5 16 X 1 HHCS 5 16 LOCKWASHER PULLEY SETSCREW 5 16 X 5 16 PULLEY GEARBOX SETSCREW 5 16 X 5 16 NUT LOCKWASHER WASHER VEE IDLER NUT WAVY WASHER IDLER ARM 1 gt N N 02 02 SERIAL NUMBER amp UP FRICTION WASHER IDLER SPRING CHUTE 1 4 3 4 HHCS 1 4 LOCKNUT DECK HOUSING LH SKID SHOE 5 16 X 3 4 CARR BOLT 5 16 LOCKWASHER 5 16 NUT PIN CLIP RH CASTOR ARM IDLER ADJUST 1 4 X 1 HHCS 1 4 LOCKNUT HANDLE 1 4 X 3 4 CARR BOLT 1 4 LOCKWASHER Wow NNN N N 300 332 300 243 300 279 300 201 100 132 300 395 300 195 300 212 200 238 300 391 300 264 400 234 300 247 400 212 400 233 300 117 100 479 400 947 400 918 SHOWN 700 172 400 727 400 728 400 786 DESCRIPTION 1 4 NUT LH CASTOR ARM 3 8 X 1 3 4 CAR BOLT 3 8 LOCKWASHER 3 8 NUT ROLLER BRKT COTTER KEY ROLLER PIN ROLLER CASTOR STEM THICK SHIM GREASE FITTING ROLLER PIN FORK AXLE BEARING WHEEL amp TIRE TIRE ONLY WHEEL ONLY SPACER WEAR PLATE 5 16 X 1 1 4 HHCS 5 16 FLAT WASHER 5 16 LOCKWASHER CARRIER STRAP PLASTIC SLEEVE SHOULDER BOLT 3 8 16 NUT 3 8 LOCKW
3. THE BOTTOM BEARING PLACE THE TRASH SHIELD SLIDE THE SPACER OVER PLACE THE SQUARE KEY INTO THE KEY SEAT ON THE SHAFT AND INTO THE HOUSING AND SECURE WASHER OVER THE SHAFT THE SHAFT AND PRESS THE SLIDE THE PULLEY ONTO THE SHAFT SECURE THE PULLEY TO THE WITH THE SNAP RING AND SLIDE THE SHAFT BEARING ONTO THE SHAFT SHAFT WITH THE HEAVY WASHER LOCK WASHER AND THE BOLT INTO THE BEARING THEN PLACE THE MACHINE BOLT THE BLADE TO THE BOTTOM OF THE SHAFT WITH THE 5 8 BUSHING OVER THE SHAFT BOLT AND SPECIAL WASHER AND 5 8 LOCK WASHER m M SHOWN G N 60 SPINDLE ASSEMBLY AFTER SERIAL Y1909 47 jg PART NUMBER DESCRIPTION QUANTITY 300 466 3 8 24 X 1 HHCS 1 300 480 3 8 LOCK WASHER 1 300 173 WASHER 1 300 709 PULLEY 1 300 437 SET SCREW 2 300 278 MACHINE BUSHING 1 OR MORE 400 363 BEARING 2 400 366 SPACER 1 400 464 SPINDLE HOUSING 1 400 257 INTERNAL SNAP RING 1 400 465 TRASH SHIELD WASHER 1 300 288 KEY 1 400 466 SPINDLE SHAFT 1 400 468 WASHER 1 400 469 5 8 18X2 BOLT 1 400 467 BLADE 1 300 212A GREASE FITTING 1 300 517 5 8 LOCK WASHER 1 400 470 COMPLETE SPINDLE LESS BLADE 400 470 60 COMPLETE SPINDLE WITH BLADE 13 14 11 12 15 10 60 SPINDLE ASSEMBLY PRIOR TO SERIAL Y1909 REF PART DESCRIPTION QUANTITY 1 300 173 WASHER 3 2 300 709 PULLEY 3 3 400 261 SHAFT 3 4 400 363 BEARING 6 5 400 362 HOUSING 3 3 8 X 2 CARRIAGE BOLT 12 3 8 LOCKWAS
4. ASHER OPERATION DECAL BLADE DECAL BELT DECAL QUANTITY N IN NN N N ADJUSTING DECK GAUGE WHEELS REAR ROLLERS AND CHAIN HANGERS THE CUTTING HEIGHT OF THE MOWER IS DETERMINED BY THE POSITION OF THE GAUGE WHEELS AND THE REAR ROLLER BRACKET ON THE MOWER DECK THE MOWER DECK IS FULL FLOATING TYPE AND WILL CLOSELY FOLLOW THE CONTOURS OF THE GROUND WHEN USING THE GAUGE WHEELS AND REAR ROLLERS FOR THE HEIGHT OF VARIOUS CUTTING POSITIONS ADJUSTMENT IS DONE BY REMOVING THE GAUGE PIN AND CLIP MOVING THE STEM OF THE FRONT FORK OR REAR ROLLER BRACKET UP OR DOWN TO THE DESIRED HEIGHT BE SURE TO HAVE ALL FOUR STEMS IN THE SAME ADJUSTMENT ON THE MODELS 60 AND 72 DECKS THERE IS CARRIER STRAP LOCATED AT THE REAR OF THE DECK IT IS VERY IMPORTANT TO ADJUST THE STRAP AT THE SAME TIME THE FRONT CASTOR WHEEL FORK IS ADJUSTED KEEP THE REAR ROLLERS APPROXIMATELY 1 8 TO 1 4 ABOVE THE GROUND BY PLACING THE PIN ON THE PUSHARM INTO THE PROPER HOLE ON THE CARRIER STRAP IN ORDER TO RAISE OR LOWER THE REAR OF THE DECK TO ATTAIN THE DESIRED RESULT THE OPTIMUM SETTING IS WHERE THE REAR OF THE DECK IS JUST SLIGHTLY HIGHER THAN THE FRONT OF THE DECK THIS WAY THE BLADE HAS TO CUT THE GRASS ONLY ONCE BELT ADJUSTMENT INSTRUCTIONS YOUR MOWER WILL SHIP TO YOU ADJUSTED TO THE FIRST HOLE AS SHOWN AFTER 1 HOURS OPERATION CHECK THE BELT TENSION THE SPRING TENSION SHOULD BE ADJUSTED SO THAT THE SPRING IS EXTENDED ONE INCH
5. DEINES MANUFACTURING CORPORATION PARTS AND DECK MAINTENANCE FOR ALL MODELS AREA OF MAINTENANCE Gearbox Superior Blade Spindle Housing Castor Wheel Forks Castor Wheel Stem the pneumatic tire Castor Wheel Fork amp Stem Adjustment HOURS 40 NOTES Check lubricant every 8 hours A vented dipstick plug is located on the top of the gearbox The oil level should be at the fill line on the dipstick tube If the oil level is low add 80w90 gear oil CAUTION DO NOT OVERFILL Tighten the dipstick finger tight Over tightening this dipstick will damage your gearbox housing Use one stroke of a lubricator with multipurpose grease This prevents moisture from accumulating in the housing Use two strokes of lubricator with multi purpose grease Use three strokes of a lubricator with multi purpose grease Check clip and pin to see that clip is secure to prevent fork or stem from falling out of the deck arm GEAR BOX PULLEY INSTALLATION AND REMOVAL TAPPED HOLE DRILLED HOLE TAPPED HOLE DRILLED HOLE TO INSTALL GEARBOX PULLEY ON GEARBOX SHAFT 1 Align drilled holes in bushing flange with tapped holes in sheave hub 2 Insert capscrews through drilled holes in bushing flange and thread loosely in tapped holes in the sheave 3 Position the assembly on the shaft and tighten the capscrews progressively and uniformly 4 Torque specifications for a 1 4 20 grade 5 bolt is a maximum of 8 foot
6. HER 12 3 8 FLATWASHER 12 6 400 366 SPACER 3 7 400 257 SNAP RING 3 8 300 745 SADDLE 3 3 8 X 1 1 4 HHCS 6 3 8 LOCKWASHER 6 3 8 NUT 6 9 300 261R BLADE 3 300 468 3 8 X 1 1 4 HHCS 6 10 300 466 3 8 X 1 NF HHCS 3 3 8 LOCKWASHER 3 11 400 324 KEY 3 12 300 212A GREASE FITTING 3 13 300 466 3 8 X 1 NF HHCS 3 3 8 LOCKWASHER 3 14 300 284 KEYSTOCK 3 15 300 607 SHIELD 3 16 300 278 WASHER 6 REF NO GQ N SUPERIOR GEARBOX PARTS EXPLOSION MODEL R100 9AAC A0485 PART NO DESCRIPTION REQ D R100 8B00 A0500 PINION SHAFT WITH GEAR 1 R100 8B00 A0502 CROSSHAFT WITH GEAR 1 R100 003M A0427 CASTING WITH TAPPED HOLES 1 R100 004M A0503 CASTING WITH THRU HOLES 1 300 227A BEARING CUP 4 300 227 BEARING CONE 4 203293 RETAINING RING 1 200300 PIPE PLUG 4 109843 SEAL 4 IP3021 DIPSTICK 1 103125 SOCKET HEAD CAP SCREW 8 USE 80W90 MULITPURPOSE OIL IN THE SUPERIOR GEARBOX USE THE DIPSTICK TO DETERMINE OIL FILL LEVEL 60 DECK ASSEMBLY 10 42 43 42 44 5 24 25 300 715 300 262 300 455 100 320 300 509 400 288 300 655 300 289 400 178 400 951 300 712 300 709 300 716 300 518 300 517 300 525 300 740 300 511 400 121 300 704 300 704 300 706 300 705 300 710 300 701 100 335 300 203 300 202 300 331 300 703 400 998 60 DECK ASSEMBLY DESCRIPTION QUANTITY BELT WASHER FENDER NUT RH SKID 5 16
7. ING WARRANTIES OF ABOVE AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS SHALL APPLY AFTER SAID APPLICABLE PERIOD HAS EXPIRED DEINES SHALL UNDER NO CIRCUMSTANCES BE LIABLE FOR ANY DIRECT INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES AND OR EXPENSES The sale of this product is not subject to any implied warranties of merchantability and there are no warranties which extend beyond the description of the face hereof This warranty gives you specific legal rights You also have implied warranty rights In the event of problem with this warranty service or performance you may be able to go to small claims court State Court Federal District Court
8. ollows one year for Industrial and or Commercial applications one year for Residential applications THIS WARRANTY WILL NOT TAKE EFFECT unless the Warranty Registration Card is signed and returned to the Deines Manufacturing Corp with in ten days from delivery date This warranty is void if the component or product is modified in any manner which Deines concludes after inspection adversely affects the reliability of the component or product if the component or product has been repaired or serviced by anyone other than an Authorized Distributor or Dealer or the Deines Plant if the component or product is damaged because not operated in accordance with application with applicable instructions or because of accident misuse or abuse if the component or product is damaged because not properly maintained as set forth in applicable instructions This EXPRESS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES Deines neither assumes nor authorizes any other person natural or corporate to assume for it any other obligations or liability in connection with or with respect to any component or product EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ALL IMPLIED WARRANTIES MADE BY DEINES IN CONNECTION WITH ANY COMPONENT OR PRODUCT MANUFACTURED BY IT INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE WARRANTY PERIODS SET FORTH IN PARAGRAPH FORTH ABOVE AND NO WARRANTIES EXPRESS OR IMPLIED INCLUD
9. pounds Do not over torque TO REMOVE 1 Remove capscrews and thread in tapped holes in bushing flange Tighten progressively until bushing is free from sheave taper 2 Remove assembly from shaft 3 Do not use a puller on this type of sheave SPINDLE ASSEMBLY INSTRUCTIONS SNAP RING STEP 1 STEP 2 STEP 3 BEARING SRG STEP 4 STEP 5 STEP 6 7 8 9 PRIOR TO SERIAL Y1909 Place bottom bearing in housing and secure with snap ring Assemble shaft blade saddle woodruff key blade lock washer and bolt Tighten bolt and draw shaft into bottom of the blade saddle Place trash shield and machine bushing over shaft and against blade saddle Slide the above shaft assembly in bearing that is in the hub Slide spacer over the shaft and press the bearing into top side of the hub Again be sure to place hub of bearing toward center of the hub Place machine bushing on shaft and against the bearing Slide the pulley onto the shaft using the square key With bolt nut and washer secure the pulley to the shaft and clamp the rotating assembly together Install set screws in pulley using locktite Install bolts lock washers and nuts on the two remaining holes in the blade 60 SPINDLE ASSEMBLY INSTRUCTIONS AFTER SERIAL Y1909 FAN TORQUE TO 90 a 5 8 LOCK WASHER PRESS
Download Pdf Manuals
Related Search