Home
Chapter 1: Introduction and Tools
Contents
1. Gerber CAT UV Ink Jet Printer In consideration of the furnishing of the information contained in this document the party to whom it is given assumes its custody and control and agrees to the following The information herein contained is given in confidence and any part thereof shall not be copied or reproduced without written consent of Gerber Scientific International Inc This document or the contents herein under no circumstances shall be used in the manufacture or reproduction of the article shown and the delivery of this document shall not constitute any right or license to do so Information in this document is subject to change without notice Printed in USA Gerber CAT UV GerberCAT Cold Fire Cure Technology FastFacts ImageRIP OMEGA Support First and Matched Technology System are trademarks and GSP is a registered trademark of Gerber Scientific Products Mistral is a trademark of Spandex Onyx and PosterShop are registered trademarks and ProductionHouse is a trademark of Onyx Graphics Adobe Adobe Illustrator Adobe Photoshop Adobe Acrobat and Adobe Reader are registered trademarks of Adobe Systems Inc X ACTO is a registered trademark of Hunt Corporation Microsoft Windows and Windows XP are registered trademarks of Microsoft in the USA and other countries Wasatch SoftRIP is a registered trademark of Wasatch Computer Technology SignLab is a trademark of CADlink Technology Flexi and PhotoPrint are trademarks of SA Inter
2. also requires a high skill level in mechanical and electromechanical assembly Incorrect assembly or adjustment can seriously reduce printer output quality General tools General hand tools are used to remove adjust and reinstall a variety of Gerber CAT UV parts including covers circuit boards and mechanical components 4 Long handled T wrench hex drivers 5mm 4mm 3mm 2 5mm 2mm 1 5mm Long handled ball end hex drivers 5mm 4mm 3mm 2 5mm 2mm 1 5mm Long short handled Allen wrenches 3mm 2 5mm 2mm 1 5mm Screwdrivers Assorted Phillips head and flat head Adjustable wrench Needle nose pliers Wire cutters Hook tool Dental hook pick Electric Multi meter Electric grounding strap 10x magnifier or loupe to use for calibration and a blue light to align yellow Razor blade or non metallic abrasive pad P83214A Rev 1 Gerber CAT UV Chapter 1 1 11 Introduction and Tools Special Tools The following tools are required to install calibrate and perform certain repairs on the Gerber CAT UV P82195A Gantry Installation Cones 1 Set P82196A Gantry Installation Shafts 1 Set P82470A Way Support tool 1 Set T82201A Roll to Roll Hub Gap Spacer 1 T82202A X axis Belt Tensioning Gauge T82997A Steel Belt X axis Tensioning Gauge amp Gimbal T82203A Carriage Maintenance Stand T82208A Head Height Block 2 8mm T82209A Head Height Block 31 75mm P82560A Y Encoder tool Kit T82573A Y Ax
3. 14A Rev 1 Gerber CAT UV Chapter 1 1 7 Introduction and Tools Electrical WARNING Observe these safety precautions to avoid possible electrical shock hazard when using the Gerber CAT UV se the correct power cord do not use a damaged power cord Turn printer off and unplug it from the power source before servicing U Use an outlet with a ground terminal or electric shock can occur U nplug any communications cables before servicing Never open covers affixed by screws unless directed by Gerber service personnel Doing so may result in electric shock or damage to the printer Remove any electrostatic charge from your clothing or body by touching a metal part of the printer before servicing Electronic components such as memory may malfunction if exposed to electrostatic charge Industrial rubber mats are required under and around the printer if it is installed on carpeting Ink handling and disposal AN CAUTION Observe these general safety precautions when operating the Gerber CAT UV Ink Jet Printer Do not use inks other than GerberCAT inks Using other inks will void the warranty and will damage the printer Consult the Gerber CAT ink MSDS for proper handling disposal and safety recommendations Also consult local laws and regulations Do not open ink pouches Ink could get on your skin or in your eyes When handling ink pouches and waste ink be careful that the ink does not get on your skin If it
4. Chapter 1 Introduction and Tools Copyright Notice sini ee erdekeset aeeie denedi niet rapia siensa aeaeaei Lis ibsceobabessar bles estab ibas 2 FCC Compliance ii cis setae E dot E E E AB E da AD 3 Notes before Servicing ssepe e E AR EES EE EAEE E ESO ER EEEO EERE EER 4 Conventions and Symbols e ae e aae E a a E EE EAA A E EREE 4 PrnterorientaHion siea aae SEE Aes E E E E E Ee REES AES 5 Safety Info ION aiie Tesseire seere en iio Eeoa ASt En oeae colas epsabesecnsnsnsecdandecengaetesedekuteeesadeonedar scene 6 Emergency SLOP ues ee i eieae et Eroa E aea Esae N a aa Er aa RE Rae EAE ER EAEE ESEE 6 A EE EA E A A A A T 7 Ink handling and disposals teis ianh a ee ea aR a eraasi e vi Printer VENTO 0 A Ad E ii 7 Personal precautionS eiaiioriooncaroci nrinsnonacenear gnsaconiennanoanidrdasan one ATRE Res SER Ruhe cdbatdenceonsenseabesenseosebenendededenes 8 UV lamp precautions Sono e rna E aaa EE EE nana ro nannnnnnnnnnenananannn nn TETEN EAEE E E a TAT 8 Technical Support peiie eiee ieee eea eara aaa AEE ia e leaned aE aE EEAS KEE Eeo E AE econ 9 Toolsand S ppheS USAS 10 General tool cian ia del S SEER 10 Special Lodi SAI OA DD 11 Gerber CAT UV Chapter 1 1 2 Introduction and Tools Copyright Notice COPYRIGHTO 2010 Gerber Scientific International Inc All Rights Reserved This document may not be reproduced by any means in whole or in part without written permission of the copyright owner This document is furnished to support the
5. does wash your skin with soap and water Seek medical attention if irritation persists If your clothing comes in contact with uncured ink remove any contaminated clothing and wash them separately with soap and water If ink gets in your eyes immediately rinse your eyes with copious amounts of water for at least 15 minutes and seek medical attention immediately Dispose empty ink pouches waste ink lint free wipes and used swabs according to local laws and regulations Printer ventilation AN CAUTION Observe these general safety precautions when operating the Gerber CAT UV Ink Jet Printer P83214A Rev 1 Gerber CAT UV Chapter 1 1 8 Introduction and Tools Do not obstruct printer exhaust fans Printer should run with all covers attached to insure proper air flow inside the machine Personal precautions AN CAUTION Observe these general safety precautions when operating the Gerber CAT UV Ink Jet Printer There are two emergency stop switches located on either end of the gantry Press either switch to immediately shut down the UV lamps and abort printing Be careful when reaching into the printer to open the maintenance shelf or swab the print head The UV lamp assemblies and interior surfaces of the printer may be hot Be careful not to pinch fingers in drawers pinch wheels and material feed system Use caution when lifting heavy rolls or pieces of material UV lamp precautions UV WARNING Exposu
6. is Belt Height T82183A Variable Temperature Heat Gun 120 Volts P82493A Nozzle Kit Heat Gun P83067A Side Plate Park Gap Jacks T82573A Carriage Shield Gap Go NoGo T82830A Data Logger Temp Humidity T82828A CSK 3 Flute 1 4 Bit T82829A Deburring Tool T82832A Drill Bit 3 16 hip CC pa pap pa a pap apa jp P83214A Rev 1
7. national Inc P83214A Rev 1 Gerber CAT UV Chapter 1 1 3 Introduction and Tools FCC Compliance Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at own expense This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada P83214A Rev 1 Gerber CAT UV Chapter 1 1 4 Introduction and Tools Notes before servicing This manual covers service information for the Gerber CAT UV ink jet printer Only qualified technical personnel with the correct tools should perform service and repair actions Before performing any service keep in mind the following points 4 4 4 Read all directions com
8. pletely BEFORE performing any service procedures Read and comply with all safety instructions before performing service Note all cable markings and connector cable orientation BEFORE disconnecting any wiring Observe preliminary steps for any service actions Many components are located under panels Some disassembly is required to access parts and mounting hardware When reassembling observe all torque and tension requirements Use properly calibrated tools to perform actions that specify values for torque tension and force Some service actions require additional adjustment calibration or alignment AFTER a part is replaced If you experience any difficulties in performing service actions or if you find an error in a procedure contact Gerber Field Service Conventions and symbols The following conventions are used in this service manual could result in electrical shock hazard WARNING A warning statement contains information which if not followed CAUTION A caution statement contains information which if not followed could result in personal injury or equipment damage TIP A tip contains a suggestion to make your task easier or to remind you of something that No NOTE A note contains important information that affects the successful completion of a task may appear elsewhere in the booklet P83214A Rev 1 Gerber CAT UV Chapter 1 1 5 Introduction and Tools Printer orientation Make note of the orienta
9. re to UV light can be dangerous to eyes and skin and should be avoided Never operate the Gerber CAT UV with any of the covers removed Never operate the printer with the rubber light shields flaps missing or damaged Contact Gerber if any of the rubber light shields flaps need to be replaced P83214A Rev 1 Gerber CAT UV Chapter 1 1 9 Introduction and Tools Technical Support If you have questions regarding using maintaining or troubleshooting the Gerber CAT UV please contact Gerber Field Service EN phone 800 828 5406 860 644 1551 ext 8602 fax 860 871 3862 DX e mail gspservice gspinc com A www gspinc com a A FastFacts Gerber FastFacts provide answers to technical and service questions FastFacts are available on the Gerber web site under Support GERBERnet Online resource for the latest documentation service notes and firmware downloads A password is required for access to service level items Follow the link on the Gerber web site under Support gt How to use GERBERnet 1 Got to the Gerber Scientific Products website www gspinc com 2 At the bottom of the website click GERBERnet to open the Gerber Scientific Products login page 3 Customer user name and password are on the top right side of the page P83214A Rev 1 Gerber CAT UV Chapter 1 Introduction and Tools Tools and supplies 1 10 CAUTION Do not service the Gerber CAT UV without the correct tools Service
10. tion of the printer The flatbed table end with the maintenance shelf is considered the front of the printer and the control panel end of the gantry is the left side Also note that the right and left sides of the graphic file sent from the RIP software are reversed FRONT pa Maintenance shelf TOP Orientation of graphic sent from RIP E 7 software F CENTER G T H T BOTTOM HT Control panel RIGHT m LEFT Roll to Roll BACK P83214A Rev 1 Gerber CAT UV Chapter 1 1 6 Introduction and Tools Safety information Emergency Stop There are two emergency stop buttons located on either end of the gantry Press either button to immediately shut down the UV lamps and abort printing Emergency Stop Switches The screen flashes the following Emergency Stop message Emergency Stop Opening the maintenance shelf or the head access door will also cancel a job which is printing or paused Use care when accessing either of these areas When any of these actions causes an emergency stop a message displays asking the operator to Check the Shelf Access Door or E Stops Check the Shelf Access Door or Press ENTER when done cf Once the operator has corrected the condition and pressed ENTER the motors of the printer perform a homing sequence Y Note If the power is restored or the condition corrected before the Check Shelf Access Door or E Stop message displays the printer displays a Motor Power Cycled message P832
Download Pdf Manuals
Related Search
Related Contents
ペンダント発信器 セット Tek-ENTRY® Telephone Entry System Krown Manufacturing WakeMEup User's Manual Corel WordPerfect Office X3 Digisystem Microphone DM10 SDI-MV Multiviewer User Manual CARPOD INSTweb - 3WM Office Supplies Please Copyright © All rights reserved.
Failed to retrieve file