SERVICE MANUAL Refrigerator
Contents
1. lt LIEGE 6 143 7710152 00_11 PRINTED 2010 5 Trouble Shooting 4 1 MODEL HR 933F BANGLADESH Part Name Check Method and Criterion Measure the resistance with a tester Ambient temperature Room temperature 25 eC gt C BZN176 L2Z Open 0 2 or Short Circuited Measure the resistance with a tester Compressor Ambient temperature Room temperature 25 we Measure the resistance with a tester Starting Relay Ambient temperature Room temperature 25 4TM427RHBYY 53 Less than 1 Approx Open 90 2 or Short Circuited 002 Measure the resistance with a tester Overload Protector Ambient temperature Room temperature 25 Short Circuited m Starting Capacitor PRINTED Jun 2010 REF NO 7710152 00_11 6 Replacement of Parts Unplug the power cord before servicing 1 Model HR 933F Part Name Operating Procedure Thermostat 3 Remove Freezer Corner 7 Lift FF Cover 9 Release Thermostat s lock i Ew B ix 4 ar i 4 m PRINTED 2010 REF NO 5 7710152 00 11 7 10 Pull out Thermostat from Plate MTG 11 Pull out electrical wire from 12 After replacing Thermostat reverse Motor Thermostat by gripping the plug the steps abo2. from Evaporator tube tube 4 After replacing Bimetal Thermo Thermal Fuse reverse the steps above PRINTED 2010 REF NO 5 7710152 00 11 Page 11 Part Name Operating Procedure Damper Thermostat 2 Release Door 3 Remove all Glass Shelf 4 Remove Shield Light from Cover 5 Turn Knob Thermostat to Min 6 Pull out Knob Thermostat from Cover Thermostat position Thermostat 7 Dig Cover Cap out PRINTED 2010 REF NO 5 7710152 00 11 12 10 Separate Insulation from Cover Remove paper tape from Insulation 12 Straighten Damper Thermostat Thermostat sensing tube 14 Release screws that hold Damper 15 Pull Damper Thermostat from Case Thermostat and Case Damper Damper 11 Part Name Operating Procedure Lamp Follow step 1 3 of replacing Damper Thermostat 1 Remove Shield Light from Cover 2 Turn Lamp counterclockwise to 3 After replacing Lamp reverse the Thermostat remove steps above P PRINTED 2010 REF NO 5 7710152 00 11 13 Part Name Operating Procedure Door Switch Dig door switch out 2 Pull door switch from Inner Box 3 Hold recept terminal 4 After replacing Door Switch reverse the steps above PRINTED Jun 2010 REF NO 5 7710152 00 11 Part Name Defrost Timer Case PRINTED 2010 Operating Procedure 1 Release screws th
3. Haier SERVICE MANUAL Refrigerator FOR EXPORT 2010 Specifications 1 1 Specific parts for specific countries Item Power Source Internal Volume Litre Model Destination Power Cord Voltage ac Hz by ISO 8561 1995 O HR 933F VENEZUELA VE 115 60 J2 USA Style 332 N PRINTED Jun 2010 REF NO 7710152 00_11 2 1 2 Product Model HR 933F Defrost System Automatic Rigid Polyurethane Foam Cyclopentane Insulation Rigid Polyurethane Foam Cyclopentane Rigid Polyurethane Foam Cyclopentane 1 3 Characteristic of Thermostat Operating Temperature C 1013hPa mb Dial Position Temperature a 1 gt Control NORMAL a xi dao 24 5 1 5 1 4 Electrical Parts 1 4 1 MODEL HR 933F Compressor Power Supply Range 115 127V 50 60 Hz Starting Relay MTRP4615 Overload Protector ATM427RHBYY 53 Starting Capacitor 160 VAC Interior Light 240 15 W PRINTED Jun 2010 REF NO 5 7710152 00 11 3 Wiring Diagram POWER CORD OVER LOAD PROTECTOR R DOOR SWITCH x 4 4 or A 2 O STARTING RELAY STARTING CAPACITOR GROUND MULLION HEATER PRINTED Jun 2010 REF NO 7710152 00_11 4 Refrigerant Circuit 3 Somme CONDENSER PIPE SUCTION TUBE ASS Y CONDENSER PLATE COMPRESSOR TUBE CHARGE d LL 2 2 21512 ESTE
4. at hold Electric 2 Open the Electric Case Cover as the 4 Hold Recept Terminal then pull out electrical wires from Defrost Timer Page 14 3 Release screws that hold Defrost Timer from the Electric Case Cover 5 After Replacing Defrost Timer reverse the steps above REF NO 5 7710152 00 11 15 Part Operating Procedure Starting Relay 3 Lever Starting Relay by flatton screw driver 5 After Replacing Starting Relay reverse the steps above 4 Hold Recept Terminal then pull out electrical wires from Starting Relay PRINTED Jun 2010 REF NO 5 7710152 00 11 16 Part Name Operating Procedure Overload Protector Follow step 1 3 of replacing Starting Relay 1 Remove Overload Protector 2 Remove Overload Protector 3 Hold Recept Terminal then pull out electrical wires from Overload Protector 4 After Replacing Overload Protector reverse the steps above PRINTED Jun 2010 REF NO 5 7710152 00 11
5. ve Part Name Operating Procedure Fan Follow step 1 8 of replacing Thermostat z 1 EET 2 1 Dig Spring 3 After replacing Fan reverse the steps 2 Pull out Fan from Fan Motor above PRINTED 2010 REF NO 5 7710152 00 11 8 Part Name Operating Procedure Fan Motor Follow step 1 9 of replacing Thermostat Follow step 1 2 of replacing Fan 1 Press Plate MIG Motor to 2 Lift Plate Motor out 3 Release screw at Cover A remove lock L 4 Pull Cover A from Plate Motor 6 Hold Recept Terminal then pull out electrical wire from Fan Motor PRINTED Jun 2010 REF NO 5 7710152 00 11 9 Part Name Operating Procedure Glass Tube Heater Follow step 1 8 of replacing Thermostat 3 Press Plate MTG Motor Ass y to remove lock M 5 Take out socket of Glass Tube Heater 7 Remove aluminium tape that cover 8 Hold Glass Tube Heater at the rubber 9 After replacing Glass Tube Heater electrical wire connector reverse the steps above PRINTED 2010 REF NO 5 7710152 00 11 Part Name Bimetal Thermo amp Thermal Fuse 1 Take out socket of Bimetal Thermo amp Thermal Fuse 30 10 Operating Procedure Follow step 1 8 of replacing Fan Motor Follow step 1 6 of replacing Glass Tube Heater 2 Cut out Cable Tie from Evaporator 3 Cut out Cable Tie
Download Pdf Manuals
Related Search