"service manual"
Contents
1. Operation How to Control Pan and Tilt Move joystick left right and up down Scanning Stop Scan Preset 96 Random Scan Preset 97 Frame Scan Preset 98 Auto Scan Preset 99 Zoom Far To zoom far do the following 1 Press the Zoom Tele button or turn the joystick clockwise until you have the picture you want or you reach the optical zoom limit 2 Release the button or joystick 3 To continue zooming digitally immediately press the button or turn the joystick clockwise again until you have the picture you want or you reach the digital zoom limit Zoom Wide Press the Zoom Wide button or turn the joystick counterclockwise Presets Refer to the documentation supplied with the controller Patterns Refer to the documentation supplied with the controller Zones Refer to the Programming section and to the documentation supplied with the controller Alarms Refer to Alarms in the Operating Notes and in the Programming section Auto Flip Turn on or off in the programming menu Refer to the Programming Guide in the Programming section Optical zoom magnifies the image and the picture remains clear Resolution is constant Digital zoom magnifies the image and the picture may appear pixilated The larger the zoom limit the greater the reduction in resolution 3 The dome cannot do electronic zoom in a pattern Optical zoom will operate in a pattern For more information refer to Operating Notes Pelco Manual C2423M 5 002. 1 Program preset 95 28 The main menu appears 2 Position the cursor gt beside Alarms Zone Blank 3 Press the Iris Open button to enter the Alarms Zone Blank menu 4 Position the cursor gt beside Zone Blank 5 Press the Iris Open button to enter the Zone Blank menu 6 Position the cursor gt beside the number of the zone for which you want to set the blank option 7 Pressthe lris Open button The cursor moves to the right beside the word On or Off 8 Move the joystick up or down to toggle between the words On and Off 9 SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting ZOOM LIMIT Main Menu Camera Menu Camera Backlight comp Off Line Sync Zoom limit x72 lt Power Up gt Reset camera lt AUX gt lt Gain AGC gt lt Alarms Zone Blank gt lt AUto iris gt lt Other gt lt Next gt EXIT Exit The Spectra Il is a 72X zoom camera 18X optical zoom and 4X electronic zoom can be set for 18X 36X 54X or 72X To change the zoom limit NOaRON gt Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the cursor gt beside Zoom Limit Press the Iris Open button The cursor moves to the right beside the current zoom limit Move the joystick up or down to choose the z
3. OPERATING NOTES PAN AND TILT FUNCTIONS Preset Mode 250 per second Controller Type Pan Tilt Fixed speed Speed determined by controller Speed determined by controller Variable speed 0 1 to 80 per second depending on joystick position 0 1 to 40 per second depending on joystick position Turbo Mode 150 per second 200 per second Does not affect the tilt speed NOTE For American Dynamics controllers with only 32 presets set switch SW1 7 on the dome drive in the ON position When SW1 7 is ON preset 99 becomes 32 98 becomes 31 97 becomes 30 96 becomes 29 95 becomes 28 93 becomes 26 92 becomes 25 91 becomes 24 90 becomes 23 89 becomes 22 88 becomes 21 If the limit stops are turned off refer to the Limit Stops section presets 23 26 can be used as regular presets Pelco Manual C2423M 5 00 If the proportional pan mode is enabled refer to Proportional Pan in the Programming sec tion the pan and tilt speeds will depend on the amount of zoom At telephoto zoom set tings the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings This keeps the image from moving too fast on the monitor when there is a large amount of zoom This slowing does not happen when going to a preset but does occur in turbo mode when high zoom is selected The minimum pan and tilt speeds are 0 1 degree per second at full zoom AUTO FLIP When the camera til
4. Slow shutter operation affects the auto IR level setting If slow shutter is set for manual operation only two settings for the IR level are available Dusk and 2 If slow shutter is set for automatic operation all four IR level settings are available If the IR level is set at 3 or Dark and the slow shutter is turned off the IR level will auto matically reset to 2 To program the slow shutter mode refer to the Slow Shutter Mode section To change the auto IR level settings 1 Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the cursor beside Next Press the Iris Open button to enter the Next menu Position the cursor gt beside IR Filter Press the Iris Open button to enter the IR Filter menu Position the cursor gt beside Auto IR level Press the Iris Open button The cursor moves to the right Move the joystick up or down to toggle between the four level settings SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting zo OOO XOT dec eos I a ch AUX MODE Main Menu Aux Menu Camera Line Sync Power Up Aux Alarms Zone Blank Other EXIT Aux 1 mode Normal Aux 2 mode Normal Exit There are three settings for AUX mode Normal Controller operate
5. PELLO SD5BCBW Series Spectra II Color Black amp White Dome Systems Operation and Programming Manual C2423M 5 00 Pelco 3500 Pelco Way Clovis CA 93612 5699 USA Pelco Online www pelco com In North America and Canada Tel 800 289 9100 FAX 800 289 9150 DataFAX 800 289 9108 International Customers Tel 1 559 292 1981 FAX 1 559 348 1120 DataFAX 1 559 292 0435 PelcoEurope BV Dillenburg Center Dillenburgstraat 5F 5652 AM Eindhoven The Netherlands Tel 31 40 251 9870 FAX 31 40 251 9835 CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS in 3 OPERATION e PROGRAMMING 2 neret etate ott retire o I anne POWER UP DISPLAY EE 4 OPERATING YOUR SPECTRA II COLOR BLACK amp WHITE DOME wd OPERATING NOTES tienen ere terere ped d dde he ha eet 5 PAN AND TILT FUNCTIONS iii 5 AUTO FLIP 5 SCAN SPEED intente eo Pa eben a d decederet tas ts PRESET F NGTIONS 5 teer aii eee de i ep me i ee ri ad RANDOM FRAME AND AUTO SCANNING ALARMS tritt ptt ea mee tote te t see kde e era dns ee he e Ee AUXILIARY OUTPUTS IR FILTER ne irte eerte t ere ee tete ete nire te e eos AUTO IRIS PROGRAMMING GUIDE SPECTRA Il COLOR BLACK amp WHITE ACCESSING MAIN MENU PRESET 95 ALARMS deett is ALARM DWELL seseesseeeenenennen enn een nennen nnne nennen nnne inneren ALARM PATTERN i e dei ESA ALARM PRIORITY ALAR
6. If Auto White Balance is on it changes to off when you select a new value ZONES The Spectra Il dome is capable of eight zones each with a 20 character label Depending on the controller you can define the zone size and define any zone as blanked for video when the camera pans into the zone area Zones can be programmed to overlap each other although this is not recommended If you program two zones to overlap the title of the zone with the highest priority zone 8 is the hiest zone 1 is the lowest will be displayed in the overlap area The same applies to zone blanking For other information on programming zones refer to the documentation for your control system Pelco Manual C2423M 5 00 25 NOTE The Spectra Il Color Black and White camera cannot do electronic zoom in a pattern Optical zoom will operate in a pattern 26 ZONE BLANK Main Menu Alarms Zone Blank Menu Zone Blank Menu Video Blank Zone 1Off 20ff ff p 30ff 40ff 5Off lt Camera gt Line Sync Power Up Alarm resume Alarm dwell sec SAXE lt Alarm priority gt lt Alarm pattern gt lt Zone blank gt lt Alarms Zone Blank gt 6Off 7Off 80f lt Other gt EXIT Exit This feature lets you define any of eight zones as blanked for video when the camera pans into the zone area There are two choices On Enables video blanking Off Disables video blanking To change the blank zone setting
7. If the camera resets it will only affect the line synchronization It will not change any other camera parameters such as auto focus or auto iris Press the Iris Close button if you do not want to change the setting Pelco Manual C2423M 5 00 LINE SYNC PHASE The cursor moves to a numeric value Move the joystick up or down to change the value Press the Iris Open button to select the choice The value represents the phase angle in tenths of a degree between 0 degrees and 359 degrees For example 900 is 90 degrees 1200 is 120 degrees and 2400 is 240 degrees Press the Iris Open button on your keyboard to select your choice The Line Sync setting will change to ON The camera may reset or the picture on your monitor may wiggle when you change the phase angle If the camera resets it will only affect the line synchronization It will not change any other camera parameters such as auto focus or auto iris Press the Iris Close button if you do not want to change the setting PARK TIME MINUTES NOTE Preset 1 must be programmed for the dome to park Main Menu Other Menu Camera Auto flip On Line Sync Proportional pan On Power Up Limit stops Off Aux Park time minutes 0 Alarms Zone Blank Scan speed deg s 25 Other Pattern length 1 5 min EXIT Exit This feature causes the dome to park at preset 1 after a programmed number of minutes of control inactivity The time can be set from 1
8. controllers 99 becomes 32 CM6700 98 becomes 31 1 Enter the number of the Spectra II or Spectra Lite camera and press the CAM key 97 becomes 30 2 Enter 95 and hold the PRESET key for two seconds 96 becomes 29 3 Inthe Edit Preset menu arrow to SET and press the ACK key The main menu appears e Ee 25 KBD200 KBD300 KBD300V Direct Mode Only 92 becomes 25 1 Enter 95 91 becomes 24 2 Hold the PRESET key approximately 5 seconds until the main menu appears on the 90 becomes 23 screen 89 becomes 22 88 becomes 21 CM8500 1 Enter the number of the Spectra Il or Spectra Lite camera and press the CAM key If the limit stops are turned 2 Highlight PRESET in the Camera menu and hold down the joystick button until the Set off refer to the Limit Stops Presets prompt appears 3 Enter 95 and press the PRESET key The text editor appears Select ENTER and the section presets 23 26 can main menu appears be used as regular presets CM9500 1 Enter the number of the Spectra Il or Spectra Lite camera and press the CAM key The Main menu appears 2 Highlight SETUP in the Main menu and press the SELECT key 3 Highlight CAM in the Setup menu and press the SELECT key 4 Highlight PRESET in the Camera menu and press the SELECT key 5 Enter 95 and press the F1 key The main menu appears CM9750 1 Turn the KEY SWITCH to the ON position 2 Press the PROG key PROGRAM appears on the LCD display 3 Press the PRES key Th
9. cursor gt beside Next Press the Iris Open button to enter the Next menu Position the cursor gt beside IR Filter Press the Iris Open button to enter the IR Filter menu Position the cursor gt beside IR Filter mode Press the Iris Open button The cursor moves to the right beside the word Auto or Off Move the joystick up or down to toggle between Auto and Off SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting If the IR filter is set to Auto check the AGC mode and shutter speed settings Both must be programmed for automatic operation for the IR filter to function automati cally Refer to the Gain AGC and Shutter Speed sections for programming information Rer Qi OOT E OTIO re a LIMIT STOPS Main Menu Other Menu lt Camera gt Auto flip On lt Line Sync gt Proportional pan On Power Up Limit stops Off Aux Park time minutes 0 Alarms Zone Blank Scan speed deg s 25 Other Pattern length 1 5 min EXIT Exit There are two types of limit stops Manual limit stops A manual joystick pan operation stops when a limit stop is reached Scan limit stops The dome reverses direction during random frame or auto scan ning when a limit stop is reached Limit stops are controlled by software To set limit stops 1 Turn on the limit stop mode 2 Program the
10. flip dis able limit stops zoom limit and proportional panning Turning off power to the Spectra Il dome does not reset the camera Camera settings are retained in memory When the power is turned back on the settings will be the same as they were when the power was turned off To reset the camera Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the cursor gt beside Reset Camera Press the Iris Open button to reset the camera Gi NES Pelco Manual C2423M 5 00 21 SCAN SPEED Main Menu Other Menu Camera Auto flip On Line Sync Proportional pan On lt Power Up gt Limit stops Off lt AUX gt Park time minutes 0 lt Alarms Zone Blank gt Scan speed deg s 25 lt Other gt Pattern length 1 5 min EXIT Exit The scan speed is adjustable from 1 40 degrees per second This occurs in three scan modes auto random and frame scan To change the scan speed Program preset 95 28 The main menu appears Position the cursor gt beside Other Press the Iris Open button to enter the Other menu Position the cursor gt beside Scan Speed deg s Press the Iris Open button The cursor moves to the right beside the number of degrees Move the joystick up or down to toggle through the number of degrees 1 40 until you reach the number you want If set on a low number the scan will appear
11. focus mode gt IR Filter gt lt Sharpness gt lt White balance gt Previous Auto white bal S Red bal level Aux lt Gain AGC gt lt Alarms Zone Blank gt lt Auto iris gt lt Other gt lt Next gt EXIT Exit Blue bal level Exit Exit The settings for white balance are as follows Auto white bal Red bal level Blue bal level To change the white balance settings Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the cursor gt beside Next Press the Iris Open button to go to the Next menu Position the cursor gt beside White Balance Press the Iris Open button The White Balance menu appears Position the cursor gt beside one of the following choices and press the Iris Open button O NOD O1 D gt AUTO WHITE BALANCE The cursor moves to one of two choices Auto or Off Move the joystick up or down to toggle between them Press the Iris Open button to select the choice or press the Iris Close button if you do not want to change the setting RED BALANCE and BLUE BALANCE LEVELS The cursor moves to a numeric value ranging from 0 through 255 Move the joystick up or down to a value As you change the value you can see the color change on your monitor Press the Iris Open button to select the value or press the Iris Close button if you do not want to change the setting
12. gain Off Mode In the off mode the AGC is off To change the AGC mode Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the cursor gt beside Gain AGC Press the Iris Open button to enter the Gain AGC menu Position the cursor beside AGC mode Press the Iris Open button The cursor moves to the right beside the word Auto or Off Move the joystick up or down to choose between Auto or Off SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the Iris Close button if you do not want to change the setting NN O1 8 D GAIN The gain adjusts the signal level of the video output Increasing the gain in low light condi tions will increase the level of noise in the picture To change the gain Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the cursor gt beside Gain AGC Press the Iris Open button to enter the Gain AGC menu Position the cursor beside Gain Press the Iris Open button The cursor moves to the right beside the current gain setting a numeric value Move the joystick up or down to change the gain As you change the gain the picture on your monitor gets brighter or darker 9 SELECT Press the Iris Open button on your keyboard to select y
13. la partie lectrique de ce produit une r sistance entre le courant et la partie expos e devrait tre install e afin de v rifier que la partie lectrique n aie pas t en contact d un court circuit 5 L installation entreprise et le mat riel utilis devraient supporter quatre fois le poids du boiti de la tourelle de la cam ra et de la lentille Ce produit et ou le manuel pourrait inclurent les symbols suivants Ce symbol indique qu un voltage dangereux pouvant provoquer un chock lectrique est pr sant dans cette unit RISQUE DE CHOQUE LECTRIQUE ue e NE PAS OUVRIR Ce symbol indique qu il y a des mesures d installation et d entretient importantes inclus dans le manuel de cet quipement Nous vous prions de bien vous familiarisez avec la manuel avant d entreprendre toute in stallation Pelco Manual C2423M 5 00 3 OPERATION POWER UP DISPLAY When the Spectra II dome is powered up the selected protocol revision number and other information is displayed on the monitor For example the screen might show the fol lowing information The information displayed depends on the selected pro tocol C D or P and the menu selection for power up mode Refer to the Power Up Mode in the Program ming section PELCO SPECT II 4 0 CONFIGURE DONE Protocol C The information remains on the monitor until the dome is moved OPERATING YOUR SPECTRA II COLOR BLACK amp WHITE DOME
14. position that corresponds to the alarm number For example if alarm 3 is activated the dome moves to preset 3 Runs a half pattern or full pattern as programmed in the Alarm Pattern menu If the activated alarm inputs have the same priority all low or all high then the dome will sequence between the presets that correspond to the alarm numbers If the activated alarm inputs have different priorities for example one is high and four are low the dome goes only to the high It remains fixed on the high and only goes to the low after the high has been cleared In certain situations the dome will respond as follows If a preset has not been set but an alarm is connected the dome will go to a factory preset that will not be the desired position If one alarm is a preset and another is a pattern and both are received the dome will alternate between them An alarm clears by returning to its former off state Depending on choices made on the programming menu the dome can respond to an alarm by running one of the patterns below Refer to Patterns in the Programming section for more information Run full pattern e Run half pattern 1 Run half pattern 2 When sequencing between presets the dwell time depends on the time set on the Alarm Dwell menu for that preset After the dwell time expires the dome immediately does one of the following If the resume feature was selected on the programming menu and there are n
15. the dome will go to preset 1 and park If the time specified is zero or if preset 1 has not been programmed the dome will not park The default is zero minutes IR FILTER The Spectra II color black and white dome has an IR infrared cut filter in the lens that switches in and out automatically or manually depending on how the dome is pro grammed Automatic operation is controlled by the Auto IR Level setting Manual operation is controlled by presets 88 filter IN and 89 filter OUT The dome also has two settings that enhance viewing in low light the Auto IR Level and Slow Shutter Mode The IR filter level is the light level at which the lens switches IN or OUT When the filter is IN the camera produces a color picture When the IR filter switches OUT the picture changes to black and white increasing visibility in low light conditions The slow shutter mode electronically extends the shutter time providing greater sensitivity in low light conditions The picture may appear rough or smeared depending on the dis tance and motion of the viewed image This feature operates with the IR filter IN or OUT LOW LIGHT does not mean NO LIGHT Some type of illumination is required street light IR light etc The camera is not sensitive to IR light when the IR cut filter is IN AUTO IRIS If auto iris is in the auto mode it remains that way until you manually open or close the iris The dome will return to auto iris whe
16. to 1 5 3 or 6 minutes The dome initiates the first half pattern when the power up sequence finishes The length can be set to 75 1 5 or 3 minutes The dome initiates the second half pattern when the power up sequence finishes The length can be set to 75 1 5 or 3 minutes The default setting is Default To select the power up mode Program preset 95 28 The main menu appears Position the cursor gt beside Power Up Mode Press the Iris Open button to enter the Power Up Mode menu Press the Iris Open button to move the cursor to the right Move the joystick up or down to cycle through the selections Stop on the item you Qr o c want to select SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting PROPORTIONAL PAN Main Menu Other Menu Camera Auto flip On Line Sync Proportional pan On Power Up Limit stops Off Aux Park time minutes 0 Alarms Zone Blank Scan speed deg s 25 Other Pattern length 1 5 min EXIT Exit There are two proportional pan modes On Enables the proportional pan mode The amount of zoom controls the pan and tilt At telephoto zoom settings the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings This keeps the image from moving too fast on the monitor when there is a large amount of zo
17. to barely move but is still functioning 7 SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting DARON SHARPNESS Main Menu Camera Menu Next Menu Sharpness Menu lt Camera gt lt Line Sync gt lt Power Up gt lt Aux gt lt Alarms Zone Blank gt lt Sharpness gt lt Other gt lt White balance gt EXIT Do the following to manually adjust the sharpness of the picture Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the cursor gt beside Next Press the Iris Open button to go to the Next menu Position the cursor gt beside Sharpness Press the Iris Open button The Sharpness menu opens Press the Iris Open button The cursor moves to the right beside the sharpness value Move the joystick up or down to toggle through available sharpness values As the numeric value changes the sharpness of the picture on the monitor changes SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the Iris Close button if you do not want to change the setting OOTO ORON E Em e Pelco Manual C2423M 5 00 SHUTTER SPEED Main Menu Camera Menu Next Menu Off Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto IR Filter lt Sharpne
18. Backlight comp Off Zoom limit x72 Reset camera lt Gain AGC gt lt Auto iris gt Next Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto IR Filter gt lt Sharpness gt lt White balance gt lt Other gt Previous EXIT Exit Exit Slow shutter mode slows the frame rate producing a digital color picture sensitive to low light conditions The picture may appear rough or smeared depending on the distance and motion of the viewed image There are two settings in the slow shutter mode Auto Slow shutter mode is enabled Off Slow shutter mode is disabled To change the slow shutter mode Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the cursor beside Next Press the Iris Open button to go to the Next menu Position the cursor beside Slow Shutter mode Press the Iris Open button The cursor moves to the right Move the joystick up or down to toggle between Auto and Off SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the Iris Close button if you do not want to change the mode 2X0 Qo X ta TO Pelco Manual C2423M 5 00 WHITE BALANCE Main Menu Camera Menu Next Menu White Balance Menu Camera Backlight comp Slow shutter mode Line Sync Zoom limit Power Up Reset camera Shutter speed Auto
19. If there is a bright light source outside of this area it will wash out to white The camera will ad just the iris so that the object in the sensitive area is properly exposed Off Backlight compensation is not activated To change the backlight compensation mode 1 Program preset 95 28 The main menu appears 2 Position the cursor gt beside Camera NON SENSITIVE AREA 3 Press the Iris Open button to enter the Camera menu SENSITIVE 4 Position the cursor gt beside Backlight Comp 5 Press the Iris Open button The cursor moves to the right beside the word On or Off 6 Move the joystick up or down to toggle between On and Off 7 SELECT Press the Iris Open button on your key board to select your choice CANCEL Press the Iris Close button if you do not want to change the setting amp n 0000000 Pelco Manual C2423M 5 00 15 16 GAIN AGC Main Menu Camera Menu Gain AGC Menu Camera Backlight comp Off Line Sync Zoom limit x72 lt Power Up gt Reset camera lt Aux gt lt Gain AGC gt lt Alarms Zone Blank gt lt Auto iris gt lt Other gt lt Next gt EXIT Exit Gain The amount of amplification the camera places on its video information in order to obtain a full 1 volt peak to peak video signal out AGC Automatic Gain Control AGC MODE There are two AGC settings Auto Mode Automatically adjusts the
20. M RESUME AUTO FLIP AUTO FOCUS MODE BACKLIGHT COMPENSATION GAIN AGC 0 0 eeeeeeeceeseeneeeeeeaeeeeecaeeeeeaesaeeeaecaeesaesaeeeesaeeeaesaeeaeesaeeeeeeaeseesaeseeeeaeeeeeeeeates ELE e KEE GAIN IR FILTER MODE LIMIT STOPS outers ke eve er i ihe ante nad ane ees nt t dee eet ple denne TURNING LIMIT STOPS ON OR OFF een 18 PROGRAMMING LIMIT STOPS Manual Limit StODS 5 cratere eee ee TA Scan Limit Stops opos tee Hep eee e I e ee Te LINE SYNCHRONIZATION PARK TIME MINUTES PATTERN LENGTH POWER UP MODE PROPORTIONAL PAN RESET GAMERA ivt nego n apt tete peace Dre eet tri d e HH t ade SCAN ES ad i DE SHARPNESS SHUTTER SPEED SLOW SHUTTER MODE ZONE BLANK aa an a tech hee ee SEA e ZOOM EIM ee eai E MAINTENANCE DOME CLEANING SERVICE MANUAL SPECIFICATIONS eese WARRANTY AND RETURN INFORMATION 28 Pelco Manual C2423M 5 00 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product the following WARNINGS should be observed 1 Installation and servicing should only be done by qualified service personnel and con form to all local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P en closure it is designed for indoor use only and it must not be installed where exposed to rain and moisture 3 Onl
21. No Pattern 3No Pattern 4No Pattern Camera Line Sync Power Up Aux Alarms Zone Blank A arem Other Exit EXIT Alarm resume Alarm dwell sec Alarm priority 5No Pattern 6No Pattern 7No Pattern You can choose one of the following for each of the seven alarm inputs Full Pat run full pattern Half Pat 2 run half pattern 2 Half Pat 1 run half pattern 1 No Pattern In response to an alarm the Spectra II dome can do either one full pattern 1 5 3 or 6 min utes long or two half patterns 75 1 5 or 3 minutes long To change the alarm pattern Program preset 95 28 The main menu appears Position the cursor beside Alarms Zone Blank Press the Iris Open button to enter the Alarms Zone Blank menu Position the cursor gt beside Alarm Pattern Press the Iris Open button to enter the Alarm Pattern menu GB ox Pelco Manual C2423M 5 00 NOTE The Spectra II Color Black and White camera cannot do electronic zoom in a pattern Optical zoom will operate in a pattern 6 Position the cursor gt beside the number of the alarm input for which you want to set the pattern 7 Pressthe lris Open button The cursor moves to the right beside the words Full Pat Half Pat 1 Half Pat 2 or No Pattern 8 Move the joystick up or down to toggle between the choices 9 SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press t
22. W PAL model DD5BCBW X Scanning System 2 1 interlace Image Sensor 1 4 inch interline transfer CCD 27 Effective Pixels NTSC 768 H x 494 V PAL 752 H x 582 V Horizontal Resolution 2470 TV lines Lens Minimum f stop F1 4 Focal Length 4 1 mm to 73 8 mm optical Zoom Ratio 18X optical zoom 4X electronic zoom Digital Slow Shutter Auto manual speed selection Horizontal Angle of View 48 at 4 1 mm wide zoom 2 7 at 73 8 mm telephoto zoom MTBF gt 500 000 cycles at room temperature zoom focus irs Focus Automatic and manual override Sensitivity 2 lux at 1 4 second shutter speed color 2 lux at 1 60 second shutter speed black amp white Sync System AC line lock phase adjustable via remote control White Balance Automatic with manual override Shutter Speed Automatic electronic iris manual NTSC 1 4 to 1 10 000 Color B amp W PAL 1 3 to 1 10 000 Iris Control Automatic with manual override Gain Control Automatic with manual override Video Output NTSC 714V 07V 100 IRE 10 IRE PAL 7V 07V Signal to Noise Ratio gt 46 dB Manual control of camera setup functions can be done with CM6700 CM8500 CM9500 CM9760 and MPT9500 controllers but not with CM7500 MPT9000 or KBD9000 controllers Design and product specifications subject to change without notice WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved
23. all alarms in the low setting Refer to the Alarm Priority section If presets 1 7 are not used for alarms they can be used as regular presets However if they are being used for alarms they should not be used for anything else Also refer to the Alarm Dwell Alarm Pattern Alarm Resume and Pattern Length sections to program alarm conditions ALARM DWELL Main Menu Alarms Zone Blank Menu Camera Line Sync Power Up Alarm resume Off Alarm dwell sec 5 Alarm priority Aux Alarm pattern Alarms Zone Blank Zone blank Other EXIT Sc This is the minimum time the Spectra Il will stay at an alarm even if the alarm is present for less than this amount of time To change the alarm dwell Program preset 95 28 The main menu appears Position the cursor gt beside Alarms Zone Blank Press the Iris Open button to enter the Alarms Zone Blank menu Position the cursor gt beside Alarm Dwell Sec Press the Iris Open button The cursor moves to the right beside the number of sec onds for the alarm dwell time 6 Move the joystick up or down and hold to cycle through 1 200 seconds in one second increments 7 SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the Iris Close button if you do not want to change the setting Qr o mc ALARM PATTERN Main Menu Alarms Zone Blank Menu Alarm Pattern Menu 1No Pattern 2
24. coated surface with direct hand pressure it will easily abrade unless extreme care is taken Once scratched the dome cannot be recoated 5 If internal wiping is necessary avoid hand rubbing Instead make a wick as follows Use a very soft paper towel Roll a section into a tightly wound tube Tear the tube in half and wet the fuzzy end of the wick with a solution of isopropyl alcohol diluted with water Hold the dome with its opening facing downward and wipe the interior of the dome with the wet end of the wick Use a circular motion starting from the outside and spiraling into the center Use a new wick for each two passes over the dome SERVICE MANUAL If you need to service your unit obtain a service manual in one of the following ways Go to Pelco s web site at ftp Awww pelco com and find service manual C1455SM B Contact Pelco s Literature Department and request service manual C1455SM B SPECIFICATIONS MECHANICAL Pan Movement 360 continuous pan rotation Vertical Tilt Unobstructed 2 to 92 Manual Pan Tilt Speeds Pan 0 1 80 sec manual operation 150 sec turbo Tilt 0 1 40 sec Preset Speeds Pan 250 sec Tilt 200 sec Pelco Manual C2423M 5 00 For variable speed operation an appropriate controller is required With fixed speed control lers pan tilt speed is 24 sec The CM6700 controller with the KBD200 keyboard has pro grammable fixed speeds CAMERA Signal Format NTSC model DD5BCB
25. d Latching Pressing the AUX key turns on the AUX and the next press of the AUX key turns it off Alarm Any alarm input activates the AUX Refer to your controller manual for operating instructions To change the AUX mode 1 Program preset 95 28 The main menu appears 2 Position the cursor gt beside AUX 3 Press the Iris Open button to enter the AUX menu Pelco Manual C2423M 5 00 NOTE If backlight compensation is ON and the IR cut filter switches OUT black and white mode in normal lighting condi tions adjust the Auto IR Level to a darker setting Refer to the Auto IR Level section 4 Move the joystick up or down to position the cursor next to either Aux 1 mode or Aux 2 mode 5 Press the Iris Open button The cursor moves to the right beside the word Normal Latching or Alarm 6 Move the joystick up or down to toggle between Normal Latching or Alarm 7 SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the Iris Close button if you do not want to change the setting BACKLIGHT COMPENSATION Main Menu Camera Menu Camera Backlight comp Off Line Sync Zoom limit x72 lt Power Up gt Reset camera lt Aux gt lt Gain AGC gt lt Alarms Zone Blank gt lt Auto iris gt lt Other gt lt Next gt EXIT Exit There are two backlight compensation modes On The dome uses the center 10 percent of the picture to adjust the iris
26. defective The above warranty provides the Dealer with specific legal rights The Dealer in material or workmanship for a period of one year after the date of shipment may also have additional rights which are subject to variation from state to state Exceptions to this warranty are as noted below If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 Three years on Genex Series multiplexers server and keyboard or 559 292 1981 to obtain a Repair Authorization number RA and provide Twoyears on cameras and all standard motorized or fixed focal length lenses the following information Two years on Legacy Camclosure Camera Systems CM6700 CM8500 CM9500 CM9750 CM9760 Matrix PelcoVision DF5 Series and DF8 Fixed 1 Model and serial number Dome products 2 Date of shipment P O number Sales Order number or Pelco invoice number Two years on Spectra and Esprit including when used in continuous 3 Details of the defect or problem motion applications Two years on WW5700 series window wiper excluding wiper blades If there is a dispute regarding the warranty of a product which does not fall Six months on all pan and tilts scanners or preset lenses used in continuous under the warranty conditions stated above please include a written explana motion applications that is preset scan tour and auto scan modes tion with the product when returned Pelco will warrant all replacement parts and repairs
27. e PRESET prompt appears 4 Enter 95 and press the ENTER key The main menu appears 5 Turn the KEY SWITCH to the OFF position CM9760 1 Press the ESCAPE key to open the Main menu Select DEF The Define Menu appears 2 Enter your four digit PIN if this is your first time entering this mode 3 Enter 95 and select PRST The main menu appears on the monitor 4 Select the Quit icon to return to the default menu KBD4000 KBD4002 KBD4000V 1 Press the SPOT MONITOR key 2 Enter 95 then hold the PRESET key approximately five seconds until the main menu appears on the screen MPT9500 Standard Coaxitron Mode 1 Enter 95 and press the PRESET SET key 2 Position the asterisk in the YES row and press the F1 key The main menu appears Extended Coaxitron or RS 485 Mode 1 Enter 95 and press the PRESET SET key 2 Press the F2 key The main menu appears Pelco Manual C2423M 5 00 9 NOTE Pattern length is set on the secondary menu entitled Other NOTE To make the pattern run to its end when an alarm activates it make alarm dwell time longer than pattern length Thus if the alarm goes away before the end of the pattern the pattern will continue until the dwell times out 10 ALARMS The Spectra Il dome has seven alarm inputs which can be designated as either high or low pri ority The high priority setting is significant when more than one alarm is activated If priority in alarms is not required leave
28. eo output as deter mined by the Level setting Off Auto iris is disabled and control is always manual Move the joystick up or down to toggle between Auto and Off Press the Iris Open button to select the choice or press the Iris Close button if you do not want to change the setting LEVEL The cursor moves to a numeric value which the dome uses to try to maintain a certain light level Changing the value of the Level setting will change the video level to which the auto iris adjusts This setting should be adjusted if the video level in the auto iris mode is too bright or too dark Move the joystick up or down to a value Press the Iris Open button to select the value or press the Iris Close button if you do not want to change the setting Pelco Manual C2423M 5 00 13 AUTO IR LEVEL Main Menu Camera Menu Next Menu IR Filter Menu Camera Backlight comp Slow shutter mode Line Sync Zoom limit Shutter speed Power Up Reset camera Auto focus mode IR Filter mode Aux lt Gain AGC gt IR Filter gt Auto IR Level lt Alarms Zone Blank gt lt Auto iris gt lt Sharpness gt lt Other gt Next gt lt White balance gt EXIT Exit The IR level setting determines when the IR filter will switch IN or OUT Following are the available settings for the Auto IR Level Dusk 1 60 second shutter speed 2 1 60 second shutter speed 3 1 30 second shutter speed Dark 1 15 second shutter speed
29. for 90 days from the date of Method of return shipment shall be the same or equal to the method by which Pelco shipment All goods requiring warranty repair shall be sent freight prepaid the item was received by Pelco to Pelco Clovis California Repairs made necessary by reason of misuse alter ation normal wear or accident are not covered under this warranty RETURNS In order to expedite parts returned to the factory for repair or credit please call co assumes no risk and shall be subject to no liability for damages or loss the factory at 800 289 9100 or 559 292 1981 to obtain an authorization num ulting from the specific use or application made of the Products Pelco s li ber CA number if returned for credit and RA number if returned for repair ility for any claim whether based on breach of contract negligence infringe Goods returned for repair or credit should be clearly identified with the assigned nt of any rights of any party or product liability relating to the Products shall CA RAnumber and freight should be prepaid All merchandise returned for credit exceed the price paid by the Dealer to Pelco for such Products In no event may be subject to a 20 restocking and refurbishing charge ill Pelco be liable for any special incidental or consequential damages includ loss of use loss of profit and claims of third parties however caused whether Ship freight prepaid to Pelco he negligence of Pelco or otherwise 3500 Pelco Way Clovi
30. he cursor gt beside Next Press the Iris Open button to go to the Next menu Position the cursor gt beside Auto Focus Mode P Press the Iris Open button The cursor moves to the right beside the word Auto or Off matically turned off when Move the joystick up or down to toggle between Auto and Off the shutter time is longer SELECT Press the Iris Open button on your keyboard to select your choice than 1 8 of a second CANCEL Press the Iris Close button if you do not want to change the setting NOTE Auto focus is auto NO O1 8 D gt 12 Pelco Manual C2423M 5 00 AUTO IRIS Main Menu Camera Menu Auto Iris Menu Camera Backlight comp Off Line Sync Zoom limit x72 Power Up Reset camera Auto iris mode Auto Aux lt Gain AGC gt Auto iris level 7 Alarms Zone Blank lt Auto iris gt Exit lt Other gt lt Next gt EXIT Exit The following are the settings for auto iris Mode Level To change the settings for auto iris Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the cursor gt beside Auto lris Press the Iris Open button The Auto Iris menu appears Position the cursor gt and select one of the following settings Gi 8 D MODE The cursor moves to one of two choices Auto The iris is automatically adjusted to produce a constant vid
31. he lris Close button if you do not want to change the setting ALARM PRIORITY Main Menu Alarms Zone Blank Menu Alarm Priority Menu Camera Line Sync Power Up Alarm resume Off Alarm dwell sec 5 Alarm priority Aux Alarms Zone Blank Other EXIT Alarm pattern Zone blank Exit This feature lets you set alarm priority inputs as one of the following High A high priority alarm will not release to a low priority alarm Low Alarms will release or sequence between low priority alarms only if no high priority alarm exists To change alarm priority Program preset 95 28 The main menu appears Position the cursor gt beside Alarms Zone Blank Press the Iris Open button to enter the Alarms Zone Blank menu Position the cursor gt beside Alarm Priority Press the Iris Open button to enter the Alarm Priority menu Position the cursor gt beside the number of the alarm input for which you want to set the priority Press the Iris Open button The cursor moves to the right beside the word High or Low Move the joystick up or down to toggle between the words High and Low SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting oo ROD o ON ALARM RESUME Pelco Manual C2423M 5 00 Main Menu Alarms Zone Blank Menu Camera Line Sync Power U
32. limit stops Pelco Manual C2423M 5 00 17 NOTE Programming preset 90 23 disables the manual limit stops until preset 91 24 is set NOTE On power up the auto scan tilt angle will be whatever angle the camera was at when the right scan limit was set 18 TURNING LIMIT STOPS ON OR OFF To change the limit stop mode Program preset 95 28 The main menu appears Position the cursor beside Other Press the Iris Open button to enter the Other menu Position the cursor beside Limit Stops Press the Iris Open button The cursor moves to the right beside the word On or Off Move the joystick up or down to toggle between On and Off SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting NU RD PROGRAMMING LIMIT STOPS Manual Limit Stops Refer to the documentation for your control system for programming presets and then do the following Make sure limit stops are turned ON and then exit the menu Push the joystick left until you reach the limit you want the camera to go to on the left Program preset 90 23 Push the joystick right to the limit you want the camera to go to on the right Program preset 91 24 Setting presets 90 23 and 91 24 to the same point disables manual limit stops Oi RO mi Scan Limit Stops Refer to the documentation for your control system for programming presets and the
33. minute to 720 minutes 12 hours or it can be set to zero which disables this feature To change the park time Program preset 95 28 The main menu appears Position the cursor gt beside Other Press the Iris Open button to enter the Other menu Position the cursor gt beside Park Time Minutes Press the Iris Open button The cursor moves to the right beside the current park time Move the joystick up or down to change the park time SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the Iris Close button if you do not want to change the setting NDJ AON PATTERN LENGTH CAUTION If the length is changed all patterns that were stored are erased Pelco Manual C2423M 5 00 Main Menu Other Menu Camera Auto flip On Line Sync Proportional pan On lt Power Up gt Limit stops Off Aux Park time minutes 0 Alarms Zone Blank Scan speed deg s 25 Pattern length 1 5 min EXIT Exit The Spectra Il dome can do the following One full pattern 1 5 3 or 6 minutes long or Two half patterns 75 1 5 or 3 minutes long This pattern can consist of any standard pan and tilt or lens command Presets flip and turbo are not allowed in a pattern Zone scan can be enabled while running a pattern To set the pattern length Program preset 95 28 The main menu appears Position the cursor beside Other Press the Iris Open button to enter
34. n do the following 1 Make sure limit stops are turned ON and then exit the menu Push the joystick left until you reach the limit you want the camera to go to on the left Program preset 92 25 Push the joystick right to the limit you want the camera to go to on the right Program preset 93 26 Setting presets 92 25 and 93 26 to the same point disables scan limit stops Qr Sab LINE SYNCHRONIZATION Main Menu Line Sync Menu Camera Line Sync Power Up Line sync On Aux Line sync phase Alarms Zone Blank Exit Other EXIT If cameras are out of phase with each other they may produce what appears to be vertical roll when switching between cameras There are two settings for line synchronization On Adjust the synchronization of the power line voltage so that it is in phase with other cameras Off The dome synchronizes to an internal clock To change the line synchronization settings 1 Program preset 95 28 The main menu appears 2 Position the cursor gt beside Line Sync 3 Press the Iris Open button The Line Sync menu appears 4 Position the cursor gt beside one of the choices Press the Iris Open button LINE SYNC The cursor moves to one of two choices ON or OFF Move the joystick up or down to toggle between them Press the Iris Open button to select the choice If you changed to OFF the camera may reset itself as it adjusts to the new synchronization
35. n it is panned or tilted more than 15 degrees If there is not enough light for a good picture when the iris is wide open you can increase the gain of the camera to improve the picture To increase the gain 1 Hold down the Iris Open button until the iris is wide open 2 Release the button 3 Within one second hold down the button again This starts increasing the camera gain Hold down the button until a desirable picture is obtained or the maximum gain is reached PROGRAMMING Programming Guide Spectra II Color Black amp White Gain AGC Menu 1 Access main menu preset 95 Make main menu selections Joystick Move up or down to position cursor or to toggle between selections Iris Open Enter Iris Close Cancel MAIN MENU Camera Line Sync Power Up Aux Alarms Zone Blank Other EXIT PRESETS The following presets are reserved for special functions Preset Function Camera Menu Backlight comp Off Zoom limit x72 Reset camera lt Gain AGC gt lt Auto iris gt lt Next gt Exit Line Sync Menu Line sync On Line sync phase Exit Power Up Menu Power Up Default Exit Aux Menu AGC mode Gain Exit Auto lris Menu IR Filter Menu Auto iris mode Auto Auto iris level T Exit IR Filter mode Auto Auto IR Level Dusk Exit Next Menti Sharpness Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto IR Filter gt l
36. o other alarms activated the dome resumes its prior activity So it might return to its previous position or resume a scan or pattern If there are other alarms activated the dome goes to them If you move the joystick to pan or tilt the dome or if you issue a lens command while there is an alarm the pan and tilt or lens command overrides the alarm Sixty seconds after the last pan and tilt or lens command the dome will return to the alarm preset if the alarm is still active Pelco Manual C2423M 5 00 Pelco Manual C2423M 5 00 AUXILIARY OUTPUTS An AUX 1 command from the controller will activate the relay in the dome and operate the device that is connected to the relay The relay will remain latched until a clear command is issued An AUX 2 command from the controller will place a ground at the output of AUX 2 to oper ate the device that is connected to it The output will remain latched until a clear command is issued The output relay can also be programmed so that it is activated when any alarm input is ac tivated When latching toggling is selected on the programming menu giving the AUX 1 command from the controller changes the state of the AUX for example if it was on this turns it off The clear command from the controller will turn the AUX off in the latching or toggle mode PARK If the dome does not receive any commands for a specified period of time refer to Park Time Minutes in the Programming section
37. om Off Disables proportional pan mode The pan speed will not depend on the amount of zoom To change the proportional pan mode Program preset 95 28 The main menu appears Position the cursor beside Other 1 2 Pelco Manual C2423M 5 00 Press the Iris Open button to enter the Other menu Position the cursor beside Proportional Pan Press the Iris Open button The cursor moves to the right beside the word On or Off Move the joystick up or down to toggle between On and Off SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting NOAA RESET CAMERA Main Menu Camera Menu lt Camera gt Backlight comp Off lt Line Sync gt Zoom limit x72 lt Power Up gt Reset camera lt Aux gt lt Gain AGC gt lt Alarms Zone Blank gt lt Auto iris gt lt Other gt lt Next gt EXIT Exit Resetting the camera returns the settings to their defaults Default Settings Backlight comp Off Zoom limit X72 Gain AGC AGC mode Auto Gain 6 Auto iris Mode Auto Level 7 Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto IR Filter IR filter mode Auto Auto IR level Dusk Sharpness 15 White balance Auto white bal On Red bal level No default Blue bal level No default When the camera is reset the following settings are not changed park time auto
38. oom limit SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the Iris Close button if you do not want to change the setting Pelco Manual C2423M 5 00 MAINTENANCE DOME CLEANING Clean the acrylic dome as necessary to maintain a clear picture Be careful not to scratch the surfaces of the dome Exterior Surface Clean the dome s exterior surface with a nonabrasive cleaning cloth and cleaning agent that is safe for acrylic Either liquid or spray cleaner wax suitable for fine furni ture is acceptable Interior Surface Except Chrome or Gold Clean the same as the exterior surface Interior Surface Chrome or Gold The inside surface of a chrome or gold dome is easily scratched Use the following precautions to maintain the dome s surface 1 Always handle the dome from the outside of its circular flange 2 Never touch the coated inside surface The acid in your fingerprints will eventually etch the coating if the fingerprints are not carefully removed according to the recommended cleaning procedure in item 5 3 If dust or other contaminants accumulate on the dome s interior remove the debris with compressed air Compressed air cans are available from photographic equipment or elec tronic supply dealers 4 If heavy residue accumulates and cannot be removed with air pressure rinse with water and immediately dry with air pressure so that water spots will not remain Avoid wiping the
39. our choice CANCEL Press the lris Close button if you do not want to change the setting AYO OT Roo Io EE eo Pelco Manual C2423M 5 00 IR FILTER MODE Main Menu Camera Menu Next Menu IR Filter Menu Camera Slow shutter mode Line Sync Power Up Backlight comp Zoom limit Reset camera lt Gain AGC gt lt Auto iris gt lt Next gt Shutter speed Auto focus mode gt IR Filter lt Sharpness gt White balance Previous IR Filter mode Auto IR Level Exit Aux Alarms Zone Blank Other EXIT Exit Exit There are two settings for the IR filter mode Auto IR filter switches in and out automatically Do the following to setup the IR filter for automatic operation CAMERA SETTING SETUP IR Filter Auto AGC mode Auto Shutter Speed Auto IMPORTANT The AGC mode and shutter speed must be set to Auto for the IR filter to operate automatically If the AGC mode or shutter speed is changed to a manual setting the IR filter setting automatically switches to OFF Off IR filter is manually operated The following presets are used to manually operate the IR filter Preset 88 21 Filter IN color Preset 89 22 Filter OUT black amp white To change the IR filter mode Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the
40. p Alarm resume Alarm dwell sec Alarm priority Aux p Alarms Zone Blank Other EXIT Alarm pattern Zone blank Exit This mode lets the dome resume its previous activity scan pattern or previous position after all alarms are cleared There are two alarm resume modes On Alarm resume mode is enabled Off Alarm resume mode is disabled To change the alarm resume mode Program preset 95 28 The main menu appears Position the cursor beside Alarms Zone Blank Press the Iris Open button to enter the Alarms Zone Blank menu Position the cursor gt beside Alarm Resume Press the Iris Open button The cursor moves to the right beside the word On or Off Move the joystick up or down to toggle between On or Off SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting NOAPRON 11 AUTO FLIP Main Menu Other Menu Camera Auto flip On Line Sync Proportional pan On Power Up Limit stops Off Aux Park time minutes 0 Alarms Zone Blank Scan speed deg s 25 Other Pattern length 1 5 min EXIT Exit There are two auto flip modes On Auto flip mode is enabled Off Auto flip mode is disabled To change the auto flip mode Program preset 95 28 The main menu appears Position the cursor beside Other Pre
41. s CA 93612 5699 REVISION HISTORY Manual Date Comments C2423M 5 00 Original version Pelco the Pelco logo Spectra Genex Legacy and PelcoVision are registered trademarks of Pelco Copyright 2000 Pelco All rights reserved TM Esprit Spectra Il and Camclosure are trademarks of Pelco U S Patent No 5 931 432 28 Pelco Manual C2423M 5 00
42. ss gt White balance Previous Exit Camera Backlight comp Line Sync Zoom limit Power Up Reset camera Aux lt Gain AGC gt lt Alarms Zone Blank gt lt AUto iris gt lt Other gt lt Next gt EXIT Exit There are several electronic shutter speed settings Auto 1 4 1 8 1 15 1 30 1 60 1 125 1 180 1 250 1 500 1 1000 1 2000 1 4000 1 10 000 In the Auto setting the camera controls the shutter speed automatically Increasing the shut ter speed lowers the light sensitivity but rapidly moving objects will be less blurred as the speed is increased To change the electronic shutter speed settings Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position the cursor gt beside Next Press the Iris Open button to go to the Next menu Position the cursor gt beside Shutter Speed Press the Iris Open button The cursor moves to the right beside the current shutter speed Move the joystick up or down to choose the shutter speed SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting PO o oO gio m Pelco Manual C2423M 5 00 23 SLOW SHUTTER MODE Main Menu Camera Line Sync Power Up Aux Alarms Zone Blank Camera Menu
43. ss the Iris Open button to enter the Other menu Position the cursor gt beside Auto Flip Press the Iris Open button The cursor moves to the right beside the word On or Off Move the joystick up or down to toggle between On and Off SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the Iris Close button if you do not want to change the setting NPRN AUTO FOCUS MODE Main Menu Camera Menu Next Menu lt Camera gt Backlight comp Off Slow shutter mode Auto lt Line Sync gt Zoom limit x72 Shutter speed Auto lt Power Up gt Reset camera Auto focus mode Auto Aux lt Gain AGC gt lt Sharpness gt lt Alarms Zone Blank gt lt Auto iris gt lt White balance gt lt Other gt lt Next gt Previous EXIT Exit Exit There are two auto focus modes Auto If auto focus is in the auto mode pressing the Focus Far or Focus Near button will place the focus in the manual mode The dome will return to auto focus if you pan or tilt the unit or do a zoom function Off If the mode is set to off the dome will operate in the manual mode with one ex ception If you issue a command to go to a preset auto focus will turn on and remain on until you press the Focus Far or Focus Near button To change the mode Program preset 95 28 The main menu appears Position the cursor gt beside Camera Press the Iris Open button to enter the Camera menu Position t
44. t 99 32 to start auto continuous scanning Scan limit stops are controlled by software Refer to the Limit Stops section to program the scan limit stops When the dome reaches a scan limit stop it reverses direction Call preset 96 29 to stop a scan Any pan tilt or lens command also will stop a scan ZONES The Spectra Il dome is capable of eight zones each with a 20 character label Depending on the controller you can define the zone size and define any zone as blanked for video when the camera pans into the zone area If zone labels are turned off the system displays the message VIDEO BLANK to indicate the video is being blanked and is not failing Re fer to Zone Blankin the Programming section for instructions NOTE The dome cannot do electronic zoom in a pattern Optical zoom will operate in a pattern PATTERNS The Spectra Il dome can do either one full pattern 1 5 3 or 6 minutes long or two half patterns 75 1 5 or 3 minutes long This pattern can consist of any standard pan and tilt or lens command Presets flip and turbo are not allowed in a pattern Zone scan can be enabled while running a pattern Refer to the documentation for your control system to program and run patterns ALARMS The Spectra Il dome has seven alarm inputs which can be designated as either high or low priority through its programming menu When an alarm is received the dome does one of the following Moves to the preset
45. t Sharpness gt lt White balance gt Previous Exit Sharpness Exit Alarm Priority Menu White Balance Menu Auto white bal On Red bal level Blue bal level 1 Park 3 1 7 Alarms if used Exit 33 Flip command 34 Pan zero command Aux 1 mode Normal 88 IR filter IN Aux 2 mode Normal Alarm Pattern Menu 89 IR filter OUT Exit 90 91 Manual limit stops 92 93 Scan limit stops 1No Pattern 2No Pattern 95 Select camera hs o menu Alarms Zone Blank Menu 96 Stop a scan 5No Pattern 97 Random scanning 6No Pattern 98 Frame scanning Alain r gis oft 7No Pattern 29 m Alarm dwell sec 5 lt Alarm priority gt lt Alarm GC Zone Blank Menu SC SES Video Blank Zone 10ff 20ff 30ff 4Off Other Menu 5Off 6Off 7Off Auto flip On DO Proportional pan On Limit stops Off Park time minutes 0 Scan speed deg s 25 Pattern length 1 5 min For detailed instructions refer to the following sections Exit Menu items are listed alphabetically 8 Pelco Manual C2423M 5 00 ACCESSING MAIN MENU PRESET 95 NOTE For American You can call up the main menu on your monitor by programming setting or creating preset Dynamics controllers with 95 28 if in 32 preset mode only 32 presets set switch SW1 7 on the dome drive in Programming preset 95 for Pelco s controllers varies according to the type of controller you the ON position When are using Instructions for programming preset 95 are given below for various Pelco SW1 7 is ON preset
46. the menu entitled Other Position the cursor gt beside Pattern Length Press the Iris Open button The cursor moves to the right beside the number of minutes 1 5 3 or 6 Move the joystick up or down to toggle through the number of minutes 1 5 3 or 6 SELECT Press the Iris Open button on your keyboard to select your choice CANCEL Press the lris Close button if you do not want to change the setting aos NO 19 POWER UP MODE Main Menu Power Up Menu Camera Line Sync Power Up Power Up Default Aux Exit Alarms Zone Blank Other EXIT This feature lets the dome resume a desired condition following power up The menu includes the following choices Default Park Scan Auto Scan Frame Scan Rand Full Pat Half Pat 1 Half Pat 2 On power up the dome goes through a configuration cycle and stops at zero reference showing Configuration Done address and mode set tings on the screen The dome moves to preset 1 when the power up sequence finishes The only text on the screen is the preset label if any is programmed The dome initiates scan mode when the power up sequence finishes Again there is no text The dome initiates a frame scan when the power up sequence finishes The dome initiates a random scan when the power up sequence finishes The dome initiates its programmed pattern when the power up sequence finishes The length can be set
47. ts downward and goes just beyond the vertical position the dome ro tates 180 degrees When the dome rotates flips the camera starts moving upward as long as you continue to hold the joystick in the down position Once you let go of the joy stick after the dome rotates joystick control returns to normal operation The auto flip fea ture is useful for following a person who passes directly beneath the camera Refer to Auto Flip in the Programming section SCAN SPEED Scan speed is adjustable from 1 to 40 degrees per second through the programming menu PRESET FUNCTIONS The Spectra Il dome is capable of going to 64 preset locations each with a 20 character la bel The presets are numbered 1 32 and 35 66 Refer to the documentation for your control System for programming presets When a preset operation is performed the amount of error in moving to the pan and tilt position is 1 2 degree If you command the dome to go to an undefined preset erratic operation may result Presets 33 and 34 are fixed commands meaning that you cannot program them Preset 33 is the flip command which will pan the dome drive 180 degrees Preset 34 is the pan zero command which will direct the dome drive to the factory determined zero reference point RANDOM FRAME AND AUTO SCANNING Call preset 97 30 to start random scanning Call preset 98 31 to activate frame scanning three seconds of scanning followed by a three second pause Call prese
48. y use replacement parts recommended by Pelco 4 After replacement repair of this unit s electrical components conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry 5 The installation method and materials should be capable of supporting four times the weight of the enclosure pan tilt camera and lens combination The product and or manual may bear the following marks This symbol indicates that dangerous voltage constituting a risk of electric shock is present CAUTION within this unit RISK OF ELECTRIC SHOCK i This symbol indicates that there are important DO NOT OPEN operating and maintenance instructions in the literature accompanying this unit Please thoroughly familiarize yourself with the information in this manual prior to installation and operation MEASURES DE SECURITE IMPORTANTES Avant d installer ou d utiliser ce produit les mesures de s curit suivantes sont prendre 1 Toute installation et r paration devraient tre entreprises par un technicien qualifi et conformes au codes locaux 2 A moins que cet equipement indique avoir un boiti agr e NEMA de type 3 3R 3S 4 4X 6 ou 6P il est uniquement con u pour utilisation int rieure et ne peut donc pas tre en contact de pluie ou d humidit 3 Utiliser seulement les pi ces de rechanges recommand es par Pelco 4 Apr s toute installation ou r paration de
Download Pdf Manuals
Related Search