Model DA440PBT PTO, Belt Driven Topdeck Compressor
Contents
1. Do not overfill the compressor with oil Use correct quantity of manufacturer s lubricant Repair leaks and clean spills immediately All electrical components and cable wiring must be installed and grounded in accordance with NFPA national electrical codes and applicable state and local codes Compressors generate high temperatures Do not touch or otherwise come in contact with hot surfaces Doing so can cause severe personal injury Before removing guards or servicing the compressor disconnect all power supplies Display warning signs and lock out electrical circuits All guards must be in position and secure before and during operation E DA440PBT 99900780 19990119 iii TABLE OF CONTENTS PARA TITLE PAGE SPARE PARTS LIST iv Section 1 INTRODUCTION 1 1 GENERAL INFORMATION 2 ORDERING INFORMATION Section 2 INSTALLATION 2 1 GENERAL 2 1 2 2 PTO INSTALLATION 2 1 2 3 UNDER DECK COMPRESSOR INSTALLATION 2 1 Section 3 OPERATION 3 1 OPERATION 3 1 3 2 SYSTEM SHUTDOWN 3 1 Section 4 PREVENTIVE MAINTENANCE 4 1 PREVENTIVE MAINTENANCE 4 1 4 2 LUBRICATION 4 1 4 3 PREVENTIVE MAINTENANCE CHECKLIST 4 1 Section 5 PARTS 5 1 COMPRESSOR PARTS 5 1 Section 6 REFERENCE LIST OF ILLUSTRATIONS FIGURE TITLE PART NUMBER PAGE D 1 TABLE PREVENTIVE MAINTENANCE CHECKLIST 4 1 DA440PBT COMPRESSOR RH 3 4 TON SGL WHEEL 23000146 1 5 1 DA440PBT COMPRESSOR RH 3 4 SGL WH2. BEARING PILLOW BLOCK 2 C 5 70580126 BELT B84 2 6 60120068 SHAFT 1 W 14 77041008 PRESSURE SWITCH 1 18 70048069 AIR FILTER 1 P 21 73054031 UNLOADER VALVE 1 G COMPRESSOR R30 70073051 REF 70073727 LP INTAKE VALVE 1 W REF 70073726 LP EXHAUST VALVE 1 W REF 70732447 HP INTAKE VALVE 1 W REF 73054340 HP EXHAUST VALVE 1 W REF 70073766 RING SET 1 W REF 70143298 RELEASE VALVE KIT 1 w REF 70732429 INTERCOOLER TUBE LH 1 W REF 70732430 INTERCOOLER TUBE RH 1 W REF 70732448 AIR FILTERS 1 P REF 76391490 SHAFT SEAL 1 W REF 73054339 POP OFF 70PSI 1 W REF 73054031 PILOT VALVE 1 C DA440PBT 99900780 19941223 SECTION 1 GENERAL INFORMATION 1 1 INTRODUCTION 1 2 ORDERING INFORMATION This manual provides information on the When placing orders or requesting assistance refer installation operation and repair of the IMT to the information below DA440PBt belt driven topdeck compressor Three means are used throughout this manual to gain the attention of operating and service personnel They are NOTES CAUTIONS and WARNINGS and are defined as follows NOTE A NOTE IS USED TO EITHER CONVEY ADDITIONAL INFORMATION OR TO PROVIDE FURTHER EMPHASIS FOR A PREVIOUS POINT CAUTION A CAUTION IS USED WHEN THERE IS THE STRONG POSSIBILITY OF DAMAGE TO THE EQUIPMENT OR PREMATURE EQUIPMENT FAILURE WARNING AWARNING IS USED WHEN THERE IS THE POTENTIAL FOR PERSONAL INJURY OR DEATH Operate this equipment with respect and
3. additional quantity of oil will be required 7 Start the engine engage the PTO and allow it to run for 5 10 minutes Check for leaks unusual noise and proper operation 8 Retorque the mounting bolts WARNING THE INSTALLER OF THE DRIVELINE MUST INSPECT THE FINAL POSITION OF THE DRIVELINE TO DETERMINE WHETHER ITS LOCATION PROVIDES SUFFICIENT PROTECTION TO AN OPERATOR OR OTHER PERSONNEL FROM HAZARDS ASSOCIATED WITH A ROTATING DRIVELINE IF PROTECTION IS INSUFFICIENT THE INSTALLATION OF A GUARD IS REQUIRED IF YOU ARE UNSURE OF METHODS TO GUARD A ROTATING DRIVELINE CALL IOWA MOLD TOOLING CO INC FOR INSTRUCTIONS FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH CONTACT WITH ROTATING DRIVELINE WILL CAUSE DEATH OR SERIOUS INJURY KEEP AWAY Keep clear of rotating drive shaft Never work on or near an installed power take off or driveline with the engine running 70392891 DA440PBT 99900780 19990119 2 2 2 3 TOP DECK COMPRESSOR INSTALLATION Due to the large variety of carrier vehicles the instructions in this paragraph should be used as a guide only Refer to Figure E 2 for reference 1 Position the compressor across the frame of the truck in the desired location The location selected should provide adequate ventilation while at the same time affording access to the compressor 2 Lift the compressor base into position Check for belt clearance and approxim
4. BOW 1 4 45 1 24 72053245 PIPE PLUG 1 4NPT 1 25 72060093 SCR 1 2 13 1 1 2 HHGR5 4 26 72063005 WASHER 1 2 WRT 4 27 72062080 NUT 1 2 13 LOCK 4 28 72060108 SCR 1 2 13X6 HHGR5 2 29 60118856 SUPPORT 1 DA440PBT COMPRESSOR LH 1 TON DUAL WHEEL 23000147 1 DA440PBT 23000147 02 19961014 5 5 VIEW ey N gt lt 7 PART OF ITEM 4 DA440PBT COMPRESSOR LH 1 TON DUAL WHEEL 23000147 2 DA440PBT 19990119 5 6 DA440PBT 99900780 19941223 6 1 SECTION 6 REFERENCE TORQUE DATA CHART DOMESTIC FINE THREAD BOLTS COARSE THREAD BOLTS SAE J429 SAE J429 SAE J429 SAE J429 GRADE 5 GRADE 8 GRADE 5 GRADE 8 REEN 5 16 24 19 14 27 20 5 16 18 17 13 25 18 3 8 24 3 8 16 7 16 20 7 16 14 1 2 20 1 2 13 9 16 18 9 16 12 5 8 18 5 8 11 3 4 16 3 4 10 7 8 11 7 8 9 1 12 1 8 1 1 8 12 1 1 8 7 1 1 4 12 1 1 4 7 1 3 8 12 1 3 8 6 1 1 2 12 1 1 2 6 When using the torque data in charts above the following rules should observed 1 Bolt manufacturer s particular specifications should be consulted when provided 2 Flat washers of equal strength must be used 3 Alltorque measurements are given in foot pounds To convert to inch pounds multiply by 12 4 Torque values specified are for bolts with residual oils or no special lubricants applied If special lubricants of high stress ability such as Never Seez compound graphite and oil molybdenum
5. DA440PBT 99900780 19990119 ha Model DA440PBT 7 PTO Belt Driven Topdeck Compressor Previously Model 80 Driven Topdeck MT IOWA MOLD TOOLING INC BOX 189 500 HWY 18 WEST GARNER IA 50438 TEL 515 923 3711 TECHNICAL SUPPORT FAX 515 923 2424 MANUAL PART NUMBER 99900780 DA440PBT 99900780 19980224 P R E CA U 5 Read before operating your compressor 44 DANGER EXPLODING TANK WILL CAUSE DEATH SERIOUS INJURY OR PROPERTY DAMAGE Drain air tank after each use to prevent moisture build up and corrosion which leads to tank failure Assure that tank and compressor relief valves work properly and are at correct pressure settings DO NOT modify or repair air tank NEVER drive vehicle with pressure in air tank 988E6ELZ Do not use air from this compressor for breathing or food processing Air from Failure to follow operating and maintenance procedures as outlined in this manual could result in equipment damage personal injury this compressor will cause or death Follow all maintenance severe injury or death if used procedures and intervals for breathing or food processing Hot oil under pressure can cause severe injury or death Shut down let cool and relieve pressure in compressor before servicing Maintenance must be performed only by trained and qualified personnel using correct tools specified torques and approved replacement parts
6. EEL 23000146 2 5 2 INSTALLATION HARDWARE RH 3 4 TON SGL WHEEL 5 3 DA440PBT COMPRESSOR LH 1 TON DUAL WHEEL 23000147 1 5 4 DA440PBT COMPRESSOR LH 1 TON DUAL WHEEL 23000147 2 5 5 DA440PBU COMPRESSOR CW TRANSMISSION 23000952 1 5 6 DA440PBU COMPRESSOR CW TRANSMISSION 23000952 2 5 7 F 1 TORQUE DATA CHART 6 1 F 2 TIRE LOAD AND INFLATION PRESSURES 6 2 DA440PBT 99900780 19980224 iv RECOMMENDED SPARE PARTS LIST 1 Year Supply DA440PBT PTO BELT DRIVEN TOPDECK COMPRESSOR For Manual 99900780 This spare parts list does not necessarily indicate that the items can be expected to fail in the course of a year It is intended to provide the user with a stock of parts sufficient to keep the unit operating with minimal down time walting for parts There may be parts failures not covered by this list Parts not listed are considered as not being Critical or Normal Wear items during the first year of operations and you need to contact the distributor or manufacturer for availability SHELF ASSEMBLY LIFE ORDER DESIGNATION PARTNO DESCRIPTION QTY CODE MO 23000146 01 19970624 RH 3 4 SINGLE WHEEL COMPRESSOR 5 60111268 SHAFT BELT 18 1 w 6 60118327 SHAFT BELT 15 1 w 8 70580116 BELT BP70 2 9 70580115 BELT BP33 2 12 70055062 BEARING PILLOW BLOCK 4 24 77041008 PRESSURE SWITCH 1 31 70048069 AIR FILTER 1 P 32 73054031 UNLOADER VALVE 1 23000147 01 19961014 LH 1 DUAL WHEEL COMPRESSOR 4 70055062
7. RESSOR RH 3 4 TON SINGLE WHEEL 23000146 1 QTY al N nm P ch ch DA440PBT 23000146 02 19960723 SINGLE WHEEL 23000146 2 DA440PBT COMPRESSOR RH 3 4 5 3 DA440PBT 19941223 d od LO 9 e x no cc O gag SLI Oz 02 LO LO gt ON Oo CC ECH e 4 DO eo WR Nu Qn SS TY W ENS 3 4 TON SINGLE WHEEL INSTALLATION HARDWARE RH DA440PBT 23000147 01 19961014 5 4 ORGINIAL PART OF COMPRESSO TO SPEED CONTROL IDLE PRESSURE 14 21 TANK ab CX PART OF COMPRESSOR 23 PILOT UNLOADER 18 ITEM PART NO DESCRIPTION QTY 14 77041008 PRESSURE SWITCH 15 72532552 HOSE FITTING 1 4 1 4 ITEM PART NO DESCRIPTION QTY 1 52713749 FRAME WELDMENT LH 1 2 70073051 COMPRESSOR 1 3 52706205 TIGHTENER BOLT 4 2 18 70048069 AIR FILTER 4 70055062 BEARING PILLOW BLOCK 2 19 72532013 STREET TEE 1 4 BRS 5 70580126 BELT B84 GATES 9093 2083 2 21 73054031 UNLOADER VALVE 6 60120068 SHAFT 1 1 4 X 10 1 4 1 22 72053411 PIPE PLUG 1 8 SQHD 7 70056111 BUSHING 1 8 70056523 PULLEY DUAL GROOVE 9 1 9 72060102 CAP SCR 1 2 13X5 1 2 HHGR5 2 10 72062080 1 2 13 LOCK 4 11 72063005 WASHER 1 2 WRT 4 12 72532974 STREET ELBOW 1 4 90 SHT 1 13 72053013 PIPE 1 4 X CLOSE 1 1 1 1 1 1 1 23 72053533 STREET EL
8. anual has been compiled and checked but errors do occur To provide our customers with a method of communicating those errors we have provided the Manual Change Request form below In addition to error reporting you are encouraged to suggest changes or additions to the manual which would be of benefit to you We cannot guarantee that these additions will be made but we do promise to consider them When completing the form please write or print clearly Submit a copy of the completed form to the address listed below MANUAL CHANGE REQUEST COMPANY ADDRESS CITY STATE ZIP TELEPHONE error FOUND LOCATION OF ERROR page no DESCRIPTION OF ERROR REQUEST FOR ADDITION TO MANUAL DESCRIPTION OF ADDITION REASON FOR ADDITION MAILTO IOWA MOLD TOOLING Co Inc Box 189 Garner IA 50438 0189 ATTN Technical Publications DA440PBT 99900780 LIMITED WARRANTY WARRANTY COVERAGE Products manufactured by Iowa Mold Tooling Co Inc IMT are warranted to be free from defects in material and workmanship under proper use application and maintenance in accordance with IMT s written recommendations instructions and specifications as follows 1 Ninety 90 days labor on IMT workmanship from the date of shipment to the end user 2 One 1 year original IMT parts from the date of shipment to the end user IMT s obligation under this warranty is limited to and the sole remedy for any such defect
9. ate drive shaft length 3 Using the base as a template drill four 17 32 diameter holes The 3 4 ton RH will be drilled through the top of frame rails The 1 ton LH will be drilled through the sides of the frame rails 4 On the 3 4 ton LH insert spacers between base and frame rails No spacers are used with the 1 ton RH Bolt the compressor base to the frame of the truck using the 1 2 hardware 5 Using the appropriate driveshaft with knuckles in place measure the exact length required cut off excess shaft and weld in place 1 4 weld all around 6 Install the driveshaft to the PTO and the compressor tighten the lock bolts and tie wire in place 7 Tighten all bolts per Torque Data Chart 8 Connect the 3 4 air hose from the compressor to the air tank 9 Install the engine speed control and connect the hoses from compressor to speed control DA440PBT 99900780 19950719 3 1 OPERATION This section deals with the proper methods of system operation and shutdown These procedures should be followed to prevent damage and ensure efficient operation Start the compressor as follows 1 Ensure the PTO is disengaged and the receiver drain cock is open 2 Start the truck engine and allow it to idle until it reaches the proper operating temperature refer to the Owner s Manual 3 Depress the clutch engage the carefully release the clutch pedal 4 Activate the engine speed control by closin
10. awings are intended to be used in conjunction with the instructions found elsewhere in this manual For information pertaining to the compressor refer to its specific manual SPEED CONTROL IDLE PRESSURE ITEM PART NO 52712404 52712567 52706205 52704923 60111268 60118327 70073051 70580116 70580115 70056272 70056388 70055062 70143234 72060957 72060094 72060095 ORIGINAL PART OF COMPRESSOR 24 DESCRIPTION BASE WELDMENT BEARING BRACKET TIGHTENER BOLT 4 SCREW BELT TIGHTENER SHAFT BELT 18 SHAFT BELT 15 COMPRESSOR R30 BELT BP70 GATES 9003 2070 BELT BP33 GATES 9003 2033 PULLEY SHEAVE 4 2 GROOVE BEARING PILLOW BLOCK BUSHING CARR BOLT 1 2 13X2 SQNK GR2 SCR 1 2 13X1 3 4 HHGR5 CAP SCR 1 2 13X2 HHGR5 32 PART COMPRESSOR TT SSS PILOT UNLOADER ITEM PART NO 17 18 19 20 21 22 23 24 27 28 29 72062007 72062080 72063005 72053013 72532013 72053411 72053533 77041008 72532552 72532974 72601430 70048069 73054031 72053245 70056116 72035361 SECTION 5 PARTS DESCRIPTION NUT 3 4 10 HEX NUT 1 2 13 LOCK WASHER 1 2 WRT PIPE NIPPLE 1 4 X CLOSE STREET TEE 1 4 BRS PIPE PLUG 1 8 SQHD STREET ELBOW 1 4 45 PRESSURE SWITCH HOSE FITTING 1 4 1 4 STREET ELBOW 1 4 90 SHT CARR BOLT 3 8 16 2 SQNK GR2 AIR FILTER UNLOADER VALVE PIPE PLUG 1 4 BUSHING SPLIT TAPER GREASE ZERK 1 8 90 DA440PBT COMP
11. disulphite collodial copper or white lead are applied multiply the torque values in the charts by the factor 90 The use of Loctite does not affect the torque values listed above 5 Torque values for socket head capscrews are the same as for Grade 8 capscrews FIGURE F 1 TORQUE DATA CHART DA440PBT 99900780 19941223 6 2 SINGLE TIRES FOR TRUCKS IN HIGHWAY SERVICE TIRE LOAD 50 TRE HOAD LIMITS AT VARIOUS INFLATION PRE RE 19 OOOOOOQ N N NNN N 1 1 e G TIG TIG Tl TiIITI IITIITIO Im O 1 1 1 1 1 1 DUAL FOR TRUCKS HIGHWAY SERVICE 40 45 50 55 60 65 70 75 80 85 90 noo DD OO OO 0 OO NN NN ZOS m o G TIG TIG TI TIITI IITIITIO Im O INFLATION PRESSURES ESTABLISHED FOR SIZE DEPENDING UPON THE LOAD IMPOSED ON THE TIRE FOR GREATER SABILITY RIDING COMFORT AND PROLONGED TIRE LIFE TIRES SHOULD BE INFLATED FOR THE LOADS CARRIED THE LOAD AND INFLATION TABLE SHOWN ABOVE INDICATES THE PROPER INFLATION PRESSURES TIRE AND RIM ASSOCIATION STANDARD TIRE LOADS AT VARIOUS INFLATION PRESSURES LOAD RANGE LETTERS AND CORRESPONDING PLY RATING D 8 PLY E 10 PLY 12 PLY AND G 14 PLY FIGURE F 2 TIRE LOAD AND INFLATION PRESSURES DA440PBT 99900780 The information within this m
12. ed WARRANTY VOIDED All obligations of IMT under this warranty shall be terminated 1 if service other than normal maintenance or normal replacement of service items is performed by someone other than an authorized IMT dealer 2 if product is modified or altered in ways not approved by IMT PURCHASER S RESPONSIBILITY This warranty covers only defective material and workmanship It does not cover depreciation or damage caused by normal wear accident improper protection in storage or improper use The purchaser has the obligation of performing the care and maintenance duties discussed in IMT s written recommendations instructions and specifications Any damage which results because of purchaser s failure to perform such duties shall not be covered by this warranty The cost of normal maintenance and normal replacement of service items such as filters belts etc shall be paid by the purchaser CONSEQUENTIAL DAMAGES The only remedies the purchaser has in connection with the breach or performance of any warranty on IMT products are those set forth above In no event will the dealer IMT or any company affiliated with IMT be liable for business interruptions loss of sales and or profits rental or substitute equipment costs of delay or for any other special indirect incidental or consequential losses costs or damages REPRESENTATIONS EXCLUDED IMT products are subject to no expressed implied or statutory warranty other than h
13. erein set forth and no agent representative or distributor of the manufacturer has any authority to alter the terms of this warranty in any way whatsoever or to make any representations or promises express or implied as to the quality or performance of IMT products other than those set forth above CHANGE IN DESIGN IMT reserves the right to make changes in design or improvements upon its products without imposing any obligation upon itself to install the same upon its products theretofore manufactured Effective January 1985 This parts manual is provided to the user to assist in servicing the equipment It is the propertyof Iowa Mold Tooling Co Inc and as such may not be reproduced either whole or in part whether by chemical electrostatic mechanical or photographic means without the expressedwritten permission of an officer of Iowa Mold Tooling Co Inc One manual is provided with each piece of new equipment and additional manuals may be obtained at a nominal price MP IOWA MOLD TOOLING CO INC BOX 189 GARNER IA 50438 0189 TEL 515 923 3711 TECHNICAL SUPPORT FAX 515 923 2424
14. g the receiver drain cock The compressor is now operating and supplying working air NOTE WHEN STARTING THE COMPRESSOR THE RPM S WILL AUTOMATICALLY INCREASE DUE TO LOW VOLUME OF AIR IN THE SYSTEM CAUTION 1000 RPM MAX Operating this unit in excess of 1000 RPM measured at the compressor flywheel will void your warranty Engine RPM may be different SECTION 3 OPERATION 3 2 SYSTEM SHUTDOWN System shutdown is accomplished as follows 1 Allow the compressor to build to maximum pressure and the truck engine will automatically idle down 2 Place the compressor control valve in the open off position 3 Depress the clutch pedal and disengage the PTO 4 Open the receiver drain cock and discharge the air in the receiver WARNING FEDERAL LAW PROHIBITS DRIVING THE CARRIER VEHICLE ON PUBLIC ROADS WITH THE RECEIVER FILLED WITH COMPRESSED AIR ALWAYS DRAIN THE RECEIVER BEFORE MOVING THE VEHICLE DA440PBT 99900780 19950719 3 2 NOTES DA440PBT 99900780 19941223 4 1 Section 4 PREVENTIVE MAINTENANCE 4 1 PREVENTIVE MAINTENANCE CAUTION USE ONLY 30W NON DETERGENT IN THE EEN COMPRESSOR DO NOT USE SYNTHETIC essential to keep your unit operating efficiently Proper maintenance procedures and required service 4 3 PREVENTIVE MAINTENANCE inte
15. or reuse If the vehicle is used drain and dispose of the transmission oil 2 Temporarily install the with the proper gaskets and only two studs Snug the PTO down and check the backlash for maximum allowance of 1 32 to 1 16 If the backlash is excessive remove gaskets and check backlash again until it is corrected 3 Remove the PTO and apply Permatex to the gaskets If the holes for the studs are tapped through the transmission housing apply Permatex to the studs and tighten them down Make certain that the studs do not interfere with the transmission gears CAUTION AVOID CONTACT OF PERMATEX WITH TRANSMISSION FLUID 4 Install the and gaskets Torque the nuts to 30 35 ft Ibs 4 14 4 84 kg m for a 6 bolt and 45 50 ft Ibs 6 22 6 91 kg m for 8 bolt PTO s Recheck the backlash 5 Install the shifter cable to suit conditions Always allow for a slight overshift on lever or knob to ensure the PTO is fully disengaged CAUTION IT IS IMPORTANT THAT ADEQUATE SPACE BE ALLOWED FOR FULL ENGAGEMENT OF THE PTO MODIFY THE EXHAUST OR OTHER OBSTRUCTIONS AS NEEDED SECTION 2 INSTALLATION CAUTION AVOID SHARP BENDS IN THE SHIFTER CABLE ALL BENDS SHOULD HAVE AT LEAST A 6 RADIUS TIGHTER BENDS WILL CAUSE DIFFICULT OPERATION OF THE SHIFTER KNOB 6 Replace the transmission oil If the is located below the transmission oil level an
16. rvals are outlined in this section Personnel CHE CKLIST responsible for unit upkeep should become familiar esp The checklist Figure is designed to assist you in with frequency and type of maintenance required i e S keeping your unit in efficient operating condition and perform these tasks at recommended intervals iae Items in this section apply to the unit only The carrier vehicle should also be inspected regularly 4 2 LUBRICATION refer to the carrier vehicle s service manual The only lubrication required is on the carrier vehicle and the compressor itself Refer to the appropriate Owner s Manual for information on the truck and compressor for the type and frequency of lubrication required ITEM DESCRIPTION INTERVAL HOURS MONTHS EVERY DAILY WEEKLY 200 uns 5008 1000 6 1500 9 2000 12 EEE COMPRESSOR AIR INTAKE INSPECT AND CLEAN FRAME OIL LEVEL CHECK FRAME OlL CHANGE VALVES INSPECT AND CLEAN OPERATE SAFETY VALVES CLEAN SAFETY VALVES V BELT DRIVE BELT TENSION CHECK RECEIVER DRAIN CONDENSATION MANUAL OPERATE SAFETY VALVES GENERAL CHECK AND TIGHTEN ALL BOLTS CHECK ALL ELECT CONNECTIONS CHECK LUBRICATION FIGURE A PREVENTIVE MAINTENANCE CHECKLIST DA440PBT 99900780 19941223 4 2 DA440PBT 23000146 01 19970624 5 1 COMPRESSOR PARTS This section contains the exploded parts drawings with accompanying parts lists for associated assemblies These dr
17. service it regularly These two things can add up to a safer working environment and longer equipment life TO BE CONPLETED BY DEALER CHASSIS INFORMATION TRANSMISSION MAKE MODEL PTO NUMBER PTO COMPRESSOR AND HYDRAULIC PUMP INFORMATION COMPRESSOR MODEL SERIAL NUMBER PUMP MAKE MODEL RESERVOIR CAPACITY ENGINE RPM DA440PBT 99900780 19941223 1 2 NOTES DA440PBT 99900780 19990119 2 1 GENERAL This section deals with the installation of the PTO The instructions are intended as a guide to assist you with your particular installation We can not cover every make model and year of truck manufactured world wide so these instructions will provide only general information Use this information as a guide only 2 2 PTO INSTALLATION Power take off manufacturers provide specific installation instructions for their products Those instructions should be followed when installing a PTO Some trucks may require modification of the transmission cross member to provide clearance and the exhaust pipe may need modification Check with the manufacturer s representative for specific instructions regarding your particular make model and year of vehicle The following instructions are a guide in this application 1 Ifthe vehicle is new drain the transmission oil into a clean container f
18. shall be the repair or replacement at IMT s option of unaltered parts returned to IMT freight prepaid and proven to have such defect provided such defect occurs within the above stated warranty period and is reported within fourteen 14 days of its occurence IMPLIED WARRANTY EXCLUDED This is the only authorized IMT warranty and is in lieu of all other express or implied warranties or representations including any implied warranties of merchantability or fitness for any particular purpose or of any other obligations on the part of IMT ITEMS EXCLUDED The manufacturer gives no warranty on any components purchased by the manufacturer and such components as are covered only by the warranties of their respective manufacturers WARRANTY CLAIMS Warranty claims must be submitted and shall be processed in accordance with IMT s established warranty claim procedure WARRANTY SERVICE Warranty service will be performed by any IMT distributor authorized to sell new IMT products of the type involved or by any IMT Service Center authorized to service the type of product involved or by IMT in the event of direct sales made by IMT At the time of requesting warranty service the purchaser must present evidence of the date of delivery of the product The purchaser shall pay any premium for overtime labor requested by the purchaser any charge for making service calls and for transporting the equipment to the place where warranty work is perform
Download Pdf Manuals
Related Search