Home

INSTRUCTIONS

1. HARLEY DAVIDSON J00430 INSTRUCTIONS Kit Numbers 68431 95 and 68432 95 REV 5 1 95 FLAT LENS TURN SIGNAL KIT General These kits differ as follows Part No 68431 95 Contains 4 single filament lamp assemblies Part No 68432 95 Contains 2 single and 2 dual filament lamp assemblies These kits are designed for installation on the following model motorcycles Part No 68431 95 may be installed on all 1973 and later XL FX Softail except Heritage FXR except FXRT and Dyna models not equipped with running lights Part No 68432 95 may be installed on all 1986 and later XL FX Softail except Heritage FXR except FXRT and Dyna models equipped with running lights Kit Contents These kits contains the following components PART NO 68431 95 QTY DESCRIPTION 8 Butt connectors included with turn signal assemblies 4 Turn signal lamp assemblies single filament PART NO 68432 95 QTY DESCRIPTION 10 Butt connectors included with turn signal assemblies 2 Turn signal lamp assemblies single filament 2 Turn signal lamp assemblies dual filament Installation AwarninG To avoid accidental start up of the vehicle and possible personal injury disconnect battery cables negative cable first before performing any wiring procedures Rear Directional REMOVING ORIGINAL EQUIPMENT OE REAR DIRECTIONALS 1 Refer to the Service Manual that covers model being worked on and remove seat 2
2. Reach under fender or fender supports and follow wire s forward to area under seat Find a convenient location at which to cut the stock wire s Before cutting the wires measure the wire length on the lamp assem blies to make sure the new wires will reach to the loca tion selected Cut stock wire s Note position and routing of wires back to stock directional lamp Remove wire s from clips under fender and remove directional lamp assembly and attached wires INSTALLING REAR FLAT LENS DIRECTIONAL NOTE The fender struts and shocks may need to be removed on the Dyna Wide Glide to route the wire s from rear to under seat 1 Mount the new flat lens directional and route the new wires in the same location as the stock wires that were removed in step 3 above 2 Make wire connections following step 2A or 2B as applicable Strip wires 3 8 in insert wires into butt connector and crimp connector with Packard 115 crimper or equivalent 2A If stock lamp had only one wire connect the violet wire of the new lamp to the stock wire using one of the butt connectors contained in the kit Either ground or remove the black wire connected to the new directional 2B If stock lamp had two wires connect the violet wire of the new lamp to the stock violet brown or copper stranded wire Stagger the connectors to allow the conduit to cover the splices Connect the two remaining black wires together using one of the butt connectors contained in
3. the kit 3 Repeat Removal and Installation for other rear directional 4 Test the directional signals using the procedure in the WARNING at the end of this procedure Front Directional REMOVING OE FRONT DIRECTIONALS 1 Follow wire s from front directional and find a convenient location at which to cut the stock wire s Before cutting the wires measure the wire length on the lamp assemblies to make sure the new wires will reach to the location selected 2 Cut stock wire s Note position and routing of wires back to stock directional lamp Remove directional lamp assembly and attached wires 1 of 2 INSTALLING FRONT FLAT LENS DIRECTIONAL 1 Mount the new flat lens directional and route the new wires in the same location as the stock wires that were removed in step 2 above NOTE The stock directional light wiring is identified as follows Lamps with one lead have black wire with copper strands Lamps with two leads have one wire with copper strands for directional light filament 32 candle power and another wire with silver strands for running light filament 2 candle power Lamps with three leads have wires color coded as follows violet brown for directional light filament blue for running light filament black for ground wire 2 Make wire connections following step 2A 2B or 2C as applicable Strip wires 3 8 in insert wires into butt connector and crimp connector with Packard 115 crimper or equivalen
4. 95 68432 95 Date 5 95 Flat Lens Turn Signal Kit 68432 95 Part No 31509 80 68168 89 68395 95 68759 96 68499 95 68572 64B Item Description Butt connector Bulb dual filament Turn signal dual filament Lens flat Turn signal single filament Bulb single filament J00430 68431 95 Part No 31509 80 68759 96 68499 95 68572 64B Description Butt connector Lens flat Turn signal single filament Bulb single filament 2 of 2
5. t 2A If stock lamp had only one wire connect the violet wire of the new lamp to the stock wire using one of the butt connectors contained in the kit Either ground or remove the black wire connected to the new directional 2B If stock lamp had two wires connect the violet wire of the new lamp to the stock violet brown or copper stranded wire Stagger the connectors to allow the conduit to cover the splices Connect the two remaining black wires together using one of the butt connectors contained in the kit 2C If stock lamp had three wires connect the violet wire of the new lamp to the stock violet brown wire Stagger the connectors to allow the conduit to cover the splices Connect the blue wires together and connect the two remaining black wires together using the butt connectors contained in the kit 3 Repeat Removal and Installation for other front directional 4 Test the directional signals using the procedure in the following WARNING WARNING Test directional signals after finishing installation Weak intermittent or non operational lights indicate a poor connection or a short in the wires The motorcycle must never be operated in this condition as it could result in personal injury or vehicle damage Inspect the bulb and socket Examine wiring for bare spots or loose connectors After reinstalling the wiring test directional signals again for satisfactory operation SMOTORZ 2 Service Parts P N 68431

INSTRUCTIONS

Contents

Download Pdf Manuals

Related Search

Related Contents