Home

Miscellaneous Service Bulletin Manual

1. Bulletin No Date All Hydraulic mowers using the 02964028 Push Pull Switch 092895 Sep 28 1995 Failures of the mower push pull switch Alamo has recently received reports of failures of the referenced switch The failures modes are a Knob pulls off rod b Rod and Knob pulls out of switch body Test performed on numerous switches indicates that the b failures are due to excessive force being applied to the knob when shutting off the mower Specifically the knobs are usually roughly slapped to turn the mower off After internal parts of the switch are damaged the rod can then be pulled out easily The a failures are due to the knobs not being securely tightened To prevent these failures from occurring or to replace a damaged switch use the following procedure to adjust the travel of the switch See attached diagram 1 Install the switch body in the holder and tighten the nut Screw the Knob on the rod to the bottom of the thread but do not overtighten It will probably be necessary to hold the rod with pliers to get the knob tight if you do use caution not to score the rod with the pliers 3 Measure the distance if any between the knob and the nut Record the measurement 4 If a Gap exists between the knob and the nut remove the knob 5 Remove the nut and install the same thickness of flat washers that was measured in step 3 Install and tighten the nut gt DO NOT install more washers than needed
2. Old 0711897A Jul 18 1997 Remote Control Cable Update Early in October of 1996 the control valve remote operating system design for the mowers listed above was updated to facilitate much easier operation of the mower control functions The retrofit Kit is available which can be used to update the former remote control system to the new design on those machines utilizing the old system The old style controller is identified as a rectangular metal box utilizing a cable linkage system Parts Needed Qty 1 of P N 02971493 Retrofit Kit contains the controller and all necessary mounting pieces Qty 4 of P N Valve Cables The Length of the cables must be specified when ordering Cable Length 48 60 72 or 102 Specify which is needed Procedure All the required Procedure New Style instructions should be included in a Control Levers instruction sheet that should be included in with the retrofit kit when ordered Instruction Sheet P N 02971261 Figure 1 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 25 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 080897 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models McConnel Boom Units Bulletin No Date 080897 Aug 8 1997 Specifications For McConnel Boom Flail Units The McConnel boom hydraulic systems we
3. Blade Bolt Inspection Recall Subject The Blade Bolt Nut Retaining Roll Pin Bore may be oversized and could allow the roll pin to become loose in the bore The loose roll pin could therfore allow the blade bolt Nut to loose torque Service Required 1 Visually inspect and check the fit of the roll pin If itis loose or has come loose replace the Blade Bolt Blade Bolt Nut and Roll Pin on the above listed serial numbered units 2 Torque the Blade Bolt to 600 ft Ibs before installing the new Roll Pin Parts Required Part No Qty Description 02782900 2 Blade Bolt 00020900 2 Nut 00023200 2 Roll Pin Figure 1 Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial Warranty Policy Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 11 INDUSTRIAL SERVICE BULLETIN No 992704 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models New Holland tractors T7740 amp T6640 Bulletin No S N Range listed below 992704 New Holland Tractors with Alamo Industrial Units mounted on Old 990003A Apr 27 1999 them only S N and model tractors listed below Labor Old Parts Disposition Termination Date 100 at Dealer Net O hr see New Holland s
4. MISCELLAN EOUS MODELS INFORMATION amp SERVICE BULLETINS Alamo Industrial eguin Texas 830 372 3551 BOOK INTRODUCTION INFORMATION amp SERVICE BULLETINS This Book is divided into two Sections Section One Technical Information Bulletins 1 Technical Information Bulletins Information Bulletins are listed by Bulletin Number Date Example the oldest Bulletin will be listed first and the most recent bulletin will be listed last Bulletin No 021002 first 8 second digits are the month the third amp fourth digits are the day of the month and the fifth amp sixth digits are the year this means the bulletin was written on Feb 10 2002 If more than one bulletin was written on that day the a dash with a number will added example 1 2 etc 2 Authorize Repairs Technical Information Bulletins do not authorize any repairs to be made under warranty or any other circumstance unless specifically instructed to do so 3 Bulletin Reference Some Technical Information Bulletins will refer to the corresponding Service Bulletins for repairs and some are for information only 4 Bulletin Instructions Technical Information Bulletins should have all the instructions as to what you need but may not have all the information needed to make an installation complete In some cases it may be required to refer to other manuals for more complete information this should be suggested in the Technical Information Bulletin 5 All Te
5. Alamo Group Inc 1 26 Information Bulletin 080897 Continued from previous Page Specifications For McConnel Boom Flail Units Feature Min Pump Relief Trac GPM Valve HP Wat a F Rotor Setting Oil F Rotor PA 91 25 HP 3045 PSI PA 92 60 HP 2750 PSI PA 93 60 HP 2750 PSI PA 94 60 HP 2750 PSI PA 95 65 to 75 HP 2750 PSI PA 96 65 to 75 HP 2750 PSI PA 97 9000 Ibs 2750 PSI PA 2060 65 to 75 HP 2750 PSI PA 2070 65 to 75 HP 2750 PSI PA 2080 10000 Ibs 2750 PSI TECHNICAL INFORMATION BULLETIN No 080897 Contact Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 Ph 830 372 2708 Fax 830 372 9603 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 27 TTT RAMS TECHNICAL INFORMATION BULLETIN No 031000 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Models mounted on New Holland TS Series Tractors Bulletin No Date 031000 Mar 10 2000 New Holland TS Series Fuel Filter New Holland ships TS100 Tractors to Alamo Industrial with a 87801634 fuel filter installed New Holland has circulated a service bulletin stating that a longer or taller filter is the replacement part for the fuel filter and the filter should be changed at the recommended time Alamo Industrial TS Series mount kit components will interfere with the longer taller filter
6. Always keep adding blocking near the center of the cab 4 Remove the cab support bolts and continue to raising the cab as high as possible taking care not to stretch any hoses cables or wires The wire to the fuel sender must be removed and the sender and straightened out and reinstalled before cab can be fully raised Wire to potentiometer on the end of the rockshaft must be removed or plastic tie cut to allow sufficient slack The hose to the right hand steering cylinder mut be removed from the metal loop under the cab floor Do not replace it in the metal loop but connect it directly to the cylinder MISCELLANEOUS MODELS Continued Next Page 2004 Alamo Group Inc 24 Service Bulletin 930510 Continued from previous Page Removal of Standard Valve see Figure 1 1 Remove the spool control link of the standard valve section item 3 at the control shaft arm by removing the cotter pin and the drilled in on the end of the valve section 2 Remove the hoses that are connected to the valve end plate and the hoses connected to the standard valve section 3 Remove the valve assembly support bolt on right hand side Remove nuts and lockwashers from the three valve tie bolts item 29 amp 30 4 Remove the Valve end section item 22 Note there are shims between each section on the same side as the O Rings one shim per tie bolt do not lose them See Figure 1 5 Remove the flow control adjustment cable from the standard valve section and r
7. decrease in the amount of counterweight necessary The following table lists possible combinations of tire size weight of calcium chloride water solution and left rear wheel weights necessary to achieve the proper counterweight This table assumes the tire spacing is 8 ft 96 outside left rear tire 50 from tractor center line and right rear tire 46 from tractor center line or wider i Next P MISCELLANEOUS MODELS Continued Next Page 2004 Alamo Group Inc 1 9 Information Bulletin 061995 Continued from previous Page BOOM MOWERS Wheel Weights Pounds Tractor 18 4 30 Tire Size w 16 9 28 Tire Size w 16 9 24 Tire Size w 14 9 24 Tire Size w Weight 960 Ibs of Calcium 747 lbs of Calcium 654 Ibs of Calcium 507 lbs of Calcium lbs Chloride Mix 72 gal Chloride Mix 56 gal Chloride Mix 49 gal Chloride Mix 38 gal water to 360 Ibs water to 280 Ibs water to 245 lbs water to 190 Ibs Calcium Cloride Calcium Cloride Calcium Cloride Calcium Cloride X 400 400 350 300 250 200 150 100 50 0 0 0 865 A 820 A 770 A 720 A 675 A x KK KK KK OX x KKK KK KK KOK OK 630 A 580 A 530 A X Not recommended for mounting boom on tractor of this weight A No wheel weights are necessary The weight of calcium chloride water solution may be reduced to the amount in the brackets Note If your tractor is equipped with a tire size not shown contact the Alamo Industrial Engineeri
8. divided into two Sections Section Two Service Bulletins 1 Service Bulletin No Service Bulletins are listed by Bulletin Number Date Example the oldest Bulletin will be listed first and the most recent bulletin will be listed last Bulletin No 021004 first amp second digits are the Year the third amp fourth digits are the day of the month and the fifth amp sixth digits are the month this means the bulletin was written on Apr 10 2002 If more than one bulletin was written on that day the a dash with a number will added example 1 2 etc 2 Repairs Service Bulletins are intended to authorize only the repairs listed on It to be made under warranty or any other circumstance unless specifically instructed to do so 3 Parts This is the Rate at which compensation will be allowed under warranty for repair parts 4 Labor This is the amount of labor hours that are allowed to make this repair under warranty 5 Parts Disposition Service Bulletins listthe disposition of any parts that are removed during the repair If listed removed parts must be held awaiting return to factory if instructed to do so 6 Termination Date Service bulletins show a termination date this is the date that the Bulletin will be discontinued Any repairs must be made and all warranty applications filed by the listed date V All Service Bulletins printed in this Manual will void any previously printed Bulletin Any changes in these bulletins are the f
9. the Blade Carrier one bolt and Lockwasher atatime DO NOT remove all four bolts at one time and DO NOT INSTALL bilts that are longer or shorter than bolts that were removed 2 Replace one Bolt and Lockwasher torque it to 400 ft Ibs then move on to the next bolt 3 Continued this until all four bolts have been replaced Parts Required Part No Qty Description See Manual 4 Allen Head Bolt Blade carrier j See Manual 4 Lockwashers Spindle A Boom S N 06045 to 06071 B A S N 02534 to 02552 HY15 S N 02416 to 02418 HY60 S N 01211 to 01211 Machete S N 01360 to 01364 amp S N 02017 to 02036 MR60 S N 02035 to 02035 Torque to 400 ft Ibs Blade carrier retaining Versa S N 05175 to 05178 amp S N 06336 to 06394 Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial Warranty Policy Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 15 Figure 1 4 per carrier NOTES MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 16 INDUSTRIAL MISCELLANEOUS MODELS Technical Information Bulletin and Service Bulletin Manual Manual P N 0298 05 04 2004 Alamo Group Inc
10. to rear inside to outside because once you cut to size to match the existing Expanded Metal Screen they cannot be turned around Cutting these is permanent Installation Procedure 3 Use the measuring tape to get the measurements around your existing Expanded Metal Screen and write them down Note there is an Upper and Lower section See Figure 1 4 Place the Lexan Sheets Upper and Lower Sheets on a clean work suface and transfer your measurements from step 1 to the the Lexan Sheets using a Pen or other marker RE CHECK your measurement and when certain they are correct Cut the sheets out to match your measurements Lightly sanding the cut edges will smooth them out and round the outer edge slightly helping to protect it Sheets should look like sheets in Figure 2 note the holes will not be drilled in them yet MISCELLANEOUS MODELS Continued Next Page 2004 Alamo Group Inc 1 34 Information Bulletin 102103 Continued from previous Page 5 Securely clamp the cut Lexan sheets onto the expanded metal screen aligning the outer edges this can be done upper or lower sheet first Using a 3 8 drill bit drill the mounting holes through the lexan sheet in a pattern as in Figure 2 When drilling the holes in the Lexan Sheet use the drill to mark the metal frame of the expanded metal screen on all the holes When all the holes are drilled into the lexan sheet and marked into the metal frame remove the clamps and the lexan sheet 6 Usin
11. with the Alamo Industrial Warranty Policy Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 14 INDUSTRIAL SERVICE BULLETIN No 050504 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models A Boom Rotary Heads HY15 HY60 MR60 Machete Bulletin No Date Rotary Heads Rear Mount Rotary Heads Versa Rotary Heads kasko 050504 BA60 Heads May 5 2004 Labor Old Parts Disposition Termination Date 100 at Dealer Net 1 hr at Dealer registered Hold All Parts for disposi Aug 5 2004 Shop Rate tion under Warranty Policy Blade Carrier Retaining Bolts Subject Due to the Possibility of Bolts that may not meet Alamo Industrial Standard being used in the production process all bolts that meet the Serial Number list below should be changed This will apply to bolts that were used at factory during assembly process This WILL NOT include Bolts that were used as replacement parts If you have a model with the following serial numbers replace the bolts and Lockwashers Because there are more than one length of Bolt involved it will be required to use the appropriate Parts Manual to determine the Bolt and Washer Number that applies to your model Service Required 1 Remove the Four Allen Head Bolts in the center of
12. 011095 old 950001 Jan 10 1995 King Post Attachment Subject King post Attachment A great deal of confusion exist regarding replacement parts for Alamo Industrial King Post This bulletin should clarify which parts are currently being used in our King Post Assemblies Refer to the Operators Parts manual parts pages for exact part numbers The current King Post atthis time uses a Steel connex Bushing The bushings in the king post lift cylinder lug and turning arm are Teflon Chrome Plated Pins must be used with Teflon Bushings always Parts Item 1 2 MISCELLANEOUS MODELS Note An optional rear swing turning arm is available with a steel swing cylinder bushing however a greasable turning arm pin must be used with it Part No 02956821 02967171 02956830 02967397 02956831 02958345 02966767 02960458 02957008 02956882 02956941 02956818 02958636 02958637 02956838 02956839 Qty Description 1 King Pin w Bushing 1 Rear Turning Arm w Teflon Bushing ref Rear Turning Arm w Steel Bushing 1 Front Turning Arm w Teflon Bushing ref Front Turning Arm w Steel Bushing 1 Bushing Steel 1 Turning Arm Pin Chrome use w Teflon Bushing Only ref Turning Arm Pin Greasable use w Steel Bushing Only 2 Bearing Cup and Cone Assembly Ring Bottom Bearing Seal Ring Top Bearing Seal Bearing Support Collar Seal Seal Lockwasher Nut gt gt 2 Continued Next Page 2004 Alamo
13. Date Slopemower 121495 Dec 14 1995 Repair Procedure for Welding Cracks in Boom Heads If cracks appear in the welds at points A as shown above use the following procedures to repair head Parts Needed Part No Qty Description 02970111 2 90 Gusset 02970112 4 48 Gusset Welding Procedure Grind a groove at the site of the crack and clean the area to be welded Weld the crack making a 100 weld After repairing the cracks prepare the sites for installation of the gussets Position the reinforcing bar gusset part no 02970111 if 90 or part no 02970112 if 48 over the X Bar as shown in drawing next page Weld with a 1 4 fillet weld on the bottom and an edge weld on top DO NOT weld the ends 5 Clean and paint the area 6 Reassemble any parts that were removed MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 18 PON Continued Next Page Information Bulletin 121495 Continued from previous Page 48 Gusset 90 Gusset Note Do Not weld ends 1 4 NI TECHNICAL INFORMATION BULLETIN No 121495 Contact Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 Ph 830 372 2708 Fax 830 372 9603 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 19 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 011296 Alamo Industrial Technical Services Department 1502 East Wa
14. Group Inc 1 4 Information Bulletin 011095 Continued from previous Page Notice Serrated bushing shown Check which bushing you have inn Figure 1 Item Part No Qty Description 13 00606000 1 Cotter Pin 14 00752176 1 Grease Fitting 15 02965548 1 Bushing Teflon 1 1 4 OD 02957501 ref Bushing Steel 1 3 8 OD 16 02959225 1 Bushing 17 02965538 1 Main Pin Weldment Non greasable 02967490 ref Main Pin Weldment Greasable Parts If a customer orders a king post P N 02965545 with a solid steel bushing P N 02965536 and has an A boom or Versa Boom with a rear swinging boom he will be shipped a retro fit kit P N 02967237 For a Minute Man or Rear Mount boom they need P N 02968881 Kit TECHNICAL INFORMATION BULLETIN No 011095 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 5 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 012095 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models All Boom Mowers using Flail Axe Head Bulletin No Date 012095 Jan 20 1995 Pulley Fastening to Cutter Shaft of Flail Axe Head Subject A new method has been devised to secure the pulley to the cuttershaft A new pulley P N 02968712 and a QD Pulley Hub P N 00724670 has replaced the old pulley with setscrew washer lockwasher and bolt The new pulley and hub are a keyed taper lock d
15. No damage to bushing bore 20 Parts reguired for this Procedure 1 ea of P N 02969988 Retro Fit Kit Remove center pin and turning arm Pin 1 Move the swing cylinder out of the way Using a suitable driver remove the old bushing 2 and install a new bushing P N 02969987 Replace two bushings in the cylinder clevis 3 with P N 02959890 bushing use suitable driver Align cyl clevis with turning arm bore and install new P N 02960458 Pin and cotter pin Lubricate pin and test for proper operation Procedure Type 2 Slight damage to bushing bore Diameter does not exceed 1 3 8 gt 6 7 8 Parts required for this Procedure 1 ea of P N 02957501 Bushing 1 3 8 OD 1 ea of P N 02960458 Pin Turning Arm 2 ea of P N 02959890 Bushing 1 ea of P N 00606000 Cotter Pin Remove center pin and turning arm Pin 1 Move the swing cylinder out of the way If Bushing bore cannot be drilled in place the turning arm will have to be removed If so remove the turning arm from the king post See the Operators Service Manual for Turning arm removal Bore or drill the hole for the bushing to 1 3 8 Install the P N 02957501 1 3 8 OD Bushing using a suitable driver Reinstall the turning arm on the king post It may be advisable to replace the main pin bushing and or main pin at the same time Replace two bushings in the cylinder clevis 3 with P N 02959890 bushing use suitable driver Align cyl clevis with turning arm bore and ins
16. Pin Replacement MM 8 RB Blade Bolt Inspect Recall Bolt 02782900 BA New Holland T6640 8 T7740 A C Service Notice New Holland TS Tractor Inspection Service Notice Blade Bolt Inspection Recall Bolt 4 02782900 Blade Carrier Retaining Bolts INDEX 2 NOTES 2004 Alamo Group Inc SECTION 1 TECHNICAL INFORMATION BULLETINS This Book is divided into two Sections Section One Technical Information Bulletins Technical Information Bulletins Information Bulletins are listed by Bulletin Number Date Example the oldest Bulletin will be listed first and the most recent bulletin will be listed last Bulletin No 021002 first amp second digits are the month the third amp fourth digits are the day of the month and the fifth amp sixth digits are the year this means the bulletin was written on Feb 10 2002 If more than one bulletin was written on that day the a dash with a number will added example 1 2 etc Authorize Repairs Technical Information Bulletins do not authorize any repairs to be made under warranty or any other circumstance unless specifically instructed to do so Bulletin Reference Some Technical Information Bulletins will refer to the corresponding Service Bulletins for repairs and some are for information only Bulletin Instructions Technical Information Bulletins should have all the instructions as to what you need but may not have all the information needed to make an install
17. Shredders Bulletin No Date 011596 Jan 15 1996 Knife and Retaining Rod Replacement Procedure Subject The Cutter retaining Rod is a normal wear item and should be replaced when they show signs of excessive wear Under normal cutting conditions they can be reused through three to five cutter flail changes Use the following procedure when changing flail knives and retaining rod Procedure Note the position of each rod before disassembly this can be marked any way that is identifiable by you Remove all the cutter retaining rods bars and cutting flails knives as described in the maintenance section of the operators manual Reinstall each rod one position clockwise from the position it was originally installed For example if the rod was removed from position A see figure 1 then replace it into position B removed from position B is moved to position C and etc around the cutter shaft This will position the cutter flails over an unworn area on rods Figure 1 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 21 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 040896 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models All Models using Single Acting Hydraulic Cylinder Bulletin No Date 040896 Apr 8 1996 Oil Leaking from new single Acting Hydraulic Cylinder
18. Warranty Policy Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 2 INDUSTRIAL SERVICE BULLETIN No 930410 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models A Boom Versa Boom Versa Mower Boom Axe Bulletin No Date Slopemower and Interstater mounted on Ford 5640 6640 amp 7740 930410 i mounted prior to jul 16 1992 using front pump drivelines Old 93 008 Oct 4 1993 Labor Old Parts Disposition Termination Date 100 at Dealer Net 1 0 hr at Dealer registered No Returnable Parts Dec 5 1993 Shop Rate involved Pulley Adapter Spacers Ford 56 66 amp 7740 Tractors Subject Spacers used in driveline between Hub and crankshaft pulley change Spacers and bolts between hub and pulley on ford 5640 6640 and 7740 tractors need to be longer Service Required Note the 5640 uses different spacer and bolts 1 Remove the four retaining bolts from Hub where it mounts to Tractor crankshaft Pulley remove the 4 spacers P N 107620 Discard these spacers they will not be used 2 Using the existing 4 bolts P N 02965355 3 1 2 long and lockwasher P N 00022200 reinstall the hub using the new one piece spacer P N 02966404 6640 amp 7740 Models Only Note 5640 model tractor use Kit 02965750 instead of pa
19. ar tire filled with 960 pounds of calcium chloride water solution Use five pounds of calcium chloride per gallon of water 3 Improving Stability It is difficult to send out a standard counterweight package which works well on all tractors due to the many makes and models used for boom machines At times it may be necessary to add wheel weights in addition to the standard practice of adding a full charge of calcium chloride to the left rear tire and spreading the rear tires to a minimum to 96 if possible itis also advantageous to spread the rear tires to wider than ti minimum 96 Tire Spacing The rear tire spacing of the tractor is very important As the tire spacing is narrowed it reduces the effectiveness of the tractor weight and wheel weight in counter balancing the boom Therefore any spacing narrower than the 8 ft 96 previously referred to will require more application where tire spacing is less than 8 ft Boom Extension As the boom length at maximum extension is decreased the amount of counterweight necessary for balancing the unit is reduced This is accomplished by relocating the boom stop The factory should be consulted on application where this method is used Tractor Weight Tractor weight is extremely important to the balance of the unit The left rear tire tends to tip upward and therefore any weight to the left of the right rear tire acts as a counterweight tractor included An increase in tractor weight will allow a
20. ation complete In some cases it may be required to refer to other manuals for more complete information this should be suggested in the Technical Information Bulletin All Technical Information Bulletins printed in this Manual will void any previously printed Bulletins Any changes in these bulletins are the final version as of the date of this manual MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 1 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 081594 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Interstaters in Frame Colling Versa pro Grounds Keeper Bulletin No Grass King amp Hydro 88 081594 Date Aug 15 1995 old 940012 Motor High Pressure Seal Kit Subject There is a high pressure shaft seal kit available for the piston motors used on above products kit P N 02966926 If the shaft seal has been blowing out replace with this kit Note the new motors shipped in the future will have this high pressure seal already installed Disassembly Work in clean area cleanliness is extremely important when repairing hydraulic components Before disconnecting any thing clean the entire motor area your work area and your tools of any de bris that might get into the system Disconnect and plug hydraulic lines remove motor from the mower Cover the spindle where motor was removed to keep it clean Thoroughly clean the outside of the motor drain any oi
21. bes the assembly in detail will be shipped if a new coupler is Hub ordered this bulletin is to in form you of the design change see Figure 1 If there are further questions please con tact Alamo Industrial s Techni cal Service Department Flexible Coupler Pulley Sheave Figure 1 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 31 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 101802 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models All EKII Hydro 60 Hydro 72 All Machete All A Boom All i j Bull No Date Versa All Rear Mount All Slopemower All Brahma 8 All Hydro 15 eo All Hydraulic powered Rotary Mower heads that utilize the 101802 Oct 18 2002 F 02960553B 02960553C and 02968859A Spindle Assemblies RA Spindle Bearing Lubrication Update Normal maintenance of the 02960553B 02960553C and 02968859A Spindle assemblies has included the addition of NLGI 000 grease to provide proper lubrication of the bearing assemblies Due to repeated customer requests this lubrication requirement has been changed to NLGI EP 2 Lithium Wheel Bearing Grease Implementation of this grease will allow Spindle Assembly Vent improved lubrication especially to the top bearing Plug as well as substantial improvement of the daily N A FX mainte
22. ce repairs The most common service parts are pumps and motors will now be available for order through Alamo Industrial Customer Service Department Likewise a parts breakdown with Alamo Industrial part numbers will be provided The Eaton Pumps and Motors Danfoss Control Valves will be the first components available with such a parts breakdown It is Our intention to provide a better and more reliable service parts system This transition will better suit customer and provide more timely and efficient parts delivery This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 30 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 041101 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models All Alamo Industrial Products using the Buzz Bar Head are affected Bulletin No Date 041101 Apr 11 2001 Buzz Bar Drive Coupling Design change There has been a design change to the drive coupler assembly for the Buzz bar Cutting Head If a flexible cou pler Alamo Industrial P N 02974245 for Machete or P N 02974246 for A Boom amp Slopemower are ordered they will be a different design The new flexible coupler design will be molded rubber with metal inserts The new molded rub ber version will directly replace the machined design using the same part number An instal lation drawing that descri
23. chnical Information Bulletins printed in this Manual will void any previously printed Bulletin Any changes in these bulletins are the final version as of the date of this manual Section Two Service Bulletins 1 Service Bulletin No Service Bulletins are listed by Bulletin Number Date Example the oldest Bulletin will be listed first and the most recent bulletin will be listed last Bulletin No 021004 first 8 second digits are the Year the third 8 fourth digits are the day of the month and the fifth amp sixth digits are the month this means the bulletin was written on Apr 10 2002 If more than one bulletin was written on that day the a dash with a number will added example 1 2 etc 2 Repairs Service Bulletins are intended to authorize only the repairs listed on It to be made under warranty or any other circumstance unless specifically instructed to do so 3 Parts This is the Rate at which compensation will be allowed under warranty for repair parts 4 Labor This is the amount of labor hours that are allowed to make this repair under warranty m Parts Disposition Service Bulletins list the disposition of any parts that are removed during the repair If listed removed parts must be held awaiting return to factory if instructed to do so 6 Termination Date Service bulletins show a termination date this is the date that the Bulletin will be discontinued Any repairs must be made and all warranty applications filed by the lis
24. e front mower is not leveled as described above the amount of vertical movement available for the front mower when higher terrain is encountered is severely restricted resulting in binding and bending or breakage of the a frame and mount plate weldments The front mower must be re levelled each time the cutting height is changed Top Link Figure 1 Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial Warranty Policy Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 9 INDUSTRIAL SERVICE BULLETIN No 953011 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Date Bulletin No 17 20 amp 23 A Boom Versa Boom Rear Mounted Boom aaa a 15 8 17 Minute Man Boom Old 950016 Nov 30 1995 Labor Old Parts Disposition Termination Date 100 at Dealer Net 0 7 hr at Dealer registered Scrap removed parts Jun 1 1996 Shop Rate Dipper Cylinder Pin Replacement Subject Replace Old Pin P N 02966936 dipper cylinder pin with New Pin P N 02969980 P N 02030300 Nut and P N 00749946 Washer Mowers equiped with 02966936 dipper pin old pin can be identfied by absence of a nut on the end of the pin Service Required 1 Rest Head o
25. ee New Holland Service Sep 30 1999 Service Bulletin 399 Bulletin 399 New Holland T7740 amp T6640 A C Drier Campaign Subject In order to increase customer satisfaction New Holland is providing a new Air conditioner Receiver Drier Kit for the S N units detailed in new Holland Service Campaign 399 The specifics to this bulletin are provided by the New Holland Bulletin The purpose of this bulletin is only to inform you of the work that needs to be done per New Holland Bulletin and not to authorize any work on the behalf of Alamo Industrial or any of their affiliated companies If in Question you should consult your New Holland Dealer for details of repairs Units Serial Numbers Model T 7740 084228B 084349B 084350B 084352B 084359B 084476B 084549B 084550B 084570B 084571B 084599B 084627B 084629B 084632B 084633B 084635B 084636B 084647B 084648B 084652B 084661B 084800B 084850B 084964B 084966B 084967B 085607B 086462B 086470B 086471B 086472B 086503B 086504B 086505B 086589B 086648B 086649B Model T6640 084230B 084351B 084411B 084412B 084526B 084529B 084816B 084818B 084832B 084833B 084834B 084847B 084849B 084963B 084965B 086484B 086485B 086486B 086487B 086488B Service Required See New Holland Service Campaign 399 for Service details Parts Required See New Holland Service Campaign 399 for Parts requirements Special Note This Service Bulletin does not authorize any repairs on behalf of Alamo Industrial its strictly to inform you
26. emove the section Turn the spool until the setscrew is accessible 6 Install O Rings in the new Float Valve Section using a small amount of white lithium grease to hold them in place Transfer the spool control link from the Standard Valve Section to the new Float Valve Section Figure 1 Reinstall Modified Valve 1 Reinstall float valve section in place of standard valve section in reverse of removal making certain there is one shim on each tie bolt between each section Make certain all O Rings are in place keep close watch on O Rings to make ceratin none fall out during assembly 2 Install flow control cable before installing end section Flow control spool should be set at the minimum setting all the way clockwise The flow control knob in cab should also be turned to the minimum setting Securely tighten the setscrew Continued Next Page MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 5 Service Bulletin 930510 Continued from previous Page 3 Replace the end section and snug up nuts on the tie bolts 4 Install the Valve assembly support bolt Tighten until snug without any looseness Do not over tighten or the valve may distort 5 Tighten the tie bolts nuts to 20 22 ft Ibs tighten them in alternating pattern so that they valve is compressed evenly 6 Reinstall all hoses to the correct ports install spool control link to the shaft arm Removal of Detent Spacer 1 Remove detent assembly item 28 from detent
27. esign which will provide a better fit and longer service life for the shaft Hub P N 00724670 Pulley P N 02968712 Figure 1 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 6 NOTES MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 7 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 061995 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Bulletin No Date Jun 19 1995 Slope Mower Boom Axe Balance 061995 old HIB 61995 4 Boom Balance Recommendations Introduction To insure the safety of the operator against instability of the tractor it is crucial that the left rear tire of the tractor exert a minimum force weight of 1 000 pounds on the ground when the boom is at full extension and the cutter head is horizontal and two feet off the ground Figure 1 An installation not meeting this requirement is dangerous and should not be operated as overturning the unit can occur resulting in injury or death An installation meeting this requirement allows operation of the unit on slopes not exceeding 5 For operating on slopes greater than 5 contact Alamo Industrial Technical Service Dept for additional information The head and boom must be resting on the boom rest or the ground prior to removing or repairing Left rear Tire Location of Balance Weight Level Grou nd Fig
28. g a 1 4 Bit drill the holes into the frame of the expanded metal screen with the Lexan removed Note you drilled 3 8 holes in the Lexan and 1 4 holes in the frame work This is so that the Lexan will not have a binding fit 7 Install the Bolts as shown in Figure 3 1 st bolt through frame 2 nd install the fender washer 3 rd remove the protective cover sheet from the inner side and install the Lexan sheet 4 th install the Flatwasher 5 th start the Locknuts B Upper onto the bolts but do not tighten them 8 Once allthe bolts washers and nut are installed begin to tighten them DO NOT over tighten these Locknuts and put the Lexan sheet ina bind which will crack it Tighten the Nuts evenly and only snug them so the Lexan sheet will not move Do this with the upper and lower Sheet Then remove the protective cover from the outside of the sheet Lower Expanded Figure 1 Metal Screen Fender Washer Expanded l Metal Lexan Shield Screen Flatwasher Locknut Bolt Lower Lexan Sheet Bolt Lexan Shield to Expanded Metal Screen Cut Lexan Figure 2 Shields Figure 3 TECHNICAL INFORMATION BULLETIN No 102103 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group lnc 1 35 NOTES MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 36 SECTION 2 SERVICE BULLETINS This Book is
29. in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 7 INDUSTRIAL SERVICE BULLETIN No 940106 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models A Boom Versa Boom Rear Mount Mower Minute Man Bulletin No Date 940106 Old 940007 Jun 1 1994 Labor Old Parts Disposition Termination Date 100 at Dealer Net 0 7 hr at Dealer registered No Returnable Parts Aug 1 1994 Shop Rate involved Swing Cylinder Bushing amp Pin Replacement Subject Premature wear of teflon coated swing cylinder bushing To replace the swing cylinder bushing on unit built prior to June 1994 if premature wear in swing cylinder bushing occurs Service Required 1 With Boom Arm extended outward and Head resting on the ground Tractor secured in a safe manner You will not have to remove any hydraulic lines to perform this repair 2 Remove Swing cylinder pin this is the old pin that connects it to the turning arm The swing cylinder will pull away from turning arm far enough that only this end needs be disconnected 3 Using a suitable driver remove the old bushing from the turning arm 4 Check the condition of the bore in the turning arm if damaged repair or replace turning arm 5 Install new bushing P N 02965548 using a suitable driver Slide cyl
30. inal version as of the date of this manual MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 1 INDUSTRIAL SERVICE BULLETIN No 922909 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models A Boom Versa Boom Versa Mower Boom Axe Slopemower and Interstater mounted on Ford 5640 6640 amp 7740 mounted prior to jul 16 1992 using front pump drivelines Bulletin No Date 922909 Old 92 009 Sep 29 1992 Labor Old Parts Disposition Termination Date 100 at Dealer Net 1 0 hr at Dealer registered No Returnable Parts Nov 30 1992 Shop Rate involved Pulley Adapter Mounting Bolts Ford 56 66 amp 7740 Tractors Subject 7 16 bolts holding Hub to Tractor Crankshaft Pulley found to need more engagement into pulley longer bolts required Service Required 1 Remove the four retaining bolts from Hub where it mounts to Tractor crankshaft Pulley The old bolts were 3 1 4 long P N LHOB128B the new replacement bolts need to be 3 1 2 long P N 02965355 longer bolts 2 Use locktite on new bolts and install them into the hub and pulley tighten the bolts to retain hub to crankshaft pulley 3 Run and test for operation Parts Reguired Part No Qty Description Pulley Hub 02965355 4 Bolts 3 1 2 long Retaining Bolts Figure 1 Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial
31. inder back and align the holes insert the new chrome pin P N 02966767 install the cotter pin P N 00606000 6 Run and test operation of unit Parts Required Part No Qty Description 02966767 1 Chrome Pin 02965548 1 Bushing 00606000 1 Cotter Pin Turning Arm Chrome Pin Cotter Pin Bushing Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial Warranty Policy Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 8 INDUSTRIAL SERVICE BULLETIN No 941710 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Versa Pro Flail Bulletin No Date 941710 Old 940019 Oct 17 1994 Old Parts Disposition Termination Date 100 at Dealer Net 0 0 hr None No Returnable Parts Dec 30 1994 involved Leveling Center Mower Subject Leveling front center mower to prevent damage to the linkage between the main frame and the center mower due to improper leveling of the center unit Service Required Level front mower by adjusting top link being sure shoes are level with ground When leveled check the front caster wheels If the unit was leveled properly the wheels should be two to four inches above the ground Important If th
32. l left in mount into proper container Remove original retaining ring from motor housing Pry original shaft seal from the housing take care not to damage shaft or housing Remove original washer from housing Assembly Lubricate new seal adapter O ring and fill the snap ring groove Original Shaft Seal in motor housing with lithium based 2 grease Install O Ring and shaft seal into the adapter Seallip Original should face shoulder of adapter Retaining Install adapter in motor housing Ring with shaft seal side into housing first by pressing it into place with finger pressure Light tapping may be used however be careful not to cock the adapter as it is pressed by the snap ring groove as this would cause O Ring damage Install the Z Shaft Seal 02966922 new retaining ring Reinstall motor on machine Run and test Seal Adapter 02966923 Original Washer Seal Kit for operation Figure r Retaining Ring 02966925 02966926 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 2 NOTES MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 3 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 011095 Models 15 8 17 Minute Man 17 20 amp 23 RMB 17 20 23 28 A Boom 17 20 amp 23 Versa Boom Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Bulletin No Date
33. le Update BA DODO AAA APA 08 08 97 McConnel Boom Flail Specifications McConnel 031000 1 28 03 10 00 TS Tractor Fuel Filter Change New Holland OOO PR PR 1729 AA 08 03 00 Spindle Oil Filler Kit Rotary Head DADO POS TBO atras 04 09 01 Rebuilt Parts Availability Change Notice All A TES sin o 04 11 01 Buzz Bar Head Drive Coupler Change All TOO nan AA 10 18 02 Spindle Bearing Lubrication Change All 102109 AA jE AA 10 21 03 Lexan Shield Availability Non Cab Tractors All 2004 Alamo Group Inc INDEX 1 INDEX MISCELLANEOUS MODELS Models With Few Bulletins Section 2 Service Bulletins Bulletin No Old No Page O nn ers 922909 92 009 sico DE ita 930410 93 008 20 RAN 930510 93009 Z ee eee 942801 940005 DE A OVP 940106 940007 WW 953011 970108 992704 991911 030702 2004 Alamo Group Inc 990005A 2 13 1020703 2 14 050504 DAB caido 941710 940019 2 9 Description Service Bulletin Introduction Crankshaft Pulley Adapter Spacers 56 66 7740 Crankshaft Pulley Adapter Spacer 56 66 7740 Implement Control Valve Modification VP Mechanical Float Kit VP Swing Cyl Bushing amp Pin Replacement MM 8 RB Leveling Center Mower VP Dipper Cylinder
34. lizing the quick connect fittings remove the vent plug and pump in the oil untill oil is seen at the vent plug opening reinstall the vent plug and remove the bottle at the quick connect fitting The female quick disconnect is designed to be left on the spindle in place of the fill plug Utilization of this spindle fill kit should decrease maintance time and failures by providing accurate oil fill of the spindle assembly Hose with clamp Female Quick Connect Spindle Assembly Oil tank Figure 1 with Hand Pump This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 29 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 040901 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models All Alamo Industrial Products are affected Bulletin No Date 040901 Apr 9 2001 Change in the availability of rebuilt components This bulletin has been published to inform you of a change in the availability of rebuilt parts In the past rebuilt components such as pumps and motors were available for use as spare parts That will no longer be the case The major factor in this decision was the lack of cores that are returned from the customer Since Alamo Industrial will no longer offer rebuilt parts an effort will be made to offer customers a complete parts listing of all components that are needed as servi
35. lnut Seguin Texas 78155 830 372 2708 Models All Hydraulic Units using P N 00768991 Speed Increaser Bulletin No Date 011296 Jan 12 1996 New Sealing Washers Used on Plugs of Speed Increaser Speed Increaser Assembly P N 00768991 Plug Seal Update There have been some isolated reports of the case plugs backing out on the above mentioned Speed Increasers causing loss of oil and cataastrophic failures of the gearbox Test conducted by Alamo Industrial revealed when ambient temperatures exceeded approxi mately 100 F the nylon and plastic washers on the plugs would get soft or melt this allowed the plug to back out We have contacted our supplier of these parts and had the material specifications changes for these washers The new washers are made of aluminum istead of the old nylon or plastic The part number for the washers P N 00754536 and 00755424 will remain the same as there will be no changes in the way they fit only in the type material they are made out of All units operating in warm temperature of 100 F or higher should be changed right away to prevent plugs from backing out Figure 1 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 20 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 011596 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models FM Severe Duty
36. lve Seal Kit Subject New Seal Kit used on Logic Valve Assembly P N 02971267 In early 1996 changes were made to the Logic Valve used in the P N 02960565 motor control valve used on a number of machines The change were made to improve the service life of the seals The seal grooves on the logic valve were widened and the backup rings were added to both O Ring Seals The Seal Kits were also changed to include the Back Up Rings the three O Rings remained the same When using the Seal Kits to reseal the former Valves the seal grooves are not wide enough to accept the O Rings and the Back up Rings The Back Up Rings will have to be discared and not used Parts Needed Qty 1 of P N 02961268 Seal Kit O Rings and two split Teflon spacers are include Procedure in Kit 02961268 follow the directions included with O Rings and two split Teflon the Logic valve Seal Kit As the split back up rin spacers are include in Kit 02961268 may not be needed follow the directions included with the Logic valve Seal Kit As the split back up rings may not be needed This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 24 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 071897 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models AllBoom Axe Mowers A Boom Versa Boom Bulletin No and Slopemower 071897
37. n the floor or ground with dipper cylinder accessible Make certain all hydraulic pressure is relieved from Hoses and cylinder system 2 Secure and support dipper with hoist to prevent movement when pin to dipper cylinder is removed 3 Replace the original pin P N 02966936 with the new pin P N 02969980 nut P N 02030300 and washer P N 00749946 4 Tighten Nut and retaining bolt Remove Hoist from dipper 5 Run and test for operation Parts Required Part No Qty Description 02969980 1 Dipper Cyl Pin 02020300 1 Nut 00749946 1 Washer Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial Warranty Policy Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 10 Figure 1 INDUSTRIAL SERVICE BULLETIN No 970108 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Boom Axe 50 S N 01112 8 up 60 S N 01167 amp up Bulletin No Versa Mower 60 S N 04438 8 up 72 S N 04401 amp up Slope 979108 Mower head S N 01020 amp up Machete rotary head S n 01039 amp Old 970009A Aug 1 1997 Labor Old Parts Disposition Termination Date 100 at Dealer Net 1 0 hrs at Dealer registered Scrap Old Parts Aug 31 1997 Shop Rate
38. nance reguirements A pa A s Eis i gt gt Conversion S 1 Remove the existing fill plug from the spindle housing and discard it this is the lower plug in figure 1 2 Install a standard 1 4 fine thread grease zert into the fill plug port as shown in figure 1 Figure 1 3 Remove the Vent plug Top plug in figure 1 4 Fill the housing with NLGI EP 2 Lithium Grease or equivalent from a standard grease gun until the new grease is seen in the vent plug hole Approximately 2 standard grease tubes will be required when Spindle Assembly is empty 5 Clean off any excess or over flow grease and reinstall vent plug 6 Maintain proper lubrication with 5 pumps of grease into the spindle every 8 hours of use This will keep the Spindle bearings lubricated 7 Always clean excess Grease away from Spindle after greasing Spindle This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 32 NOTES MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 33 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 102103 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models All Non Cab Models with Expanded Metal Side Screens Bulletin No Date Retro Fit Kit P N 02980005 102103 Oct 21 2003 Lexan Polycarbonate Shield Upgrade Kit P N 02980005 field Install Alamo I
39. ndustrial has designed a Lexan Polycarbonate Shield that will install on the expanded metal screen currently used on the Non Cab models This is a retro fit kit that is designed to be customer installed over the expanded metal screen The Lexan Sheets will require trimming and the Holes will have to be drilled in the Lexan sheets as well as through the existing expanded metal screen frame Recommended Tools 1 Jig Saw or Circular Saw hand held or table equipped with plastic cutting blade 2 Electric Hand Drill preferably a variable Speed Drill 3 3 8 and 1 4 High Speed Steel Drill Bit Drill bit should be sharp and in good condition 4 Measuring Tape or other measuring device 5 Hand Wrenches for tightening Bolts do not use air tools to tighten bolts 6 Straight edge and marker that will write on Lexan Lexan Shield Kit Components Retro Fit Kit P N 02980005 includes PartNo Qty Description Part No Qty Description 02980003 1 Lexan Sheet Upper 02970004 1 Lexan Sheet Lower 0461600 20 Bolt Hex Head 1 4 20 00024100 20 Flatwasher Std 1 4 02980068 20 Fender Washer 1 4 32901C 20 Locknut 1 4 20 Protection of Lexan Sheets 1 Do not remove protective sheet Paper from the Lexan Sheet This will protect it while you are working with it You can drill through this protective sheet as well as cut through it 2 There are two Lexan Sheets sent an upper and a lower Identify these and mark them to designate front
40. ng Department for assistance in determining the amount of counter weight you will need Continued Next Page MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 10 Information Bulletin 061995 Continued from previous Page Tire Balance for Booms Specifications Rear Tire Pressure and Permissible Loads the following chart gives the carrying capacity of the axle at the pressure indicated Inflation Pressures Ibf in u tut mjr To Te TA SN IT E E fps ua ff ez jus Foren foro an so for asas so ros o 16 9 14 34 6 8070 8470 8880 fem oe je re ssd amas set eon iso OBCI oes e js le p 18 4 15 30 9350 le aa e fes i yy egy E 9920 10410 10870 11310 11925 12230 12695 13180 When mounted implements are used rear tire loads may be increased by up to 20 with no increase in inflation pressure when operaterd at speeds not to exceed 12 MPH The above table is for guidance only For exact information regarding inflation pressures and loads for your particular tires consult your authorized tractor dealer TECHNICAL INFORMATION BULLETIN No 061995 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 11 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 092895 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models
41. of New Holland Service Campaign 399 Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial Warranty Policy Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 12 INDUSTRIAL SERVICE BULLETIN No 991911 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models All New Holland TS Tractors w Cabs amp S N less than Bulletin No 115012B date code 8L18 plus All New Holland TS Tractors with 991911 i or without Cab 8 S N less than 110026B date code 8j09 Old 990005A Nov 19 1999 Labor Old Parts Disposition Termination Date 100 at Dealer Net O hr see New Holland see New Holland Service Apr 30 2000 Service Bulletin 409 Bulletin 409 New Holland TS Tractor Inspection Campaign Subject In order to increase customer satisfaction New Holland is reguesting inspection of some tractors See S N s listed below detailed in new Holland Service Campaign 409 The specifics to this bulletin are provided by the New Holland Bulletin The purpose of this bulletin is only to inform you of the work that needs to be done per New Holland Bulletin and not to authorize any work on the behalf of Alamo Industrial or any of their affiliated companies If in Questi
42. of the Cylinder and its components This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 22 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 042996 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models All New Holland Tractors with Alamo Industrial Mounted Booms Bulletin No Date 042996 Apr 29 1996 Dead Batteries on New tractors There have been several reports recently of dealers receiving machines with dead batteries some of which could not be satisfactorily recharged Please see the attached copy of a tag which is coming with the new tractors The small electrical discharge being mentioned amounts to a constant drain on the battery Ifthe battery cable Post is left connected for along enough time with the tractor inactive the battery will become sulfated permanently damaged and will not accept a charge Sulfated batteries are not warranted through the battery manufacturer At present the only alternative to removing the battery cable would to be install a battery disconnect switch in the negative cable which would allow the battery to be easily isolated These switches are available at most major tractor dealers USE CAUTION when installing any thing on battery cables disconnect the positive cable before installing disconnect switch and make sure after switch is installed tha
43. olicy Blade Bolt Inspection Subject Quality inspections revealed the potential for cracking of the Blade Bolt Cracks are the result of manufacturing procedures and will be present on the bolts prior to installation on the mower This is pertaining to a Date code which is stamped on the threaded end of the bolt Date Code 11 02 Service Required 1 Inspect all Bolts in Parts stock and those on the effected mowers by checking the dated code on the Blade Bolt 2 If Blade Bolts do not have the 11 02 date code no service will be required 3 If the Date code 11 02 is there check the Bolt for any cracks in them If the bolts are installed on the mower they will have to be removed to check 4 If they check OK reinstall them and torque them to 600 ft Ibs and reinstall roll pins 5 If they have cracks replace them with new ones install the new bolts and torque to 600 ft Ibs Reinstall roll pin Date Code Parts Required Stamped on this Part No Qty Description end 11 02 02782900 alr Blade Bolt Alamo Logo 8 Nov 2002 Part No Note Always check Date Code and Stamped on Part Number of blade bolt before Head End performing any repairs as described P N 02782900 in this Service Bulletin as not all Blade will have the same date code Only Blade bolts with 11 02 date code will be considered for warranty consideration Figure 1 Warranty Compensation will be provided following proper filing of warranty claim in accordance
44. on you should consult your New Holland Dealer for details of repairs Units Serial Numbers All New Holland TS Tractors w Cabs amp S N less than 115012B date code 8L18 plus All New Holland TS Tractors with or without Cab amp S N less than 110026B date code 8j09 Service Required See New Holland Service Campaign 409 for Service details Parts Required See New Holland Service Campaign 409 for Parts requirements Special Note This Service Bulletin does not authorize any repairs on behalf of Alamo Industrial its strictly to inform you of New Holland Service Campaign 409 Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial Warranty Policy Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 13 INDUSTRIAL SERVICE BULLETIN No 030702 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Rotary Heads using Blade Bolt No 02782900 Bulletin No with Date Code on Bolt of 11 02 amp 02782900 Blade Bolts in Parts 030702 Old 1020703 Feb 7 2003 Stock with the 11 02 date code Labor Old Parts Disposition Termination Date 100 at Dealer Net Will be evaluated on a case Hold All Parts for Return Apr 15 2003 by case basis under Warranty P
45. orces on the cylinder mounting lugs on the mainframe Read all directions completely before beginning any repairs as there are somethings that are do not do listed in instructions Service Required The Detent valve needs to have a detent spacer removed from valve section in order to have float Standard Valve Section needs to be removed and replaced with a float valve section P N 002495 Ford P N 9703919 See following steps for installation Tractor Preparation 1 Locate the tractor on a level floor where an overhead crane can be used to raise the cab Put 3 4 pipe plug in filler neck of hydraulic reservoir and tighten to prevent air entry into reservoir Install the articulation lock pin Put forward reverse lever in neutral and set parking brake 2 Use a suitable floor jack to raise right hand cab end wheel assembly off the floor Remove wheel assembly and set it aside Note reference to right hand left hand side is viewed from operators seat facing forward Place a 2500 Ib or more capacity jack stand under the right hand side to support tractor where wheel was removed 3 Support the right hand side of the cab with a hoist attached to a chain which is hooked into the hole in the cab frame for the heater hose Remove the nuts and lockwashers from the right hand cab supports and take the weight off the bolts with the hoist Note If a hoist is not available the cab can be raised with a jack Be careful when using a jack as it can slip
46. re designed using metric standards The metric units have been converted to gallons and pounds per square inch so they are easier for our customers and dealers to use The flow and pressure figures provided can be used when comparing specifications and for answering questions from prospective customers To avoid rotor shaft vibration special attention must be paid to the note below concerning tractor engine speed and the resulting Power Take Off shaft revolutions per minute RPM Flail Rotor Speed Note the recommended rotor speeds is a maximum of 2500 RPM which is obtained at 490 RPM PTO Speed on all products except the PA 91 The PA 91 rotor is balanced to operate at 2475 RPM which is obtained at 450 RPM PTO speed Operating the McConnel Flail Units at 540 RPM PTO speeds will drive the rotors at 2755 RPM on all units except the PA 91 which will turn 2970 Rotor RPM at 540 PTO RPM If the McConnel units are operated at this high PTO RPM harmful vibration may develope at high rotor speeds and damage unit When operating the McConnel units it is required that you compute what engine speed is needed to operate the PTO at the require speed of 490 PTO Speed except for the PA 91 which requires 450 PTO RPM Horse Power Calculations To calculate the horsepower required to operate any hydraulic system GPM times PSI times 0 00058 This calculation requires US Gallons not imperial Gallons Continued Next Page MISCELLANEOUS MODELS 2004
47. rts listed above in step 2 the kit will include spacer and four new 4 bolts for the 5640 model Tractor The Old 4 Piece procedure will be the same but Spacers the parts will be different Pulley Hub Parts Required 6640 amp 7740 Part No Qty Description 02965355 4 Bolts 3 1 2 long 02966404 1 Spacer 4 hole Retaining Bolts Parts Required 5640 SAL Crankshaft Pulley Part No Qty Description 02965750 1 Spacer Kit Replaced by a one piece four hole spacer Figure 1 Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial Warranty Policy Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 3 INDUSTRIAL SERVICE BULLETIN No 930510 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Versa Pro Flail Mounted to a Ford Versatile 9030 Tractor Bulletin No Date 930510 Old 93009 Oct 5 1993 Old Parts Disposition Termination Date 100 at Dealer Net 0 hrs No Hours allowed No Parts Dec 31 1993 Implement Control Valve Modification Subject Implement control valves used to raise and lower wings needs to be converted to Float style valve This is to allow wings to freely move or float up and down without causing excessive f
48. s Please continue using the 87801634 filter when replacing the fuel filter on the TS Series tractors equipped with the Alamo Industrial products Alamo Industrial attachments do not stress or Work the tractor engines in a manner that would be considered extreme service The part 87801434 fuel filter will provide adequate protection when the engine of a TS Series New Holland tractor is powering Alamo Industrial Side or Boom Mounted products This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 28 TTT RAM TECHNICAL INFORMATION BULLETIN No 080300 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models All Machete A Boom Versa Rear Mount Slopemower j i l i Bulletin No Date Brahma EKII Hydro 60 Hydro 72 amp Hydro 15 ulletin No All Hydraulic powered Rotary Mower heads that utilize the Aug 3 2000 02960553B 02960553C and 02968859A Spindle Assemblies 0 dci Spindle Oil Filler Kit P N 02976501 ASpindle oil filler kithas been developed to provide accurate an easy fill of oilinto the spindles used on all hydraulic powered mowers The Oil filler Kit P N 02976501 is available through Alamo Industrial Parts dept Installation requires the replacement of the fill plug with the female quick connect fitting To fill the spindle attach the hose and oil bottle to the spindle by uti
49. s There have been numerous cases of the dealers and customers replacing single acting hydraulic cylinders on new machines due to oil leakage out of the vent plug in the cylinder In many of these instances no defect could be found in the cylinders Further investigation has revealed that he manufacture of our cylinders is leaving oil in the cylinders after their testing The Oil is left to help protect the interior of the cylinders during storage When the cylinders are fully actuated they are forcing this oil out the vent plug causing what appears to be a leaking cylinder through the vent plug Even the oilis cleaned off the cylinder after testing there is enough oil still inside the cylinder to bleed out when used If you have a New Cylinder that appears to be leaking from the vent plug The oil should be cleaned off and unit ran for a few days to a week to determine if the Cylinder is leaking or if it is the oil that was left in the cylinder to protect it It has been found that in some cases it has taken as much as a week for this to appear that it is not leaking Ifafter running and cycling the cylinder during operation and the cylinder continues to leak then the necessary repair should be performed Cylinders that are attracting dust around them is not considered to be leaking This dust collecting around them is considered normal All Cylinder that are returned as leaking will be pressure tested for leakage to determine the condition
50. sed on damaged frame if the frame can be straightened and is structurally sound Instructions and decals are included in the kit as well as the plate weldment that is to be installed Parts Needed Qty 1 of P N 02969710 Frame Reinforcement Kit Procedure The repair procedure is shown in instruction sheet P N 02969709 Top amp Bottom of Plate Figure 1 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 14 NOTES MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 15 TTT REM TECHNICAL INFORMATION BULLETIN No 121295 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Rear Mounted Boom A Boom and Versa Boom Bulletin No Date 121295 old 1212 Dec 12 1995 Convert Turning Arm to Greasable Steel Bushing Subject The Current production Booms are equipped with Teflon Bushings and Chrome Pins at the Swing Cylinder Turning Arm connections Some customers prefer greasable joints Use the information provided in this bulletin to convert to a greasable steel bushing arrangement There are three procedure types methods of repair that can be used The method used depends on the condition of the bushing bore A on the turning arm All procedures start with the mowing Head at rest on the floor Ground and all Hydraulic pressure relieved from system Procedure Type 1
51. t it is OFF before reconnecting Positive Cable ATTENTION BATTERY CARE Your new Tractor has electronics which cause a very small electrical demand on the battery If the tractor in not in use for an extended period disconnect battery to avoid damage by excessive discharge Recharge Battery if voltage is less than 12 3V S G less than 1 140 Lataa Akku uudelleen jos jannite on alle 12 3V ominaispaino alle 1 140 Ricaricare la batteria se il voltaggio e inferiore a 12 3V G S inferiore a 1 140 Batteria recarregavel se a voltagem for inferior a 12 3V Gravidade especifca inferior a 1 140 Laddt de batterijweer op wanneer de voltage lager is dan 12 3V S G Minder dan 1 140 Recharger la batterie si la tension est inferieure a 12 3V Densite inferieure a 1 140 Batterie wieder aufladen wenn spanning unter 12 3V Spez gewicht unter 1 1 40 IST Recarcar la bateria si el voltage es inferior a 12 3V S G inferior a 1 1 40 Batteriet ma lades opp hvis spenningen er mindre enn 12 3V Spesifikk vekt under 1 1 40 Part No 82001815 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 23 INDUSTRIAL TECHNICAL INFORMATION BULLETIN No 100296 1 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models All Mowers Using P N 02960565 Bulletin No Motor Control valve 100296 1 Date Oct 2 1996 Logic Va
52. tall new P N 02960458 Pin and cotter pin Lubricate pin and test for proper operation Continued Next Page MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 16 Information Bulletin 121295 Continued from previous Page Procedure Type 3 Bushing bore worn more than 1 3 8 Parts required for this Procedure 1 ea of P N 02956830 Rear Turning Arm or 1 ea of P N 02956831 Front Turning Arm 1 ea of P N 02960458 Pin turning Arm 2 ea of P N 02959890 Bushing 1 ea of P N 00606000 Cotter Pin Remove center pin and turning arm Pin 1 Move the swing cylinder out of the way remove turning arm from king post Replace Turning Arm with new turning arm with steel bushing use rear turning arm P N 02956830 or front turning arm P N 02956831 one or the other but not both 4 Replace two bushings in the cylinder clevis 3 with P N 02959890 bushing use suitable driver Align cyl clevis with turning arm bore and install new P N 02960458 Pin and cotter pin Lubricate pin and test for proper operation 2M oa Figure 1 TECHNICAL INFORMATION BULLETIN No 121295 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 17 TTT REM TECHNICAL INFORMATION BULLETIN No 121495 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Rear Mount Booms Machete Boom Axe Versa Boom A Boom and Bulletin No
53. ted date Ta All Service Bulletins printed in this Manual will void any previously printed Bulletin Any changes in these bulletins are the final version as of the date of this manual 2004 Alamo Group Inc INDEX MISCELLANEOUS MODELS Models With Few Bulletins Section 1 Technical Information Bulletins Bulletin No Old No Page Date Description nn 1 1 Information Bulletins Introduction 081594 940012 A 08 15 94 Motor High Pressure Seal Kit GK HY88 amp VP 011095 950001 i RA 01 10 95 King Post Attachment Components MM 8 RB E AA ES m 01 20 95 Flail Axe Head Pulley Fastening FA 061995 61995 4 e A 06 19 95 Boom Balance Recommendations BA 0 fo O r lA ias 09 28 95 Push Pull Power Switch Failure All 100595 srini 1 14 10 05 95 Main Frame Reinforcement Kit GK 2129 rioan ic s AA 12 12 95 Turning Arm Bushing Convert to Steel RB 121495 A 1 18 A 12 14 95 Rotary Boom Head Crack Repair RB amp BA 011290 AO RN RA 0 A 01 12 96 Speed Increaser Sealing Washer All OT TS A y A 01 15 96 Knife amp Retaining Rod Replacement FM 0408960 nisinsin AA 04 08 96 Oil Leaking from New Hydraulic Cylinders All A G pune usko y A 04 29 96 New Holland Tractor Dead Battery Problem All 10029051 soisissa AA 10 02 96 Logic Valve Seal Kit Update All 071897 0711897A Ji An 07 18 97 Remote Control Cab
54. to take up the space Flat Washer Part No 00023500 or equivalent can be used 6 Install the Knob using Locktite or similar thread locking compound Thread the knob on the rod all the way Test to make sure that when the switch is Off with rod pushed in that the knob can not travel further into the switch Continued Next Page MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 12 WITH NUT TIGHT AND SWITCH OFF MEASURE THIS GAP IF ANY Information Bulletin 092895 Continued from previous Page IF GAP EXIST INSTALL WASHERS OR SHIMS TO EQUAL GAP MEASURED IN MOUNTPLATE STEP 3 MOUNTPLATE KNOB SHOULD LIGHTLY CONTACT NUT WHEN PROPERLY ADJUSTED MOUNT PLATE TECHNICAL INFORMATION BULLETIN No 092895 Contact Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 Ph 830 372 2708 Fax 830 372 9603 This document does not authorize the repair or replacement of parts under warranty MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 13 TTT RAMS TECHNICAL INFORMATION BULLETIN No 100595 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models Grass King units produced prior to Oct 1995 Bulletin No Date 100595 Oct 5 1995 Main Frame Reinforcement Repair Kit Subject Akit is now available to repair or reinforce the main frame of the Grass King mowers The kit is designed to be installed on undamaged frames but can be u
55. ure 1 1 Tractor Boom Mower Stability Test Methods There are two acceptable methods for determining if the above requirements have been achieved A Drive on floor Scale Best Method Position the Boom as shown in Figure 1 Drive the tractor onto the scale so that only the left rear tire is on scale Note the weight If the weight is below 1 000 pound refer to the section on Improving Stability Ifthe weight is 1 000 pounds or more the unit has passed and is safe to operate as explained above N gt Continued Next Page MISCELLANEOUS MODELS 2004 Alamo Group Inc 1 8 Information Bulletin 061995 Continued from previous Page B Balance Weight Acceptable Method Position the Boom as shown in Figure 1 Place a 210 pound weight at the outer edge of the mower head as shown in figure 1 If the left rear tire lifts off the ground refer to the section on Improving Stability If the left rear tire remains firmly on the ground then the unit has passed and is safe to operate as explained earlier 2 Example Slope Mower Alamo Industrial has determined that the following tractor specifications will meetthe 1 000 pound requirement for a slope mower 2M Tractor Weight 5 500 Ibs Rear Tire SIZP second 18 4 30 Adjustable Wheels Adjusted to 8 ft 96 outside measurement Left rear proximately 50 from tractor center line and right rear proximately 46 from center line Tire Ballast Left re
56. valve section 2 Remove detent spacer item 6 as shown in figure 2 and reinstall detent assembly This will allow the detent valve to be positioned in float Tractor Start up 1 Be sure tractor is securely blocked transmission is in neutral park The forward reverse lever is in neutral 2 Remove the pipe plug from the reservoir and install the cap Check the oil level Replace any lost oil with Mercon or Dextron II 3 Start the tractor and run at idle Activate the valve handles to pressur ize valve sections and hoses Stop the engine and check for any leaks Figure 2 4 Lower the cab Watch for any wires fuel lines or any other comp onents that might be crushed as cab is being lowered Make sure the brake shaft does not cause fuel line to be pinched 5 Install cab support bolts spacers and large flat washers tighten the bolts Tighten the Valve assembly support bolt until it is snug 6 Recheck and replace any lost oil with Mercon or Dextron II or as specified for tractor by the tractor manufacturer 7 Reinstall the right wheel assembly ant tighten the retaining bolts 180 to 200 ft Ibs of torque 8 Wash and clean any spilled oil off of tractor around valve or cab Do not operate a tractor the has oil spilled on it as it could be a fire hazard SERVICE BULLETIN No 930510 Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial Warranty Polic
57. y Claim allowance may vary in accordance with laws governing a specific region Any Warranty associated with this service bulletin must be within authorized dates MISCELLANEOUS MODELS 2004 Alamo Group Inc 2 6 INDUSTRIAL SERVICE BULLETIN No 942801 Alamo Industrial Technical Services Department 1502 East Walnut Seguin Texas 78155 830 372 2708 Models ra Versa Pro S N VP21 01003 01005 01006 01007 01008 amp 01009 5 No Old 940005 Jan 28 1994 Labor Old Parts Disposition Termination Date 100 at Dealer Net 1 0 hr at Dealer registered Scrap removed parts Mar 30 1994 Shop Rate Mechanical Float Kit Subject Mechanical Float Components Kit will be shipped no charge to the dealers with the above listed serial number units All outbound freight will be shipped prepaid by Alamo This is to eliminate the requirement for the tractor to have remote valves with float Service Required Replace actuators with weldments item 8 and pins with components that were sent Pins and Hardware will have to be changed to complete this repair Item Part No Description 103266 Pin 02822500 Washer 00755153 Cotter Pin 107769 Actuator Wldmnt LH 107770 Actuator WIdmnt RH Note Most parts shown in this drawing are existing parts Figure 1 Warranty Compensation will be provided following proper filing of warranty claim in accordance with the Alamo Industrial Warranty Policy Claim allowance may vary

Miscellaneous Service Bulletin Manual

Contents

Download Pdf Manuals

Related Search

Related Contents