PIXUS 470PD i470D SERVICE MANUAL
Contents
1. LED power supply Logic power supply 3 3V JMUL1 Card connector Compact Flash Pin No WO 9 4 G Lh un GND CF_D3 CF_D4 CE DS CE Dp CF_D7 CF_CE1X CF_A10 CF_OEX CF_A9 CF_A8 CF_A7 VCC CF_A6 CF_AS CF_A4 CF_A3 CF_A2 CF_A1 CF_AO CF_DO CF_D1 CF_D2 CF_WP IOIS16X CF_CD2X CF_CDIX CF_D11 CF_D12 CF_D13 CF_D14 CF_D15 CF_CE2X CF_VS1X CF_IORDX CF_IOWRX CF_WEX CF_RDY BSYX VCC CSELX VS2X CF_RESET CF_WAITX CF_INPACKX CF_REGX CF_BVD2 CF_BVD1 CF_D8 CF_D9 CF_D10 GND CF GND 16 bit data bus 16 bit data bus 16 bit data bus 16 bit data bus 16 bit data bus Chip enable 24 bit address bus Memory read enable 24 bit address bus 24 bit address bus 24 bit address bus CF logic power supply 24 bit address bus 24 bit address bus 24 bit address bus 24 bit address bus 24 bit address bus 24 bit address bus 24 bit address bus 16 bit data bus 16 bit data bus 16 bit data bus Write protect Card detection Card detection 16 bit data bus 16 bit data bus 16 bit data bus 16 bit data bus 16 bit data bus Chip enable Voltage detection VO read enable VO write enable Memory write enable Data ready output CF logic GND Chip select signal Voltage detection Reset signal Wait signal Card response REG Data control output Data control output 16 bit data bus 16 bit data bus 16 bit data bus CF logic GND Function JMUL1 Card connector Smart Media Memory Stick SD MMC Signal Name V2. Perform the print head cleaning time Ink absorber After replacement Service test print QA4 0212 0213 Reset the waste ink counter Timing slit strip film Upon contact with the film After replacement Service test print QA4 0918 wipe the film with alcohol Perform the print head Confirm no grease is on the alignment in the user film Wipe off any grease mode thoroughly with ethanol Do not bend the film Purge unit Remove the carriage shaft QC1 2196 and then the purge unit Print head After replacement Service test print QY6 0047 Perform the print head alignment in the user mode General notes Make sure that the flexible cables and wires in the harness are in the proper position and connected correctly See page 1 7 1 for details Do not drop the ferrite core which may damage it Protect electrical parts from damage due to static electricity Do not touch the timing slit strip film No grease or abrasion is allowed Protect the units from ink contamination Do not loosen red screws 3 2 Special Notes on Repair Servicing 1 Cable wiring Exercise caution when handling the DC connector and motor cable wiring For wiring be sure to use ties cores and dampers Improper wiring or wiring without any ties cores and dampers may cause printer malfunction due to noise or electrostatic discharge lt Cable wiring gt Fix the DC harness PG motor cables PG sensor cables and CR
3. both selectable Timer cleaning 2 If 336 to 1 080 hours have elapsed since 0 36 black 50 black black color 0 28 color 55 color Timer cleaning 3 If 1 080 to 2 160 hours have elapsed 0 75 black since the previous black color cleaning 0 28 color both black and col we aceon till the start of the next printing Timer cleaning 4 If longer than 2 160 hours have elapsed 1 50 black both black and color since the previous black color cleaning 0 28 color ee sten till the start of the next printing Tf the print head has not been capped for 1 hour or the previous black color cleaning till 75 130 80 both black and longer before power on 0 24 black color both black and color 1 0 52 color 45 black At ink tank replacement 45 color O A L At print head replacement When the print head is removed and 0 36 black 110 both black and color installed 0 52 color AA E Via the operation panel both black 140 both black and Deep cleaning and color 1 50 black color black color both Via the printer driver black color or 0 52 color 85 black both selectable 70 color When 24 to 60 hours have elapsed since the previous black cleaning this cleaning is performed However the cleaning will be conducted up to 5 times from the printer installation After that when 60 to 180 hours have elapsed the cleaning will be performed 2 The period of time from the previous cleaning is cou
4. 300x600 MYC 600x600 4 passes MYC 1200x600 1 pass unidirectional Pigment Bk 600x600 3 passes Pigment Bk MYC Bk 600x600 MYC 1200x600 3 passes Pigment Bk MYC Bk 600x600 MYC 1200x600 1 pass Pigment Bk 600x600 1 pass 3 passes Pigment Bk MYC Pigment Bk MYC Pigment Bk MYC Bk 600x600 MYC 1200x600 4 passes Pigment Bk 600x600 4 passes Pigment Bk 600x600 4 passes Pigment Bk 600x600 4 passes Pigment Bk MYC Bk 600x600 MYC 1200x600 6 passes MYC 1200x600 4 passes Pigment Bk non 4 passes unidirectional Pigment Bk 600x600 12 passes MYC 1200x600 12 passes MYC 1200x600 1 j 12 passes MYC 1200x600 12 passes MYC 1200x600 6 passes Pigment Bk 600x600 12 passes MYC 1200x600 6 passes Pigment Bk 600x600 6 passes Pigment Bk MYC 1200x600 16 passes MYC 4800x1200 Yellow background Printing with 5 pl and 2 pl Blue background Printing with 2 pl 3 2 Resolution in Borderless Printing Media Type Quality Level5 Quality Level 4 Quality Level 3 Quality Level2 Quality Level 1 No of passes 3 passes Black composition MYC Resolution dpi 600x600 No of passes 12 passes 16 passes PR 101 PC 101 Black composition MYC MYC Resolution dpi 1 1200x600 4800x1200 No of passes 12 passes Black composition MYC Resolution dpi 1200x600 No of passes 4 passes 12 passes Black composition MYC N y MYC Resolution dpi 1200x600 1 1200x600 No
5. CK 8006 000 To improve the sliding property between the grounding spring QA4 1372 and the feed roller QF4 0212 1 5 Serial Number Location On the right side with the access cover opened on the carriage cable holder 2 LIST OF ERROR DISPLAY INDICATION Errors and warnings are indicated by the following methods 1 Errors are displayed by the number of times the LED blinks 2 Errors are displayed by the number displayed on the operation panel 3 Warnings are displayed via the printer driver status monitor 2 1 Errors by LED Blinking in Orange User recoverable errors LED blinking in Panel display Error Code Error Solution orange 2 times 301 1000 No paper Set the paper and press the Resume Cancel button 3 times 302 1300 Paper jam Remove the jammed paper and press the Resume Cancel button If the error is not resolved check that no foreign material is inside the printer 6 times 402 1401 The print head is not Install the print head and close the installed access cover 7 times 403 1405 The print head is not Re install the print head or with installed properly the print head installed turn the EEPROM data of the printer off and on If the error is not print head is faulty resolved replace the print head 8 times 202 1700 Warning The waste ink Pressing the Resume Cancel button absorber becomes almost will exit the error full to approx 95 to The waste ink absorber full error 100 of t
6. disabled there is no status display 2 AL the warning the carriage does not move to the ink tank replacement position when the access cover is opened 2 4 Troubleshooting by Symptom A Symptom Solution Pan Na The power does not turn on Replace the AC adapter The power turns off Replace the logic board ass y The print head is not Remove and re install the print head recognized Replace the print head Faulty The print head does not move to 3 Replace the logic board ass y Operation A strange noise occurs Check that no foreign material is inside the printer Attach a removed part if any Apply oil to the grounding spring Paper does not feed Remove foreign material if any Paper feed Replace the sheet feeder unit problems Paper feeds at an angle Remove foreign material if any Adjust the paper guide position Check whether ink remains or not Perform print head deep cleaning Replace the print head No printing or no color ejected a ac Printing is faint or white lines appear on printouts even after print head cleaning Line s not included in the print Remove and re install the print head Check whether ink remains or not Perform print head deep cleaning Replace the print head AS Paper gets smeared Feed several sheets of paper Clean the paper path with cotton swab or cloth Replace the platen unit Replace the ink tank Replace the print head Check whe
7. of passes 12 passes Black composition I MYC Resolution dpi 1200x600 No of passes 12 passes Black composition MYC Resolution dpi l 12 1200x600 3 passes 4 passes MYC MYC 600x600 1200x600 Plain Paper No of passes 1 pass 1 pass 1 pass 4 passes Monochrome Black composition Pigment Bk Pigment Bk Pigment Bk Pigment Bk Resolution dpi 300x600 300x600 600x600 600x600 No of passes Bk 1 pass 1 pass 1 pass No of passes Color 1 pass 1 pass 3 passes Black composition Pigment Bk MYC Pigment Bk MYC Pigment Bk MYC F Resolution dpi Bk 300x600 Bk 300x600 Bk 600x600 MYC 600x600 MYC 600x600 MYC 1200x600 3 4 Resolution in Direct Printing The printed resolution is the same for both Card Direct Printing and Camera Direct Printing Passes 9 passes Black composition M Y C Resolution dpi 1200 x 600 Dot size 5 pl and 2 pl 4 FAQ Specific Problems and Solutions level 1 Paper Paper not feeding When the plain paper flexible As the paper is flexible When plain paper is used be Paper jam feeding paper such as SK paper is cut and the paper size is sure to use B5 size or larger Paper not feeding into 100mmx148mm size and small it winds around is fed the paper feed roller Writing to SD card not written With the SD card is inserted Depending on the Insert the card with care not to Writing to the SD card is memory to into the card slot method of inserting the Lock the wr
8. CC 22 GND 1 SM_CEX 21 SM_CLE 2 SM_REX 20 SM_ALE 3 SM_WEX 4 GND 18 M_WPX 5 M_LVD 17 M_D7 16 S S S S S S M_D6 15 SM_D2 8 SM_D5 14 SM_D3 9 SM_D4 13 GND 10 VCC 10 SM_CDX 11 SM_CDSW SM_CDSW SM_WPSW SM_WPSW GND VCC MS_SCLK Reserve MS_INS Reserve MS_DIO VCC MS_BS GND SD_DAT2 SD_CD DAT3 SD_CMD GND VCC SD_CLK GND SD_DATO SD_DATI SD_CDSW SD_WP CDSW SD_WPSW SM_RDY BSYX 19 Function SM logic power supply SM GND Chip enable Command latch enable Output enable Address latch enable READY BUSY Write enable SM logic GND Write protect Low voltage detection 16 bit data bus 16 bit data bus 16 bit data bus 16 bit data bus 16 bit data bus 16 bit data bus 16 bit data bus 16 bit data bus Logic GND SM logic power supply Card detection Card detection SW Card detection SW Write protect SW Write protect SW MS logic GND MS logic power supply Serial clock For chip test unusable Card detection For chip test unusable 16 bit data bus MS logic power supply Bus state MS logic GND 16 bit data bus 16 bit data bus 16 bit data bus SD logic GND SD logic power supply Clock data SD logic GND 16 bit data bus 16 bit data bus Card detection SW Write protect card detection SW Write protect SW 2 2 Carriage Board J50 Carriage ribbon cable connector Refer to JCRB1 Carriage ribbon cable connector on page 3 2 J51 Carriage ribbon cable connector Refer to JCRB2
9. Carriage ribbon cable connector on page 3 2 J52 Print head contact Pin No Signal Name Function 1 to 39 Referto2 3 Printhead on page 3 8 2 3 Print Head 25 26 40 B_DATA_Y2 VSS A_GNDH B_DATA_M1 B_DATA_M2 B_DATA_Y1 CLK LT B_HE2 B_DIK VHT B_HEI VDD E_DI B_RANK NC B_DATA_CI B_DATA_C2 B_VH E_SK E_CS B_DIA E_DO B_SH NC A_VH A_DATA_KI A_SH NC A_RANK NC A_DIK A_DIA A_DATA_K2 A HE Function Heater GND Serial data input for Y2 heater Logic GND Heater GND Serial data input for M1 heater Serial data input for M2 heater Serial data input for Y1 heater Clock signal Data latch enable signal Heat enable signal Head temperature sensor cathode side Head power transistor drive power supply Heat enable signal Logic power supply Head EEPROM serial data input signal Unused Serial data input for C1 heater Serial data input for C2 heater Heater power supply Head EEPROM serial data clock input signal Head EEPROM chip select input signal Head temperature sensor anode side Head EEPROM serial data output signal Unused Heater power supply Serial data input for BK1 heater Unused Unused Head temperature sensor cathode side Head temperature sensor anode side Serial data input for BK2 heater Heat enable signal 2 4 lt Printer gt Type Paper feeding method Resolution Throughput Target value Printing direction Print width Interface ASF stacking capacity Paper weight Detect
10. F BkBi 000 G C1Bi 000 H BkCI 000 I LCBi 000 J C_LC 000 K M_LM 000 ST 2002 9 15 20 15 PW ON 0009 OFF 00005 BORDERLESS 00000 PAGE ALL 00562 PP 00025 PC 0000 PR 00050 MP 0000 SP 0258 CAMERA BORDERLESS 0030 NORMAL 0028 Card CF 0035 MS 0000 SM 0005 SD 0004 PC 1 CP PR 00017 00068 SP 00025 00039 MP 00465 00643 PP 00025 HDEEPROM V0000 SN 0318 A43D EN 04 05 01 06 00 00 03 DI Bk 001 CL 001 IL Bk 08 C 08 M 08 Y 08 WLA 08 WLB 08 NGBk 000 NGC 000 NGM 000 NGY 000 The information surrounded by a blue border is printed in the service test print also Model name ROM version destination waste ink amount number of pages printed number of times the head was installed bi directional registration black color Head temperature black color internal temperature process inspection information USB serial number Number of times cleaning was performed manual deep cleaning timer dot count head ink tank replacement dot count of each color Operator service call history occurrence time ERO 1 2 3 Total ink consumption Bk 00000000mg C 00000000mg M 00000000mg Y 00000000mg Cleaning time number of times cleaning was performed manual deep cleaning timer dot count head ink tank replacement dot count of each color Ink sponge recognition flag number of times wiping was performed User s print head alignment values User s print head alignment values Installation date number of times printer was
11. PIXUS 470PD 1470D SERVICE MANUAL Revision O YRIGHT 2003 CANON INC CANONPIXUS 470PD 1470D 032003 CA 0 00 0 Scope This manual has been issued by Canon Inc to provide the service technicians of this product with the information necessary for qualified persons to learn technical theory maintenance and repair of products The manual covers information applicable in all regions where the product is sold For this reason it may contain information that is not applicable to your region Revision This manual could include technical inaccuracies or typographical errors due to improvements or changes made to the product When changes are made to the contents of the manual Canon will release technical information when necessary When substantial changes are made to the contents of the manual Canon will issue a revised edition The following do not apply if they do not conform to the laws and regulations of the region where the manual or product is used Trademarks Product and brand names appearing in this manual are registered trademarks or trademarks of the respective holders Copyright All rights reserved No parts of this manual may be reproduced in any form or by any means or translated into another language without the written permis sion of Canon Inc except in the case of internal business use Copyright 2003 by Canon Inc CANON INC Printer Products Quality Assurance Div 16 1 Shimonoge 3 chome Takatsu ku Kawasaki Kanag
12. RENCE 1 2 CLEANING MODE AND AMOUNT OF INK PURGED 3 NEW TECHNOLOGIES RESOLUTION BY PRINT MODE 3 1 Resolution by Print Mode during Printing via Computer 3 2 Resolution in Borderless Printing 3 3 Resolution in Duplex Printing 3 4 Resolution in Direct Printing 4 FAQ Specific Problems and Solutions Part 3 APPENDIX 1 2 CONNECTOR LOCATION AND PIN LAYOUT BLOCK DIAGRAM 2 1 Logic Board Ass y 2 2 Carriage Board 2 3 Print Head 2 4 1470D PIXUS 470PD Specifications Part 1 MAINTENANCE 1 MAINTENANCE 1 1 Adjustment Periodic Maintenance Periodic Replacement Parts and Replacement Consumables by Service Engineer 1 Adjustment time EEPROM At logic board ass y To initialize settings other None 1 min initialization replacement than the following USB serial number Destination setting On arrival cleaning flag Waste ink counter Destination settings At logic board ass y To set the destination None 1 min PAN fe e Waste ink counter At ink absorber To reset the waste ink None 1 min Print head alignment At print head or logic To ensure accurate dot Computer 2 min board ass Y replacement placement settings via the printer driver 2 Periodic maintenance No periodic maintenance is necessary 3 Periodic replacement parts There are no parts in this printer that require periodic replacement by a service engineer 4 Replacement consumables There are no consumables that requir
13. awa 213 8512 Japan I MANUAL OUTLINE This manual consists of the following three parts to provide information necessary to service the 1470D Part 1 Maintenance Information on maintenance and repair of the 1470D Part 2 Technical Reference New technology and technical information such as FAQ s Frequently Asked Questions of the i470D Part 3 Appendix Block diagrams and pin layouts of the i470D Reference This manual does not provide sufficient information of disassembly and reassembly procedures Refer to the graphics in the separate Parts Catalog Il Page 1 1 1 1 Rh e ko 1 1 1 1 1 1 E LM LM HA HA LA LA Rosana AD Mar 1 2 1 29 2 3 2 3 2 4 2 4 2 4 2 5 3 1 3 2 3 2 3 8 3 9 TABLE OF CONTENTS Part 1 MAINTENANCE 1 MAINTENANCE 1 1 Adjustment Periodic Maintenance Periodic Replacement Parts and Replacement Consumables by Service Engineer 1 2 Customer Maintenance 1 3 Product Life 1 4 Special Tools 1 5 Serial Number Location 2 LIST OF ERROR DISPLAY INDICATION 2 1 Operator Call Errors by LED Blinking in Orange 2 2 Service Call Errors by LED Blinking in Orange and Green Alternately or Lit in Orange 2 3 Warnings 2 4 Troubleshooting by Symptom REPAIR 3 1 Notes on Service Part Replacement and Disassembling Reassembling 3 2 Special Notes on Repair Servicing 3 3 Adjustment Settings 3 4 Verification Items 4 PRINTER TRANSPORTATION METHOD Part 2 TECHNICAL REFE
14. e replacement by a service engineer 1 2 Customer Maintenance time Print head alignment At print head To ensure accurate dot Printer or 5 min replacement placement computer settings via the printer driver Print head cleaning When print quality is To improve nozzle Printer or 30 sec to not satisfying conditions computer 1 min settings via the printer driver Print head deep cleaning When print quality is To improve nozzle Printer or 1 5 to 2 5 not satisfying and not conditions computer min improved by print head settings via the cleaning printer driver becomes empty cleaning feed properly feed rollers 1 3 Product Life 1 Printer The value 1 or 11 whichever comes first i 4 000 pages of printing Black 1 200 pages A4 1 500 character pattern Color 2 800 pages A4 7 5 duty per color pattern 1 300 pages A4 30 duty per color pattern 500 pages 100 x 148 mm 30 duty per color pattern 700 pages 89 x 127 mm size 30 duty per color pattern 300 pages ii 5 years of use 2 Print head 4 000 pages of printing in the above print mode 3 Ink tank BCI 24Black 300 pages 1 500 character pattern in black printing plain paper standard mode 580 pages ISO JIS SCID No 5 pattern plain paper standard mode BCI 24Color 160 pages ISO JIS SCID No 5 pattern plain paper standard mode 1 4 Special Tools Name Remarks carriage shaft QC1 2196 LF gear ELECTRICITY IF 20
15. ectromagnetic radiance VCCI FCC IC C tick Taiwan EMC Korea EMC CCIB CCEE Electrical safety Electrical Appliance and Material Control Law DENTORD UL C UL CB Report GS CE Mark FIMKO CCIB EMC AS CCEE PSB Electrical Safety Regulations of Korea SASO Environmental regulations Energy Star Blue Angel Environment label On the carriage ribbon cable holder visible when the access cover is open Available by dot count reset by user operation enabled at default Available 11 types CANON INC 3 9
16. eplace the ink absorber 2 Replace the logic board ass y 8 times 808 5200 Print head temperature rise 1 Turn the printer off and after a error short period of time turn the printer on again 2 Replace the print head 3 Replace the logic board ass y 6800 EEPROM error Replace the logic board ass y No display 6800 Replace the logic board ass y orange 1 The error code is stored in the operator service call history of the EEPROM information 2 3 Warnings Printer no LED indications Low blackink warning 1 About half of the full amount remains The status is displayed on the BJ printer Low color ink warning 1 About half of the full amount remains driver status monitor Low black ink warning 2 Little ink remains Low color ink warning 2 Little ink remains Low black ink warning 3 An unknown amount remains al Low color ink warning 3 An unknown amount remains Print head temperature rise warning If the print head temperature is high when the access cover is opened the warning is displayed When the print head temperature falls the warning is released Protection at excess rise of the print head temperature If the print head temperature exceeds the specified limit a Wait is inserted during printing When the print head temperature falls printing will resume automatically Only when the remaining ink amount detection function is enabled When
17. ervice test print When the Power button is pressed during printing printing L TE stops and the mode returns to step 4 above 2 times When the Power button is pressed during printing printing stops and the mode returns to step 4 above Sims Times 5 times Orange Destination settings Proceed to the following steps 5 and then 6 to set the destination 6 times Print head deep cleaning Cleans black and color simultaneously Times 8 times Green Return to the menu selection Return to step 4 above or more 5 After the function menu is selected press the Power button The LED lights in green and the selected function is performed When the operation completes the printer returns to step 4 above lt Destination setting gt 6 Press the Resume Cancel button the specified number of time s according to the destination listed in the table below and then the Power button Time s LED Destination 1 time Orange Overseas i470D 2 times Japan PIXUS 470PD 1 10 lt Operation panel operation verification procedures gt After performing the above service mode operation procedures up to step 3 with 02 indication in the operation panel press the specified operation button Icons are displayed on the LCD as shown below to verify the operation buttons and panel displays 1 When pressing the left Cursor button 2 When pressing the right Cursor button pT eee be 3 When pres
18. he maximum occurs at 100 capacity making it capacity impossible to perform printing 11 times 611 2001 Digital camera Disconnect the USB cable to the transmission time out digital camera and press the error When the printer Resume Cancel button cannot communicate with a digital camera the time out error occurs 612 2001 Digital camera Disconnect the USB cable and non supporting device press the Resume Cancel button error When a digital camera or device other than a digital camera not supporting Direct Printing is connected to the printer with the USB cable the error occurs 1 The error code is stored in the operator service call history of the EEPROM information 2 2 Errors by LED Blinking in Orange and Green Alternately or Lit in Orange User unrecoverable errors LED alternate blinking in Panel display Error Code Error Solution orange and green 2 times 802 5100 Carriage error 1 Check that no foreign material is inside the printer 2 Replace the timing slit strip film 3 Replace the purge unit 4 Replace the logic board ass y 4 times 804 5C00 Purge unit error 1 Check that no foreign material is inside the printer 2 Replace the purge unit 3 Replace the logic board ass y 6 times 806 5400 Internal temperature error 1 Turn the printer off and after a short period of time turn the printer on again 2 Replace the logic board ass y 7 times 807 5B00 Waste ink absorber full error 1 R
19. ial data H_LATCH Head data latch DIA1 Temperature detection diode anode unused DIKO Temperature detection diode cathode HDATA7 Y2 Y2 serial data H_CLK Head clock E CS Head EEPROM chip select HDATAC Y 1 Y 1 serial data E_SK Head EEPROM serial clock H_ENB1 Heat enable HDATAS M2 M2 serial data HDATAO BK1 BKI serial data HDATA4 M1 M serial data JUBA1 USB A interface connector DSC Pin No Function 5V Cable power supply Differential data signal Differential data signal GND E Un Pin No Function 1 Cable power supply 2 Differential data signal 3 Differential data signal 4 GND JPOW1 DC power supply connector Pin No Function 1 5V power supply 2 3 4 GND 5 5V logic power supply 6 24V motor power supply 7 24V head power supply JLFM1 LF motor connector Pin No Function LF motor phase A LF motor phase B LF motor phase A LF motor phase B hh Un JAPM1 ASF PG motor connector Pin No Signal Name Function 1 ASF PG motor phase A 2 ASF PG motor phase B 3 ASF PG motor phase A 4 ASF PG motor phase B JCRM1 Carriage motor connector Pin No Signal Name Function 1 CRB Carriage motor phase B CRA Carriage motor phase A JOP1 OP panel connector Signal Name Pin No WO 9 4 G Lh un GND RESETX RESUME POWER LED_RSM LED_POW 03 3v Function Serial sending data output Serial sending data input GND Reset input signal Resume input signal Power supply output LED resume output
20. ing the Photo Viewer button in the operation panel will start the Photo Viewer on the computer This application is used only to see the images on the memory card and printing operations are performed via the operation panel 2 CLEANING MODE AND AMOUNT OF INK PURGED To prevent printing problems due to bubbles dust or ink clogging print head cleaning is performed before the start of printing except in the following cases Cleaning on arrival Performed when the access cover is closed Cleaning by dot count Performed after ejection of paper Manual cleaning deep cleaning Performed manually lt Cleaning mode list gt Condition Details Amount ofink Est required time used g sec On arrival of the printer First cleaning after shipped from the 0 36 black both black and COMO A ne N 0 52 eolo When the specified number of dots are Dot count cleaning printed from the previous black color black color cleaning Dots are counted by black and color separately If 24 to 180 hours have elapsed since x 1 Timer Cleaning 0 the previous black cleaning till the start black only of the next printing ee If 180 to 336 hours have elapsed since 9 14 e 38 colon Timer cleaning 1 the previous black color cleaning till black color the start of the next printing Time is DE Via the operation panel both black Manual cleaning and color black color both Via the printer driver black color or
21. ion functions Acoustic noise Environmental requirements Power supply External dimensions Weight Related standards Printer Adapter Serial number location Remaining ink amount detection Print head alignment PRINTED IN JAPAN IMPRIME AU JAPON i470D PIXUS 470PD Specifications Desktop serial color bubble jet printer Auto sheet feed no manual feeding 4 800 dpi x 1 200 dpi Max rss DER E Standard High Black New Black 18 ppm ppm Color New Color 12 ppm 4 9ppm 0 8ppm Bidirectional uni directional Max 203 2 mm 220 4 mm in borderless printing USB 2 0 Full Speed Plain paper 75 g nt Max 10 mm Approx 100 sheets 64 to 105 g n Cover open Presence of print head Distinction of print head Remaining ink amount dot count Printing position Paper out Paper end sensor Waste ink amount Internal temperature Pick up roller Paper feed roller position Carriage position 46 dB Head to paper distance During operation Temperature 5C to 35C 41F to 95F Humidity 10 RH to 90 RH no condensation Non operation Temperature OC to 40C 32F to 104F Humidit 5 RH to 95 RH no condensation Input voltage Frequency Power consumption Standby _ Power off AC 100 to 127 V 50 60 Hz 32 W 2 5 W 1 3 W AC 220 to 240 V 50 60 Hz 30 W 2 6 W 1 3 W Approx 393 W x 258 D x 218 H mm Approx 4 kg not including print head and optional device El
22. ite protection not possible card SD card write switch protection is Locked in rare cases N S level The symptom is likely to occur frequently gt The symptom may occur under certain conditions but likeliness is assumed very low in practical usage C The symptom is unlikely to be recognized by the user and no practical issues are assumed Part 3 APPENDIX 1 BLOCK DIAGRAM LOGIC BOARD ASS Y QM2 0483 PRINT HEAD OPERATION PANEL UNIT 256pin_BGA ASF PG MOTOR 5in1 CR Connector Compact Flash Memory Stick MOTOR y il Multi Media Card SD Card Smart Media AC Digital Camera Adapter Digital Video Camera 2 CONNECTOR LOCATION AND PIN LAYOUT 2 1 Logic Board Ass y N RUTT MEC 7 LNG Figure 3 1 Logic Board JCRB1 Carriage ribbon cable connector Pin No Function 1 2 3 4 HVH Head drive 24V power supply 5 6 7 8 Head drive GND 9 10 11 12 HVH Head drive 24V power supply 13 14 15 16 H_GND Head drive GND 17 18 HVH Head drive 24V power supply 19 20 H_GND Head drive GND 21 ENC_OUTO Encoder output 22 ENC_OUTI Encoder output 23 ENC_PWR Encoder power supply 24 25 HVDD Head logic 3 3V power supply 26 HDATA2 C1 Cl serial data 27 HDATA3 C2 C1 serial data Function S_GND Signal GND DIK1 Temperature detection diode cathode unused DIAO Temperature detection diode anode H_ENBO Heat enable HDATA1 BK2 Black serial data H_DIO Head EEPROM serial data E_DIO Head EEPROM ser
23. motor cables with a tie Fix the PG sensor cables and CR motor cables in the claw Fix the DC cables and PG motor cables in the damper Fix the LF motor cables with the core 2 Handling of logic board As the 4 in 1 connector pin functions on the logic board ass y can be easily bent exercise care to avoid bending the pins when removing or installing the connector on the logic board If pins are bent a card non recognition failure or a Direct Printing failure may occur 3 Removing the purge unit When removing the purge unit the carriage shaft must be removed in advance The purge unit cannot be removed without first removing the carriage shaft If the purge unit is removed forcibly it may be damaged or the carriage shaft may be damaged causing uneven print density in printouts 3 3 Adjustment Settings 1 User mode The printer is operated through the Resume Cancel button or operation panel lt Operation via the Resume Cancel button gt 1 Turn on the printer 2 Press and hold the Resume Cancel button until the LED blinks in green the specified number of times listed in the table below and release the button The operation will start LED blinking Operation Remarks 1 time 2 times 3 times 4 times or more Cleaning both black and color simultaneously Nozzle check pattern printing The operation can also be performed from the printer Paper feed roller cleaning driver utility lt O
24. nted by black and color separately For this reason the cleaning mode may differ for black or color 3 RESOLUTION BY PRINT MODE 3 1 Resolution by Print Mode during Printing via Computer Media Type Quality Level 5 Quality Level 4 Quality Level 3 Quality Level 2 Quality Level 1 Plain Paper Monochrome High Resolution Paper HR 101 Monochrome High Resolution Paper Photo Paper Pro PR 101 PC 101 PH 101 Glossy Paper GP 301 KH 201 Photo Paper Plus Matte Photo Paper MP 101 Postcard for ink jet printers Monochrome Postcard for ink jet T Shirt Transfers TR 101 Transparencies CF 102 No of passes Black composition Resolution dpi No of passes Bk No of passes Color Black composition Resolution dpi No of passes Black composition Resolution dpi No of passes Black composition Resolution dpi No of passes Black composition Resolution dpi No of passes Black composition No of passes No of passes Black composition Resolution dpi No of passes Black composition Resolution dpi No of passes Black composition Resolution dpi No of passes Black composition Resolution dpi No of passes Black composition Resolution dpi No of passes Black composition Resolution dpi No of passes Black composition Resolution dpi 1 pass Pigment Bk 300x600 1 pass 1 pass Bk 300x600 MYC 600x600 1 pass Pigment Bk 300x600 1 pass 1 pass Bk
25. peration via the operation panel gt 1 Press the Maintenance button 2 Using the Left Right cursor buttons change the number displayed in the operation panel for the desired function listed in the table below and press the Set button to execute the function Panel Display E EAN Remarks 01 Cleans black and color simultaneously Cleans black and color simultaneously Using the printout set the optimum values Set the ink remaining counter to 100 Ink remaining display setting Ink remaining icon is displayed or not displayed on the operation panel Date order setting in date print The following three date orders are possible 1 Year month date 2 Month date year 3 Date month year 2 Service mode Function Procedures Remarks Service test print See Service mode operation Seta sheet of A4 LTR or larger sized paper procedures below For print sample see page 1 12 EEPROM information print See Service mode operation Seta sheet of A4 LTR or larger sized paper procedures below For print sample see page 1 13 EEPROM initialization See Service mode operation The following items are not initialized procedures below USB serial number Destination settings Japan Overseas Cleaning flag on arrival Waste ink counter Waste ink counter reset See Service mode operation Both the main and the borderless print waste procedures below ink counters are reset at the same
26. sing the Set button 6 When pressing the Print button L PP eee 7 When pressing the Cancel button 1 11 3 4 Verification Items 1 Service test print After repair print the service test print and confirm the following items lt Print quality items gt Check 1 top of form accuracy The line shall be within the paper Check 2 EEPROM information Destination and waste ink counter shall be checked Check 3 nozzle check pattern Ink shall be ejected from all nozzles Check 4 vertical straight lines The lines shall not be broken Check 5 halftone There shall be no remarkable streaks or unevenness Check 1 Check 2 EEPROM information Refer to page 1 13 Check Nozzle check pattern Check 4 Vertical straight lines Check 5 Halftone 1 12 2 EEPROM information contents On the EEPROM information print the printer usage conditions can be confirmed Refer to the sample print given below aus t NO OO J C 13 14 i 10 HeadT Bk 25 5 HeadT C 25 0 EnvT 30 0 FA 01 87 80 USB 1000AQ x 1 3 PIXUS 470PDP V 1 00 Destination 02 D 004 8 Page 00562 CH 0002 Bk 00 4 2 ME 001013 21 48 EROS 51001 ERI 200 ER2 1000 ER3 TD TotalINK Bk 00057098 C 00008108 M 00006992 Y 00007666 CLTime 2002 10 15 15 36 PC M 0028 R 0015 T 0000 D 0020 C 0009 IC Bk 1 C 1 M 1 Y 1 WP 0025 SetUsrReg NONE URI A Bkeo 000 B Ce0 000 C Meo 000 Yeo 000 D Lceo 000 E Lmeo 000 Lyeo 000 UR2
27. ther ink remains or not Perform print head deep cleaning Replace the print head Mee w Unsatisfactory print quality A part of a line is missing on printouts Color hue is incorrect N Re aD Check whether ink remains or not Perform Refreshing No ejection of black ink ne jan Graphic or text is extended on Clean the timing slit strip film with printouts alcohol Replace the timing slit strip film Replace the logic board ass y Replace the carriage unit Confirm the card installation status Release the maintenance mode Format the card on the digital camera Replace the logic board ass y Check that images exist in the card Direct Check the data volume in the card and Printing related format type problems 3 Replace the logic board ass y Card is not recognized Ren lKa H Image data is not recognized Ne Digital Camera Direct Printing 1 Check that the printer supports Digital cannot be performed Camera Direct Printing 2 Check that no errors occur in the printer 3 Replace the logic board ass y 3 REPAIR 3 1 Notes on Service Part Replacement and Disassembling Reassembling Notes on replacement Adjustment settings Operation check Logic board ass y Do not bend the 4 in 1 After replacement Service test print QM2 0483 connector pin Initialize the EEPROM Set the destination in the EEPROM Perform the print head alignment in the user mode
28. time Destination settings See Service mode operation Overseas 1470D procedures below Japan PIXUS 470PD Print head deep cleaning o Cleans black and color simultaneously Operation panel display See Operation panel operation Confirm the operations of operation panel confirmation confirmation procedures display and operation buttons Perform the below confirmation at operation panel replacement lt Service mode operation procedures gt 1 Close the access cover and turn off the printer While pressing the Resume Cancel button press and hold the Power button The LED lights in green to indicate that a function is selectable 2 While holding the Power button release the Resume Cancel button 3 While holding the Power button press the Resume Canc el button 2 times and then release the Power and Resume Cancel buttons In the operation panel 02 will be displayed Each time the Resume Cancel button is pressed the LED lights alternately in either orange or green During initialization the LED blinks in green 4 When the LED stops blinking and lights in green press the Resume Cancel button the specified number of time s according to the function listed in the table below Each time the Resume Cancel button is pressed the LED lights alternately in either orange or green Time s Remarks U times When the print head is not installed the carriage returns and locks in the home position l time Orange S
29. tress to the carriage flexible cable or causing ink leakage during transportation Note Tf the print head must be removed from the printer and transported alone perform the following 1 Install both the black and color ink tanks to prevent the nozzles from drying 2 Attach the protective cap to protect new packaged print heads to the print head to protect the print head face from damage due to shocks 1 14 Part 2 TECHNICAL REFERENCE 1 NEW TECHNOLOGIES 1 1 4in 1 Slot For memory card direct printing a 4 in 1 card slot is adopted and the memory card direct printing can be performed without the PCMCIA card adapter Supported media are as follows Compact Flash MicroDrive Memory Stick SD Card Multi Media Card SmartMedia XD Card Sliding the card slot up and down prevents two cards from being inserted simultaneously For the XD Card a Compact Flash type adapter is necessary 1 2 2 pl Print Mode For the print head staggered color nozzle arrays of 5 pl and 2 pl are adopted enabling high quality printing For the 2 pl print mode refer to 3 RESOLUTION BY PRINT MODE on page 2 3 Black 160 nozzles x 2 lines Color 128 nozzles x 2 lines x 3 colors M Y C 160 nozzles 128 nozzles 1 3 Photo Viewer It is not possible to install the Image Viewer To see images on the memory card it is necessary to use Photo Viewer Photo Viewer is automatically installed at printer driver installation and press
30. turned on off number of borderless printing pages Number of pages fed all plain paper postcard Photo Paper Pro Matte Photo Paper Photo Paper Plus Glossy Number of pages in Digital Camera Direct Printing borderless bordered Number of times memory card was inserted CF MS SM SD Connection to PC O not connected 1 connected Number of pages in Memory Card Direct Printing Photo Paper Pro borderless bordered Photo Paper Plus Glossy borderless bordered Matte Photo Paper borderless bordered plain paper HEAD EEPROM Version Serial number Lot number DI sensor adjustment value Ink ejection level Overlay level Number of unusable nozzles Bk C M Y The time the user last performed printing before the error occurred 1 13 PRINTER TRANSPORTATION METHOD This section describes the procedures for transporting the printer for returning after repair etc 1 Keep the print head and ink tanks installed in the carriage 2 Turn off the printer and secure the carriage locked in home position When the printer is turned off the lock pin automatically locks the carriage in place Caution If the print head is removed from the printer and left unprotected ink in particular the pigment black ink is likely to dry For this reason keep the print head installed in the printer even during transportation Also securely lock the carriage in the home position to prevent the carriage from moving and applying s
Download Pdf Manuals
Related Search