pin type fork positioner with shifting sf-f model
Contents
1. rollers after cleaning Check the oil level in the forklift s tank Repair or replace the truck s pump Increase the pressure Flush the truck system and check the oil level Flush the plant NOTE If you have trouble making the repair or the problem is not listed do not hesitate to contact BOLZONI s technical service department Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING SF F MODEL 6 MATERIAL DISPOSAL SSOILZIOIN fe 2 ANTAMNMO III 72 6 1 If replaced pieces are scrapped their disposal must be differentiated depending on the nature of the material and in conformity with the law governing the disposal of solid industrial waste Frame assembly Screws pipes and other components Welded frame Steel Pipes and fittings Nylon and steel Supports Steel Hydraulic oil oo of in conformity with local Fastening cylinders Steel Bushings Steel and teflon Chrome bar Steel and chrome Plugs screws bolts seegerrings Steel Paint Polyester epoxy O ring rubber Cylinder Steel and chrome Gaskets Polyurethane Shifting cylinder stems Steel and chrome Slide blocks Polyamide Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL JIAITAINMO Wrz 7 WARRANTY All the products by BOLZONI S p A are provided with a 12 month warranty when used for 8 hours per working day beginning from the date of shipment If used for more than 8 hours per day the warranty peri2. tracks Deformed frame Mud or other obstruction on the track of the lower rollers Flexible hoses deteriorated Obstructions in the hydraulic circuit Insufficient pressure Pump deteriorated SSOILZIOIN f 2 ANTAMNMO IN ff REMEDIES Remove obstacles clean and grease the sliding tracks Check and adjust the truck s pump pressure Remove the obstruction or replace the damaged hose Check and replace the gaskets see steps 4 3 2 and or 4 3 3 and 4 3 5 Check and adjust the flow rate supplied from the hydraulic circuit Adjust the truck oil flow Remove the obstruction or replace the damaged hose Check and replace the gaskets see steps 4 3 2 and or 4 3 3 and 4 3 5 Check and adjust the flow rate supplied from the hydraulic circuit Adjust the truck oil flow Remove obstacles clean and grease the sliding tracks Replace the frame removing it following step 4 3 5 Clean and lubricate the slide blocks as in step 4 2 1 Replace the hoses Remove the obstruction Increase the pressure Repair or replace the truck s pump Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING SF F MODEL FAULTS CAUSES 5 6 Side shifting occurs too slowly Slide rollers worn Emulsified oil the pump sucks air Pump deteriorated Insufficient pressure Air in the hydraulic system 5 7 Side shifting is jerky or irregular Air in the system IN ff SSOILZIOIN fe 2 ANTAMNMO REMEDIES Replace the
3. CIAL MAINTENANCE Fig 009 4 3 1 Preliminary Operations Before performing any maintenance turn off the truck and release the pressure in the supply circuit Ensure that during maintenance the pump and the distributor lever are not engaged 4 3 2 Removing the right shifting fork cylinder Fig 009 Remove the connecting pipes of the hydraulic circuit from the right cylinder as seen by the truck operator following all precautions referred to in step 4 3 1 Holding the opposite hexagon with a fixed wrench ch60 U02 loosen the nut with the socket wrench U02 ch50 Unscrew the nut on the back with the socket wrench ch50 U01 Remove the cylinder To reassemble the cylinder perform above tasks in reverse order Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL ALIrITAIViO Ws 4 3 3 Removing the left shifting fork cylinder Fig 010 Fig 010 Remove the connecting pipes of the hydraulic circuit from the left cylinder following all precautions referred to in step 4 3 1 Holding the opposite hexagon with a fixed wrench ch60 U02 loosen the nut with the socket wrench U02 ch50 Unscrew the nut on the back with the socket wrench ch50 U01 Remove the cylinder To reassemble the cylinder perform above tasks in reverse order Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL JIAITANMO Wrz 4 3 4 Removing and installing the low
4. IONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL ALIr TAIViO Ws 4 2 Routine maintenance Fig 008 4 2 1 Every 1000 Working Hours Check of the tightening torque of the screws in points C2 17 mm Allen key Torque 540 Nm Check of the tightening torque of the screws in points C3 12 mm Allen key Torque 195Nm Check of the tightness of the hydraulic fittings Greasing of points gl and g2 General inspection of the equipment Specific inspection of pipes condition Check of the integrity of fork support rollers Check of the hydraulic connections tighten the fittings to the cylinders as necessary according to the regulations of the fittings used Check of the tightness of the cylinder seals as necessary or in presence of leaks disassembly the cylinders according to the instructions in steps 4 3 1 4 3 5 ee mi 22 Frog in ES Fig 008 Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING E LELO JN I gv SF F MODEL AUIRAMO 4 2 2 Every 2000 Working Hours In addition to what is described in the previous step please perform Check of the cylinder stems and the guide bushings scratched or dented stem and scored or worn bushings as well as excessive play to the stem gt 0 25 mm or 0 001 inc requires the parts replacement Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL ALIrITAIViO Ws 4 3 SPE
5. PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL JIAITANMO Ws 1 DESCRIPTION AND FUNCTIONING 1 1 Positioner 2 ASSEMBLY INSTRUCTIONS 2 1 Positioner 2 2 Hydraulic System 2 3 Mounting and dismounting forks 2 4 Protection Grid Assembling 2 5 Test operation 3 USE INSTRUCTIONS 3 1 Checks and Recommendations 3 2 Manoeuvres to be Avoided 3 3 Prohibited Manoeuvres 4 MAINTENANCE 4 1 Introduction 4 2 Routine Maintenance 4 3 Special Maintenance 4 4 Hydraulic System Diagram 5 TROUBLESHOOTING 6 MATERIAL DISPOSAL 7 WARRANTY Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL ALIrITAIViO Ws 1 DESCRIPTION AND OPERATION 1 1 Positioner FIG 001 Fig 001 Device designed to position load forks attached to chrome bars hardened material 42CrMo4 through a sleeve welded on the fork shoulder and driven by hydraulic cylinders The forks slide on INA self lubricating bushings and are equipped with scrapers and greaser to lubricate room bushings as needed In the bottom the translation takes place through therollers fitted with grease nipples for lubrication Screws and fittings surfaces are treated to preserve them against rust A protective grid can be applied by means of bolts and washers without any welding and or drilling The connection of the hydraulic system has inputs positioned according to the type of the carriage strut The connection fittings are metric threade
6. a SI To open the forks apply pressure on Q1 To close the forks apply pressure on Q2 Left shifting operator side view Q3 Right shifting operator side view Q4 Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING E LELO JN I gv I SF F MODEL AUFRAMO Hydraulic Diagram Fig 012 Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING SXOULALOIN gv SF F MODEL AUIRAMO Table of recommended oil flow and working pressures e Fork positioner oil flow minimum 30 l min recommended 40 l min maximum 60 1 min e Hydraulic functions and recommended pressures Fork positioner pressure min 14 MPa max pressure at distributor 25 MPa shifter pressure min 12 Mpa max 22 MPa max pressure at distributor 25 MPa Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING SF F MODEL 5 TROUBLESHOOTING FAULTS 5 1 The forks do not move 5 2 Forks movement occurs too slowly 5 3 Forks movement occurs too quickly 5 4 Forks movements are not synchronized 5 5 Side shifting is not performed CAUSES There are obstacles or dirt accumulation on sliding tracks Insufficient hydraulic pressure Obstructions or breakage in the hydraulic circuit Internal leak in the cylinder worn gaskets Insufficient oil flow Obstructions in the hydraulic circuit Internal leak in the cylinder worn gaskets High oil flow There are obstacles or dirt accumulation on sliding
7. d with 24 cone DIN 3861 12L or 15L The tightness of fittings for the positioning hydraulic system is performed with an O ring anda retaining washer The hydraulic system for forks positioning is equipped with a valve to ensure a perfect synchronism of the forks 2 ASSEMBLY INSTRUCTIONS 2 1 Whole positioner Mount the positioner on the carriage plate according to the specific strut instructions Connect the system on the strut to the fittings of the equipment by tightening according to the regulations of the fittings used Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL ALIrITAIViO Ws 2 2 Hydraulic System Fig 002 2 2 1 Using flexible metal hoses equipped with end fittings connect the system on the carriage mast to equipment fittings Q1 opening forks Q2 closing forks Q3 shifting left Q4 shifting right by tightening according to the regulations of the fittings used 2 2 2 Perform some test manoeuvres to check for any leaks on hydraulic fittings soeed and movement synchronization of the forks In case of oil leakage remove the affected fittings and clean them thoroughly The synchronism of the forks is guaranteed by the valve For recommended oil flow and pressure see the table at the bottom of point 4 4 2 2 3 Perform some idle shifting movements in both directions up to the limit switch and under pressure for a few seconds Then check the seal of the hydraulic connections Disassemble and clean
8. er fork sliding roller After removing the fork see step 2 3 loosen the grub A with the 4mm Allen key Remove the pin B Remove the roller C Check the wear of bushings D and replace if necessary Once thoroughly cleaned reassemble following all above operations in reverse order Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL ALIrITAIViO Ws 4 3 5 Replacing the Fork Moving Cylinder Gaskets Fig 011 tee CO Ge Gre Fig 011 Det A After performing one or more operations specified at point 4 3 2 and or 4 3 3 Unscrew the cap cs05 with a spanner wrench and remove it along with the stem cs02 as well as CS03 CS04 and CS06 from the cylinder housing Replace gaskets cs01 cs03 cs04 cs06 The reassembly of the cylinder is performed following the reverse order of above operations paying particular attention to cleaning and checking the exact orientation of the gaskets cs03 cs04 cs06 Det A The same method for gasket replacement applies to the right cylinder as seen by the truck operator Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL ALIrITAIViO Ws 4 3 6 Restoring the Equipment After any maintenance restore the equipment to the original condition and run the tests referred to in step 2 5 4 4 HYDRAULIC SYSTEM DIAGRAM positioning forks Fig 012
9. fittings in presence of any oil leaks Tighten them according to the regulations Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL ALIrITAIViO Ws 2 3 Mounting and dismounting forks Turn off the carriage remove pressure in the supply circuit and make sure that during the operation the pump is not activated and that the distributor lever is not operated on 2 3 1 Secure the nut c with the hex wrench a on the drag ear and loosen the front nut d with the socket wrench b Fig 004 Fig 005 2 3 2 Remove the cover X loosening 4 M12 screws with 8 mm Allen key Fig 006 2 3 3 Attach the fork support with a rope 2 3 4 Remove the pin shaft Y Fig 006 2 3 5 Remove the fork Fig 006 2 3 6 For assembling bring the fork support to the correct position and insert the pin shaft Y Fig 006 2 3 7 Repeat in the opposite order the operations from step 2 3 3 to 2 3 1 Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL ALIrITAIViO Ws 2 4 Mounting the protection grid Fig 007 2 4 1 Place the grid on plates welded to the frame Bolt the grid with screws TCE M16x50 Cl 10 9 UNI 5931 DIN 912 and knurled washers 17x24 as shown Tightening torque 190Nm 133 Ft Lbs 2 5 End test operation After performing the procedures referred to in step 2 1 2 2 2 3 and if necessary 2 4 perform some side shifting movements not fork positioning movemen
10. od will be reduced proportionally The guarantee is limited to the replacement FOB the BOLZONI S p A s plant of those parts the same recognises to be defective owing to material or processing faults and does not include the labour cost or transfer cost for the replacement of such part In case the equipment has been used inappropriately has been placed in operation without following the instructions provided by BOLZONI S p A or if replacement parts have been installed that were not made by BOLZONI S p A the warranty is void BOLZONI S p A products are not guaranteed for uses beyond the performance indicated on the plates and in the documentation attached to the order All equipment manufactured by BOLZONI S p A is insured for damage or injury to third parties caused by defective parts or incorrect functioning damage or injury caused by incorrect or improper use is excluded Rev 01
11. r fork positioning with forked load and while the truck is moving Follow all the other instructions in the user manual of the truck 3 3 Prohibited Manoeuvres The equipment is not a gripper do not use the forks to hold the load by opening or closing the forks Don t use the equipment for any purpose it was not intended for Don t operate the movements control lever when the equipment is under maintenance Don t drive the truck when a large load impairs your visibility Don t tamper with the equipment Don t stand in the range of action of the equipment or truck Don t use the equipment when the structure is deformed even minimally or when it is not working properly Follow all the other instructions in the user manual of the truck Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL JIAITAINMO Ws 4 MAINTENANCE 4 1 Introduction The equipment is delivered with guides lubricated with quality grease so to ensure the normal settling and polishing of the sliding surfaces in the first period of use The user will have to grease the bearings sliding area on the chrome bar The recommended lubricant is ISO X M2 SHELL ALVANIA GREASE R2 or equivalent For the use of the equipment in a very dusty environment oil ISO 32 CB ESSO NUTO 32 or equivalent is recommended The maintenance reported below relates to the proper use of the equipment in a slightly dusty environment Rev 01 PIN TYPE FORK POSIT
12. ts up to the limit switch and keeping under pressure for a few seconds with the maximum rated load on the forks Check the perfect seal of the hydraulic connections Any small oil leaks require fitting disassembly and cleaning Tighten them according to the regulations 3 USE INSTRUCTIONS Rev 01 PIN TYPE FORK POSITIONER WITH SHIFTING LEKOL AOIN fq 2 SF F MODEL JIAITAINMO Ws 3 1 Checks and Recommendations Fork the load as centrally as possible Keep the load lifted slightly from the ground to have greater stability of the truck during the movements When moving with the truck keep the load tilted lifted fork tips Move the control levers gently to avoid sudden pressure drops on the hydraulic system thus compromising the load stability Adjust the speed of the truck based on the stability and nature of the load and any difficulties due to spaces and dimensions Pay attention to inclined planes and small differences in height since they limit the load stability Before forking adjust the position of the forks so not to force them against the feet of the pallet 3 2 Manoeuvres to be Avoided Don t move loads heavier than rated load Don t move an unstable load Don t take a load on just one fork even if it has a small weight Don t move a load to the side with a load on the forks Don t execute sudden movements or maneuvers with load forked and raised to a high level Don t perform any side shifting o
Download Pdf Manuals
Related Search