wrangler, cherokee and comanche, front axle
Contents
1. WARN INDUSTRIES INC INSTALLATION INSTRUCTIONS FOR THE WRANGLER CHEROKEE AND COMANCHE FRONT AXLE WHEEL HUB CONVERSION KIT THIS KIT IS NOT INTENDED FOR VEHICLES WITH ABS AND WILL CHANGE BOLT PATTERN TO 5 ON 5 5 Use 1980 1986 CJ7 front rotor Bendix P N 141257 Before starting be sure to machine rotor O D to 11 and hat O D to 7 See Figure 1 on page 1 As you read these instructions you will see NOTES CAUTIONS and WARNINGS Each message has a specific purpose NOTES are additional information to help you complete a procedure CAUTIONS are safety messages that indicate a potentially hazardous situation which if not avoided may result in minor or moderate injury A CAUTION may also be used to alert against unsafe practice WARNINGS are safety messages that indicate a potentially hazardous situation which if not avoided could result in serious injury CAUTIONS and WARNINGS identify the hazard indicate how to avoid the hazard and advise of the probable consequence of not avoiding the hazard PLEASE WORK SAFELY WARN INDUSTRIES INC 0 12900 SE CAPPS ROAD 0 CLACKAMAS OR 97015 8903 503 722 1200 0D CUSTOMER SERVICE LINE 1 888 722 6730 0 FAX 503 722 3051 Figure 1 CJ Rotor Diagram SAFETY PRECAUTIONS CAUTION READ INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION This sheet provides guidelines to inst2. THIS PRODUCT THE WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS ORAL OR WRITTEN EXPRESSED OR IMPLIED No Warn dealer agent or employee is authorized to make any modification extension or addition to this warranty IN NO EVENT IS WARN RESPONSIBLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR UNDER ANY OTHER LEGAL THEORY INCLUDING BUT NOT LIMITED TO LOST PROFITS DOWN TIME GOODWILL DAMAGE TO OR REPLACEMENT OF EQUIPMENT AND PROPERTY LOSS OF USE OF THE PRODUCT OR OF ANY ASSOCIATED EQUIPMENT OR COST OF SUBSTITUTED PRODUCTS Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied warranty lasts so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state Warn reserves the right to change Product design without notice or obligation to modify previously manufactured products Warranty inquires and Products returned for warranty service should be sent to WARN INDUSTRIES Customer Service Department 12900 SE Capps Road Clackamas OR 97015 1 800 543 WARN Exclusions to this Warranty Products covered by this Warranty Exclusions to this Warranty Front Hub Conversion Kits Finish u joints bearings and seals P N 38110H0 pn38109 doc 12
3. light coating of grease to the shank of the spindle Slide wheel hub assembly onto spindle NOTE Keep wheel hub aligned with spindle so bearings don t wedge on spindle Thread inner nut See Figure 3 Flag 21 on to spindle P N 38110H0 pn38109 doc 4 Using hub spindle nut socket See Figure 2 and torque wrench torque nut to 50 ft lb Rotate wheel back and forth while tightening the nut This helps seat the bearings AN WARNING Excess force can cause tool slippage or breakage and damage to the nut DO NOT OVERTORQUE NUTS Broken or slipping wrenches can cause eye or other injury 5 Loosen the nut 4 turn 90 degrees 6 Install lock washer on spindle Use care to align the pin in the inner nut with the hole in the washer The washer may be flipped if the hole does not align with the pin 7 See Figure 3 Flag 22 8 Thread outer nut on spindle See Figure 3 Flag 23 9 Torque outer nut to 125 to 150 ft lb NOTE All free clearance should be removed from the bearings If not repeat procedure HUBLOCK INSTALLATION NOTE Do not add grease to hublocks Separate body and cap assembly Figure 3 Flag 1 Push hublock body into wheel hub Figure 3 Flag 8 so lock ring groove in wheel hub is visible 3 Install large lock ring Figure3 Flag 24 into wheel hub groove Ne NOTE Ensure that large lock ring is fully seated lock ring can be removed with Plews O ring pick P N 72 017 NOTE Repeat all steps for o
4. Flag 3a Step 8 Extend vacuum actuator piston so that it is fully extended Step 9 Slide brass spacer so that it is against vacuum actuator body Step 10 Insert I small e clip so that brass collar is trapped between both the vacuum housing and the e clip Step 11 Slide engagement arm so that it is against 1 small e clip Step 12 Insert 2 small e clip so that engagement arm is trapped between both e clips Step 13 Make sure all 3 e clips are seated firmly to prevent them from falling off Step 14 Attach gear engagement ring onto spline in axle Step 15 Reattach assembled locker housing to axle housing being sure that engagement arm is seated firmly onto engagement ring Step 16 Firmly secure mounting bolts to axle housing per Jeep maintenance manual torque specifications P N 38110H0 pn38109 doc 11 WARN FRONT HUB CONVERSION PRODUCTS LIMITED LIFETIME WARRANTY FOR MECHANICAL COMPONENTS Warn Industries Inc Warn warrants that the mechanical components of the Products covered by this Warranty as specified below will be free of factory defects in material and workmanship for the lifetime of the Product This Warranty applies only to the original purchaser of the Products To obtain any warranty coverage it is absolutely necessary that you present proof of purchase and warranty period verification acceptable to Warn such as a copy of the purchase receipt If you di
5. all the WARN Front Wheel Hub Conversion Kit Figure 3 There are NOTES CAUTIONS and WARNINGS which should be followed during installation to avoid possibility of personal injury or damage to the vehicle During installation standard safety precautions and equipment should be used where appropriate Because the skill and experience of the installer and the tools used can vary widely it is impossible to anticipate all conditions under which this installation is made or to provide cautions for all possible hazards If your installation varies from the instruction you must be completely satisfied that your safety or the operation of the vehicle will not be compromised NOTE If you have questions concerning the installation of the Warn Front Axle Wheel Hub Conversion Kit call our toll free number 1 888 722 6730 for assistance APPLICATIONS The Warn Front Axle Wheel Hub Conversion Kit is designed to fit Wrangler Cherokee and Comanche Jeeps FEATURES Eliminates steering drag caused by front locking differentials in YJ s TJ s and XJ s Exclusive high strength alloy locking hubs to fit new 30 spline outer axle Serviceable bearings and seals P N 38110H0 pn38109 doc TOOLS AND MATERIALS NEEDED Jack stands 4 Lug Socket for Dana 44 Fig 2 Torque Wrench Safety Goggles 13mm 12 Pt 2 Drive Socket Shop Rags Snap on PN S8695C or similar Figure 2 4 Lug socket PARTS LIST included in kit Refer to Figu
6. can be done simultaneously l Start the engine Shift the transfer case into one of the 4WD modes Leave transfer case in the position throughout entire wheel hub conversion installation This will aid installation of the axle shafts Turn the ignition key OFF Put transmission in Park automatic or Reverse manual Set the parking brake and chock the rear wheels Raise the front end and support it on 2 jack stands Remove the tire and wheel assembly ae S WARNING Brake pads may contain asbestos NEVER CLEAN BRAKE SURFACES WITH COMPRESSED AIR AVOID INHALING ANY DUST FROM THE BRAKE SURFACE USE A COMMERCIALLY AVAILABLE BRAKE CLEANING FLUID Asbestos has been found to be a cancer causing agent 6 Remove the caliper and hang it from the frame or suspension with a piece of wire being careful not to strain the brake hose 7 Remove 3 bolts retaining the original hub using 13 mm 12 pt socket and bearing assembly Do not disassemble the bearing assembly from axle shaft See Figure 4 For location reference only NOTE Refer to your authorized Jeep Technical Service Manual for removal instructions P N 38110H0 pn38109 doc 8 Remove axle shafts brake shield hub and bearing pack See Figure 4 For location reference only P N 38110H0 pn38109 doc WE A 2 rq A aes io CEN OREA HINN ld lo N ff ff __ rol at f UMW I A Os ry a Figure 4 Exploded knu
7. ckle NOTE Be careful not to damage inner differential seal Press parts under stress can break WEAR SAFETY GOGGLES Broken parts can cause eye injury 9 Separate the original inner shaft from the outer shaft by removing the u joint NOTE Refer to your authorized Jeep Technical Service Manual for removal instructions 10 Install shield to outer axle shaft both components supplied with kit See Figure 5 Be sure that seal shield is seated firmly against axle Figure 5 Stub axle and seal shield 11 Install u joint and outer axle shaft both supplied in kit to inner axle shaft 12 While supporting axle assembly to keep from pushing loose material into differential slide axle assembly into differential being careful not to damage the inner seal P N 38110HO0 pn38109 doc 13 Place thrust washer I D chamfer side towards Yoke See Figure 3 Flag 16 14 Place V seal thick side towards yoke on axle shaft See Figure 3 Flag 17 NOTE Put grease in counter bore Be sure that factory installed spindle seal is placed cup side facing away from needle bearing This seal is held in by grease only See figure 3 Flag 15 15 Clean mating surfaces between steering knuckle and spindle 16 Place dust shield on to the steering knuckle 17 Place spindle over outer axle shaft and bolt on to steering knuckle Torque 3 bolts to 75 ft lbs See Figure 4 ROTOR TO WHEEL HUB INSTALLATION 1 Place spacer and
8. ent on the wheel stud The minimum amount of engagement is equal to the diameter of the stud If the minimum amount of engagement is not achieved then it is possible to use special AMERICAN RACING Lug nuts P N 831142 1 2 20 Acorn Shank to help achieve the minimum amount required Itis the installers responsibility to check lug nut compatibility and engagement 5 Lift vehicle Remove jack stands Lower vehicle to ground 6 Torque lug nuts per manufacturer s specifications WARNING After 50 miles re torque lug nuts to manufactures specifications Always re torque lug nuts after hard trail use OPTIONAL Permanent Engagement of Vacuum Actuator OPTIONAL To secure axle shaft engagement permanently you may elect to complete the following Step I Remove vacuum actuator from front axle assembly P N 38110H0 pn38109 doc 10 Figure 8 Step 2 Remove 3 e clips from inside actuator housing as shown in Figure 8 See Flag 1A 2A and 3A Step 3 Slide out vacuum actuator form actuator housing Figure 8 Flag5 Step 4 Slide brass spacer on to vacuum actuator piston Figure 8 Flag 4 Step 5 Insert shift fork arm into housing being sure that arm is facing in the correct position Figure 8 Flag 2 Step 6 Insert vacuum actuator with brass spacer into housing being sure to slide through shift fork Figure 8 Flag 4 and 5 Step 7 Snap in large e clip on to vacuum actuator housing in area indicated Figure 8
9. re 3 for Item Item Part Name Qty Other P N 2 indle 2 LM102949 86 2 8 WheelHub 2 086990 a ae 2 AFBMA bearing P N CR Services P N Russell P N Spicer P N Bendix P N 2 Needle Bearing 2 550759 2 nner Bearing Cup 2 LM102910 Spindle 62569 2 2 NOTE Item numbers 14 17 replacements can be purchased in kit form from Spicer using the following part number 706527X 2 Required P N 38110H0 pn38109 doc CG amp Cp Figure 3 Front axle wheel hub conversion kit Parts not included in kit are drawn with dashed lines P N 38110HO0 pn38109 doc WARNING Raised vehicles can cause falling particles WEAR SAFETY GOGGLES Falling particles can cause eye injury Improperly supported vehicles can fall DO NOT USE A JACK TO SUPPORT THE VEHICLE USE JACK STANDS IN PAIRS TO SUPPORT THE VEHICLE USE JACKS OR JACK STANDS ONLY ON A HARD STABLE AND LEVEL SURFACE DO NOT EXCEED THE RATED CAPACITY OF A JACK OR JACK STANDS An unstable vehicle can fall and cause a crushing injury A rolling vehicle can cause jackstands to tip Before working under vehicle VERIFY THAT THE PARKING BRAKE IS SET THE TRANSMISSION IS IN PARK AUTOMATIC OR REVERSE MANUAL AND THE REAR WHEELS ARE CHOCKED A tipping jackstand or vehicle can cause injury DISASSEMBLY NOTE The following instructions are for doing one side of the axle Both sides of the axle
10. scover a covered defect Warn will at its option repair replace or refund the purchase price of the Product or component parts at no charge to you provided you return it during the applicable warranty period transportation charges prepaid to Warn Industries Service Department or Factory Authorizes Servicing Distributor You can obtain additional information from Warn directly at the address printed below Please attach your name address telephone number a description of the problem and a copy of the bill of sale bearing the appropriate Warn serial numbers as proof of original retail purchase to each product returned for warranty service Exclusions from this warranty are those specified below This warranty applies only to Products manufactured by Warn which are sold bearing the Warn trademark This warranty does not apply i to the parts or components expressly excluded below or ii if the Product has been damaged by accident abuse misuse collision overloading exhaust misapplication improper installation improper service or modification without written permission from Warn EXCEPT AS EXPRESSLY STATED HEREIN THERE ARE NO WARRANTIES EXPRESS OR IMPLIED INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WHICH BY LAW MAY NOT BE EXCLUDED IS LIMITED IN DURATION TO ONE 1 YEAR FROM THE DATE OF ORIGINAL RETAIL PURCHASE OF
11. the brake rotor on the wheel hub aligning the holes See Figure 6 2 Press the studs into the holes NOTE Make sure head of stud firmly contacts the brake rotor flange SPALER Figure 6 Stud press diagram BEARING INSTALLATION 1 Inspect inside of wheel hub and clean if necessary See Figure 3 Flag 8 2 Pack wheel hub inner diameter Figure 7 Flag 4 with wheel bearing grease 3 Apply a coating of grease to the inside diameter of the bearing cups P N 38110H0 pn38109 doc D Pack the inner wheel bearing cone LM102949 with wheel bearing grease Use a wheel bearing packer if possible To pack by hand place a large amount of grease in the palm of your hand and force the edge of the bearing into the grease so that it fills with grease Continue until the whole bearing is coated with grease Apply additional grease with fingers Install packed bearing into cup on inboard side of wheel hub Figure 7 Flag 1 Apply additional grease around back side of installed bearing Figure 7 Flag 2 Fill large radial seal cavity with grease Press large radial seal into seat of inboard side of wheel hub Figure 7 Flag 2 Seal may protrude slightly from wheel hub Figure 7 Bearing and seal installation 8 9 Pack outer bearing LM501349 with grease using the same technique described in step 4 Install outer bearing Figure 7 Flag 3 WHEEL HUB INSTALLATION 1 2 3 Apply a
12. ther side of vehicle 4 Using snap ring pliers install axle retaining ring Figure 3 Flag 2 NOTE If necessary a pry bar can be inserted into knuckle u joints to hold axle shaft out board while installing the axle retaining ring 5 Grease o ring on cap NOTE Dial hub lock cap Figure 3 Flag 1 to FREE position 6 Place hub lock cap on body P N 38110H0 pn38109 doc 7 Install small o rings on cap screws 8 Align holes on cap using one socket head cap screw Figure 3 Flag 1 as pilot 9 Insert remaining 5 cap screws Torque to 25 30 INCH lb 10 Re install brake caliper Refer to Jeep service manual HUBLOCK CHECK 1 To check for proper engagement dial both hub locks to LOCK Spin one axle NOTE For an open differential the opposite axle will reverse rotate if the hub locks are engaging properly For a locking differential the drive line and opposite axle will turn if the hub locks are engaging properly 2 To check for proper disengagement dial one hub lock to FREE and spin the same axle NOTE For a locking differential if the drive line does not turn and there are no ratcheting sounds the hub lock is disengaging properly For an open differential if the opposite axle does not turn and there are no ratcheting sounds the hub lock is disengaging properly 09 Repeat steps 1 and 2 for opposite hub lock 4 Install wheels and tires Snug lug nuts WARNING Check lug nuts for proper amount of thread engagem
Download Pdf Manuals
Related Search