2001 LEGACY SERVICE MANUAL QUICK REFERENCE INDEX
Contents
1. B4M1787 4 1786 3 Tighten self locking nut Tightening torque 120 N m 12 2 kgf m 88 ft lb RS 11 WHEEL ALIGNMENT Rear Suspension 4 THRUST ANGLE S201116A1004 e Inspection 1 Position vehicle on a level surface 2 Move vehicle 3 to 4 meters directly forward 3 Determine locus of both front and rear axles 4 Measure distance L between center line of loci of the axles Thrust angle Less than 30 when L is equal to or less than 23 mm 0 91 in 4 S4M0350B 1 Center line of loci front axle 2 Center line of loci rear axle e Adjustment 1 Make thrust angle adjustments by turning toe in adjusting bolts of rear suspension equally in the same direction 2 When one rear wheel is adjusted in a toe in direction adjust the other rear wheel equally in toe out direction in order to make thrust angle adjustment 3 When left and right adjusting bolts are turned incrementally by one graduation in the same direction the thrust angle will change approxi mately 10 L is almost equal to 7 5 mm 0 295 in Thrust angle 0 30 WWC 0 S4M0350B 1 Center line of loci front axle 2 Center line of loci rear axle NOTE Thrust angle refers to a mean value of left and right rear wheel toe angles in relation to vehicle body center line Vehicle is driven straight in the thrust angle direction while swinging in the2. Used as an adapter for camber amp caster gauge when measuring camber and caster 1 28199 000 PLATE 2 28199AC010 BOLT Used for replacing link rear bushing B4M2380 20099AE010 INSTALLER amp REMOVER Used for replacing link upper bushing B4M2381 20099AE020 INSTALLER amp REMOVER RS 6 Used for replacing rear arm front bushing ILLUSTRATION GENERAL DESCRIPTION TOOL NUMBER DESCRIPTION Rear Suspension REMARKS B4M2382 B4M2383 20099AE040 INSTALLER amp REMOVER 20099AE030 HELPER SOCKET WRENCH Used for replacing rear arm rear bushing Used for replacing helper amp B4M2384 927760000 STRUT MOUNT SOCKET 2 GENERAL PURPOSE TOOLS TOOL NAME REMARKS Alignment Gauge Used for wheel alignment measurement Turning Radius Gauge Used for wheel alignment measurement Used for disassembling and assembling strut and shock mount Used for toe in measurement Used for suspension assembly disassembly Bearing Puller Used for removing bushings RS 7 WHEEL ALIGNMENT Rear Suspension 2 Wheel Alignment s A INSPECTION 201116A10 Check adjust and or measure wheel alignment in accordance with procedures indicated in figure WHEEL ARCH HEIGHT FRONT AND REAR CAMBER FRONT AND REAR CASTER FRONT FRONT TOE IN REAR TOE IN THRUST ANGLE REAR WHEEL STEERING ANGLE
3. B4M1088A RS 8 WHEEL ALIGNMENT Rear Suspension 1 WHEEL ARCH HEIGHT 1 Adjust tire pressure to specifications 2 Set vehicle under curb weight conditions Empty luggage compartment install spare tire jack ser vice tools and top up fuel tank 3 Set steering wheel in a wheel forward position 4 Suspend thread from wheel arch point A in figure below to determine a point directly above center of spindle 5 Measure distance between measuring point A and center of spindle Outer rear quarter Wheel arch height Wheel arch height Cross section of arch 3 2 o Front wheel arch height Rear wheel arch height Wheel arch height End of spindle B4M1783A Model Specified wheel arch height Sedan 371 mm 14 61 947 55 in Wagon 381 12 mm 15 00 977 in OUTBACK 421 12 mm 16 57 9 7 0 in RS 9 WHEEL ALIGNMENT Rear Suspension 2 CAMBER 5201116 1002 Inspection 1 Place front wheel on turning radius gauge Make sure ground contacting surfaces of front and rear wheels are set at the same height 2 Set ST into the center of the wheel and then install the wheel alignment gauge ST 927380002 ADAPTER B4M0567B 1 Alignment gauge 2 Turning radius gauge NOTE Refer to the SPECIFICATIONS for the camber values Ref to RS SPECIFICATIO
4. gt 3 Remove bolt securing parking brake cable clamp to rear arm B4M1793 8 Remove nut securing stabilizer link to rear arm KO Bi B4M1790 RE 4 Remove bolt securing brake hose to rear arm p S a B4M1871 gt lt 26 oe 9 Remove bolt securing shock absorber to rear md 4 1791 5 Remove bolt securing ABS sensor to rear arm PI C L B4M1794 10 Use transmission jack to support rear arm horizontally A FX B4M1792 6 Using a flare nut wrench disconnect brake pipe from wheel cylinder Drum brake model only CAUTION Cover open end of wheel cylinder and pipe to prevent entry of foreign particles B4M1795 RS 15 REAR ARM Rear Suspension 11 Remove bolt securing rear arm to body B INSTALLATION 1 Use a transmission jack to support the rear arm 2 Install rear arm and temporarily tighten bolts securing rear arm to links 3 Install bearing unit Ref to DS 24 INSTALLATION Hub Unit Bear ing 4 Install bolt securing ABS sensor to rear arm 5 Install bolt securing brake hose to rear arm 6 Install bolt securing parking brake cable clamp 12 Loosen nut securing front rink to rear arm 7 Place jack furnished with vehicle upside down and position it between link rear and sub frame Adjust jack position so rear shock absorber is aligned
5. into trailing link ST A 20099AE020 INSTALLER amp REMOVER SET 1 Set ST A in position with smaller inside diameter side facing up 2 Set rear arm in position with outer side of vehicle body facing down 3 Place bushing on upper side of rear arm 4 Place ST B on upper side of bushing then press bushing into position CAUTION e Install bushing with painted side facing up e Install front bushing in the proper direction as shown in figure B4M1803A B4M1802B 1 Bushing RS 17 REAR ARM Rear Suspension 2 REAR BUSHING 520110540202 E INSPECTION S201105A10 1 Using ST C D and bearing puller press bush Check trailing links for bends corrosion or dam ing into trailing link age ST C D 20099AE040 INSTALLER amp REMOVER SET 1 Insert bushing into bore in ST D 2 Set ST C ST D and bearing puller in position as shown in the figure and press bushing into position B4M1804B RS 18 LINK UPPER 5 Link Upper so A REMOVAL 201103A18 1 Loosen wheel nuts Lift up vehicle and remove wheel 2 Use transmission jack to support rear arm hori zontally B4M1806B 1 Rear arm 2 Transmission jack 3 Remove bolt securing link upper to sub frame i B4M1875 4 Remove bolts which secure link upper to rear arm and detach link upper B4M1857 Rear Suspension B INSTALLATION Install in the re
6. oblique direc tion depending on the degree of the mean thrust angle B4M0193B 1 Front 2 Thrust angle 3 Body center line RS 12 WHEEL ALIGNMENT Rear Suspension Thrust angle r B 2 Right rear wheel toe in angle B Left rear wheel toe in angle NOTE Here use only positive toe in values from each wheel to substitute for o and in the equation 1 2 B4M0194B 1 Front 2 Body center line RS 13 REAR STABILIZER Rear Suspension 3 Rear Stabilizer lt A REMOVAL 5201118 18 1 Jack up the rear part of the vehicle support it with safety stands rigid racks 2 Remove bolts which secure stabilizer link to rear arm B4M1874 3 Remove bolts which secure stabilizer to sub frame B4M1851 B INSTALLATION ss Install in the reverse order of removal Tightening torque Stabilizer link to rear arm 44 N m 4 5 kgf m 32 5 ft Ib Clamp to sub frame 40 N m 4 1 kgf m 30 ft Ib C INSPECTION 5201118410 1 Check bushing for cracks fatigue or damage 2 Check stabilizer links for deformities cracks or damage and bushing for protrusions from the hole of stabilizer link RS 14 REAR ARM Rear Suspension 4 Rear Arm 7 Suspend the back plate from sub frame A REMOVAL S201105A18 ee MO 1 Lift up the vehicle and remove rear wheel 2 Remove bearing unit lt Ref to DS 22 REMOVAL Hub Unit Bearing
7. 17 ASSEMBLY Front Strut gt RS 22 REAR SHOCK ABSORBER Rear Suspension E INSPECTION 5201104 10 1 Refer to Front Strut as guide for inspection procedures lt Ref to FS 18 INSPECTION Front Strut gt 2 If vehicle is equipped with self leveling suspension check the following CHECK WHEEL ARCH HEIGHT Is B between 411 mm Go to step 2 Replace shock 1 Remove all cargo from the vehicle 16 18 in and 391 mm absorber 2 Fill gasoline tank completely 15 39 in 3 Drive vehicle only the driver aboard for at least 1 km 0 6 mile 4 Measure the rear wheel arch height This is value A in the equation Ref to RS WHEEL ARCH HEIGHT INSPECTION Wheel Alignment gt 5 Put 4 people in the vehicle NOTE The total weight of the 4 people should be approximately 300 kg 662 Ib 6 Drive the vehicle for at least 5 km 3 miles 7 Stop the vehicle With the 4 people in the vehicle measure the rear wheel arch height This value is B in the equation CHECK WHEEL ARCH HEIGHT Is D less than 10 mm Go to step 3 Replace shock 1 Let the 4 people get off of the vehicle 0 39 in absorber 2 Drive the vehicle only the driver aboard for at least 1 km 0 6 mile 3 Measure the rear wheel arch height This is value C in the equation 4 A C D CHECK WHEEL ARCH HEIGHT Is C between 433 mm Replace coil 17 05 in and 397 mm spring 15 63 in RS 23 REAR SHOCK ABSORBER Re
8. 2001 LEGACY SERVICE MANUAL QUICK REFERENCE INDEX SUPPLEMENT FOR 6 CYLINDER ENGINE MODEL FOREWORD HOW TO USE THIS MANUAL SPECIFICATIONS PRECAUTION This service manual has been prepared to provide SUBARU service personnel with the necessary infor mation and data for the correct maintenance and repair of SUBARU vehicles This manual includes the procedures for maintenance disassembling reassembling inspection and adjust ment of components and diagnostics for guidance of experienced mechanics Please peruse and utilize this manual fully to ensure complete repair work for satisfying our customers by keeping their vehicle in optimum condition When replacement of parts during repair work is needed be sure to use SUBARU genuine parts NOTE IDENTIFICATION RECOMMENDED MATERIALS PRE DELIVERY INSPECTION PERIODICAL MAINTENANCE All information illustration and specifications con tained in this manual are based on the latest product information available at the time of publication approval FUJI HEAVY INDUSTRIES LTD G2281GE 2001 LEGACY SERVICE MANUAL SUPPLEMENT FOR 6 CYLINDER ENGINE MODEL QUICK REFERENCE INDEX FUEL INJECTION FUEL SYSTEMS FU H6 EMISSION CONTROL AUX EMISSION CONTROL DEVICES EC H6 INTAKE INDUCTION IN H6 MECHANICAL ME H6 EXHAUST EX H6 COOLING CO H6 LUBRICATION LU H6 SPEED CONTROL SYSTEMS SP H6 IGNITION IG H6 START CHARGING
9. ERAL DESCRIPTION Rear Suspension C CAUTION 5201001 03 e Wear working clothing including cap protec tive goggles and protective shoes during opera tion e Remove contamination including dirt and corro sion before removal installation or disassembly e Keep the disassembled parts in order and pro tect them from dust or dirt e Before removal installation or disassembly be sure to clarify the failure Avoid unnecessary removal installation disassembly and replace ment e Use SUBARU genuine grease etc or the equivalent Do not mix grease etc with that of another grade or from other manufacturers e Be sure to tighten fasteners including bolts and nuts to the specified torque e Place shop jacks or safety stands at the speci fied points e Apply grease onto sliding or revolution surfaces before installation e Before installing O rings or snap rings apply sufficient amount of grease to avoid damage and deformation e Before securing a part on a vise place cushion ing material such as wood blocks aluminum plate or shop cloth between the part and the vise e Before disposing shock absorbers be sure to bleed gas completely Also do not throw away in fire RS 5 Rear Suspension GENERAL DESCRIPTION D PREPARATION TOOL 1 SPECIAL TOOLS 5201001 1701 ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS B4M2379 927380002 20099AE000 ADAPTER INSTALLER amp REMOVER
10. N e Using transmission jack support rear arm horizontally install link front and tighten nuts to specified torque B4M1806B 1 Rear arm 2 Transmission jack e Install link front with protruded side facing front SY QU 1 SW B4M1849B 1 Front e Replace self locking nut NOTE Check wheel alignment and adjust if necessary INSPECTION 5201106 10 Visually check link front for damage or bends RS 25 LINK REAR Rear Suspension 8 Link Rear son A REMOVAL 5201102 18 1 Loosen wheel nuts Lift up vehicle and remove wheel 2 Remove bolt securing stabilizer clamps to sub frame B4M1851 3 Remove support sub frame RH When remov ing RH side link rear B4M1852 B4M1874 5 Use transmission jack to support rear arm hori zontally B4M1806B 1 Rear arm 2 Transmission jack 6 Remove bolt securing link rear to rear arm B4M1873 7 Scribe an alignment mark on link rear adjusting bolt and sub frame 8 Remove bolts securing link rear to sub frame detach link rear CAUTION To loosen adjusting bolt always loosen nut while holding the head of adjusting bolt B4M1853 RS 26 LINK REAR B INSTALLATION Install in the reverse order of removal observing the following instructions CAUTION e Using transmission jack support rear arm horizontally install link
11. NS General Description gt e Front Camber Adjustment Refer to FS section for front camber adjustment lt Ref to FS 6 INSPECTION Wheel Alignment gt 3 WHEEL TOE IN 5201116 1003 Inspection 1 Using toe in gauge measure rear wheel toe in Toe in 0 3 00 12 in 2 Mark rear sides of left and right tires at height corresponding to center of spindles and measure distance A between marks 3 Move vehicle forward so that marks line up with front sides at height corresponding to center of spindles 4 Measure distance B between left and right marks Toe in can then be obtained by the follow ing equation A B Toe in e Adjustment 1 Loosen self locking nut on inner side of link rear CAUTION e When loosening or tightening adjusting bolt hold bolt head and turn self locking nut e Discard loosened self locking nut and replace with a new one H4M1279B B4M1785B 1 Adjusting bolt 2 Link rear 2 Turn adjusting bolt head until toe in is at the specification RS 10 WHEEL ALIGNMENT Rear Suspension NOTE When left and right wheels are adjusted for toe in at the same time the movement of one scale gradua tion changes toe in by approximately 3 mm 0 12 in Left side Right side T Rotat nterclock Toe in is increased Rotate clockwise COUNISTEIRG Toe in is decreased Rotate Rotate clockwise
12. SYSTEMS SC H6 ENGINE DIAGNOSTICS EN H6 REAR SUSPENSION 2 2 WIRING SYSTEM G2281GE REAR SUSPENSION RS Page 1 4529 aea AE rari AER 2 Wheel Alignment te sais T m m d Rear SISbIZBE cip rta cq eH dec CU Gre a mE ERR 14 Bis ctt erect er edi e E Rr aks 45 EE d c 49 6 Rear Shock Absorber sisi coe mecs conste ticae errans ca ew SEE CURRO EU d bil 7 ULM 25 re tere mm pct erede eod 28 8 hear Sub Frame acre ieri A un HM tere RU aU C E 28 10 EL 2g 11 General Diagnostic Table re retener 30 GENERAL DESCRIPTION Rear Suspension 1 General Description s A SPECIFICATIONS OUTBACK Camber tolerance 0 45 0 20 0 3 mm 0 0 12 in Each toe in angle 0 15 Wheel arch height 371 mm 381 mm 421 mm tolerance 7 _ mm 47 _ 9 in 14 61 in 15 00 in 16 57 in Thrust angle 0 30 2 0 L Wagon model 15 mm 0 59 in Diameter of stabilizer Except 2 0 L Wagon model 14 mm 0 55 in NOTE e Front and rear toe ins and front camber can be adjusted If toe in or camber tolerance exceeds specifications adjust toe in and camber to the middle value of specification e The other items indicated in the specification table cannot be adjusted If the other items exceeds specifications check suspen
13. ar Suspension F DISPOSAL 5201104407 CAUTION e Completely discharge the gas from the shock absorber before disposal Follow the disposal procedure outlined below e Do not disassemble shock absorber or place into a fire e Drill holes before disposing of shock absorber e Before handling shock absorber be sure to wear goggles to protect eyes from gas oil and or filings 1 Place shock absorber on a flat and level sur face with piston rod fully extended 2 Using a 2 to 3 mm 0 08 to 0 12 in dia drill drill 30 mm 1 18 in deep holes in areas shown in the figure Without self leveling suspension ge 40 mm 1 57 in G 4 1864 Wi th self leveling suspension B 50 mm 1 97 in 100 mm 3 94 in B4M1865B RS 24 LINK FRONT 7 Link Front A REMOVAL 5201106 18 1 Loosen wheel nuts Lift up vehicle and remove wheel 2 Use transmission jack to support rear arm hori zontally B4M1806B 1 Rear arm 2 Transmission jack 3 Remove bolt securing link front to sub frame B4M1872 4 Remove bolts which secure link front to rear arm and detach link front B4M1848 NOTE Link front bushing cannot be replaced alone Always replace link front and bushing as a single unit Rear Suspension B INSTALLATION szorosan Install in the reverse order of removal observing the following instructions CAUTIO
14. htening torque of rear dif ferential With T type Ref to DI 25 INSTALLATION Rear Differential for T type gt With VA type Ref to 01 43 INSTALLATION Rear Differential for VA type gt 3 Using transmission jack support rear arm hori zontally and tighten nuts and bolts securing rear arm link front link rear link upper and shock absorber B4M1806B 1 Rear arm 2 Transmission jack NOTE Check wheel alignment and adjust if necessary C INSPECTION 201111A10 Check removed parts for wear damage and cracks and correct or replace if defective RS 28 HELPER 10 Helper ss A REMOVAL 5201539 18 1 Jack up the rear part of the vehicle support it with safety stands rigid racks 2 Using ST remove helper ST 20099AE030 HELPER ST SY B4M1867A B INSTALLATION Install in the reverse order of removal Tightening torque 30 N m 3 1 kgf m 22 ft Ib C INSPECTION 5201539 10 Check helper for cracks fatigue or damage RS 29 Rear Suspension GENERAL DIAGNOSTIC TABLE Rear Suspension 11 General Diagnostic Table gt A INSPECTION 1 IMPROPER VEHICLE POSTURE OR IMPROPER WHEEL ARCH HEIGHT 1 Permanent distortion or breakage of coil spring Replace 2 Unsmooth operation of damper strut and or shock absorber Replace 3 Installation of wrong strut and or shock absorber Replace with proper parts 4 Installation of wrong coil sp
15. r arm B4M1862 6 Use a jack to support the shock absorber RS 21 REAR SHOCK ABSORBER Rear Suspension B INSTALLATION sonnn 1 Use a jack to support the shock absorber 2 Tighten self locking nut used to secure shock absorber to vehicle body CAUTION Use a new self locking nut Tightening torque 30 N m 3 1 kgf m 22 ft Ib 3 Place jack furnished with vehicle upside down and position it between link rear and sub frame Adjust jack position so rear shock absorber is aligned with rear arm at their corresponding holes Install lower shock absorber bolts CAUTION Put a cloth between jack and its mating area to protect link rear and sub frame from scratches B4M1805 4 Using transmission jack support rear arm hori zontally and tighten shock absorber nuts and bolts to specified torque B4M1806B 1 Rear arm 2 Transmission jack Tightening torque 160 N m 16 3 kgf m 118 ft Ib CAUTION Use a new self locking nut 5 Install floor mat Wagon model 6 Set trunk side trim Sedan model 7 Install trunk mat Sedan model NOTE Check wheel alignment and adjust if necessary DISASSEMBLY 201104A06 For disassembly of shock absorber refer to proce dures outlined under front strut as a guide lt Ref to FS 16 DISASSEMBLY Front Strut gt D ASSEM B LY 5201104402 Refer to Front Strut as a guide for assembly cedures lt Ref to FS
16. rear and tighten nuts to specified torque B4M1806B 1 Reararm 2 Transmission jack e Tighten nut when installing adjusting bolt e Replace self locking nut NOTE Check wheel alignment and adjust if necessary C DISASSEMBLY 201102A06 Using ST A B press bushing out of place ST A 20099AE000 INSTALLER amp REMOVER B4M1854B Rear Suspension D ASSEM B LY 5201102402 Using ST press bushing into place ST A B 20099AE000 INSTALLER 8 REMOVER B4M1854B E INSPECTION 201102A10 Visually check link rear for damage or bends RS 27 REAR SUB FRAME Rear Suspension 9 Rear Sub Frame ssn A REMOVAL S201111A18 1 Separate front exhaust pipe and rear exhaust pipe 2 Remove rear exhaust pipe and muffler 3 Remove rear differential With T type Ref to 01 23 REMOVAL Rear Differential for T type With VA type Ref to 01 41 REMOVAL Rear Differential for VA type 4 Disconnect link front from sub frame Ref to RS REMOVAL Link Front 5 Disconnect link rear from sub frame Ref to RS 26 REMOVAL Link Rear 6 Disconnect link upper from sub frame Ref to 5 19 REMOVAL Link Upper 7 Place transmission jack under sub frame B4M1870 8 After removing bolts remove sub frame and support sub frame from vehicle body B INSTALLATION 1 Install in reverse order of removal 2 For installation and tig
17. ring Replace with proper parts 2 POOR RIDE COMFORT 8201257 1002 1 Large rebound shock 2 Rocking of vehicle continues too long after running over bump and or hump 3 Large shock in bumping Possible causes Countermeasures Replace Adjust Adjust or replace coil springs with new ones Replace Replace Replace with proper parts Deformation or loss of bushing Replace Deformation or damage of helper in strut assembly and or shock Replace absorber 9 Oil leakage of damper strut and or shock absorber Replace 3 NOISE 5201257 1003 Possible causes Countermeasures 1 Wear or damage of damper strut and or shock absorber component parts 2 Loosening of suspension link installing bolt Retighten to the specified torque 3 Deformation or loss of bushing 4 Unsuitability of maximum and or minimum length of damper strut Replace with proper parts and or shock absorber 5 Breakage of coil spring Replace 6 Wear or damage of ball joint 7 Deformation of stabilizer clamp RS 30
18. sion parts and connections for deformities replace with new ones as required Toe in B4M2250C 1 Front A B Positive Toe in Negative Toe out 01 a2 Each toe in angle RS 2 GENERAL DESCRIPTION Rear Suspension B COMPONENT 201001A05 1 REAR SUSPENSION S201001A0501 B4M1782B Shock absorber Self locking nut 15 Hub bearing unit 16 Helper Tightening torque N m kgf m ft Ib 3 Stabilizer 17 Link upper 2 on 4 Stabilizer bushing 18 Link upper bushing Inside a 5 Clamp 19 Link upper bushing Outside T3 44 4 5 32 5 6 Stabilizer link 20 Link front T4 65 6 6 48 7 Link rear 21 Rear sub frame T5 110 11 2 81 8 Adjusting bolt 22 Support sub frame RH T6 120 12 2 88 9 Link rear bushing 23 Support sub frame LH T7 150 15 3 111 10 Adjusting washer 24 Stopper upper Except OUT T8 160 16 3 118 11 Rear arm BACK model T9 175 17 8 129 12 Rear arm rear bushing 25 Stopper upper OUTBACK 13 Rear arm front bushing MODEL 14 Rear arm bracket 26 Stopper lower RS 3 GENERAL DESCRIPTION Rear Suspension 2 SHOCK ABSORBER 520100140502 B4M1860A 1 Mount 5 Shock absorber Tightening torque N m kgf m ft Ib 2 Rubber seat upper 6 Self locking nut T1 30 3 1 22 4 3 Dust cover T2 35 3 6 26 4 Coil spring ied T3 160 16 3 118 RS 4 GEN
19. verse order of removal observing the following instructions CAUTION e Using transmission jack support rear arm horizontally install link upper and tighten nuts to specified torque B4M1806B 1 Rear arm 2 Transmission jack e Tighten nut when installing adjusting bolt e Replace self locking nut NOTE Check wheel alignment and adjust if necessary RS 19 LINK UPPER Rear Suspension C DISASSEMBLY S201103A06 D ASSEMBLY S201103A02 Using ST press bushing out of place 1 Using ST press bushing into place ST 20099AE010 INSTALLER amp REMOVER ST 20099AE010 INSTALLER amp REMOVER CAUTION Outer bushing has a directional design Be sure to install bushing with longer inner hous ing side facing vehicle rear B4M1858A B4M1859A E INSPECTION S201103A10 Visually check link upper for damage or bends RS 20 REAR SHOCK ABSORBER Rear Suspension 6 Rear Shock Absorber sn 7 Remove nuts securing shock absorber mount to body A REMOVAL 5201104418 e Wagon 1 Lift up vehicle and remove rear wheels 2 Remove clip and detach floor mat Wagon E ee Wt 2 p B4M1863 e Sedan B4M1861 3 Detach trunk mat Sedan model 4 Roll up the trunk side trim Sedan model eo oe B4M2176 8 Remove shock absorber B4M2175B 1 Trunk side trim 5 Remove bolt securing shock absorber to rea
20. with rear arm at their corresponding holes Install lower shock absorber bolts CAUTION Put a cloth between jack and its mating area to protect link rear and sub frame from scratches B4M1797 13 Loosen nut securing rear link to rear arm B4M1805 8 Using transmission jack support rear arm hori zontally and tighten nuts and bolts securing rear arm link front link rear link upper and shock absorber B4M1798 14 Loosen nut securing upper link to rear arm B4M1806B 1 Rear arm Transmission jack B4M1799 2 NOTE Check wheel alignment and adjust if necessary 15 Remove bolts securing rear arm to links and remove rear arm RS 16 REAR ARM G DISASSEMBLY 201105A06 1 FRONT BUSHING 5201105 0601 1 Using ST A press front bushing out of place ST A 20099AE020 INSTALLER amp REMOVER SET 1 Set ST A in position with larger inside diam eter side facing up 2 Set rear arm with protruded bushing side facing down 3 Place ST B on upper side of bushing then press bushing out of position B4M1800A 2 REAR BUSHING Using ST C and bearing puller press rear bushing out of place ST C 20099AE040 INSTALLER amp REMOVER SET B4M1801B 1 Bearing puller Rear Suspension D ASSEMBLY 8201105 02 1 BUSHING 5201105 0201 1 Using B press bushing
Download Pdf Manuals
Related Search