TEST & SET MODES - Janome Service Videos
Contents
1. Janome model s MC200E Elna model s 8100 Screen Calibration While holding down the Start Stop button turn on the machine and let go when you enter the test mode Now press the Start Stop button Upgrading With the USB stick already inserted turn on the machine Press and release the Start Stop button once when prompted Janome model s MC7700QCP Elna model s 740 Self Check Needle Up Down amp Lock Stitch gt Turn Jog Dial to 3 Self Check gt Press Reverse Button for Each Step Test Mode While holding down the Needle Up Down amp Lockstitch buttons turn on the machine Release the buttons once you see icons on the screen Turn the jog dial to highlight the option and press the jog dial button to select it Press the reverse button to go back to the main menu for most steps Screen Calibration Needle Up Down amp Lock Stitch gt Turn Jog Dial to 2 TTP Coordinate gt Press Each Indicated Button Crosshair gt Press the Jog Dial Button to Save it Reset Memory to Factory Default Needle Up Down amp Lock Stitch gt Turn Jog Dial to 5 Initialize EEPROM gt Press the Jog Dial Button to Save it Janome model s MC6600P Elna model s 7300 Test Mode While holding the Needle Up Down amp Lockstitch buttons turn on the machine then let go when you enter the test mode Step 1 Self Check Step 2 Step 3 Erase EEPROM M Yes Press M to reset all settings amp saved stitches in2. Step2 Key Buttons The LCD will display the name of each button as you press and hold each one Step3 Switch Bobbin winder Step4 Sensor Buttonhole amp upper shaft sensor check BH Buttonhole sensor Remove any foot you have on the machine When the buttonhole lever is all of the way down the LCD display will read L and H when the lever is touched or in the up position BS Upper shaft sensor check zigzag mode When the needle bar is up the LCD will display H and L when the needle bar is not in the highest position FS Upper shaft sensor check feed step mode When the needle bar is up the LCD will display L and H when the needle bar is not in the highest position Step5 VeloSen Velocity check The display will change numbers as you turn the hand wheel backwards Step6 Speed contro check Step7 Foot controller check Step8 Zigzag amp Feed Step Motor Check Press MEM to calibrate each motor depending on if the needle is up or down Step9 DC Motor Check Janome model s JP760 JP720 AQS2009 JNH720 Janome model s DC4030PR DC4030 Test mode Press and hold down the Start Stop amp Reverse buttons then turn on the machine Press the Start Stop button to go to each mode then the Needle Up Down button to select the mode 1 8 Adjust feed balance adjustment Press the Needle Up Down button to test the 8 s After each mechanical adjustment pres
3. TEST amp SET MODES MODEL S MODE s Janome model s MB4 Elna models 940 9900 Screen Calibration 1 While holding down the Left Arrow button on the RCS turn on the machine Release when you see crosshairs on the screen 2 Touch the middle of each displayed crosshair until the screen displays OK If NG displays start over Upgrading With the ATA card already inserted in the RCS hold down the Left Arrow amp Trace buttons on the RCS then turn the machine on Keep holding the buttons down until you start to see vertical bars start to slide across the screen Do not touch the machine until the screen displays Finish Once it does turn the machine off and remove the card Test Mode While holding down the Start Stop amp Scissors buttons turn on the machine Release the buttons once you see icons on the screen Phase Press All Init to initialize the machine before doing anything else in the set mode Bottom dead pt Displays L at all times except when the hand wheel is at 0 where it will display H This all depends on where the upper shaft sensor shield plate is Needle Change Displays L at all times except when the hand wheel is at 270 where it will display H This all depends on where the upper shaft sensor shield plate is Needle Left amp Right arrow buttons to move the head to the specific needle Init to initialize NCHM Init Sen Moving Head Stop Position S
4. amp Lockstitch buttons Press the following key to enter the mode 1 Self Check See MEM below for instructions 2 Version The display the manufacturing version of the machine 3 Erase EEPROM Press MEM to reset the memory to factory default settings Press CLR to cancel and return to the test mode 4 Sensor Buttonhole amp upper shaft sensor check BH Buttonhole sensor Remove any foot you have on the machine When the buttonhole lever is all of the way down the LCD display will read L and H when the lever is touched or in the up position BS Upper shaft sensor check zigzag mode When the needle bar is up the LCD will display H and L when the needle bar is not in the highest position FS Upper shaft sensor check feed step mode When the needle bar is up the LCD will display L and H when the needle bar is not in the highest position 5 Switch bobbin winder The LCD will display SP OFF when the bobbin winder is to the left and SP ON when the bobbin winder is to the right 6 Blank 7 Blank 8 8 Adjust feed balance adjustment Press the Needle Up Down button to test the 8 s After each mechanical adjustment press the Start Stop button to initialize reset the feed step motor 9 0 MEM Step Check Self check Press CLR clear for each check Step1 LCD amp LED The LCD and LED will flash
5. thread drawing lever solenoid Bobbin Remaining bobbin thread check With the green bobbin gauge in first press Key until you get the most common number then press MEM1 Now insert the red bobbin gauge press Key until you get the most common number then press MEM2 Press OK to save it Bobbin Check Mode Remaining bobbin thread solenoid check Press Key to engage amp disengage Screen Calibration While holding the Start Stop button turn on the machine then let go when you enter the test mode Now press amp release the Start Stop Press TTP Adjust Press each of the 5 crosshairs left middle right top bottom Self Check While holding the Start Stop button turn on the machine then let go when you enter the test mode Step 1 Buzzer amp LED check Step 2 Start Stop amp Scissor button check Step 3 TB Sensor broken thread sensor check Step 4 Solenoid2 Spool bobbin winder Solenoid3 Trim End Solenoid4 Foot check Step 5 X Motor left right step motor Y Motor front back step motor PH Sensor upper shaft sensor DC Motor check Step 6 PC Card check Step 7 Design Card check Step 8 Design Card check Upgrading With the ATA card already inserted in the machine turn the machine on Press the Start Stop button when prompted Vertical bars will start to slide across the screen Do not touch the machine until the screen displays Finish Once it does turn the machine off and remove the card
6. LED buzzer and USB checks No 2 Button check S S Start Stop Rev Reverse AL Lockstitch U D Needle Up Down NT Needle Threader Trim Scissors Spool Bobbin Winder LCD U LCD Up LCD Down LCD Down No 3 TB Sensor Thread break check sensor Foot Sensor Foot up down micro switch YC Sensor Embroidery arm open close micro switch BH Sensor Buttonhole sensor P Foot Sen P foot sensor No 4 Tr Low bobbin thread solenoid Trim Thread cutter solenoid Spool Clutch release solenoid No 5 Be careful as the next step will cause the machine to run by itself Controller Foot controller Sliding Volume Speed control on front cover No 6 B SM Zigzag motor X SM X step motor on base TT SM Thread tension unit FD SM Feed dog step motor DC Motor DC motor SPL Motor Bobbin winder unit F SM Feed step motor Y SM Y step motor on base NT Motor Needle threader step motor LCD SM LCD Up down step motor PH Sensor Lower shaft sensor No 7 PC Card Check 1 No 8 If an ATA memory card were already inserted this would read OK USB Memory Check 1 No 9 f a USB stick were already inserted this would read OK NG Result Displays any micro switch sensor solenoid or step motor that did not work This will always show some steps as NG no good but it does not mean that part is not working When the checks were made the needle bar must be in a specific spot in order for certain micro switches sen
7. Lock Stitch and Needle Up Down buttons then turn the machine on Release when you see crosshairs on the screen Janome model s MC9500 MC350E MC300E Elna model s 8300 8200 Upgrading 1 With the machine off insert the ATA Card 2 With the ATA card already inserted turn on the machine Press and release the Start Stop button when prompted Janome model s MC350E MC300E Elna model s 820 8300 8200 Brightness Press to make the screen brighter or to make the screen darker Foot UD Presser foot up down micro switch H will display when the micro switch is activated or when the presser foot is up and L when the micro switch is deactivated or when the presser foot is down Sensor Off Press this key to sew with the broken thread sensor turned off Card USB Insert either a PC Card or USB Stick to check whether the A board can read these It may not read them if either the stick or card is not formatted correctly PH Sensor Turn the hand wheel to bring the needle up amp down Depending on where the shield plate goes thru the sensor will it display H or L Aging This will make the machine run by itself Press to decrease the time or to increase the time Solenoid Tension Solenoid thread tension release solenoid Thread Hold thread drawing lever solenoid Thread Cut thread cutter solenoid Solenoid Hold Tension Solenoid thread tension release solenoid amp Thread Hold
8. machine A new screen will show Press the button called Clear Turn off the machine Janome model s MC15000 Screen Calibration 1 While holding down the Left Arrow button on the RCS turn on the machine Release when you see crosshairs on the screen 2 Touch the middle of each displayed crosshair until the screen displays OK If NG displays start over Test Mode While holding down the Start Stop amp Reverse buttons turn on the machine Release the buttons once you see icons on the screen Foot Sensor Presser foot height adjustment Follow the Adjustments section of the PowerPoint service manual Foot Up Down Presser foot pressure adjustment Follow the Adjustments section of the PowerPoint service manual Foot Up Down Offset P foot height adjustment Follow the Adjustments section of the PowerPoint service manual Knee Lifter Knee lifter amp variable zigzag adjustment Follow the Adjustments section of the PowerPoint service manual Bobbin Remaining bobbin thread adjustment Follow the Adjustments section of the PowerPoint service manual Feed Dog Press the feed dog up amp down keys to raise or lower the feed dog to check the micro switch on the feed dog drop step motor When the feed dog is up the machine should display H and L when the feed dog is lowered Aging Once you press the Start Stop button the machine will run by itself for a certain amount of t
9. the machine to factory default C No Press C to cancel Step 4 Sensor The machine will read the propellers going thru the lower shaft sensor unit depending on which of the 3 blades are entering the sensor and the buttonhole sensor Csen Thread cut sensor left sensor Bsen Zigzag step motor sensor center sensor Fsen Feed step motor sensor right sensor BH Buttonhole sensor It should show L in the lowest position and H when pushed towards the front or back of the machine Step 5 Width Motor 1 OFF Press 1 to turn off the zigzag step motor 2 ORG 3 STUP Press 3 once to turn on or twice to calibrate it Step 6 Feed Motor 1 OFF Press 1 to turn off the feed step motor 2 ORG 3 STUP Press 3 once to turn on or twice to calibrate it Step 7 Tens Motor 1 OFF Press 1 to turn off the thread tension release step motor 2 ORG 3 STUP Press 3 once to turn on or twice to calibrate it Step 8 88888888 Feed balance adjustment Step 9 Switch SP Bobbin Winder FL Foot Up Down Micro switch Step 1 TD Foot Up Down Micro switch Step 2 DD Feed Dog Up Down Micro switch CL Thread Cutter Solenoid Micro switch Step 0 Solenoid Sol1 Thread Cutter Solenoid Sol2 Bobbin Holder Solenoid Sol3 Clutch Solenoid Step M Step Check Mirror Stitch Button Feed Max Elongation Button Width Max Bobbin Winding Button Sew Test Twin Needle Button Aging Press the Edit key to decrease the time amp keys t
10. ack into normal sewing mode with the thread check sensor turned off Phase Turn the hand wheel toward you slowly until the needle from its lowest position until Bight changes from L to H The needle height should be 7 2 to 8 2 mm above from the surface of the needle plate If not adjust the upper shaft shield position Other Sensor Trim Foot SW Thread cutter switch foot controller When plugged in and pressed the H will display When depressed or not plugged in the LCD will display L TB Thread check sensor When in the home position this should indicate L and H when manually pushed inwards Foot Foot controller check When not plugged in this should indicate 255 When plugged in and not pressed this should indicate around 5 and around 215 when completely pressed Slide Speed volume speed control on front cover This should read 255 when pushed to the left and around 1 when pushed to the right Straight With the straight stitch needle plate attached this should indicate H and ZigZag should indicate L ZigZag With the standard zigzag needle plate attached this should indicate H and Straight should indicate L Bright Press the or keys to make the screen brighter or darker Press OK to save the setting Clear Set Clears the memory completely This is for factory use only Needle Thread Needle threader adjustments Follow the Adjustme
11. ar is up bs zigzag step motor will display on the screen and when the needle bar is down the screen will display fs feed step motor Press the Start Stop button to initialize calibrate each step motor 12 DC motor check Run the machine using either the Start Stop button or the foot controller to test the DC motor _7 Machine resets _8 Machine resets _9 Bobbin winder check The LCD will display when the bobbin winder is to the left regular sewing mode and when the bobbin winder is to the right bobbin winding mode 10 The LCD will flash different characters Elna model s Diva 9000 Test mode While holding down the to left button amp top right button on the keypad turn on the machine Janome model s 888 Test mode While holding down the button on the lower part of the rear cover turn on the machine
12. e manual Bobbin Remaining bobbin thread adjustment Follow the Adjustments section of the PowerPoint service manual Feed Dog Press the feed dog up amp down keys to raise or lower the feed dog to check the micro switch on the feed dog drop step motor When the feed dog is up the machine should display H and L when the feed dog is lowered Aging Once you press the Start Stop button the machine will run by itself for a certain amount of time for testing purposes in either sewing or embroidery mode BH Sensor Buttonhole sensor amp Thread tension unit check Free The step motor will rotate and open the discs 3 4 The step motor will calibrate to the default setting Init The step motor will initialize BH Sensor BH Sen Remove any foot you have on the machine then lower the button lever When it is in the lowest position it should read L When you push on the lever or when the lever is all of the way up it should read H Cloth Guide With the cloth guide attached to the hoop press the button to initialize the position of the guide Press the lt or gt keys to move the cloth guide 15mm to the right from center needle position Press OK to save it 8 Adjust Feed decorative stitch balance Press the Start Stop button to sew eight 8 s Press Adjust to recalibrate the step motors after making an adjustment Sew Test Once you push the Start Stop button the machine will sew several
13. e you press the Start Stop button the machine will run by itself for a certain amount of time for testing purposes for both sewing and embroidery BH Sensor BH Sen Buttonhole sensor When the buttonhole lever is all of the way up this should read H With it all the way down this should read L TTM Sen Thread check sensor This should read L when in its home position With the shield plate out of the sensor it should read H Free Opens the tension discs 3 4 Sets the tension unit to default tension Init Calibrates the tension unit Cloth Guide With the cloth guide attached to the hoop press the button to initialize the position of the guide Press the lt or gt keys to move the cloth guide 15mm to the right from center needle position Press OK to save it 8 Adjust Feed Decorative stitch balance Sew Test Once you push the Start Stop button the machine will sew several stitches amp monogramming to test the machine Hoop Adjust Sensor Off The machine will turn restart itself back into normal sewing mode with all of the sensors turned off Phase Turn the hand wheel toward you slowly until the needle from its lowest position until Bight changes from L to H The needle height should be 7 2 to 8 2 mm above from the surface of the needle plate If not adjust the upper shaft shield position Other Sensor Spool Bobbin winder TB Thread check sensor Foot Foot controller Slide Speed Volume Speed control on f
14. ensor NCHM No Sen Needle Stop Position Sensor Brightness Press the and keys to make the screen brighter or darker X Y Motor Press Init to initialize Using the carriage gauge template change where the carriage home position is by pressing the jog buttons on the RCS unit Pick Up Press Init to initialize Cut Motor Press Init to initialize Sensor Solenoid Thread Tension Sensor Thread Break Sensor Thread keeper and Needle Bar Release Solenoid Thread Tension Sen When the tension discs are closed this will read L and when they are open it will read H Thread Break Sen When the tension disc wheels are not spinning the display will read L They will read H each time the slit rolls thru the sensor when you roll them by hand Solenoid1 Needle bar release solenoid Solenoid2 Thread keeper solenoid Spool Bobbin Winder Aging Press Start Stop to run the machine for the selected time amp speed Clear Set Clears the memory completely This is for factory use only Sensor Off Turns off the thread check sensor for testing purposes Once selected the machine will turn off then back on again with the thread check sensor turned off Cut Adjust Dynamic cutter adjustment To Find Out How Long the Machine was Run While holding down the Forward amp Bobbin Winder buttons turn on the machine To Reset Motor While holding down the Forward amp Bobbin Winder buttons turn on the
15. ime for testing purposes in either sewing or embroidery mode BH Sensor Buttonhole sensor amp Thread tension unit check Free The step motor will rotate and open the discs 3 4 The step motor will calibrate to the default setting Init The step motor will initialize BH Sensor BH Sen Remove any foot you have on the machine then lower the button lever When it is in the lowest position it should read L When you push on the lever or when the lever is all of the way up it should read H Cloth Guide With the cloth guide attached to the hoop press the Fy button to initialize the position of the guide Press the lt or gt keys to move the cloth guide 15mm to the right from center needle position Press OK to save it 8 Adjust Feed decorative stitch balance Press the Start Stop button to sew eight 8 s Press Adjust to recalibrate the step motors after making an adjustment Sew Test Once you push the Start Stop button the machine will sew several stitches amp monogramming to test the machine Hoop Adjust Embroidery unit home set position Press UP DOWN LEFT or RIGHT to move the carriage so it aligns with the hole of the template Press OK to save the adjustment MEM This will reset the carriage position to the previous saved setting DEF This will reset the carriage unit to factory specs X 1200 amp Y 1500 Sensor Off The machine will restart b
16. lding the Presser Ft Up Down amp Needle Up Down buttons turn on the machine Upgrading With the USB stick already inserted in the machine hold down the Needle Up Down amp Lockstitch buttons then turn the machine on Keep holding the buttons down until you start to see horizontal bars start to slide across the screen Do not touch the machine until the screen displays Finish Once it does turn the machine off and remove the stick Janome model s MC11000s MC11000 Elna model s 9600 9500 Upgrading With the ATA card already inserted in the RCS hold down the Needle Up Down amp Lockstitch buttons then turn the machine on Keep holding the buttons down until you start to see vertical bars start to slide across the screen Do not touch the machine until the screen displays Finish Once it does turn the machine off and remove the card Screen Calibration 1 While holding down the Needle Up Down button turn on the machine Release when you see crosshairs on the screen 2 Touch the middle of each displayed crosshair until the screen displays OK If NG displays start over To Find Out How Long the Machine was On amp Run With the machine off hold down the Needle Threader amp Scissors buttons then turn the machine on Test Mode While holding down the Start Stop amp Reverse buttons turn on the machine Release the buttons once you see icons on the screen 8 Adjust Press the Start Stop button to se
17. n amp Lockstitch buttons turn on the machine Release the buttons once you see icons on the screen Turn the jog dial to highlight the option and press the jog dial button to select it Press the reverse button to go back to the main menu for most steps 01 LCD Brightness Spin the jog dial to make the screen lighter or darker Press the jog dial button to save it 02 TTP Coordinate Using a stylus press the center of each indicated button and crosshair Press the jog dial button to save it 03 Self Check Enters the self check mode 04 Version Displays manufacturing version information 05 Initialize EEPROM 06 Sensor Bobbin Push the bobbin winder to the right and left to check the micro switch Foot Lift Assist Lift d Remote Cut d Needle Plate d BH Lever Pull the buttonhole lever down to test the sensor Feed Dog Flip the feed dog up down lever to drop and raise the feed dogs to check the micro switch 07 Phase Check 08 88888888 09 Solenoid 10 Width Max 11 Feed Max 12 Test Sewing 13 Aging 14 Step Check 15 Cutting Set Janome model s Mcs000 Elna model s CE20 Screen Calibration 1 Hold down the first 3 buttons on the front panel then turn the machine on 2 Release the buttons once you enter the screen calibration mode P Foot Sensor Adjustment 1 Janome model s MC8000 Elna model s 9006 Screen Calibration 1 With the machine off hold down the Reverse
18. nts section of the PowerPoint service manual Spool Bobbin winder adjustment Press the or keys to adjust the speed of the bobbin winder then press OK to save the setting O should be default Spool SW Not used SM Init Calibrates all of the step motors in the machine To Find Out How Long the Machine was Run While holding the Presser Ft Up Down amp Needle Up Down buttons turn on the machine Upgrading With the USB stick already inserted in the machine hold down the Needle Up Down amp Lockstitch buttons then turn the machine on Keep holding the buttons down until you start to see horizontal bars start to slide across the screen Do not touch the machine until the screen displays Finish Once it does turn the machine off and remove the stick Janome model s MC12000 Elna model s 900 Test Mode While holding down the Start Stop amp Reverse buttons turn on the machine Release the buttons once you see icons on the screen Foot Sensor Presser foot height adjustment Follow the Adjustments section of the PowerPoint service manual Foot Up Down Presser foot pressure adjustment Follow the Adjustments section of the PowerPoint service manual Foot Up Down Offset P foot height adjustment Follow the Adjustments section of the PowerPoint service manual Knee Lifter Knee lifter amp variable zigzag adjustment Follow the Adjustments section of the PowerPoint servic
19. o increase the time the machine will sew by itself Janome model s MC6600P MC6500P Mc49000C Elna model s 720 7300 7200 Test Mode 1 While holding down the Needle Up Down amp Lockstitch buttons turn on the machine 2 Press the 1 button within 3 seconds Reset Memory to Factory Default 1 While holding down the Needle Up Down amp Lockstitch buttons turn on the machine 2 Press 3 3 Press M Memory Janome model s 4120QDC Set Mode While holding down the Memory Key button turn on the machine Press mode for each step Use left right arrow keys to select the option and press Mem to save it 01 Buzzer On Off 02 Needle Position Up Down 03 Ttp Janome model s 3160QDC Test Mode While holding down the Needle Up Down amp Lock Stitch buttons turn on the machine Release the buttons then press the Start Stop button Press Reverse for each check 01 LCD Buzzer and LED Light check 02 Button check 03 Buttonhole Sensor check 04 Bobbin Winder Switch check 05 Presser Ft Lifter Switch check Press reverse to skip this step since there is no presser foot lifter switch on this model 06 Upper Shaft Sensor check 07 Zigzag amp Feed Motor check 08 Foot Controller check 09 Speed Control check 10 DC Motor check 11 Tension Unit Solenoid check 12 Thread Cutter Motor amp Button check Janome model s DC5100 Test Mode Press and hold down the Needle Up Down
20. ront cover Straight With the straight stitch needle plate attached this should indicate H and ZigZag should indicate L ZigZag With the standard zigzag needle plate attached this should indicate H and Straight should indicate L Bright Press the or keys to make the screen brighter or darker Clear Set Clears the memory completely Do not press YES on either selection This is for factory use only and can possibly blow the A board SM Init Calibrates all of the step motors in the machine Screen Calibration 1 While holding down the Needle Up Down button turn on the machine Release when you see crosshairs on the screen 2 Touch the middle of each displayed crosshair until the screen displays OK If NG displays start over To Find Out How Long the Machine was Run While holding down the Scissors amp Needle Up Down buttons turn on the machine Janome model s Mc9700 MC9500 Elna model s 8600 Screen Calibration 1 While holding down the Needle Up Down button turn on the machine Release when you see crosshairs on the screen 2 Touch the middle of each displayed crosshair until the screen displays OK If NG displays start over Test Mode While holding down the Start Stop button turn on the machine Release the buttons once you see icons on the screen Janome model s MC8900QCP Test Mode While holding down the Needle Up Dow
21. s the Start Stop button to initialize reset the feed step motor 2 Buttonhole sensor check Remove any foot you have on the machine When the buttonhole lever is all of the way down the LCD display will read L and H when the lever is touched or in the up position 3 Machine resets 4 Machine resets 5 Machine resets 6 Self check mode Press the Needle Up Down button for each check Step 1 LCD check 02 LED LCD check LD displays on the LCD and all of the buttons flash 03 displays on the LCD 04 displays on the LCD 05 Presser foot up down micro switch check When the presser foot is up the LCD displays UP and when dn when the presser foot is down 06 Buttonhole sensor check Remove any foot you have on the machine When the buttonhole lever is all of the way down the LCD display will read L and H when the lever is touched or in the up position 07 Upper shaft sensor check When the needle bar is in the up position the LCD will display H L When the needle bar is in the down position the LCD will display L L 08 Velocity upper shaft sensor check Numbers will display on the LCD and will change as you turn the hand wheel 09 Speed volume speed control check FE displays on the LCD and will then change to numbers as you slide the speed control to the left and right 10 F9 displays on the LCD 11 Zigzag amp feed step motor check When the needle b
22. sors and solenoids to correctly work Janome model s Mc10001 MC10000 Test Mode While holding down the Start Stop amp Reverse buttons turn on the machine Release the buttons once you see icons on the screen Screen Calibration 1 While holding down the Needle Up Down button turn on the machine Release when you see crosshairs on the screen 2 Touch the middle of each displayed crosshair until the screen displays OK If NG displays start over Upgrading With the ATA card already inserted in the RCS hold down the Needle Up Down amp Lockstitch buttons then turn the machine on Keep holding the buttons down until you start to see vertical bars start to slide across the screen Do not touch the machine until the screen displays Finish Once it does turn the machine off and remove the card Janome model s Mcg9900 Test Mode While holding down the Start Stop amp Reverse buttons turn on the machine Release the buttons once you see icons on the screen Bobbin Remaining bobbin thread adjustment Follow the Adjustments section of the PowerPoint service manual Elna model s 860 Foot Sen Feed Dog Foot U D Presser foot up down micro switch P Foot Presser foot P sensor Feed Dog Feed dog drop micro switch When the feed dogs are down this should read L Free Opens the tension discs 3 4 Sets the tension unit to default tension Init Calibrates the tension unit Aging Onc
23. ss the Start Stop button the machine will run by itself for a certain amount of time for testing purposes Brightness Press the and keys to make the screen brighter or darker Press X to save it Foot UD Zigzag foot micro switch H will display when the presser bar is up and L when the presser bar is down PH Sensor Lower shaft sensor check Turn the hand whee to test it Solenoid Press each icon to test the following solenoids Solenoid 1 Low bobbin check solenoid Solenoid 2 Thread cutter solenoid this will only work properly when the needle is in the lowest position Solenoid 3 Upper shaft clutch solenoid Spool Bobbin winder Hoop Adjust Adjust the X and Y position of the carriage Clear Set Clears the memory completely Do not press YES on either selection This is for factory use only and can possibly blow the A board Cloth Guide Press L to bring the carriage arm to the left and R to bring it to the home position Press and to adjust its position Press OK to save the adjustment Needle Threader L M and R changes needle position Press and to give the step motor more or less power to drive it thru the eye of the needle Press X to save the adjustment Self Check Mode While holding the Start Stop Reverse and Lockstitch buttons turn on the machine then let go when you enter the test mode No 1 Flash ROM LCD
24. stitches amp monogramming to test the machine Hoop Adjust Embroidery unit home set position Press UP DOWN LEFT or RIGHT to move the carriage so it aligns with the hole of the template Press OK to save the adjustment MEM This will reset the carriage position to the previous saved setting DEF This will reset the carriage unit to factory specs X 1200 amp Y 1500 Sensor Off The machine will restart back into normal sewing mode with the thread check sensor turned off Phase Turn the hand wheel toward you slowly until the needle from its lowest position until Bight changes from L to H The needle height should be 7 2 to 8 2 mm above from the surface of the needle plate If not adjust the upper shaft shield position Other Sensor Spool Bobbin winder TB Thread check sensor Foot Foot controller Slide Speed volume speed control on front cover Straight With the straight stitch needle plate attached this should indicate H and ZigZag should indicate L ZigZag With the standard zigzag needle plate attached this should indicate H and Straight should indicate L Bright Press the or keys to make the screen brighter or darker Press OK to save the setting Clear Set Clears the memory completely This is for factory use only SM Init Calibrates all of the step motors in the machine To Find Out How Long the Machine was Run While ho
25. w out 8x 8 s Adjust the feed balance mechanically then press Initialize to reset the feed system Press Start Stop to re test BH Sensor The display should read H when the lever is either up or when the slit is out of the sensor and L when the lever is all of the way down and not being touched Foot Sensor Feed Dog Foot P foot sensor With the P foot on the machine and the presser bar up the display should read L will change to H when the presser bar is down Feed Dog Feed dog drop step motor micro switches When the feed dogs are up the display should read H and L With the feed dogs down the display will change to L and H Bobbin Low bobbin check adjustment Use the green amp red bobbin gauges 00310KGAUGE to perform the adjustment 1 With the machine off hold down the Start Stop amp Reverse buttons then turn the machine on 2 Press Bobbin 3 Insert the red bobbin gauge Press Key until you get the most common number then press MEM1 4 Remove the green gauge and Insert the red gauge Press Key until you get the most common number then press MEMZ 5 Press X to save it and turn the machine off Sew Test Press the Start Stop button to let the machine sew several different stitches by itself to test the sewing Sensor Off The machine will turn restart itself back into normal sewing mode with all of the sensors turned off Aging Once you pre
Download Pdf Manuals
Related Search