Cafe Bar SCANOMAT PRO 6EU Coffee Machine
Contents
1. Note We recommend that the brewer be switched on permanently due to the ventilation system among others Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 10 Users service manual for Scanomat PRO6 EU Water connection When the water supply is being established please make sure that the coffee brewer is not situated on the rear end of the water supply system to ensure continuous supply of fresh water see illustration below 1 Connect the coffee brewer to the cold water line which is equipped with an adjustable check valve 1 2 external screw thread G F Before connecting the brewer draw off some buckets of water to clean the pipes If the water is not top quality we recommend that a Scanomat water filter is mounted Waterfilter optional 2 Fasten the hose nipple C which screws to the connecting nipple B available in angled and straight version 3 The connecting nipple 1s to be screwed on to the valve at the bottom of the coffee brewer 4 Dirt filter E and nipple D are to be mounted 5 The flange of the hose C is to be mounted on the nipples D and B 6 Turn on the water and make sure that all joints and connections are tight Note If the water has a disagreeable taste when heated we recommend that the heated water is drawn off the brewer and2. Reading Out Gata from the Machine did a ak aa a ajan aa pa naa a an a ana aa a a naen agi ng aa gga ena ban 21 IR CAI O ENC CUD e 21 CVG an Ing ANG GUD e EE 21 RACHA ING eer 22 Clearine tbe 0 070 EE 22 NGUSUD TG MAC EE 23 AdU SUN ND SIZE aaa a na aal aaa a ag aa a a e 23 Adjustine dink SEL CIV IN Sasa apada aaa ad ag ana a ad aaa aa aaa na Taha an ve a Kana a aa a agak ha I aaa aaa Da raa a aa an pan aa a naa aaa 24 NINA SUM D LAT DE saa seh naa ada a aaa a ad ah aa aan a La aaa aaa a a ag panik aa pa ka atone nd ai nah aal aha nai aaa naa a ai aa 24 A a a e a 23 Adu UII OS dr 29 AUS TA EE 26 PS NADIE ORs EE LO CRA o A nee ee renee ee eee ee eee ee nee er ere a aa a a ee 26 te EE O OOOO DO OE EE mm O aa a a aha naga aa aaa ah aa a aaa 27 AUS the EE 27 AS MS serigerin 28 Machine SE UU EE 29 MC E A 29 ee O e A A 29 EEN 29 PATINA EE 29 o EE 29 PUL OM Os 29 A Eegeregie 30 A EE 30 E E NAO 30 AMO SW a ess a aa D tinsel EE 30 O O hs Set N eni laga ana ec a 30 Be ITS ON AA NGE acta E ane eg Sat rine eat EE 30 Watertank E 30 KE E 30 BY Le E EE 31 Conneccion Chatt sasana AAA AAA AA EA A 33 Vibe All ie Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for Scanomat PRO6 EU Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for Scanomat PRO6 EU Technical specifications Power supply 230 VAC s
3. selecting between these 2 options is done by this function Weighing Weighing is a programme where drinks are dispensed without water and whipping The purpose is to verify the dispensed amount of products in the drinks Press the navigation button UP or DOWN until the display shows Pressing a selection button will now cause the machine to dispense the CHOCOLATE product included in this drink If the selected drink does not contain CHOCOLATE nothing will happen Use UP and DOWN to select between the different products in the machine To get an average take at least 5 portions before weighing it Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 30 Users service manual for Scanomat PRO6 EU Service key mode Service key mode is a mode which allows extra functions depending of the configuration of your machine There are a number of possible ways to enter this mode If your machine is equipped with the quality key system either based on magnetic cards or contact less TAGS a service mode key or TAG has been supplied with the machine If neither the Service key mode can be obtained by pressing a sequence of buttons on the keyboard There may be a maximum delay m between 2 presses of second The code is al follows DECAF SMALL CARAFE UP STRONG MILD DOWN LARGE MEDIUM CARAFE The machine will acknowledge by a sound The service key mode is left automatical
4. 1 N C 110 C 27 GREEN A S TT e N D stamen Sp gu 2 ONC e WHIPPER NA P2 S i 5 29 o BROWN BLUE ee O Pl 30 o BROWN RED E P3 nee O ER E n2 DAS 31 YELLOW 00 00 FUSE 9 10 232 33 o BLUE WHITE 34 o GREEN WHITE 35 o REDAWHITE oO WHITE RED WHITE BLUE y 36 YELLOW WHITE s STARTER ee a 1 a N C DOOR LIGHT BAL 2 NC 3 a N C DE TON AE HOT WATER d 4 YELLOW PINK OUTLET mo 5 o _GREY PINK DECAF gt 2 6 o __WHITE GREY TEA o 4 7 o C 8 a NC 9 2 NC WIRING DIAGRAM 10 BLACK id PRO 4 56 EU 22 11 2004 Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 33
5. valve will blink if not sufficient water in the water tank Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 17 Users service manual for Scanomat PRO6 EU Turning the machine on and off There are 2 ways of turning the machine off Either by pressing and holding the ON OFF button for 2 seconds or by switching the power off completely by activating the mechanical switch in the dispensing area Using the first option will keep the electronic board running with a very low power consumption less than watt As the internal watch in the machine is dependant on power always select this way to turn the machine off if you are using this When the machine is OFF the light in the display will be gone and only the Scanomat logo will be active Switching back on is done by pressing the ON OFF button or if this setting is active by pressing a selection button Dispensing a single standard drink Place a cup under the proper dispensing outlet and press the selection button If more than one outlet is available a graphic on the front of the machine will show which selections correspond with which outlets While brewing the display will show the name of the selected drink It 1s not possible to interrupt the dispensing of a single drink Preselections Apart from the direct selection buttons a number of preselection possibilities are available these will be explained in detail hereaf
6. 49 18 01 18 16 Users service manual for Scanomat PRO6 EU Operational procedures The keyboard Preselection keys DECAF D STRONG ap Vite Gola l ONOFF Navigation key o Ech GS E E Ed CD ES CD GD ur ur ir S selection keys BLACK COFFEE ESPRESSO Selection buttons The selection buttons will when the machine is operational meaning water in the tank and warm enough dispense the selected drink Place the cup at the appropriate position If more positions the right one will be indicated on the front of the machine Preselection buttons These buttons will activate a pre selection to the next drink The preselection buttons may differ from machine to machine and in some machines they may not all be active There is a time out of 15 seconds on all preselections Multiple preselections are allowed e g strong carafe Pressing NO or STOP will cancel all preselections Navigation button The navigation button is used to access the menu and programming system of your coffee machine When in adjust mode the UP and DOWN keys have an automatic repeat function This is activated be holding the key instead of just giving a single press In that case the adjustment will run instead of just step The Display The display will show relevant information in clear text and in symbols The thermometer will blink if the temperature in the water tank is too low for dispensing The water
7. 5 49 18 01 18 Users service manual for Scanomat PRO6 EU Machine settings The machine settings are a lot of different parameters which can be selected or deselected by you Press the navigation button UP or DOWN until following appears Press YES and the display will show Use UP and DOWN to scroll through all the different settings and press YES to change the setting currently in the display and following will appear example Press YES and the current status will appear in the lower line of the display Use UP or DOWN to alter this and YES to confirm Key beep Is simply the response sound when you press a button on the keyboard Child lock Is a function to prevent children from unintentionally activating your coffee machine If this function 1s active taking a selection is done by first pressing YES and while holding this pressed pressing the selection button Pressing the selection button alone in this mode will cause an alarm and the display will show Fahrenheit Is an option to have the temperature in the boiler displayed in Fahrenheit en stead of Celsius or centigrade Am Pm time Is selecting between the Am Pm way of showing the time and the 24 hour system Display watch Is choosing whether the watch should appear in the display whenever your coffee machine is in idle mode Automatic off If this setting is activated your coffee machine will automatically turn itself off 1
8. canomat PRO6 EU Adjusting the machine A lot of different parameters in the machine can be adjusted directly from the keyboard Press the navigation button UP until following appears Press navigation button YES and the first adjustable parameter will appear in the display Pressing UP and DOWN will scroll between the possibilities Adjusting cup sizes The cup size can be adjusted for each selection independently The pre programmed cup size is referred to as 100 and not as a fixed volume as the size may differ from selection to selection Enter the adjust menu as described above scroll to Press YES and the display shows Press a selection button and the display shows Press UP or DOWN to reach the desired level and press YES to confirm The machine will then return to and a new selection can be adjusted or the function can be abandoned by pressing NO Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 23 Users service manual for Scanomat PRO6 EU Adjusting drink strength The drink strength can be adjusted for each product for each selection independently The pre programmed strength is referred to as 100 and not as a fixed amount as it differs from selection to selection Enter the adjust menu as described above scroll to Press YES and the display shows Press a selection button and the display shows example This 1s pre program
9. display will show the current time with the minutes blinking Adjust these by pressing UP or DOWN and YES to confirm Adjust the hours in the same way Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 27 Users service manual for Scanomat PRO6 EU Adjusting the timers Your coffee machine is equipped with 4 programmable timers These are designed to power the machine down in certain periods The timers are all 24 hour based meaning that not weekly or monthly functions are available Enter the adjust menu as described and press UP or DOWN until the display shows Press YES and the display will show example 28 With the minutes blinking OFF indicating that this is the time where your coffee machine will power off Use the UP DOWN and YES to adjust this time and thereafter repeat he procedure with the ON time After that you will get the option to activate or deactivate the timer in question Example If you want your coffee machine to power down between 23 00 in the evening and 6 00 in the morning adjust the timerl to OFF 23 00 and ON 6 00 and set it to activated If you are using more than one active timer make sure that the timer periods are not overlapping You do not need to go through all timer adjustment to set just one When finished with one timer simply press NO to go back out Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 4
10. ed value and YES to confirm This way all 3 possible carafe sizes can be adjusted Adjusting the temperature This is the working temperature of the boiler in the machine and not the actual temperature of the dispensed drink This is lower due to mix with products and handling inside the machine The temperature of the tea water will be within 5 of this setting Enter the adjust menu as described and scroll to Press YES and the display will show Press UP or DOWN to reach the desired value and YES to confirm A max limit for this adjustment is pre programmed into the machine preventing you from setting the temperature too high Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 25 Users service manual for Scanomat PRO6 EU Adjusting the brew limit The brew limit is the lowest temperature of the boiler where the machine will allow dispensing of drinks If the temperature of the boiler is below this value the thermometer icon in the display will be blinking Enter the adjust menu as described and scroll to Press YES and the display will show Press UP or DOWN to reach the desired value and YES to confirm A min limit for this adjustment is pre programmed into the machine preventing you from setting the value too low Adjusting version Your coffee machine MAY be programmed with more than one set version of recipes If this is the case you can switch betw
11. een these different set by adjusting the active version Enter the adjust menu as described and scroll to Press YES and the display will show Press UP or DOWN to reach the desired value and YES to confirm If you adjust the version to a position in which no recipes are programmed into your machine the result will be the display showing When ever a selection key is pressed Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 26 Users service manual for Scanomat PRO6 EU Adjusting the language Your coffee machine may be programmed with different display languages To select the desired language first enter the adjust menu as described and press UP or DOWN until the display shows Press YES and the current language will be displayed Press UP or DOWN to reach the desired language and YES to confirm If the desired language is not programmed into your coffee machine the texts will be in English Adjusting the watch Your coffee machine 1s equipped with a watch The watch is running on the external AC counting the pulses from the power supply This means that if the mains is cut off the watch will stop So in order to keep the watch running and accurate the machine can only be switched off by means of the keyboard See section Turning the machine on and off Enter the adjust menu as described and press UP or DOWN until the display shows Press Yes and the
12. f has been inactive for 15 minutes Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 29 Users service manual for Scanomat PRO6 EU Cup light Your coffee machine may be equipped with a light illuminating the dispensed drinks If this is the case it can be activated or deactivated by means of this function Carafes If your machine does not have the direct carafe buttons on the keyboard the menu activated carafe function can be activated or deactivated by this function Mugs If your machine does not have the direct large button on the keyboard the menu activated large function can be activated or deactivated by this function Auto start If this function is active pressing a selection button when your machine is off will cause it to turn on heat up and dispense the selection when it is ready Sugar Your coffee machine may be equipped with a sugar preselection possibility If so the function can be activated or deactivated here Adjust lock If adjust lock is activated the menu system is locked out so only carafe large and read are available To enter the rest of the menu the machine must be in SERVICE KEY mode Note that setting this function to active is irreversible unless you have the option to go into SERVICE KEY mode Water tank Your coffee machine may be equipped with as well external water supply as an internal cold water reservoir If this is the case
13. ingle phase with ground connection or 400 VAC 2 3 phases with neutral and ground connection Idle power consumption approx 20 watt Dimensions Height 68 cm Width 35 cm Depth 39 cm Water tank Hot water tank capacity 5 litres Weight Gross 32 kg Nett 30 kg Water connection 2 6 Kp cm Environment Temperature 10 40 C Humidity max 90 RH Shelves transportation Temperature min 0 C 0000 CD C000 CIM MMO Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for Scanomat PRO6 EU Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for Scanomat PRO6 EU Installation The following installations must be provided Single phase connection 2 3 Phase Or 400 VAC 2 3 phase with o neutral and ground connection standby power consumption 20W 2 Water Inlet Pressure 2 6 bar IL Flow rate min 5l min Temperature 5 12 C 3 Table See diagram below Table layout Wall E SC g Sg Ip a 9605 a E e EEN i De ei 26 a Em EN LOZA 4 j My Hole for powercord 419 Feet mi Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manua
14. l for Scanomat PRO6 EU Service and repair is only to be carried out by service engineers educated by Scanomat The coffee brewer is to be secured additionally in accordance with regulations The coffee brewer must be earth connected yellow green conductor Note If the supply cable power cord has been damaged please note that only a maintenance engineer recommended by the manufacturer is to renew it as special tools are required Earth conductor yellow green Neutral conductor blue Phase brown black Note Place the coffee brewer on a stable table adjust the levelling feet until the brewer is level from front to back and side to side Be certain all four levelling feet are m contact with the table to prevent rocking of the brewer If there 1s a danger of the brewer falling down from the table it must be bolted down to the table top unscrew the levelling feet and fasten by screwing through the table top Note The coffee brewer requires ventilation Therefore there must be a minimum of 50 mm from the backside of the brewer to the wall The grating must be inspected frequently and vacuum cleaned If the installation site environment is especially dusty there must be vacuum cleaned each month Note Before connecting the coffee brewer draw off some buckets of water by means of the hose to clean the pipes and to avoid a disagreeable taste This procedure is also recommended when the brewer has not been operating for some time
15. let the brewer take in fresh water After long periods of inactivity holidays or weekends when the brewer has not been in operation for some time the water will loose its quality therefore we recommend activating the clean programme perhaps a couple of times in order to get fresh water into the tank In special cases it could be necessary to empty the water tank completely by means of the drain hose and then let the brewer take in fresh water This operation could be repeated if necessary It is important that the inlet water supply in a primary supply with its own stopcock this is to ensure that during daily operation there 1s a constant water pressure at the inlet Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 11 Users service manual for Scanomat PRO6 EU Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 12 Users service manual for Scanomat PRO6 EU Maintenance General Drawing A Ingredient canister B Ingredient funnel C Mixer bowl D Whipper house E Outlet hose F Outlet holder G Whipper tray H Drip tray I Main switch K Cover plate M Canister lid N Mixer lid O Whipper blade R Outlet tube T Mesh U Levelling legs Important To maintain the high drink quality and efficient operating conditions it is
16. ly after 30 seconds without any buttons being pressed Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 31 Users service manual for Scanomat PRO6 EU Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 32 Users service manual for Scanomat PRO6 EU Connection chart 1 PINK 2 S RED 3 o NC 16 4 BLUE SENSOR 5 PURPLE 6 4 GREY TEMP 7 x CODE WHITE 8 NC Ip 9 WHITE a Sve E it a FAN alee 10 gt BROWN BLACK ES gt O 11 WHITE BLACK Gg OVERHEAT SW 65 C DAA 12 4 GREY GREEN 13 5 BROWN 14 4 _GREY BROWM COFFEE gt 1 OUTLET 1 M 15 o BROWN WHITE ESP gt 3 16 YELLOW BROWN MILK gt 6 17 a PINKAWHITE CHOCO gt 5 1 2 18 o NC 19 a YELLOW GREY OUTLET 2 20 4 RED BLUE 21 o NC 22 PINK GREEN OUTLET 3 z O 16 S 23 ST mmarascow INLET E 4 P 24 NC cf 25 N C ed E l HEAT2800W a 110 C L 4 Q 26
17. med amount of COFFEE in the selected drink Press UP or DOWN to reach the desired value and YES to confirm If the selected drink has more than one adjustable ingredient the procedure will be repeated When no more adjustable ingredients in the current selection the display will return to Either select a new drink to adjust or press NO to go back Adjusting large 24 The large function is a way to make a selection a percentage bigger than the standard cup size for a selection This is calculated as adding a percentage to the pre programmed size Note that if the large function is not active in your machine this parameter will not appear in the adjust menu Enter the adjust menu as described and scroll to Press YES and the display shows Press UP or DOWN to reach the desired value and YES to confirm Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for Scanomat PRO6 EU Adjusting carafe The carafe function is a way to make number of cups of a selection Depending on the configuration of your machine it may have 1 2 or 3 different carafe sizes small medium and large Note that if the carafe function is not active in your machine this parameter will not appear in the adjust menu Enter the adjust menu as described and scroll to Press YES and the display will show S indicating the small carafe Press UP or DOWN to reach the desir
18. ne to be in SERVICE KEY mode Use the procedure above to read out the total cup counter When the total is in the display press CLEAN and the display will show Press YES to clear all the counters or NO to go back Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 21 Users service manual for Scanomat PRO6 EU Reading the product data If your machine is running with the quality key system either based on the magnetic keys or the contact less TAGS the amount of products in the memory can be read out Enter the read menu as described above scroll to Press YES and the display shows example Pe alternating with i a Pressing UP and DOWN allows you to scroll through the different products in your machine Press NO to go back Clearing the product data 22 Depending of the configuration of your machine 1t may be possible to clear the product data set them all to 0 This will cause the machine to be locked against dispensing until new quality keys has been inserted Clearing the product data also requires the machine to be in SERVICE KEY mode Use the procedure above to read out the product data When these total is in the display press CLEAN and the display will show Press YES to clear all the product data or NO to go back Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for S
19. o right and pull out nozzle and tube and whipper housing Click out mixer blade Place all parts ina Carry out same procedure and pull apart see warm soapy water and for all other mixer units next page for details Clean thoroughly Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 14 Users service manual for Scanomat PRO6 EU Whipper blade assembly The mixer blade pulls apart in 3 pieces When re assembling please note that all 3 parts must be properly aligned see drawing First assemble the silicon gasket and the actual blade Then push in the white teflon seal Finally mount the assembled whipper blade on the shaft pushing it in thoroughly until a click is heard Replace all parts in Make a final check on Wipe down inside Correct order the assembled parts in the machine The machine Turn ON the machine Press the CLEAN button Close the door place a Place a jug under the and the machine will do cup and test the machine dispense nozzles a rinse of all the ingredient by selecting a drink mixer units Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 15 Users service manual for Scanomat PRO6 EU Preventive maintenance The ingredient canisters are to be cleaned at regular intervals depending on the performance usage and environment the machine is installed in and furthermore the quality of the drinking water
20. of the utmost importance that all components that are in contact with the drinks are kept clean Important Machines dispensing beverages and shakes must be manufactured installed and operated in a way that leaves absolutely no risk of impairing or ruining the beverages and shakes All operations must follow the HACCP regulation Important Do not immerse the coffee machine into water and do not use high pressure cleaner Note A high degree of frequent daily maintenance secures a high level of trouble free operation of the coffee machine Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 13 Users service manual for Scanomat PRO6 EU Cleaning Caution Before starting the cleaning procedure make sure that the coffee brewer is switched off in order to avoid damages and injuries with hot water and moving parts Make sure to switch the machine off at the machine ON OFF switch see point I on the General Drawing Please note that only the low voltage control circuit will be cut off by this switch if the internal covers are removed there will still be mains voltage to the required circuits heaters etc H a a Wa as mn e kn Turn off Power to Open door amp flip Remove canisters Flip open mixer lids Machine open top lid and click them out y a H ae Lift up and remove Turn mixer housing Pull apart delivery Pull apart mixing bowl dispense nozzles t
21. re of the danger of scalding in the dispensing area when dispensing the various hot drinks Warning Before cleaning servicing etc that require the opening of the front door the switch situated in the delivery area must be switched off The brewer has been switched off when the display light turns off and the fan stops Note Please be aware that the switch only disconnects control circuit not the power supply Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for Scanomat PRO6 EU Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for Scanomat PRO6 EU a AAA A sues BO BNN NG Ag a a naa 7 Ire TE EE 9 EDAS EE 9 NE EE 11 A TAN A AA EU ANAA NG A A A a MA ANAA TANG A AA GA Kara A NGA A AG Mp AA E A A AAK 13 EE 14 Minas A a ap aa 15 EECHER sees 16 ETOUDIC SOO EE 16 ESCHER eege 17 A aver oh EE 17 DEE CU OM DUMAS da da b a aa a a A KA na b a ag ad 17 Presclecton DI ON EE 17 KEE ee EE 17 A na Na IA Ka Aa A a A Sang Baka aa Aa aa Ba DR aaa e Aa a Ba a daa a an ga ka aa Ka aana ada 17 IETS ENEE ee EE 18 IDISMENSING ID SETA We aa aaa aa is Nad aka anana aa pa aan ah SN aaa a aa a 18 EE 18 Dispens me GATI ES uti idilio 18 Dispense e E EE 19 Dias Ee 19 Dispense Strong Of Mild ARS cnt aiid Rare A AA KK AN ANAA A Ba anga ee Aa A aaa aaa 19 ACME agan aaa kaa a ag Laa a a aa D a nee BD Ga das 20
22. scanomat Users Service manual PRO6 EU H D MAI 2 Wi win Ei itor taiii Scanomeal CPs CAPA CO COIT nacian ee EH WR Lass CAFE LATTE TAE CRE TAPE OCA CAGE PATA Preliminary edition English edition Re ordering no 4300801 Version 1 00 Users service manual for Scanomat PRO6 EU Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for Scanomat PRO6 EU Congratulations on your choice of Scanomat Coffee Brewer Should you have any questions regarding the coffee brewer and the operation of it please do not hesitate to contact us We are convinced that you will be pleased with your choice Operation of the SCANOMAT Coffee Brewer The Scanomat coffee and coffee speciality brewers are high technology brewers which by means of a micro processor controlled brewing process dispenses various first class quality coffee drinks Water is heated in the thermostatically controlled hot water tank with automatic water inlet The water tank has built in safety switches and an overflow leading to the drip tray By means of an ingredient throw device the various instant products are led from the canisters to a brew chamber and here water 1s added If necessary the ingredients could be stirred mechanically in the brew chamber before the drink in question is led to the outlet spout It 1s possible to choose between cup and jug dispensing Important Warning Please be awa
23. should also be taken into consideration 1 Use hot water with a mild soap solution 2 Remove ingredient canisters 3 Empty canisters and remove remnants if any 4 Dismount the ingredient throw auger by pulling out the two snap locks thus it is possible to pull out the auger Rinse auger and ingredient canister in the hot water with mild soap solution Do not re install the ingredient canister and auger until they are completely dry 5 Re mount the ingredient canisters and fill up with ingredients for one day s consumption Please make sure that the canisters are completely dry before filling Trouble Shooting Problem Possible cause solution No operation at all Main switch 1 may be off Only water is dispensed No ingredient in the canisters Make sure all augers are tuning when operating A water tap symbol flashes in the display Check that water supply has been connected Activate CLEAN programme A thermometer flashes in the display Press the RESET button on the back of the machine Clogged mixing bowl or whipper Dismount and clean the mixing units See daily maintenance Dripping from outlet spouts Activate the clean programme a couple of times Dripping from the overflow at the Activate the clean programme a couple of times bottom of the machine Display shows OVERLOAD One of the whipper motors or auger motors are overloaded clogged Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45
24. spense all selection containing coffee or espresso in a decaf version Press the DECAF pre selction and the display will show Pressing a selection will now dispense the corresponding drink with all coffee or espresso products substituted with decaf coffee If the selection is a drink without any coffee or espresso in it e g a chocolate the preselection will not influence the drink Dispensing large cups When large is selected the machine will dispense a cup which is a certain percentage larger than the standard cup This means that a large cup is not necessary the same size for all selections Either press the direct LARGE button if such is available on the keypad otherwise use the navigation button to scroll up to LARGE The display will show Then press the desired selection Dispensing strong or mild drinks It is possible to adjust the strength for each individual drink by pressing STRONG or MILD prior to pressing the selection The strength can be adjusted in 10 steps The display will show Which product in the drink that is influenced by this preselection varies from selection to selection E g in a Cappuccino strong and mild will affect the coffee only Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 19 Users service manual for Scanomat PRO6 EU The menu 20 Using the navigation button the menu system for accessing all audit data adjustments and set
25. ter The preselctions can be used more than one at a time for example a carafe of strong decaf coffee is possible if the machine has all these 3 options available To cancel any preselection press STOP or NO All the preselections are controlled by a timer meaning that 1f no selections is made within 15 seconds after the preselection this will time out After the drink is dispensed all preselections are reset so if e g 2 strong coffees are wanted the strong needs to be pressed before each cup Dispensing carafes 18 Making a carafe of any product in this machine is always carried out as making a number of cups of the selection in question Place a carafe under the proper dispensing outlet If more than one outlet is available a graphic on the front of the machine will show which selections correspond with which outlets Either press a direct carafe button if such is available on the keypad otherwise use the navigation button to scroll up to a carafe The display will show While brewing the display will show the name of the selected drink and the number of cups left for this carafe Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for Scanomat PRO6 EU Pressing STOP or NO any time during a carafe brew will terminate the brewing after finishing the ongoing cup Dispensing decaf selections If the machine is equipped with DECAF coffee it is able to di
26. tings of the machine can be reached Pressing the arrow up and down YES to enter a function NO to go back one step does the navigation through the different menus Please note that not all menu points described in this manual is available in all machines as this can vary with different configurations The following sketch shows an overview of the complete menu system Vibe All 3 Postboks 131 2980 Kokkedal Phone 45 49 18 18 00 Telefax 45 49 18 01 18 Users service manual for Scanomat PRO6 EU Reading out data from the machine Some data can be read out your coffee machine directly from the keyboard Number of possibilities may vary from configuration of your machine Press the navigation button UP until following appears Press navigation button YES and the first adjustable parameter will appear in the display Pressing UP and DOWN will scroll between the possibilities Reading the cup counters Enter the read menu as described above scroll to Press YES and the display will show 3157 being the total number of cups dispensed including any cups which were parts of a carafe When the above display is shown the individual cup counters for each selection can be read by pressing the selection buttons accordingly Clearing the cup counters Depending of the configuration of your machine it may be possible to clear the cup counters set them all to 0 Clearing the counters also requires the machi
Download Pdf Manuals
Related Search