Finishing Brands Paint Cup - Operator Manual - 209V530
Contents
1. SERVICE MANUAL BINKS MODEL 80 295 2 QT STEADI GRIP PRESSURE CONTAINER CleanAir centrifugal air filter unit Air Nozzle not included Fluid Pressure Gauge Fluid Hose not included Safety Valve Do not tamper with or readjust Air Adjusting Valve not included SPECIFICATIONS Air Release Fluid Pressure Valve MAX CUP PRESSURE 50 psig 3 5 bar n i OVERALE HEIGHT 16 15 16 in 430 mm Lubricate Air Hose WITH AUXILIARY HANDLE f Cup Threads Hii OVERALL HEIGHT W O AUXILIARY HANDLE poi eee mm BASE DIAMETER 5 1 4 in 133 mm AIR INLET amp OUTLET CONNECTION Ha NRS M FLUID INLET amp OUTLET CONNECTION 3 8 NPS m FLUID CAPACITY 2 qts US 1 9 Itr WEIGHT 3 Ib 3 oz 1 46 kg OPERATION AND CLEANING IMPORTANT External Mix Air Nozzle Application The most efficient atomization air pressure is the lowest air pressure o tion that will properly atomize the paint This will minimize the overspray peration deposit more paint on the surface and eliminate paint waste 1 Connect hose as shown in diagram on front page 2 Fill cup with strained fluid mixed in accordance with If a faster coverage is necessary first increase fluid pressure and then manufacturer s recommendations on label of container adjust atomization air pressure If a slower coverage is more desirable first reduce the fluid pressure and then adjust atomization air pressure Alw2. ays attempt to maintain the lowest pressures for maximum efficiency 3 Fasten cover securely 4 Close air adjusting valve by turning clockwise 5 Set air pressure at CleanAir filter unit to between 35 and 80 PSI depending upon atomization desired For ease of removing cup cover and to prevent leakage always 6 Set regulator on pressure cup to approximately 10 PSI for thoroughly grease the threads on the cup enamels 5 PSI for lacquers Turn knob clockwise to increase pressure to reduce pressure turn knob counter clockwise Always T release air in cup by momentarily opening air release valve on CAUTION cover when attempting to reduce pressure 7 Open air adjusting valve If the cup is accidentally tipped over or held at too great an 8 With trigger fully pulled back make several fast spray strokes angle fluid will load up the underside of cup cover and leak against a flat surface After adjustment of pressure proper into regulator In the event this happens clean immediately atomization will be indicated by an even distribution of finely divided paint particles continued on page 3 77 2823 R7 1 11 2014 1 4 BINK In this part sheet the words WARNING CAUTION and NOTE are used to emphasize important safety information as follows A WARNING Hazards or unsafe practices which Hazards or unsafe practices which could result in minor personal injury product or property damage could result in severe perso
3. cover and clean cup and cover thoroughly Operation 6 With approximately 1 4 to 1 2 cup of clean solvent attach cover and set fluid pressure at approximately 10 PSI 7 Close air adjusting valve at spray gun 8 Trigger gun and allow solvent to flow into a container until it flows clear 9 Remove solvent then clean air nozzle If any dirt appears in 7 ae Sa orifice clean with tooth pick Blow nozzle and cup dry Replace The internal mix air nozzle accomplishes atomization by mixing the air nozzle and cover loosely and fluid within the air nozzle 1 Close air adjusting valve by turning clockwise A CAUTION 2 Set air pressure at CleanAir filter unit to approximately 45 PSI 3 Open air adjusting valve and allow air to enter the gun 4 Set fluid pressure at 20 Ibs and adjust higher or lower until desired atomization is effected Air pressure should be alternately adjusted The steps are the same as with the external mix nozzles except the air and fluid pressure settings are different Never use a wire or metal object to clean the air nozzle they may damage the nozzle and cause faulty spray Cleaning 1 Open air release valve on pressure cup cover 2 Reduce pressure in cup until gauge reads zero turn knob counter clockwise Never allow solvent to remain in cup solvent vapors tend to f reduce service life of gasket Separate storage of cup and 3 Loosen cup cover and set fluid tube on angle in cu
4. ds eu Tel 44 0 1202 571 111 Fax 44 0 1202 573 488 China www finishingbrands com cn mkt finishingbrands com cn Tel 8621 3373 0108 Fax 8621 3373 0308 Mexico www finishingbrands com mx sales finishingbrands com mx Tel 011 52 55 5321 2300 Fax 011 52 55 5310 4790 France www finishingbrands eu info finishingbrands eu Tel 33 0 475 75 27 00 Fax 33 0 475 75 27 59 Japan www ransburg co jp binks devilbiss ransburg co jp Tel 081 45 785 6421 Fax 081 45 785 6517 BINnKS Binks is part of Finishing Brands a global leader in innovative spray finishing technologies For technical assistance or to locate an authorized distributor contact one of our international sales and customer support locations below Brazil www devilbiss com br sales devilbiss com br Tel 55 11 5641 2776 Fax 55 11 5641 1256 Germany www finishingbrands eu info finishingbrands eu Tel 49 0 6074 403 1 Fax 49 0 6074 403 281 Australia www finishingbrands com au sales finishingbrands com au Tel 61 0 2 8525 7555 Fax 61 0 2 8525 7500 awe 77 2823 R7 1 11 2014
5. nal injury death or substantial property damage A WARNING Read the following warnings before using this equipment READ THE MANUAL Before operating finishing equipment read and understand all safety operation and maintenance information provided in the operation manual Important installation operation or maintenance information PROJECTILE HAZARD You may be injured by venting liquids or gases that are released under pressure or flying debris OPERATOR TRAINING PINCH POINT HAZARD All personnel must be trained before operating finishing Moving parts can crush and cut Pinch points are basically any equipment areas where there are moving parts EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture malfunction or start unexpectedly and result in serious injury STATIC CHARGE Fluid may develop a static charge that must be dissipated through proper grounding of the equipment objects to be sprayed and all other electrically conductive objects in the dispensing area Improper grounding or sparks can cause a hazardous condition and result in LOCK OUT TAG OUT fire explosion or electric shock and other serious injury I Failure to de energize disconnect lock out and tag out all power sources before performing equipment maintenance could cause serious injury or death WEAR RESPIRATOR Toxic fumes can cause serious injury or death if inhaled Wear a respirator as recomme
6. nded by the fluid and solvent AUTOMATIC EQUIPMENT manufacturer s Material Safety Data Sheet Automatic equipment may start suddenly without warning TOXIC FLUID amp FUMES Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin inhaled injected or swallowed LEARN and KNOW the specific hazards or the fluids you are using FIRE AND EXPLOSION HAZARD Improper equipment grounding poor ventilation open flame or sparks can cause a hazardous condition and result in fire or explosion and serious injury PRESSURE RELIEF PROCEDURE Always follow the pressure relief procedure in the equipment instruction manual KEEP EQUIPMENT GUARDS IN PLACE Do not operate the equipment if the safety devices have been removed MEDICAL ALERT Any injury caused by high pressure liquid can be serious If you are injured or even suspect an injury e Go to an emergency room immediately e Tell the doctor you suspect an injection injury e Show the doctor this medical information or the medical alert card provided with your airless spray equipment e Tell the doctor what kind of fluid you were spraying or dispensing KNOW WHERE AND HOW TO SHUT OFF THE EQUIPMENT IN CASE OF AN EMERGENCY WEAR SAFETY GLASSES Failure to wear safety glasses with side shields could result in serious eye injury or blindness GET IMMEDIATE MEDICAL ATTENTION To prevent contact with the fluid please note the following e Neve
7. p cover recommended 80 295 PARTS LIST Ind ae a ent Description Parts Req d 1 80 4 CUP 2 QUART 1 2 80 34 TUBE MATERIAL 1 3 80 11 GASKET TRI SEAL FOAM 1 4 80 297 COVER 1 5 80 12 AIR RELEASE VALVE 1 6 72 1022 A CENTERPOST ASSEMBLY 1 7 80 33 OUTLET 1 8 20 353 JAM NUT 5 16 18 1 9 83 1899 HANDLE 1 AIR REGULATOR ASSEMBLY 10 85 440 MAX 50 PSI FLUID PRESSURE 1 See part sheet 2817 11 80 267 VALVE 1 12 60 7 SPRING 1 2ND REGULATOR KIT 13 85 441 MAX 60 PSI for atomizing air control order separately Available in quantity pack For Tri Seal Gaskets order 80 11 5 qty of 5 A Available from Binks distributors only 77 2823 R7 1 11 2014 3 4 BINK WARRANTY POLICY Binks products are covered by Finishing Brands one year materials and workmanship limited warranty The use of any parts or accessories from a source other than Finishing Brands will void all warranties For specific warranty information please contact the closest Finishing Brands location listed below Finishing Brands reserves the right to modify equipment specifications without prior notice DeVilbiss Ransburg BGK and Binks are registered trademarks of Finishing Brands 2014 Finishing Brands All rights reserved BINnKS USA Canada www binks com info finishingbrands com Tel 1 800 992 4657 Fax 1 888 246 5732 United Kingdom www finishingbrands eu info finishingbran
8. r point the gun valve at anyone or any part of the body e Never put hand or fingers over the spray tip INSPECT THE EQUIPMENT DAILY Inspect the equipment for worn or broken parts on a daily basis Do not operate the equipment if you are uncertain about its eho se condition e Never attempt to stop or deflect fluid leaks with your hand NEVER MODIFY THE EQUIPMENT body glove ar Fea Do not modify the equipment unless the manufacturer provides e Always have the tip guard on the spray gun before spraying written approval e Always ensure that the gun trigger safety operates before spraying NOISE HAZARD PROP 65 WARNING You may be injured by loud noise Hearing protection may be CA PROP WARNING This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm required when using this equipment i Ul IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT FOR FURTHER SAFETY INFORMATION REGARDING THIS EQUIPMENT SEE THE GENERAL EQUIPMENT SAFETY BOOKLET 77 5300 Binks reserves the right to modify equipment specification without prior notice Binks 2 4 77 2823 R7 1 11 2014 BINKS MODEL 80 295 2 QT STEADI GRIP PRESSURE CONTAINER OPERATION AND CLEANING 4 Loosen air nozzle two turns place cloth over nozzle and pull the Internal Mix Air Nozzle Application trigger Be fOrcE Pain ints cup 5 Remove
Download Pdf Manuals
Related Search