- Tillotson
Contents
1. SUPPLY FUEL FUEL UNDER PRESSURE FUEL UNDER VACUUM ATMOSPHERIC AIR PUMP IMPULSE AIR HIGH SPEED MIXTURE SCREW ORIFICE SECONDARY VENTURI HIGH SPEED MIXTURE SCREW ORIFICE f PRIMARY VENIURI THROTTLE SHUTTER SECONDARY IDLE FUEL DISCHARGE PORT DIAPHRAGM GASKET FUEL PUMP DIAPHRAGM INCLUDING INLET amp OUTLET FLAPPER VALVES FUEL STRAINER GASKET Fuel Pump Operation The fuel pump is a pulse operated diaphragm type where the inlet and outlet check valves are flap valves The pumping pulse is supplied from the changes in engine base pressure caused by the motion of the piston PRIMARY VENTURI THROTTLE SHUTTER METERING SERVICE DATA HOW TO DISASSEMBLE FOR CLEANING AND REPAIR The model HR carburetor should be cleaned and inspected at regular intervals depending on the service conditions Select a clean work area because dirt ad carelessness are the causes of most carburetor trouble CAUTION Some solvents and cleaners have a damaging effect on the synthetic rubber parts used in carburetors It is best to use a petroleum product for cleaning Do not use alcohol acetone lacquer thinner benzol or any solvent with a blend of these ingredients unless the rubber parts and gaskets are removed If you are in any doubt about your solvent test a used part in it and observe the reaction The entire carburetor should be cleaned by flushing with fuel and blown dry with c2. A carefully rebuilt HR model carburetor should perform well The two most likely causes of carburetor failure are dirty and a careless repair job Aclean carefully assembled unit should be nearly as good as new u x OCE the following page for operational trouble and remedy data TROUBLE CARBURETOR FLOODS ENGINE WILL NOT ACCELERATE ENGINE WILL NOT IDLE ENGINE RUNS OUT LEAN CARBURETOR RUNS RICH WITH HIGH SPEED MIXTURE SCREW SHUT OFF NOTE Turn mixture screw carefully a i aie a TROUBLE DATA POSSIBLE CAUSE Dirt or foreign particles preventing inlet gt needle from seating Stuck inlet Lever gt gt Faulty choke stop allowing choke to close Spring not seated on lever dimple Diaphragm Improperly installed Plugged air filter Fuel tank pressure build up Inlet Lever adjusted too high PP gt Diaphragm cover plate loose O5 O No fuel al Idle mixture too lean Low inlet lever setting Carburetor loose on manifold Diaphragm gasket leaking Fuel channels plugged TF nD l Inlet lever set incorrectly Sticking inlet needle or lever s Incorrect adjustment Fuel channels plugged Pump pulse hole not aligned with flange hole Throttle shutter cocked in the throttle bore causing fast idle Faulty nozzle check cage Welch plug does not
3. fof omnm TILLOTSON LTD CLASH INDUSTRIAL ESTATE TRALEE CO KERRY IRELAND PHONE 353 66 7121911 FAX 353 66 7124503 e mail sales tillotson ie SERVICE MANUAL INTRODUCTION Tillotson has developed the HR Series Diaphragm carburetor for engines with a displacement of from 12 to 25 cubic inches per cylinder It is available as a complete fuel system including carburetor integral fuel pump and filter for two stroke cycle engines or as a carburetor and integral fuel filter for four stroke cycle engines The diaphragm controlled metering system allows precise fuel metering to the engine at extreme tilt angles and prevents fuel level changes due to vibration The dual venturi used in this model series multiples the venturi pressure drop causing fine atomisation of the fuel that is delivered from the main fuel nozzle so that the fuel reaches the engine as a combustible fog instead of a fluid stream The main benefit of this venturi system is increase power and fuel economy Designed with a minimum number of parts this compact unit has retained the dependability and easy servicing features of the smaller Tillotson diaphragm carburetor that have been in use throughout the world for several years Information contained in the following pages is presented as an aid to understanding the construction operation and servicing of the HR series carburetor SERVICE MANUAL CARBURETOR ADJUSTMENT The high speed and idle mixture scr
4. APHRAGM INLET VALVE PUMP DIAPHRAGM OUTLET VALVE FUEL PUMP COVER FUEL INLET STRAINER COVER FUEL PUMP CHAMBER STRAINER COVER RETAINING SCREW FUEL STRAINER SCREEN STRAINER COVER GASKET PULSE CHAMBER ATMOSPHERIC CHAMBER METERING DIAPHRAGM DIAPHRAGM COVER ATMOSPHERIC VENT FULCRUM PIN INLET CONTROL LEVER HIGH SPEED MIXTURE SCREW INLET TENSION SPRING INLET NEEDLE amp SEAT INLET SEAT GASKET FUEL INLET SUPPLY CHANNEL SEE FOLLOWING PAGES FOR OPERATIONAL DATA OPTIONAL CONFIGURATIONS FUEL INEET mu IDLE SPEED SCREW for the HR Model Carburetor The Model HR carburetor is HIGH SPEED __ also available with a plain FUEL MIXTURE diaphragm cover plate The SCREW fuel must come from a separate fuel pump or an overhead fuel tank for a MAIN FUEL DISCHARGE PORT FUEL INLET SUPPLY CHANNEL INLET NEEDLE FUEL STRAINER SCREEN IDLE MIXTURE SCREW ORIFICE SECONDARY IDLE DISCHARGE PORT THROTTLE SHUTTER i PRIMARY IDLE FUEL DISCHARGE PORT IDLE FUEL SUPPLY CHANNEL IDLE FUEL MIXTURE SCREW eee DIAPHRAGM gravity fuel supply for these GASKET two optional models FUEL INLET CONTROL LEVER METERING DIAPHRAGM ATMOSPHERIC VENT METERING DIAPHRAGM COVER IDLE SPEED SCREW SECONDARY IDLE HH DISCHARGE PORT MAIN FUEL e cycle forces the DISCHARGE PORT THROTTLE SHUTTER 2 fuel pump PRIMARY IDLE FUEL FUEL INLET _ DISCHARGE PORT SUPPLY CHAN
5. DLE FUEL SUPPLY CHANNEL METERING CHAMBER DIAPHRAGM GASKET METERING DIAPHRAGM Jipin iR OPERATIONAL DATA SECONDARY VENI URI Intermediate Operation Fuel is delivered into and MAIN FUEL through the carburettor in the DISCHARGE PORT Same manner as when the engine is idling However as the throttle opens and engine speed increases more fuel is demanded from the carburettor and supplied to the engine by the secondary idle discharge port located immediately behind the throttle shutter As the throttle shutter continues to open and engine speed increases the velocity of air through the venturi creates a low pressure area at the venturi throat and diminishes the suction on engine side of the throttle shutter When the pressure at the venturi throat is less than that existing within metering diaphragm fuel chamber fuel is drawn up through high speed mixture screw orifice and out main fuel discharge port High Speed Operation As the throttle shutter progressively opens from intermediate position to full open position the air velocty through the venturi increases and fuel is metered up through high speed mixture screw orifice and main fuel discharge port in accordance with the power requirements of the engine The action of the metering diaphragm is the same as previously described with suction required to operate the diaphragm being transmitted through the main fuel discharge port MAIN FUEL DISCHARGE PORT _
6. NEL IDLE FUEL SUPPLY CHANNEL INLETSEAT __ METERING CHAMBER INLET NEEDLE _ pon ENET NE SASS RUM PULSE CHAMBER supy FUEL CONTROL TE ER al n ZZ Z FUEL PUMP CHAMBER OUTLET SURGE _ CLAY SY INLET SURGE CHAMBER Bae ee oe CHAMBER p ZA ai INLET VALVE DIAPHRAGM INLET CHECK VALVE lt y rA eee TMOSPHERIC AIR FUEL STRAINER SCREEN we FUEL INLET FUEL PUMP OPERATION The fuel pump is a pulse operated diaphragm pump The pressure vacuum pulse is supplied from the engine crank case where the pulse cycles are created by the reciprocating action of the engine piston Crankcase pulse is transmitted to the pump pulse chamber through the fuel pump pulse port in the mounting flange of the carburetor body The vacuum part of the pulse cycle causes the fuel pump diaphragm to move into the pump pulse chamber creating a vacuum in the fuel pump chamber that allows fuel to flow from the fuel inlet through the fuel Strainer screen past the inlet check valve and into the fuel pump chamber The vacuum in the fuel pump chamber closes the outlet check valve during this part of the pumping cycle The pressure part of the pulse cycle forces the fuel pump diaphragm into the fuel pump chamber creating a pressure on the fuel that forces it out of the fuel pump chamber through the outlet check valve and through the fuel inlet supply channel to the inlet needle valve The fuel pressure closes the inlet check valve during thi
7. be cleaned by blowing the parts with compressed air and carefully blowing out each channel and orifice in the castings REPLACE ALL WORN PARTS Assemble the carburetor Make certain that all parts are kept clean before they are assembled to the body casting Few measurements are required to complete the assembly of this simple unit 1 Tighten the inlet seat to 25 30 inch pounds of torque 2 Adjust the inlet control lever so that the center of the lever that contacts the metering diaphragm is flush to the metering chamber wall as shown in the drawings 3 Install new welch plugs at the nozzle well and bypass chamber if the original parts were damaged or removed Place the new welch plug into the casting counter bore convex side up and flatten it to a tight fit using a 5 16 inch flat end punch If the installed welch plug is flat 4 Assemble the gaskets diaphragms and castings in the correct order 5 Assemble the throttle shaft into the carburetor body and attach the throttle shaft clip before assembling the throttle shutter With the shaft secured in place assemble the shutter into the shaft Make certain tha the shutter fits accurately into the throttle bore in the closed position 6 Assemble the spring and ball into the choke shaft hole and assemble the shaft into position Assemble the shutter into the choke shaft Make certain that the choke shutter fits tightly to the carburetor bore in the closed position
8. et is assembled onto the body casting first and the metering diaphragm is assembled next to the gasket s Remove the fulcrum pin retaining screw the fulcrum pin inlet control lever and the inlet tension spring Use caution in removing these parts because the spring pressure may cause the inlet lever to fly out of the casting Inspect the parts for wear or damage The inlet control lever must rotate freely on the fulcrum pin e Handle the inlet spring carefully Do not stretch this spring or in any way change its compression characteristics If in doubt about its condition replace it Remove the inlet needle Remove the inlet seat assembly using a 5 16inch thin wall socket wrench Remove the inlet seat gasket The inlet seat assembly consists of a brass cage and a rubber insert for the inlet needle seat The insert goes into the cage only one correct way Looking at the insert one side is flat and smooth the other side has a ridge or rim moulded around the outside edge This ridge is to be assembled away from the inlet needle point Some models of the HR carburetor are equipped with a rubber tipped needle a brass inlet seat and a copper gasket The installation instructions below are applicable to both types of inlet seats The inlet needles and seats are matched and tested for leaks at the factory and the parts should not be interchanged they must be kept in matched sets When installing the insert cage into the carbu
9. ews have normal right hand screws thread These adjustments are turned closed wise to close or lean the mixture and counter clockwise to open or enrich the mixture The starting adjustment opening for a new unit or a carburetor that has not been run on the engine is one full turn open on both the high speed and idle mixture screws The idle speed screw should be adjusted to open the throttle shutter a small amount This adjustment should be carefully made on vehicles that have a centrifugal clutch drive arrangement a very high idle speed may cause the clutch to engage and the vehicle may start to move Open the fuel line shut off valve if your engine is equipped with one and close the choke shutter Open the throttle about one quarter of full travel and firmly pull the starting cord until the engine fires Open the choke shutter far enough to allow the engine to idle until it has warmed up enough to run continuously with the choke fully open Do not race a cold engine Adjust the idle mixture screw to obtain a smooth steady idle and re adjust the idle speed screw to obtain the idle speed recommended by the engine manufacturers Re check the idle mixture adjustment at the recommended idle speed An over rich idle mixture will cause the engine to fire unevenly and there will be smoke from the exhaust A lean idle mixture will usually cause back firing The high speed mixture screw should be adjusted with the engine at fully open thro
10. ompressed air before disassembly The carburetor should be inspected for cracks in the casting bent or broken shafts loose levers or swivels and stripped threads O Inspect the idle speed screw washer and tension spring Inspect the casting for thread damage In the event the casting is ripped of threads repair by inserting an 8 32 Heli coil 3 16 long The fuel inlet and filter cover are removed by removing the center screw Remove the filter cover the cover gasket and filter screen The filter screen should be cleaned by flushing with fuel or solvent and blowing with compressed air It is advisable to replace the gasket whenever the filter screen is serviced Flush all dirt from the plastic cover before assembly Remove the six body screws and the fuel pump cover casting Remove the fuel pump diaphragm and gasket Inspect pump diaphragm it must be flat and free from holes The gasket should be replaced if there are holes or creases on its sealing surface Be certain to re assemble these parts in the correct order The pump gasket the fuel pump diaphragm should be assembled next to the gasket and the flap valve member next to the fuel pump diaphragm so that the flap valves will seat against the fuel pump cover 4 Remove the diaphragm cover casting the metering diaphragm and diaphragm gasket Inspect the diaphragm for holes tears and imperfections These parts must be re assembled in the correct order The diaphragm gask
11. retor body use a new gasket Do not force the cage as you may strip the threads or distort the insert Use a torque wrench to apply 25 to 30 inch pounds pressure The needle and seat assembly must be clean to insure correct performance Remove and inspect the points of both the high speed and idle mixture screw Notice the idle mixture screw point has the step designed to minimise point METERING CHAMBER FLOOR INLET CONTROL LEVER SET FLUSH WITH CHAMBER FLOOR ay Pe HIGH SPEED MIXTURE SCREW IDLE MIXTURE SCREW LOW DEPRESS HERE THEN PUSH TABS DOWN PRY UP HERE Be bent extruded from being forced into the casting seat or possibly broken off in the casting If either mixture screw is damaged be sure to inspect the condition of the casting If the adjustment seats are damaged a new body casting is required The idle bypass ports and main nozzle ball check valve are sealed from the metering chamber by welch plugs It is seldom necessary to remove either of these plugs because there is no wear in either section and any dirt that may accumulate can usually be blown out with compressed air through the mixture screw holes If the carburetor is unusually dirty and the welch plugs must be removed it will require careful work If the drill travels too deep into the cavity the casting may be ruined Pry the welch plug out of its seat using a small punch Inspect the idle bypass holes to insure they are no
12. s part of the pumping cycle The inlet and outlet surge chambers diminish the pressure surges of the fuel and provide steady fuel flow through the pump system CARBURETOR SECONDARY VENTURL PRIMARY VENTURI MAIN FUEL CHECK VALVE POWER VALVE Fi THROTTLE SHUTTER CHOKE SHUTTER SECONDARY IDLE FUEL g DISCHARGE PORT MAIN FUEE SUPPLY CHANNEL PRIMARY IDLE FUEL DISCHARGE PORT a IMPULSE PORT TO PUMP IDLE FUEL SUPPLY CHANNEL INLET NEEDLE ATMOSPHERIC VEN DIAPHRAGM CHAMBER INLET CONTROL LEVER METERING DIAPHRAGM INLET TENSION SPRING DIAPHRAGM BUTTON STARTING choke OPERATION Starting an engine with the HR carburetor involves the same methods that are used in a conventional float type carburetor As the engine is cranked with the choke in the closed position engine suction will be transmitted to the diaphragm fuel chamber through both primary and secondary idle discharge ports as well as the main fuel discharge port creating a low pressure area on IDLING OPERATION The throttle shutter is a partially open position when the engine is idling Engine suction is transmitted through the primary idle fuel discharge port to the fuel chamber side of metering diaphragm via the idle fuel supply channel Again the metering diaphragm is forced upward by atmospheric pressure depressing the inlet control lever and permitting fuel under pressure to force the inlet needle off its seat and enter
13. seal Diaphragm vent plugged Tank vent not operating Fuel line plugged gt Leak in fuel system from tank to pump p Pump pulse hole plugged or not aligned with engine pulse hole Pump valve flippers damaged or bent off ports Dirty inlet screen O I n Clogged fuel chanels Incorrect inlet leer adjustment Low fuel supply Welch plugs not sealing Ruptured pump diaphragm Carburetor flooding 9 REMEDY Clean or replace the inlet needle and seat Replace or clean Correct the assembly Correct or replace Clean Filter Replace choke shaft assembly Check tank vent Adjust flush with chamber floor Readjust Adjust Flush with chamber floor Tighten Tighten cover plate screws Replace gasket Clean carburetor Fill fuel tank Readjust Clean carburetor Set flush with chamber floor Replace or clean Align Adjust shutter position Replace nozzle assembly Replace welch plug Clean Repair Clean fuel line Replace line Clean or correct alignment Replace pump diaphragm Clean filters Clean carburetor Set lever flush with chamber floor Fill fuel tank Replace welch plugs Replace pump diaphragm See above DO NOT FORCE MIXTURE SCREWS INTO SEATS
14. t plugged Do not push drills or wires into the metering holes This may alter carburetor performance Blow plugged holes clean with compressed air Remove the main nozzle ball check assembly with a screwdriver of correct blade width If this ball check is defective the engine will not idle unless the high speed mixture screw is shut off or there will be poor high speed performance with the high speed mixture screw adjusted at 1 1 4 turns open Replace the defective part The choke and throttle shafts may be removed if there is evidence of wear on these parts The shafts do not have to be removed before cleaning the body casting if the parts are not worn Mark the throttle and choke shutters before removing them so that they can be re assembled correctly The edges are tapered for exact fit into the carburetor bores Remove two screws and pull the shutter out of the carburetor body Remove the throttle shaft clip and pull the shaft out of the casting Examine the shaft and the body bearings for wear If the shaft shows excessive wear replace it If the body bearing areas are worn replace the body casting Remove the choke shaft from the body carefully so that the friction ball and spring will not fly out of the casing Inspect the shaft and bushings Clean all parts before re assembling the carburetor The metal parts can be cleaned in a good grade of commercial carburetor solvent If the carburetor is not very dirty it can
15. the metering chamber The fuel is Then drawn up through idle fuel adjustment orifice and delivered to the engine through primary idle discharge port The entire carburetor bore from the air inlet to the back of the throttle shutter is at atmospheric pressure during idle operation the ball check valve in the main fuel port is closed to prevent air from entering the metering chamber IDLE SPEED SCREW FUEL INLET SUPPLY CHANNEL INLET SEAT INLET NEEDLE FUEL INLET CONTROL LEVER THROTTLE LEVER the fuel side of the metering diaphragm Atmospheric air pressure on the opposite side will force the metering diaphragm upward causing the diaphragm button to contact the inlet control lever and overcome the inlet tension spring pressure permitting fuel under pressure to force the needle off its seat and enter the metering chamber The fuel then travels from the metering chamber up through the idle and main fuel supply orifices and channels and out the discharge ports to the engine Fuel is delivered from all the discharge ports when the choke is closed to provide a full rich mixture for starting A small amount of air is added to this rich mixture through a hole or port in the choke shutter In all phases of operation the amount of fuel entering the metering chamber is equal to the amount of fuel being used by the engine IDLE MIXTURE SCREW ORIFICE THROTTLE SHUTTER PRIMARY IDLE FUEL DISCHARGE PORT I
16. ttle and under normal full load The mixture should be adjusted to allow the engine to operate at highest RPM The speed will decrease with either an over rich mixture or lean mixture The above procedure need not be repeated each time the engine is started The adjustment will remain in position and will not require frequent re adjustment After the carburetor has been correctly adjusted the engine should start easily To start a cold engine close the choke shutter open the throttle about one quarter of full travel firmly pull the starting cord until the engine Starts open the choke far enough to allow the engine to idle until it has warmed up and can run continuously with the choke fully open To start a warm engine pull the starting cord It should not be necessary to use the choke unless the engine is overheated and fuel vapor is present in the fuel lines o e DO NOT FORCE MIXTURE SCREWS INTO THEIR SEATS ONoOaTARWD w gt OOOO S 7 8 e A sw See y5 l a ow F t HR SERIES CARBURETOR NOMENCLATURE CHOKE SHUTTER BODY MAIN FUEL CHECK VALVE MAIN FUEL DISCHARGE PORT PRIMARY VENTURI SECONDARY VENTURI HIGH SPEED MIXTURE ORIFICE POWER VALVE THROTTLE SHUTTER PRIMARY IDLE DISCHARGE PORT SECONDARY IDLE DISCHARGE PORT IDLE MIXTURE ORIFICE IMPULSE PORT IDLE MIXTURE SCREW METERING CHAMBER DIAPHRAGM GASKET FUEL PUMP GASKET FUEL PUMP DIAPHRAGM PUMP DI
Download Pdf Manuals
Related Search