Home

golden-gun-video-arc..

Contents

1. spo To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CONTROL UNIT 14 1 REMOVING THE CONTROL UNIT Remove the 1P and 2P control units 1P CONTROL UNIT 2P CONTROL UNIT 1 Turn the power off i Remove the 4 screws and pull out the control unit s connector SCREW 4 black NOTE When attaching confirm the direction of the bracket and the cable To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CONTROLUNIT 53 U Disconnect the connector and take the control unit off 4 Remove the screw and take the controller cable bracket off SCREW 1 4 x w flat amp spring washers CONTROLLER CABLE BRACKET To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CONTROL UNIT 14 2 REPLACING THE MICROSWICH There microswitches for the trigger and button inside the control unit 1 3 kinds of screws are used to fasten the L and R covers in place Remove the 10 screws and separate the L and R covers SCREW 8 black M3 x 12 w small flat amp spring washers SCREW 1 black M3 x 10 w small flat amp spring washers COUNTERSUNK HEAD SCREW 1 black M3 x8 i Place cover R face down on the work surface and slowly lift cover L directly upward i Remove the trigger microswitch from the R cover
2. 3 Remove the 2 screws and take the solenoid unit off SCREW 2 M4 x 8 w flat amp spring washers SOLENOID UNIT 4 Be careful not lose or damage the spring and other small parts when removing the solenoid unit To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CONTROL UNIT 5 Remove the 8 screws and the E ring 2 mm and replace the solenoid Be careful not to lose small parts SCREW 8 SOLENOID 2 mm M3 x 8 w spring washer 124 5101 6 Refer to Step 2 to Step 5 and work in reverse order to affix the solenoid unit Refer to the drawing below and be careful with the order in which the small parts are attached and the direction the side with the solenoid wire faces Attaching the parts the wrong way may result in malfunction of the unit or pinching of the wire After replacing the solenoid re assemble the control unit Confirm the microswitches turn on and off properly by pulling the trigger and pushing the button and then attach the L and R covers Be careful not to tighten screws excessively 8 Refer to 11 4 OUTPUT perform the output test To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 COIN SELECTOR IE COIN SELECTOR IMPORTANT e Remove and clean smears using a soft cloth dipped in water or diluted chemical detergent which is then wrung dry e Never apply machine o
3. Are extra coins and incorrect coins properly returned COIN INSERTION SLOT HEJECT BUTTON COIN RETURN SLOT To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 FLUORESCENT LAMP REPLACEMENT FLUORESCENT LAMP REPLACEMENT WARNING Before starting to work be sure to turn the power off Without turning the power off can cause an electric shock or short circuit e You may get burned by a hot fluorescent lamp or other lamps Pay full attention to the lamps when performing the work Be sure to use lamps meeting specified rating Using lamps exceeding the specified rating can cause fire and or accident Such things as deteriorated insulation in lighting fixtures can cause a short circuit and or smoke Make sure there are no abnormalities For example check if you can smell anything burning if any sockets have been discolored and if the lamp has to be replaced frequently N CAUTION e To perform work safely and securely be sure to prepare a stepstool which is in a secure and stable condition Performing work without using the stepstool can cause violent falling down accidents e When fastening plastic parts be careful not to tighten screws and nuts excessively To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 FLUORESCENT LAMP REPLACEMENT 16 1 BILLBOARD 1 Turn the power off r CY 25 ALS
4. www bmigaming com 800 746 2255 1 561 391 7200 REPLACING THE FUSE 63 2 Replace the fuse FUSE 250 V 0 2A 1P SENSOR UNIT 514 5143 200 FUSE 250 V 2A 1P SOLENOID 514 5143 2000 FUSE 250 V 0 2A 2P SENSOR UNIT 514 5143 200 FUSE 250 V 2A 2P SOLENOID 514 5143 2000 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PERIODIC INSPECTION IE PERIODIC INSPECTION The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation Players operate the control unit by touching it and holding it with their hands Clean the control unit on a regular basis and have hand wipes etc available to ensure that players will always fully enjoy the game N WARNING Have work performed by site maintenance personnel or other qualified individuals Do not allow people without proper knowledge and technical expertise to work on the product Otherwise there could be an electric shock or other serious accident Also customers could be injured while operating the product Be sure to check once a year to see whether power cables are damaged the plug is securely inserted dust has accumulated between the socket outlet and the power plug etc Using the product with accumulated dust can cause fire and electric shock Periodically around once a year get in touch with the place of contact herein stated
5. Places subject to any type of violent impact Vicinity of anti disaster facilities such as fire exits and fire extinguishers Areas where the temperature exceeds the applicable temperature ambient temperature range of 5 to 30 degrees centigrade Be sure to check the Electrical Specifications Ensure that this product is compatible with the location s power supply voltage and frequency requirements A plate describing Electrical Specifications is attached to the product Non compliance with the Electrical Specifications can cause a fire and electric shock This product requires a breaker and earth mechanism as part of the location facilities Using the product without these can cause a fire and electric shock Be sure to use an independent power supply equipped with an earth leakage breaker Using a power supply without an earth leakage breaker can cause an outbreak of fire if a power surge occurs Putting many loads on one electrical outlet can cause generation of heat and a fire resulting from overload Ensure that the indoor wiring for the power supply is rated at 15 A or higher AC single phase 100 V 120 V area and 7 A or higher AC 220 V 240 V area Non compliance with the Electrical Specifications can cause a fire and electric shock When using an extension cord ensure that the cord is rated at 15 A or higher AC 100 V 120 V area and 7 A or higher AC 220 V 240 V area Using cord rated lower than the specified
6. to remove glass holder bracket gem Stand on a stepstool when replacing FL unit For safety reasons this should be done together with at least 2 people Replace the fluorescent lamp NOTE Replace the glow lamp if necessary To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 REPLACING THE FUSE REPLACING THE FUSE WARNING In case fuse replacements other than those stated in this manual are necessary contact where you purchased the product from for inquiries regarding this matter In order to prevent an electric shock be sure to turn power off and unplug from the socket outlet before performing work by touching the internal parts of the product Be careful not to damage the wire Damaged wires may cause electric shock or short circuit or present a fire risk Be sure to use fuses meeting specified rating Using fuses exceeding the specified rating can cause fire and electric shock accidents After eliminating the cause of the blowing of fuse replace the fuse Depending on the cause of fuse blowing continued use with the fuse as is blown can cause generation of heat and fire hazard N CAUTION For continued protection against risk of fire replace only with the same type of fuse having the same electrical ratings 1 Turn the power off I Remove the 8 screws and remove back cover To Purchase This Machine Please Visit BMI Gaming
7. 7200 RINGWIDE 20 2 CLEANING THE RINGWIDE Gror IMPORTANT Clean the RINGWIDE once a year or when Error 0090 or Error 0091 is displayed If dust accumulates inside the RINGWIDE it could lead to malfunction and other trouble Take the RINGWIDE off once a year and use a vacuum cleaner to clean the areas around the intake and exhaust vents and where it is attached to the cabinet 1 Refer to 20 1 REMOVING THE RINGWIDE and take the RINGWIDE off from the cabinet Clean around the air vent of the RINGWIDE with a vacuum cleaner AIR INTAKE Clean around installment parts of the RINGWIDE in the cabinet with a vacuum cleaner Be sure not to damage wirings and boards Electronic devices on boards may damage by static electricity and be sure not to vacuum electronic devices by a vacuum cleaner Refer to 20 1 REMOVING THE RINGWIDE and work in reverse order to attach the RINGWIDE to the cabinet To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 RINGWIDE 20 3 COMPOSITION OF THE RINGWIDE IMPORTANT e The RINGWIDE becomes the RINGWIDE for this product once the key chip is inserted e The DIP SW dip switches on the RINGWIDE must be set as specified below If set incorrectly for this product an error will be displayed and the game will not run ASSY CASE WDE W 1GB USA 847 0001D 01 DIP SW Setting Use this product with the DIP SW settings shown
8. Alternatively use the kit number below to arrange for a drive XKT 1515 01 DVD DRIVE KIT FOR LBG ENG Part name Part no Diagram Use etc Quantity DVD DRIVE SERVICE MANUAL 420 6923 01 DVD DRIVE 610 0719 03 For software installatior DVD WIRE 605 0094 For software installation To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ASSEMBLY AND INSTALLATION 3 ASSEMBLY AND INSTALLATION WARNING Perform assembly work by following the procedure herein stated If instructions are not followed or if tasks and or checks are neglected an electric shock or other very serious accident even fatal accident can occur Also customers could be injured while operating the product Be careful not to damage the wires Damaged wires may cause electric shock or short circuit or present a risk of fire Provide sufficient space so that assembling can be performed Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difficult To perform work safely and avoid serious accident such as the cabinet falling down do not perform work in places where step like grade differences a ditch or slope exist When assembling more than one person is required Depending on the assembly work there are some cases in which working by one person alone can cause personal injury or parts damage Ensure that connectors are properly connected Im
9. PANEL1 LAMP PANEL2 LAMP PLAYERI CONTROLLER REACTION PLAYER2 CONTROLLER REACTION 3 EXIT SELECT WI TH SERVI CE BUTTON AND PRESS TEST BUTTON OUTPUT TEST screen m Controls Use the SERVICE Button to move the cursor to the desired test item On the PANEL 1 2 LAMP settings the value changes each time the TEST Button is pressed switching to a different color When the TEST Button is pressed for other selected items OFF will change to ON and the corresponding output device will operate If the TEST Button is pressed for an item that is ON the device will change to OFF and stop operating Select EXIT and press the TEST Button The GAME TEST MENU screen reappears a Venu Items START1 LAMP Player 1 START Button lamp START2 LAMP Player 2 START Button lamp PANEL1 LAMP LED panel lights up in a shape See 1 on the figure in below Cycle setting from 1 through 7 to change colors PANEL2 LAMP LED panel lights up in an X shape See 2 on the figure in below Cycle setting from 1 through 7 to change colors PLAYER1 CONTROLLER REACTION Activates the solenoid in Player 175 control unit Reverts to OFF after one activation PLAYER2 CONTROLLER REACTION Activates the solenoid in Player 2 s control unit Reverts to OFF after one activation To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE 11 5 GAME ASSIGNMENTS All sett
10. boss s weak point drains the boss s LIFE gauge significantly When the boss begins an attack a cancel gauge will sometimes appear As the boss approaches the player the cancel gauge changes from green to yellow orange and finally red according to the danger level The boss s attack can be avoided by forcing the cancel gauge down to zero BOSS S LIFE GAUGE BOSS S CANCEL GAUGE BOSS BATTLE screen Shooting the boss drains the boss s LIFE gauge When the boss s LIFE gauge reaches zero the boss is defeated GAME OVER If both players run out of LIFE the game ends LIFE is shown as burning fire 1 If you want to join the game during play insert coins and press the START button at any time If there are enough credits remaining to play the START button on the side with no one playing flashes continuously Join the game by pressing the flashing START button 2 When all LIFE is lost the CONTINUE message is displayed If you wish to CONTINUE insert the required number of coins and press the START button again If there are enough credits remaining to CONTINUE you can join again by pressing the START button NOTE The number of credits required to continue can be set in SYSTEM TEST MODE Refer to 10 SYSTEM TEST for details 2 If your total points rank among the top 10 after completing all the stages in the game you can enter your name To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2
11. circuits or fires When connecting a connector check the direction carefully Connectors must be connected in only one direction If indiscriminate loads are applied in making connections the connector or its terminal fixtures could be damaged resulting in electrical shock short circuits or fires N CAUTION When opening closing or attaching or removing the doors or the other parts be careful that your hand or finger does not get caught in anything e Static electricity from human body may damage some electronics devices Before handling starting to work touch a grounded metallic surface so that the static electricity can be discharged e The product s settings are changed in TEST MODE If using only one machine the RINGWIDE DIP SW setting does not need to be configured Leave RINGWIDE on the default setting Changing it could cause malfunctions or damage to the parts To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 RINGWIDE 20 1 REMOVING THE RINGWIDE The RINGWIDE is inside the left side front door of the cabinet on the left side when facing the screen Remove the entire wooden board ASSY MAIN BD on which the RINGWIDE is placed 1 Turn the power off i Unscrew 8 screws and remove back cover 2 Disconnect all connecters connected to the RINGWIDE To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391
12. due to the empty weight of the cabinet and may cause personal injury When moving the DLP projector do not push it from the rear side Push it from sideways Pushing the DLP projector from the rear side can have the DLP projector fall down causing personal injury etc In case the floor has slanted surfaces or step like differences be sure to move the machine by 2 or more persons Never disassemble the unit in ways other than those described in this manual Doing so can cause accidents such as electric shocks short circuits and fires N CAUTION e Do not hold or press the plastic parts as indicated by the figure Failure to observe this instruction may break the parts and eventually the broken pieces may cause a personal injury e When moving the cabinet push on the parts made of sheet metal or by holding the handles Putting fingers into the coin return or other open slots or opening doors and holding the machine by the door frames could damage the edges or may result with fingers getting shut in the doors e If the machine is going to be moved somewhere on a different level disassemble it into the individual units before doing so If the machine is tilted or the cabinet is set on an uneven surface the joints may break e Do not allow ropes to come in contact with the surface of the machine directly or they may scratch it Put some kind of protective material under the rope where it Will touch the machine e When moving the ca
13. e This work should be performed by the site maintenance individual or other skilled professional Work performed by non technical personnel can cause malfunctioning e order to prevent electric shock and short circuit hazards be sure to turn the power off before performing work e Be careful not to damage the wires Damaged wires may cause electric shock or short circuit or present a risk of fire When the game machines of a same or similar type are installed side by side their sensors may interfere with each other To reject the interference follow the procedure below The following game machines employ a same or similar type of sensor If interference happens to the sensors operation of the games may be mutually disturbed THE HOUSE OF THE DEAD 2 U R type DX type and Super DX type DEATH CRIMSON U R type and DX type THE LOST WORLD U R type DX type and Super DX type BRAVE FIRE FIGHTERS SAMBA DE AMIGO CONFIDENTIAL MISSION U R type and DX type SHAKATTO TAMBOURINE LUPIN THE 3RD THE SHOOTING U R type and DX type THE MAZE OF THE KINGS U R type and DX type THE HOUSE OF THE DEAD 3 U R type and DX type VIRTUA COP 3 U R type and DX type GHOST SQUAD U R type and DX type THE HOUSE OF THE DEAD 4 DX type and SPECIAL type 2SPICY RAMBO Ai Sareru Yori Ai Shitai SEGA GOLDEN GUN 7 Turn the power off i i Remove the 8 screws and take back cover off To Purchase This Machine P
14. may appear and the product may not operate as intended COIN ASSIGNMENTS COIN CHUTE TYPE COMMON SERVICE TYPE COMMON NETWORK SETTING DHCP ENABLE The GAME COST SETTING screen in COIN ASSIGNMENTS appears as follows COIN ASSI GNMENTS GAME COST SETTI NG credit s to start credit s to continue credit s to premium start credit s to exchange EXIT SELECT WITH SERVI CE BUTTON AND PRESS TEST BUTTON Menu Items credit s to start Sets the number of credits required to start the game credit s to continue Sets the number of credits required to continue credit s to premium start Sets the number of credits required for Premium Start credit s to exchange Sets the number of credits required for Exchange Chance To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE GAME TEST MODE IMPORTANT e To change settings in the GAME TEST MODE simply making changes on the setting screen will not be effective Complete the TEST MODE in normal fashion e Use with the specified settings If settings other than those specified are used inappropriate operations or malfunction may occur 11 1 GAME TEST MENU Select GAME TEST MENU from the SYSTEM TEST MODE screen to display the GAME TEST MENU screen as follows GAME TEST MENU BOOKKEEPI NG NPUT TEST OUTPUT TEST GAME ASSI GNMENTS OPTI ASSI GNMENTS CONTROLLER
15. over them for instance and easily damage them Additionally if these lines are damaged there could be a risk of electrical shock or short circuit Set these lines at locations where they will not interfere with customer traffic or attach covers to them After laying out the power cable on the floor be sure to always protect it If the power cable is left exposed it can easily be damaged resulting in electrical shock For safety reasons be sure to first connect the power cable to the product If the power cable is first connected to the power plug an accident such as an electric shock or short circuit may occur If grounding has been established with the earth wire inside the power cable do not perform grounding with the AC unit earth terminal Conversely if the AC unit earth terminal has been used for grounding do not establish ground with the earth wire in the power cable Otherwise there could be faulty or erroneous operations To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 1 6 ASSEMBLY AND INSTALLATION The AC unit has main switch circuit protector and the inlet which connects the power cable 1 Confirm that the AC unit power switch is at OFF Main switch OFF 2 Connect one end of the earth wire to the AC earth terminal and the other end to the indoor earth terminal The accessory power cable contains earth wire Connect power cable to AC unit inlet and then
16. the accurately grounded indoor earth terminal by using an earth wire Unless the product is grounded appropriately the user can be subject to an electric shock After performing repair etc for the control equipment ensure that the earth wire 1s firmly connected to the control equipment Ensure that the power supply used is equipped with an earth leakage breaker Using a power supply which is not equipped with the earth leakage breaker can cause a fire when earth leakage occurs Besure to use fuses which meet the specified rating Only for the machines which use fuses Using fuses exceeding the specified rating can cause a fire and an electric shock To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Specification changes removal of equipment conversion and addition not designated by SEGA are not allowed The parts of the product include warning labels for safety covers for personal protection etc It is very hazardous to operate the product by removing parts and or modifying the circuits Should doors lids and protective parts be damaged or lost refrain from operating the product and contact where the product was purchased from or the office herein stated SEGA shall not be held responsible for any accidents compensation for damage to a third party resulting from the specifications not designated by SEGA Ensure that the product meets the requirements of appropriate el
17. the same parts are the boards along the straight sections of the mask and there are 2 types After exchanging the LED board enter TEST MODE and perform a controller adjustment See 11 7 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 RINGWIDE Ei RINGWIDE WARNING Before starting to work be sure to turn the power off Without turning the power off can cause an electric shock or short circuit Be careful not to damage the wires Damaged wires may cause electric shock or short circuit or present a risk of fire Do not expose the game board etc Failure to observe this can cause electric shock hazard or malfunctioning This product does not use any connectors other than those connected to and used by the game board when it leaves the factory Do not needlessly connect wires to unused connectors This could lead to overheating generation of smoke and burn related injuries Have work performed by site maintenance personnel or other qualified individuals Do not allow people without proper knowledge and technical expertise to work on the product Otherwise there could be an electric shock or other serious accident Also customers could be injured while operating the product When returning the game board after making repairs or replacements make sure that there are no errors in the connection of connectors Erroneous connections can lead to electrical shock short
18. wires together inside the control unit Doing so can lead to connection failures with the connectors inside the unit If the tie must be cut to replace wires or perform other such work make sure that they are returned to the original position and tied together again e Once the product has been disassembled use slack preventive agent product No 090 0012 N Coat screws with suitable amounts of this agent and then tighten them If this agent is not used the product might start rattling or come apart e Use the slack preventive agent prescribed in these instructions If any other agent is used there could be chemical changes that inhibit the use of screws and part surfaces could be damaged e Be careful not to damage or lose small parts or screws e When a part has been replaced be sure to always make adjustments and check conditions in TEST MODE To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CONTROL UNIT If the control unit does not operate satisfactorily and adjustments in TEST are ineffective it could be that parts inside the control unit have been damaged Follow the steps given below to remove the control unit then take it apart and replace parts To replace parts in the control unit detach the L and R covers of the outer part Because internal parts are inserted on the R cover side work with the R cover facing downward uU iss a s
19. wiring connectors correctly and securely connected Unless connected in the correct way connector connections can not be made accurately Do not insert connectors forcibly Do power cables have cuts and dents Are all accessories available Can all doors and lids be opened with the accessory keys Can doors and lids be firmly closed To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TABLE OF CONTENTS E0 1011 TABLE OF CONTENTS BEFORE USING THE PRODUCT BE SURE TO READ THE FOLLOWING TABLE OF CONTENTS i INTRODUCTION iv Definition of Site Maintenance Personnel or Other Qualified 0 0 0 6 V HANDLING PRECAUTIONS 1 PRECAUTIONS REGARDING INSTALLATION LOCATION 3 2 14 LIMITATIONS OF USAGE 3 2 2 OPERATION AREA 4 PRECAUTIONS REGARDING PRODUCT OPERATION 5 4 1 BEFORE OPERATION 5 3 2 PAYING ATTENTION TO CUSTOMERS 7 ACCESSORIES 9 ASSEMBLY AND INSTALLATION 11 6 1 ATTACHING THE BOARD ss 13 6 2 INSTALLING THE ss 14 6 3 CONNECTING THE POWER CABLE AND EARTH 15 6 4 ASSEMBLING CHECK 17 7 PRECAUTIONS WHEN MOVING THE MACHINE 22 420 7318 01 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 II TABLE OF CONTENTS came DESCRIPTION 23 8
20. 1 CONTROLLER PRESS TEST BUTTON TO EXI T CONTROLLER ADJUSTMENT screen m Controls 1 Align the top of the groove on the control unit s rear sight with the horizontal line of the plus sign on the screen y i Align the top of the control unit s front sight with the horizontal line as well 3 Pull the trigger when the top of the rear sight and top of the front sight line up with the center of the plus sign on the screen To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE Shoot the upper left then the lower right and finally the center of the screen to complete the process The screen will display NOW CALCULATING 5 When the calibration screen is complete check to make sure the mark targeting sight is properly displayed PLAYER1 CONTROLLER ADJ USTIVENT PLAYER1 CONTROLLER MARK CHECKI NG TEST BUTTON TO MEMRI ZE SERVI CE BUTTON TO CANCEL CONROLLER ADJUSTMENT screen MARK CHECK SETTING screen Press the SERVICE Button to exit to the CONTROLLER CALIBRATION SETTING screen without saving calibration settings DEFAULT ADJUSTMENT Set the values for the control units to default 6 Press the TEST Button to save calibration settings and return to the CONTROLLER CALIBRATION PLAYER1 CONTROLLER ADJ USTIVENT TEST BUTTON TO SET DEFAULT SERVI CE BUTTON TO CANCEL DEFAULT ADJUSTMENT screen m Controls Press the TEST Button to reset settings to
21. 1 LAM PANEL2 LAM PLAYER1 CONTROLLER REACTI ON PLAYER2 CONTROLLER REACTI ON gt EXIT SELECT W TH SERVI CE BUTTON AND PRESS TEST BUTTON OUTPUT TEST screen To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ASSEMBLY AND INSTALLATION 5 CONTROLLER ADJUSTMENT When CONTROLLER ADJUSTMENT is chosen from CONTROLLER CALIBRATION SETTING under GAME TEST MENU screen a screen for adjusting the Control Unit crosshair will be displayed Before operating the product always play the game to verify that there are no irregularities during play and that the crosshair does not require adjustment Though the crosshair is adjusted at the factory adjustment may be required in some situations because the product is disassembled for shipment See 11 7 PLAYER1 CONTROLLER ADJ USTIVENT EE PLEASE SHOOT GRI D W TH PLAYERI CONTROLLER PRESS TEST BUTTON TO EXIT CONTROLLER ADJUSTMENT screen NOTE Strong lighting located near the monitor other machines in the surrounding area and other objects may have an effect on the controller adjustment The above inspections 1 4 should be conducted regularly as part of a monthly inspection However 5 CONTROLLER ADJUSTMENT should be conducted once per week To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ASSEMBLY AND INSTALLATION THE INTERFERENCE PREVENTION WIRING N WARNING
22. 255 1 561 391 7200 WIRING DIAGRAM 86 D 3 3 IR m LI E kl r LE eem a ER MERI E NB B liliI LI CCCCCCCO m um lt lt ils Ea UNE s 2i a l l l l l a III II III I I I l LD mimm m pn n Ra SS LI 11 TITLITTI ms za u z za rr T
23. 255 1 561 391 7200 GAME DESCRIPTION 8 2 SPECIAL FEATURES These are special features to encourage users to play the game Each feature can be turned ON OFF and its effects adjusted in TEST MODE PREMIUM START CHANCE Using extra credits to start the game allows players to start in a powered up state Both Players 1 and 2 have only a single chance to do this The Premium Start Chance feature cannot be used twice TOW CREDIT S REQUIRED TIME LIMIT CREDIT S INSERTED m Controls The OK button lights up when the number of credits inserted meets the requirement for a Premium Start Shooting the OK button when it is lit up causes the game to start powered up at the cost of credits Shooting the EXIT button causes the game to start normally Menu Items Can be set from 1 to 10 in TEST MODE Default setting 2 Can be set from 1 to 9 in TEST MODE Default setting 1 Can be set from 1 to 10 in TEST MODE Default setting 2 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME DESCRIPTION EXCHANGE CHANCE NOTE Scores achieved with this feature cannot be entered in the score rankings at the end of the game Players can spend credits in items shops to gain extra score which can then be used to purchase items Both Players 1 and 2 have only a single chance to do this The Exchange Chance feature
24. 4 i 23 8 2 SPECIAL FEATURES 000 28 AND COIN METER 31 system TEST MODE 33 GAME TEST MODE 34 11 1 GAME TEST MENU s 34 11 2 BOOKKEEPING 2000 35 11 3 INPUT TEST 37 11 4 OUTPUT TEST 38 11 5 GAME ASSIGNMENTS s 39 11 6 OPTION s 40 11 7 CONTROLLER CALIBRATION 8 41 11 8 BACKUP DATA CLEAR s 44 conTROL PANEL 45 12 1 REMOVING THE CONTROL 45 12 2 REPLACING THE START K DU TT ON 46 LCD UNIT 48 13 1 CLEANING THE SCREEN s 49 14 CONTROL UNIT 50 14 1 REMOVING THE CONTROL UNIT 52 14 2 REPLACING THE ss 54 143 REPLACING THE SENSOR ss 55 14 4 REPLACING THE SOLENOID s 56 COIN SELECTOR 58 15 1 CLEANING THE COIN SELECTOR 58 15 2 REMOVING THE JAMMED 59 15 3 COIN INSERTION TEST 59 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TABLE OF CONTENTS FLUORESCENT LAMP REPLACEMENT 60 16 1 BILLBOARD 9599 61 REPLACING THE FUSE 62 PERIODIC INSPECTION 64 TROUBLESHOOTING 66 19 1 TROUBLESHOOTING 67 19 2 REPLACING THE LED 68 EJ RINGWIDE 71 20 1 REMOVING THE RINGWIDE
25. CALI BRATI ON SETTI NG BACKUP DATA CLEAR gt EXIT SELECT WITH SERVI CE BUTTON AND PRESS TEST BUTTON GAME TEST MENU screen m Controls Use the SERVICE Button to move the cursor to the desired test item Press the TEST Button to confirm selection of the item Select EXIT and press the TEST Button to return to the SYSTEM TEST MENU screen mMenu Items BOOKKEEPING Displays all recorded game data INPUT TEST Tests each input device used for the game OUTPUT TEST Tests each output device used for the game To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE 11 2 BOOKKEEPING Each game record can be viewed BOOKKEEPING 1 3 COIN 1 COIN 2 TOTAL COI NS COIN CREDI TS SERVI CE CREDI TS TOTAL CREDI TS PRESS TEST BUTTON TO NEXT BOOKKEEPING 1 3 screen m Controls Press the TEST Button to move to BOOKKEEPING 2 3 screen a Menu Items COIN 1 Number of coins inserted in coin chute 1 COIN 2 Number of coins inserted in coin chute 2 TOTAL COINS Total Number of coins inserted in coin chute COIN CREDITS Number of credits for coins inserted SERVICE CREDITS Number of credits entered with the SERVICE Button TOTAL CREDITS Total number of all credits To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE BOOKKEEPING 2 3 NUMBER OF GAMES FIRST PLAY CONTI NUE PLAY
26. EFT SPEAKER OFF RI GHT SPEAKER OFF REAR LEFT SPEAKER OFF REAR RI GHT SPEAKER OFF CENTER SPEAKER OFF WOOFER SPEAKER OFF gt EXIT SELECT W TH SERVI CE BUTTON AND PRESS TEST BUTTON To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ASSEMBLY AND INSTALLATION 3 INPUT TEST When INPUT TEST is chosen from GAME TEST MENU screen a screen to test the game s switches will be displayed Confirm each input device is functioning correctly Normal When the controller is turned towards the screen the word beside SCREEN IN will change to IN If other input devices are operated the word OFF beside the device name will change to ON See 11 3 NPUT TEST PLAYERI PLAYER2 CONTROLLER TRI GGER CONTROLLER X mm CONTROLLER Y SCREEN START OFF SERVI CE OFF TEST OFF PRESS TEST BUTTON AND SERVI CE BUTTON TO EXI T INPUT TEST screen 4 OUTPUT TEST When OUTPUT TEST is chosen from GAME TEST MENU screen a screen to test lamps and their wiring connections will be displayed Confirm each output device is functioning correctly Normal When the TEST Button is pressed the selected item will change from OFF to ON and the corresponding output device will operate If the TEST Button is pressed for an item that is ON the device will change to OFF and stop operating See 11 4 OUTPUT TEST START1 LAMP START2 LAMP PANEL
27. Flower vases flowerpots cups water tanks cosmetics and receptacles containers vessels containing chemicals and water To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PRECAUTIONS REGARDING PRODUCT OPERATION N CAUTION e To avoid injury be sure to provide sufficient space by considering the potentially crowded situation at the installation location Insufficient installation space can cause contact collisions and or trouble between customers e During daily cleaning be sure to check the surface of the parts that the player touches with his her hands for damage cracks or loose screws If a player uses the machine while it is damaged cracked or has a loose screw the player may become injured ETE zal e Exo armi arr papapak Erg teed Ew is irr CE oes prar e Be sure to check carefully there are no gaps rattling at the door or and the junction of the cabinet If there are gaps or rattling the players could get fingers or hands caught resulting in injury e Make sure all the doors are locked securely and that they do not rattle If the doors are not locked properly or there are gaps or rattling the players could get their fingers or hands caught It could also invite mischief e Be sure to perform appropriate adjustment of DLP projector For operation of this machine do not leave monitor s flick
28. MAGAZINE The number of MAGAZINEs the player will gain Can be set between 1 and 10 Default setting 2 Set EXCHANGE CHANCE ON OFF Setting to ON allows players to exchange credits for score items at the item store screen Scores are worth 70 of the set value during 2 player simultaneous play NOTE Cannot be set to ON when set to FREE PLAY Default setting ON SCORE The number of points the player will gain Can be set between 10000 and 90000 in 10000 increments Default setting 10000 Set CONTINUE BONUS ON OFF Setting to ON allows players to get bonus items when continuing NOTE The CONTINUE BONUS setting is not displayed for CABINET TYPE EUROPE the setting defaults to OFF for CABINET TYPE ASIA Cannot be set to ON when set to FREE PLAY To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE 11 7 CONTROLLER CALIBRATION SETTING This screen allows for the adjustment of the control unit s crosshair settings which are used during game play CONTROLLER CALI BRATI ON SETTI NG CONTROLLER MARK CHECK PLAYER1 CONTROLLER ADJ USTIVENT PLAYER1 CONTROLLER DEFAULT AD USTMENT PLAYER2 CONTROLLER AD USTIVENT PLAYER2 CONTROLLER DEFAULT AD USTMENT gt EXIT SELECT WTH SERVI CE BUTTON AND PRESS TEST BUTTON CONTROLLER CALIBRATION SETTING screen m Controls Use the SERVICE Button to move the cursor to the desired test item Press the
29. NOTE The S M referenced in the table denotes RINGWIDE Service Manual which is provided separately Cleaning the Cabinet Surfaces When the cabinet surfaces become dirty remove stains with a soft cloth soaked in water or diluted with water chemical detergent and then wrung dry To avoid damaging the finish do not use such solvents as thinner benzene etc other than ethyl alcohol or abrasives bleaching agent and chemical dust cloth Some general purpose household kitchen and furniture cleaning products may contain strong solvents that degrade plastic parts coatings and print Before using any cleaning product read the product s cautionary notes carefully and test the product first on a small area that is not highly visible To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLESHOOTING TROUBLESHOOTING WARNING If problems other than those covered in this manual arise or if no improvements can be noted after measures given in this manual have been taken do not take measures indiscriminately Cut off the power immediately and contact the office shown in this manual or the dealer from whom the product was originally purchased If the power is left on while there is an abnormality a fire electric shock or other serious accident can occur Before starting to work be sure to turn the power off Without turning the power off can cause an electric shock or
30. PREMIUM START CHANCE EXCHANGE CHANCE TOTAL TI ME PLAY TI ME D wem AVERAGE PLAY TI ME M LONGEST PLAY TI ME M SHORTEST PLAY TI ME M PRESS TEST BUTTON TO NEXT BOOKKEEPING 2 3 screen m Controls Press the TEST Button to move to BOOKKEEPING 3 3 screen a Menu Items BOOKKEEPING 3 3 GAME HISTOGRAM 0M 00S OM 295 0M 305 0M 5295 1M 005 295 1M 305 595 9M 00S 9M 295 9M 305 9M 595 OVER 10M 00S PRESS TEST BUTTON TO EXIT BOOKKEEPING 3 3 screen m Controls Press the TEST Button to return to GAME TEST MENU screen a Venu Items This displays play times on a scale from 0MOOS to 9 595 based on 30 second intervals All play times 10 minutes or over are included in the item OVER 10 005 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE 11 3 INPUT TEST Select INPUT TEST to display the following screen and check the status of input devices This test should be used periodically to check that each input device is functioning correctly NPUT TEST PLAYERI CONTROLLER TRIGGER OFF CONTROLLER X ii CONTROLLER Y d SCREEN IN OUT START OFF SERVICE OFF TESI OFF PRESS TEST BUTTON AND SERVICE BUTTON TO EXIT INPUT TEST screen m Controls PLAYER2 OFF OUT OFF The SCREEN IN setting is normal if it changes from OUT to IN when the control units are pointed at the s
31. TEST Button to change the value of the selected setting To abort calibration press the TEST Button to cancel Select EXIT and press the TEST Button The GAME TEST MENU screen reappears Menu Items CONTROLLER MARK CHECK Checks the gun sights and P2 control units are checked at the same time PLAYERI PLAYER2 Calibrates Player 1 and Player 2 control units CONTROLLER ADJUSTMENT PLAYERI PLAYER 2 Resets Player 1 and Player 2 control units to their factory CONTROLLER DEFAULT ADJUSTMENT default settings To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE CONTROLLER MARK CHECK Check the marks targeting sights for Players 1 and 2 CONTROLLER MARK CHECK Displayed if PLAYER 2 control unit is pointed outside the screen P1 MARK blue P2 MARK is displayed in red PRESS TEST BUTTON TO EXIT CONTROLLER MARK CHECK screen m Controls Point the control units at the screen to display the marks targeting sights OUT OF SCREEN is displayed when the control units are pointed outside the screen Press the TEST Button to return to the CONTROLLER CALIBRATION SETTING screen 1 PLAYER2 CONTROLLER ADJUSTMENT Calibrate PLAYER I PLAYER 2 control units The below image shows the calibration screen for Player 1 The screen for Player 2 is the same PLAYER1 CONTROLLER AD USTIVENT GRID PLEASE SHOOT GHRID WITH PLAYER
32. TRIGGER GOLD SIGHT GOLD CORD FRAME COVER GOLD CORD CLAMP CORD FRAME SOLENOID FRAME SLIDE FRAME SOLENOID DAMPER SOLENOID SPRING SOLENOID SHAFT SOLENOID WSHR WEIGHT DAMPER COLLAR WEIGHT SPRING WEIGHT WSHR SLIDE BASE UPPER BUSH PLUG CUSHION SLIDE BASE LOWER TRIGGER SPRING SW MICRO TYPE SS 5GL2 SUMITUBE F D 20MM SOLENOID DC24V CORD CLAMP SR10 M SCR PH W FS M4x8 M SCR PH W SMALL FS BLK M4x8 M SCR PH W SMALL FS BLK M3x12 M SCR PH W SMALL FS BLK M3x10 HEX SKT ELH CAP STN M3x8 M SCR FH BLK M3x8 E RING 2MM SPR WSHR M3 WH CONTROLLER To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 WIRE COLOR CODE TABLE WIRE COLOR CODE TABLE WARNING The DC power wire color for this product is different from previous SEGA titles Working from the previous wire colors will create a high risk of fire The color codes for the wires used in the diagrams in the following chapter are as follows A PINK B SKY BLUE C BROWN D PURPLE E LIGHT GREEN Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters RED BLUE YELLOW GREEN WHITE ORANGE BLACK GRAY N conn WN If the right hand side numeral of the code is 0 then the wire will be of a single color shown by the left hand side numeral see the above Note 1 If the right hand side numeral is not O that particular wire has a s
33. TRIGGER MICROSWITCH 509 5080 Remove the soldered part and then remove the microswitch Solder and attach the new button microswitch Protect the soldered part with heat shrinkable tubing After replacing the microswitch re assemble the control unit Confirm the microswitches turn on and off properly by pulling the trigger and pushing the button and then attach the L and R covers Be careful not to tighten screws excessively Refer to 11 3 INPUT TEST and perform the input test N OO mA To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CONTROL UNIT 14 3 REPLACING THE SENSOR UNIT 1 Refer to 14 2 REPLACING THE MICROSWITCH and remove the cover L Disconnect the connector and take the sensor unit off SENSOR UNIT GLG 2130 CONNECTOR XA9P 2 After replacing the sensor unit re assemble the control unit Confirm the microswitches turn and off properly by pulling the trigger and pushing the button and then attach the L and R covers Be careful not to tighten screws excessively 4 Refer to 11 7 CONTROLLER CALIBRATION SETTING and perform the aim adjustment To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 56 CONTROL UNIT 14 4 REPLACING THE SOLENOID 7 Refer to 14 2 REPLACING THE MICROSWITCH and remove the cover L I Undo the cord clamp and disconnect the connector CONNECTOR SM2P
34. To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 SEGA m MANUAL To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BEFORE USING THE PRODUCT se sure ro READ THE FoLLOWING To maintain safety To ensure the safe operation of this product be sure to read the following before usage The following instructions are intended for the users operators and the personnel in charge of the operation of the product After carefully reading and sufficiently understanding the warning displays and cautions handle the product appropriately Be sure to keep this manual close to the product or in a convenient place for future reference Herein explanations which require special attention are enclosed with dual lines Depending on the potentially hazardous degrees the terms of DANGER WARNING CAUTION etc are used Be sure to understand the contents of the displays before reading the text Indicates that mishandling the product by disregarding this pictograph will A DANGER cause severe InJury or death AN WARNING Indicates that mishandling the product by disregarding this warning will cause a potentially hazardous situation which can result in death or serious injury N CAUTION Indicates that mishandling the product by disregarding this caution will cause a slight hazardous situation which can result personal injury a
35. binet do not hold it by the control unit or pull on the control unit Doing so could damage the parts or cause them to become deformed To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME DESCRIPTION ES GAME DESCRIPTION 8 1 HOW TO PLAY 1 When you insert coins they will be counted in the credit display at the bottom of the screen When you insert enough coins for a game the message at the bottom will change from INSERT COIN S to PRESS START BUTTON and the start buttons on either side will flash Up to 24 credits can be counted at once Coins inserted after 24 credits are recorded will not be counted or returned However the number of coins inserted will be counted in the data display and the coin meter NOTE The number of credits required for a game can be set in SYSTEM TEST MODE Refer to 10 SYSTEM TEST MODE for details I Which START button you press determines which side you play on Once you press the START button the game begins 2 Once the game starts the video demonstration will play followed by the stage title and then it will go to the actual game GAME SCREEN The score ammo remaining player mark and life of the player playing on the left PLAYER 1 are shown at the left side of the screen while those of the player playing on the right PLAYER 2 are shown at the right side of the screen Credits are always displayed at the bottom of screen If t
36. bmigaming com 800 746 2255 1 561 391 7200 PARTS LIST 3 GLG 0550 D 1 2 ASSY MASK wal AA d LAM SEEA To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PARTS LIST 3 GLG 0550 ASSY MASK ITEM NO PART NO 1 RMB 0551 2 HDF 0531 3 HDF 0532 4 HDF 0534 5 HDF 0535 6 JPT 1082X 7 GLG 0551 8 GLG 0552 101 838 15119 102 280 5009 02 91 201 000 P00408 W 202 050 U00300 203 069 000034 PN 204 FAS 680016 205 050 H00400 206 060 500400 207 060 00400 301 GLG 60029 302 GLG 60030 303 GLG 60031 304 600 7010 0300 D 2 2 DESCRIPTION NOTE SIDE MASK UPPER MASK LOWER MASK MASK JOINT BRKT L MASK JOINT BRKT R IR COVER STICKER MASK LONG STICKER MASK SHORT LED BD HFN G SENSE GLG CORD CLAMP 21 CN M SCR PH W FS M4x8 U NUT M3 FLT WSHR PLASTIC BLK 3 8x1 FLT WSHR NI 3 10x0 5 HEX NUT M4 SPR WSHR M4 FLT WSHR M4 WH 5 1 WH MASK2 WH MASK3 WIRE HARN EARTH VL1P P 0300MM To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PARTS LIST 5 GLG 2050 ASSY LED ITEM NO PART NO DESCRIPTION NOTE 1 GLG 2052 LED BRKT 101 838 14973 02 LED BD RGB 3x2BLOCK 102 280 896 05 SPACER WN 05G HIROSUGI To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PARTS LIST 6 GLG 2060 ASSY BUTTON PLATE Altach th
37. cannot be used twice in a row It can however be used again in a different shop CREDIT S REQUIRED TIME LIMIT SCORE BONUS mm um mm mm mm um um um nm m um um um W a a a Te ee ee mm mm mm n he OK BUTTON EXIT BUTTON CREDIT S INSERTED m Controls The OK button lights up when the number of credits inserted meets the requirement for an Exchange Chance Shooting the OK button when it is lit up causes the game to award a set number of points at the cost of credits and then return to the shopping screen Shooting the EXIT button causes the player to exit the shop and continue the game Menu Item SCORE BONUS Can be set from 10000 to 90000 in increments of 10000 in TEST MODE Default setting 10000 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 30 GAME DESCRIPTION CONTINUE BONUS NOTE This feature is not included for REGION EXP EUROPE 1 When the Continue screen appears an item roulette begins spinning i The player inserts the required number of credits and presses the START button to continue the game 3 The player is awarded whichever item was lit up when the START button was pressed 4 The game
38. continues ROULETTE BONUS ITEM LIT UP To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 SWITCH UNIT AND COIN METER SWITCH UNIT AND COIN METER WARNING Do not touch undesignated places Touching places not designated can cause electric shock or short circuit N CAUTION When opening closing or attaching or removing the doors or the other parts be careful that your hand or finger does not get caught in anything e When you enter the TEST MODE fractional coin and bonus adder data is erased e Adjust the sound to the optimum volume taking into consideration the environmental requirements of the installation location e Removing the coin meter circuitry renders the game inoperable In TEST MODE the switch unit in the coin chute door is operated Unlock and open the coin chute door Inside is a switch unit SWITCH UNIT TEST BUTTON SERVICE BUTTON SOUND VOLUME SWITCH lan TEST Button Activates TEST MODE Becomes the button to confirm selections in TEST TEST MODE SERVICE Button Makes it possible to enter credits for service without increasing the coin meter SERVICE Becomes the button to select items in TEST MODE SOUND VOLUME Knob Controls the volume for the speakers to the left and right of the control panel SOUND VOLUME Turn the knob to the right to increase speaker volume To Purchase This Machine Please Visit BMI Gaming www b
39. creen Settings other than SCREEN IN are normal if they change from OFF to ON when the corresponding input device is operated Press the TEST Button and the SERVICE Button simultaneously to return to GAME TEST MENU screen Menu Items CONTROLLER TRIGGER This will say ON when the triggers on the control units are being pulled and OFF when they are released CONTROLLERX X This shows the aim location for the X direction on the control units shows the aim location for the X direction on the control This shows the aim location for the X direction on the control units Y This shows the aim location for the Y direction on the control units SCREEN IN This will say IN when the control units are aimed inside the screen and OUT when they are aimed outside the screen START This will say ON when the START buttons are being pressed and OFF when they are released SERVICE This will say ON when the SERVICE Button is being pressed and OFF when it is released TEST This will say ON when the TEST Button is being pressed and OFF when it is released To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE 11 4 OUTPUT TEST This screen 15 for confirming the proper operation of each output device used by the game Periodically use this screen to check the status of each output device OUTPUT TEST START1 LAMP START2 LAMP
40. de with the controls or the player possibly resulting in accidents To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PRECAUTIONS REGARDING PRODUCT OPERATION N CAUTION Be sure to instruct the adult responsible for their children to watch them Children cannot sense danger Approaching the player during play may result in accidental contact collisions or falls If the control unit is pulled from the controller holder and dropped on the head it may cause injury Caution the player not to wrap the control unit cable around his her wrist or neck as this can lead to serious injury Immediately stop users from leaning or sitting on the controller panel Such acts can lead to injury or damage to parts or the shape of the cabinet Immediately stop users from swinging or reloading the control unit in a violent manner Such acts may hurt the user or other people around them Playing too close to the cabinet may cause the control unit to hit the cabinet and cause damage Make sure that players understand to play at a safe distance from the cabinet Make sure that players understand not to stand too close together when playing a 2 player game Swinging the control unit could lead to a player getting hit and may cause injury Instruct players to hold the control unit securely while playing If the Control Unit is dropped it could cause injury to the player Items such as large finger r
41. der to avoid accidents check the following before starting the operation e To ensure maximum safety for the players and the customers ensure that where the product is operated has sufficient lighting to allow any warnings to be read Operation under insufficient lighting can cause bodily contact with each other hitting accident and or trouble between customers e Be sure to perform appropriate adjustment of the monitor For operation of this product do not leave monitor s flickering or deviation as is Failure to observe this can have a bad influence upon the players or the customers physical conditions e 15 suggested to ensure a space al players who feel sick while playing to take a rest e Check if all of the adjusters are in c with the surface If they are not the can move and cause an accident Ensure that all of the adjusters are in contact with the floor e Do not put any heavy item on this product Placing any heavy item on the product can cause a falling down accident or parts damage e Do not climb on the product Climbing on the product can cause falling down accidents To check the top portion of the product use a stepstool e To avoid electric shock check to see if door and cover parts are damaged or omitted e Do not place the following items on top of the product nearby the product or hang them from the ceiling Doing so could result in electric shock short circuits and or damage to the parts
42. e iiem 007 in direcive inside ITEM NO PART NO DESCRIPTION NOTE 1 GLG 2061 BUTTON PLATE 2 421 12771 STICKER DENOMI BLANK 101 909 6077 SW PB OBSA 45UM W 1FLED W 12V 301 GLG 60025 WH START BUTTON PLATE To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PARTSLIST 81 27 GLG 2100 D 1 2 CONTROL UNIT pip pacer un indien ra NN __ 1 The bee the core x inim us D HI I N m TD N m 15 20 421 2 in 000 007 GHEASE ME A Sore components mri e Three Bord 14H on To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PARTS LIST 27 GLG 2100 01 CONTROL UNIT ITEM NO 101 102 103 104 201 202 203 204 205 206 207 208 301 PART NO GLG 2130 APA 2101 04 APA 2102 04 APA 2103 01 APA 2104 04 APA 2106 03 APA 2107 APA 2108 APA 2109 APA 21 10 01 APA 2111 APA 2112 APA 2113 APA 2114 APA 2115 APA 2116 APA 2117 APA 2118 APA 2119 APA 2123 01 APA 2124 APA 2120 CTF 2123 509 5080 310 5029 D20 124 5101 91 280 7881 000 P00408 W FAS 000188 FAS 000100 FAS 000099 FAS 290110 000 F00308 0B 065 E00200 060 500300 60035 D 2 2 DESCRIPTION NOTE SENSOR UNIT OMJ GZH200HFXA COVER LEFT GOLD COVER RIGHT GOLD
43. e right A single person working alone can lead to injury If the light from the 2 LEDs cannot be seen then there is a problem or malfunction Follow the steps below to exchange them You can also use the following steps to clean the screen 1 Turn the power off Replacement is required when the light from 2 LEDs cannot be seen i Unscrew 7 screws on both side of monitor cover Unscrew 4 screws on top of monitor cover To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLESHOOTING 69 CONNECTOR 4 Disconnect 2 connectors 5 The mask has the LED boards attached Remove the 2 U nuts holding the malfunctioning board disconnect both connectors and remove and replace the LED board Be sure not to lose the plastic washers Attach the LED board after checking to make sure it 15 facing the same way as before To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 70 TROUBLESHOOTING 5 The mask has the LED boards attached Remove the 2 U nuts holding the malfunctioning board disconnect both connectors and remove and replace the LED board Be sure not to lose the plastic washers Attach the LED board after checking to make sure it is facing the same way as before 6 If the problematic LED board is in the corner of the mask remove the 5 screws and remove the joint bracket The joint bracket has
44. ectrical specifications Before installing the product check for electrical specifications SEGA products have a nameplate on which electrical specifications are described Ensure that the product is compatible with the power supply voltage and frequency requirements of the location Using any electrical specifications different from the designated specifications can cause a fire and an electric shock Install and operate the product in places where appropriate lighting is available allowing warning labels to be clearly read To ensure safety for the customers labels and printed instructions describing potentially hazardous situations are applied to places where accidents can be caused Ensure that where the product is operated has sufficient lighting allowing the warnings to be read If any label 1s peeled off apply it again immediately Please place an order with where the product was purchased from or the office herein stated When handling the monitor be very careful Applies only to products with monitors Some of the monitor parts are subject to high tension voltage Even after turning off the power some portions are still subject to high tension voltage sometimes Monitor repair and replacement should be performed only by those technical personnel who have knowledge of electricity and technical expertise Be sure to adjust the monitor properly Applies only to products with monitors Do not operate the product leaving on scree
45. ering or deviation as is Failure to observe this can have a bad influence upon the players or the customers physical conditions e Prepare a place where players can rest if they feel sick IMPORTANT e Players directly hold the controller with their bare hands so it is recommended that wet towels paper towels be provided e Placing the DLP projector near halogen lamps or other types of light fixtures which emit strong light may cause a malfunction Make sure to install the projector at a reasonable distance from such sources of light To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PRECAUTIONS REGARDING PRODUCT OPERATION 3 2 PAYING ATTENTION TO CUSTOMERS To avoid injury and trouble be sure to pay attention to the behavior of visitors and players N WARNING For safety reasons do not allow any of the following people to play the game Failure to observe this warning could result in serious injury Those who need assistance such as the use of apparatus when walking Those who are intoxicated or under the influence of drugs Persons who disregard the product s warning displays e Instruct those who feel sick during play to have a medical examination e To avoid injury from falls and electric shocks due to spilled drinks instruct the player not to place heavy items or drinks on the product e To avoid electric shocks and short circuits do not allow custom
46. ers to put hands and fingers or extraneous matter in the openings of the product or small openings in or around the doors e To avoid falls and resulting injury immediately stop the customer from leaning against or climbing on the product etc To avoid electric shock and short circuit do not allow customers to unplug the power plug without a justifiable reason N CAUTION e For safety reasons do not allow any of the following people to play the game Failure to observe this caution could result in an accident or injury Those who have experienced muscle convulsion or loss of consciousness when playing video games etc Those who are not in good health Pregnant women Persons susceptible to motion sickness Those who have high blood pressure or a heart problem Those who have neck or spinal cord problems Even players who have never been adversely affected by light stimulus might experience dizziness or headache depending on their physical condition when playing the game Small children are especially likely to experience these symptoms Caution guardians of small children to keep watch on their children during play Immediately stop such violent acts as hitting and kicking the product Such violent acts can cause parts damage or falling down resulting in injury due to fragments and falling down Persons other than the player should not be allowed to touch the controls during play They may brush against or colli
47. f sound volume Adjust the sound volume lt See Chapter 9 gt Failure of the Board and Amplifier Contact the customer service center listed in this manual Sights are not aligned due to Perform sighting adjustment in the changes in the surrounding TEST MODE lt See 6 10 gt environment The circuit protector functioned due to the momentary overload Failure of the LED board Check to ensure that the LED lights up If it does not light up replace lt See 19 2 gt Failure of the sensor unit Replace the sensor unit GLG 2130 SENSOR UNIT lt See Chapter 14 3 gt Wipe off soiled surfaces Use an Input Test to make sure they change between ON and OFF If they do not exchange the faulty LED board and LED board cover are contaminated Failure of the microswitches microswitches 509 5080 SW MICRO TYPE See 14 2 Failure of the LED board Check that the LEDs are on If not replace them See 19 2 Failure of the sensor unit Replace the sensor unit See 14 3 Fluorescent lamp and glow lamp Replace the fluorescent lamp grow need replacement lamp See Chapter 16 Fuse need replacement Replace the fuse See Chapter 17 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLESHOOTING 19 2 REPLACING THE LED BOARD N CAUTION Removing or attaching of the mask must be carried out by at least 2 people one on the left and one on th
48. here is no player the required number of credits 1s displayed instead ITEM TIME LIMIT AMMO REMAINING PLAYER MARK GAME screen CREDITS CREDITS REQUIRED RELOADING When the player fires all ammo remaining the gun will be empty The player can then reload the weapon by aiming it outside the screen The player can reload this way even if there are still bullets left The gun is also reloaded automatically when the trigger is pulled with no ammo remaining However this type of reload takes longer than a normal reload To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 24 GAME DESCRIPTION SCORE ITEMS Various score items appear when the player shoots treasure boxes or hidden boxes in the background Hidden box appear when the player aims at certain secret areas Picking up score items increases the player s score by various amounts based on the type of item Shooting fireworks boxes causes explosions that defeat nearby enemies Coin 200 Silver Ingot 400 Gold Ingot 600 Sword 800 Fan 41 000 Ginseng 42 000 Drum 100xmax 20 y Fireworks Box To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME DESCRIPTION SHOP ITEMS In each stage the player meets an item merchant twice The player can purchase various weapons and items from the merchant For each stage the player ad
49. ignored may result in the mishandling of the product and cause faulty operation or damage to the product SPECIFICATIONS 46 inches Width x 62 inches Depth To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 INTRODUCTION V Definition of Maintenance Personnel Other Qualified Individuals WARNING Procedures not described in this manual or marked as to be carried out by site maintenance personnel or other qualified professionals should not be carried out by personnel without the necessary skill or technology Work carried out by unqualified persons may cause serious accidents including electrocution Parts replacement maintenance inspections and troubleshooting should be carried out by site maintenance personnel or other qualified professionals This manual includes directions for potentially dangerous procedures which should only be carried out by professionals with the appropriate specialized knowledge The site maintenance personnel or other qualified professionals mentioned in this manual are defined as follows Site maintenance personnel Individuals with experience in maintaining amusement equipment vending machines etc working under the supervision of the owner operator of this product to maintain machines within amusement facilities or similar premises by carrying out everyday procedures such as assembly maintenance inspections and replace
50. il greace etc to the coin selector e After cleaning the coin selector properly insert a standard coin to ensure that the selector functions correctly 15 1 CLEANING THE COIN SELECTOR The coin selector should be cleaned once per month When cleaning follow the procedures below 7 Turn the power off Open coin chute door 2 Open gate and wipe away dirt with animal hairbrush or other soft brush Soak a soft cloth in water or in a neutral cleaning agent diluted with water wring it tightly and wipe away dirt Remove cradle When removing the retaining ring E ring be careful not to bend the rotary shaft A 5 Use soft cloth to wipe dirt from rotary shaft and bearing 6 After wiping off dirt wipe away moisture with a dry cloth and make sure that the coin selector is completely dry To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 COIN SELECTOR 15 2 REMOVING THE JAMMED COIN When the REJECT button fails to refund coins open the coin chute door and open the selector gate Once the jammed coin is removed insert a standard coin to ensure that the selector is working properly 15 3 COIN INSERTION TEST Carry out a coin insertion test once per month At the same time check the following points Does the coin meter count properly Do coins drop into the cashbox correctly Are coins rejected when inserted while holding down the REJECT button
51. ilure to observe this can have a bad influence upon the players or the customers physical conditions e If the adjustment method in this manual does not resolve the problem contact the customer service number in this manual or your supplier e There is no way of knowing when the LCD light is going to cease to function Once it ceases to function the LCD unit will be unable to display anything and the product cannot be used e Do not stick tape stickers or anything else onto the screen Any kind of adhesive may damage the surface of the screen To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 DLP PROJECTOR 13 1 CLEANING THE SCREEN IMPORTANT Since the LCD screen is susceptible to damage pay careful attention to its handling Do not clean the screen with volatile chemicals solvents or alkaline acidic cleaners Clean the screen surface once a week Dip a soft cloth in water 40 degrees or below wring it out firmly and use it to gently wipe the screen If there are stains that can t be removed with warm water use a neutral detergent diluted to 2 3 Refrain from using other chemicals solvents bleaches and cleaners because they may affect the screen Also do not use chemically treated cloths The screen is easily damaged so avoid scratching it with hard objects or striking it with a duster or other objects If the stains are serious contact the office detailed
52. in the figure below To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 DESIGN RELATED PARTS DESIGN RELATED PARTS 574 30 201 Marquee Golden Gun 574 30 211 Rear Marquee Golden Gun 574 30 210 Crown Moulding Decal 574 30 209 Side Pnl Decal Monitor Side 574 30 205 Monitor Frame Decal 5714 30 206 Top Bottom 2per Monitor Frame Decal Left Right 2per GLG 2041 LED Panel Octagon 574 30 202 Gun Decal Right Golden Gun 574 30 200 2 Instruction Decal Golden Gun 574 30 203 Gun Decal Left Golden Gun 574 30 207 Button Decal Golden Gun 574 30 204 Front Decal Golden Gun To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PARTS LIST PARTS LIST 1 ELECTRONIC PARTS 837 14572 CONTROL BD 3 838 14988 400 5489 15024 FOR JVS COM 2CH 30W AUDIO AMP ST SW REG VS150E 24 844 00014 01 s ASSYCASE WDA W IGB USA eA IE Cee 400 5483 838 15118 SW REG EADP 130CF A DELTA IC BD GUN 839 1243R CONTROL NEW FUSE BD CTF EDIT DX z R3 2 CONTROL PANEL 838 14973 02 LED BD GUN SENSOR 130 5228 01 91 10 inside cover SPEAKER BOX 4OHM 40W 2per GLG 2100 01 CONTROL UNIT GUN 2per 509 6207 SW OBSA 45UM R IFLED R 12V 2per To Purchase This Machine Please Visit BMI Gaming www
53. in this manual or the point of purchase for this product To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CONTROL UNIT CONTROL UNIT WARNING e Before starting to work be sure to turn the power off Without turning the power off can cause an electric shock or short circuit e Be careful not to damage the wires Damaged wires may cause electric shock or short circuit or present a risk of fire e Exercise due caution in performing soldering procedures If soldering iron is handled carelessly there could be fires or burns N CAUTION e When fastening plastic parts be careful not to tighten screws and nuts excessively Failure to observe this may damage the parts and cause injury due to fragments resulting from damage e After the unit has been disassembled and reassembled again check carefully to be sure that there are no gaps or rattling at the junctions and that the trigger can be operated smoothly If there are gaps or rattling or if operation is not satisfactory the players could get fingers or hands caught resulting in injury e Be sure to inspect control unit surfaces for cracks and damage Players could be injured if they play when the unit is cracked or damaged e Assemble so that there is no gap between the L and R covers If there is a gap or rattling the players could get fingers or hands caught resulting in injury e Do not cut the tie that holds the
54. ing points and pay attention to ensure that the player can enjoy the game safely Non compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine N WARNING Before performing work be sure to turn the power off Performing the work without turning the power off can cause an electric shock or short circuit In the case work should be performed in the status of power on this manual always states to that effect To avoid an electric shock or short circuit do not plug in or unplug quickly To avoid an electric shock do not plug in or unplug with a wet hand Do not expose power cable or earth wires on the surface floor passage etc If exposed the power cable and earth wires are susceptible to damage Damaged cords and wires can cause an electric shock or short circuit To avoid causing a fire or an electric shock do not put things on or damage the power cable When or after installing the product do not unnecessarily pull the power cable If damaged the power cable can cause a fire or an electric shock In case the power cable is damaged ask for a replacement through where the product was purchased from or the office herein stated Using the cord as is damaged can cause fire an electric shock or leakage Be sure to perform grounding appropriately Inappropriate grounding can cause an electric shock Be sure that con
55. ings can cause injury to the fingers while playing Instruct players to remove all accessories that could cause an accident before playing Instruct players that a single control unit is never to be held by 2 or more people during play Otherwise there could be dangerous contact or a collision The control units for use on 1P side left side and 2P side right side are different Ensure that players do not confuse the right and left side Control Units when starting play To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ACCESSORIES ACCESSORIES Confirm that the accessories listed In the table below are present when setting up the product Accessories marked Spare in the note column are consumable items but included as spares Parts not labeled with part numbers are as yet unregistered or cannot be registered Be sure to handle all parts with care as some parts are not available for purchase separately Part name Part no Diagram Use etc Quantity OWNER S MANUAL 574 30 300 1 This manual POWER CABLE DVD SOFTWARE KIT RGW DVDROM GLG To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ACCESSORIES The DVD drive 15 sold separately but it is required in order to install the software for this product If you do not have the drive when installing the product consult the dealer from which you purchased this product
56. ings such as level of game difficulty or mode of the game are adjusted GAME ASSIGNMENTS GAME DIFFICULTY NORMAL ADVERTISE SOUND NORMAL INITIAL LIFE MAX LIFE i RANDOM REVI VAL ON PLAYERI CONTROLLER REACTI ON ON PLAYER2 CONTROLLER REACTI ON ON VOI CE LANGUAGE ENGLI SH CABI NET TYPE EUROPE 3 EXIT SELECT WITH SERVI CE BUTTON AND PRESS TEST BUTTON GAME ASSIGNMENT screen m Controls Use the SERVICE Button to move the cursor to the desired test item Press the TEST Button to change the value of the selected setting Select EXIT and press the TEST Button to return to the GAME TEST MENU screen a Menu Items GAME DIFFICULTY Sets the level of difficulty to one of five levels In order of difficulty VERY EASY gt MEDIUM EASY gt NORMAL gt MEDIUM HARD gt VERY HARD Default setting NORMAL ADVERTISE SOUND Sets the sound level for the advertisements to one of 5 levels from loudest to softest NORMAL gt 3 4 gt 1 2 gt 1 4 gt OFF Default setting NORMAL INITIAL LIFE The number of LIFE s the player will start the game with Can be set between 1 and 9 However cannot be set higher than the MAX LIFE setting Default setting 3 MAX LIFE The maximum amount of LIFE s a player may have Can be set between 1 and 9 Default setting 9 RANDOM REVIVAL Turns RANDOM REVIVAL ON OFF If set to ON two players cannot die at the same time Setting this to ON extends play time but also increases
57. insert power plug into power outlet with earth terminal When using a conversion adapter sold on the market to provide power connect the adaptor s earth wire terminal to an earth terminal that is securely grounded Anas To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ASSEMBLY AND INSTALLATION 6 4 ASSEMBLING CHECK Using TEST MODE verify points such as the proper assembly of the machine Also verify normal operation of the RINGWIDE boards which have been connected and the product s various input and output devices In TEST MODE conduct the tests described below 1 MONITOR TEST When MONITOR TEST is chosen from SYSTEM TEST MENU screen a screen to test the Monitor will be displayed Though the Monitor is pre adjusted at the time of shipment from the factory view the test screen to determine whether or not adjustment is necessary If so refer to Chapter 13 2 DLP PROJECTOR ADJUSTMENT and adjust the Monitor MON TOR TEST 1 2 wasa PRESS TEST BUTTON TO NEXT E PRESS TEST BUTTON TO EXIT 2 SPEAKER TEST When SPEAKER TEST is chosen from SYSTEM TEST MENU screen a screen to test each of the speakers will be displayed The RIGHT SPEAKER and the LEFT SPEAKER are the only speakers which can be checked by just changing their respective settings to ON and OFF SPEAKER TEST L
58. k or short circuit or present a risk of fire 12 1 REMOVING THE CONTROL PANEL 1 Turn the power off i Remove 4 tamper screws Tamper Scres 4 3 Lift the front side of the control panel and then pull the back forward At this point the connector on the back of the control panel is still attached so do not force it To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CONTROL PANEL 4 Disconnect the connector and take the control panel off CONNECTOR 1 Refer to 12 1 REMOVING THE CONTROL PANEL to take the control panel off I Disconnect the connector from the switch NOTE The IP and 2P START buttons are distinguished by a stamp CONNECTOR SM4P Turn the switch about 45 degrees in a counterclockwise direction and pull it out To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CONTROL PANEL 4 Remove the plastic nut and take off the stopper and the button NOTE When ordering a replacement start button order part number 509 6077 BUTTON STOPPER PLASTIC NUT BUTTON STOPPER PLASTIC NUT E SWITCH START BUTTON 509 6077 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 DLP PROJECTOR LCD unit N CAUTION The LCD is adjusted when shipping from the factory Avoid any unnecessary adjustment Fa
59. lease Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ASSEMBLY AND INSTALLATION 21 4 There is an interference prevention wire on the lower level inside the left side front door INTERFERENCE PREVENTION WIRE RMB 60047 Enlargement Refer to Step 2 and work in reverse order to attach the left front door If several of the same type of game machines are to be installed beside each other they should be lined up alternating between ones with the interference prevention wire connected and ones that with the wire removed Be sure to keep the removed interference prevention wire 4 5 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PRECAUTIONS WHEN MOVING THE MACHINE PRECAUTIONS WHEN MOVING THE MACHINE WARNING e When moving the machine be sure to pull out the plug from the power supply Moving the machine with the plug still inserted can cause the power cable to be damaged resulting in a fire and or electric shock When moving the machine on the floor retract the adjusters and ensure that the casters make contact with the floor Pay careful attention so that the casters do not run over power cable and earth wires Damaging the power cable can cause an electric shock and or short circuit When lifting the cabinet be sure to hold the grips and the bottom part Lifting the cabinet by holding other portions may damage parts and installation portions
60. ment of units expendable parts Activities to be carried out by site maintenance personnel Amusement equipment vending machine assembly maintenance inspection and replacement of units expendable parts Other qualified professionals Persons employed by amusement equipment manufacturers or involved in design production testing or maintenance of amusement equipment The individual should have either graduated from technical school or hold similar qualifications in electrical electronics mechanical engineering Activities to be carried out by other qualified professionals Amusement equipment vending machine assembly repair adjustment of electrical electronic mechanical parts Game Version Notation Version numbers appearing in TEST MODE are displayed as asterisks When describing software version upgrades only major version numbers are displayed Minor version and release version numbers are for Sega s administrative use only If you require these numbers please contact the office listed in this document Ver VER Major version Minor version Release version nay be only one digit To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 HANDLING PRECAUTIONS HANDLING PRECAUTIONS When installing or inspecting the machine be very careful of the follow
61. migaming com 800 746 2255 1 561 391 7200 SWITCH UNIT AND COIN METER COIN METER After using a special purpose key to unlock the cashbox door the coin meter can be found at the bottom of the cashbox To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 SYSTEM TEST MODE I SYSTEM TEST MODE IMPORTANT e Go to BOOKKEEPING in GAME TEST MODE to access this product s data e Read the RINGWIDE service manual that comes with the product for details on the SYSTEM TEST MODE However you should perform the settings for this product according to the manual you are reading e The details of changes to TEST MODE settings are saved when you exit from TEST MODE by selecting EXIT from the SYSTEM TEST MODE menu Be careful because if the power is turned off before that point changes to the settings will be lost e Use with the specified settings If settings other than those specified are used inappropriate operations or malfunction may occur In the SYSTEM TEST MODE the main activities include checking RINGWIDE information and actions and the setting of coin credit Also a screen appears for checking screen adjustments For details refer to the RINGWIDE service manual which is provided with the product Press the TEST Button to enter TEST MODE and bring up the SYSTEM TEST MENU screen Use the following settings with this product If the settings are not as specified error messages
62. n Performing work without using the step can cause accidents such as falling down To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ASSEMBLY AND INSTALLATION IMPORTANT Be very careful when handling the DLP projector screen The screen is easily damaged but cannot be repaired If damaged the entire screen must be replaced TOOLS NECESSARY FOR WORK Phillips screwdriver Spanner with variable measuring distance Socets for hexagon bolts and nuts Master key Stepstool To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ASSEMBLY AND INSTALLATION 6 1 ATTACHING THE BILLBOARD Use several steps to perform the assembly work on the top of the machine Lift the 574 50 111 marquee front cover with at least 2 people and set it on top of the LCD from the back Unscrew 4 screws on marquee bracket and insert between back marquee bracket Lift the 574 30 211 rear marquee with at least 2 people and set it on top of the LCD from the back Unscrew 4 screws on marquee bracket and insert between back marquee bracket To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ASSEMBLY AND INSTALLATION N WARNING Be sure to ground the adjusters and secure the product firmly to the installation location If the projector moves either during assembly work or during operati
63. n flickering or blurring as it 1s Using the product with the monitor not properly adjusted may cause dizziness or a headache to an operator a player or the customers When transporting or reselling this product be sure to attach this manual to the product In the case where commercially available monitors and printers are used in this product only the contents relating to this product are explained herein Some commercially available equipment has functions and reactions not stated in this manual Read this manual together with the specific instruction manual of such equipment Descriptions herein contained may be subject to improvement changes without notice The contents described herein are fully prepared with due care However should any question arise or errors be found please contact SEGA INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION Normally at the time of shipment SEGA products are in a status allowing for usage immediately after transporting to the location Nevertheless an irregular situation may occur during transportation Before turning on the power check the following points to ensure that the product has been transported in a satisfactory status Are there any dented portions or defects cuts etc on the external surfaces of the cabinet Are casters and adjusters damaged Do the power supply voltage and frequency requirements meet with those of the location Are all
64. nd or material damage For the safe usage of the product the following pictographs are used Indicates HANDLE WITH CARE In order to protect the human body and equipment this display 1s attached to places where the instruction manual should be referred to Indicates a protective earth terminal Before operating the equipment be sure to connect it to the ground The step may be omitted for products in which a power cable with earth is used Perform work in accordance with the instructions herein stated Instructions for work are explained by paying attention to the aspect of accident prevention Failing to perform work as per the instructions can cause accidents In the case where only those who have technical expertise should perform the work to avoid hazardous situation the instructions herein state that the site maintenance personnel should perform such work Be sure to turn off the power before working on the machine To prevent an electric shock be sure to turn off the power and unplug the power cable before carrying out any work that requires direct contact with the interior of the product If the work 15 to be performed in the power on status the instruction manual herein always states to that effect Be sure to ground the earth terminal This is not required in the case where a power cable with earth is used This product 1s equipped with the earth terminal When installing the product connect the earth terminal to
65. nections such as IC board are made properly Insufficient insertion can cause an electric shock Specification changes removal of equipment conversion and or addition not designated by SEGA are not permitted Failure to observe this may cause a fire or an electric shock Non compliance with this instruction can have a bad influence upon physical conditions of the players or the onlookers or result in injury during play SEGA shall not be held responsible for damage compensation for damage to a third party caused by specification changes not designated by SEGA Do not perform any work or change parts not listed in this manual Doing so may lead to an accident If you need to perform any work not listed in this manual request work from the office indicated in this manual or the point of purchase or inquires for details Be sure to perform periodic maintenance inspections herein stated To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 HANDLING PRECAUTIONS IMPORTANT e For the IC board circuit inspections only the logic tester is allowed The use of a multiple purpose tester is not permitted so be careful in this regard e Static electricity from your body may damage some electronics devices on the IC board Before handling the IC board touch a grounded metallic surface so that the static electricity can be discharged e This product uses a DLP projector DLP projecto
66. on after the completion of assembly a serious accident may occur This product has 4 casters and 4 adjusters After determining the installation location have the adjusters contact the floor directly and adjust them so the machine will remain in a level position keeping a space of about 5 mm between the floor and the casters Move the product to the installation site Hold the grips on the sides of the cabinet when moving it and changing the direction it faces Secure a 200 mm space between the back wall and the back of the cabinet for ventilation Use wrench to set adjuster heights so that the unit will stay level 57 TER After setting turn adjuster nuts upwards to tighten them and secure adjuster heights To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 ASSEMBLY AND INSTALLATION 6 3 CONNECTING THE POWER CABLE AND EARTH N WARNING Use the power supply equipped with an earth leakage breaker Use of power supply without such a breaker could result in fire if there is a current leakage Have available a securely grounded indoor earth terminal This product is equipped with a earth terminal Connect it to a earth terminal in the room with the earth wire Without proper grounding customers could be electrocuted and product operations might not always be stable Do not expose the power cable or earth wire If these are exposed customers could stumble
67. or the Distributor etc where the product was purchased from regarding internal cleaning Using the product with accumulated dust in the interior can cause a fire or accident Note that professional cleaning will require a fee There is the danger of accidents involving electrical shorts circuits or fire caused by factors such as the deterioration of insulation in electrical and electronic equipment over time Check that there are no anomalies such as odors from burning Before starting to work be sure to turn the power off Without turning the power off can cause an electric shock or short circuit Do not clean the product with a water jet or water cannon The product has not been designed for water jet cleaning Water infiltration can cause electric shock or short circuit It will also cause damage that is difficult to repair To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PERIODIC INSPECTION m PERIODIC INSPECTION TABLE ITEMS DESCRIPTION PERIOD REFERENCE contact floor Microswitch test Monthly COIN SELECTOR Coin switch inspection Monthly Coin insertion test Monthly Cleaning Monthly LCD UNIT Screen cleaning Weekly Check screen adjustment Monthly or when 13 2 moving RINGWIDE Memory test Monthly Settings check Monthly Cleaning Every 3 months POWER CABLE Inspection Cleaning year CABINET INTERIOR Cleaning year CABINET SURFACES Cleaning As appropriate
68. ous situation could arise The warning displays are intended for accident prevention for customers and for avoiding hazardous situations relating to maintenance and servicing work Some portions of the cabinet contain high voltage and may cause accidents if touched When performing maintenance be very careful of the warning displays It is especially important that any complex repair and replacement work not mentioned herein should be performed by those technical personnel who have knowledge of electricity and technical expertise In order to prevent accidents caution any customer ignoring the warnings to cease and desist immediately To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PRECAUTIONS REGARDING INSTALLATION LOCATION PRECAUTIONS REGARDING INSTALLATION LOCATION WARNING This product is an indoor game machine Do not install it outside Even indoors avoid installing in places mentioned below so as not to cause a fire electric shock injury and or malfunction Places subject to rain or water leakage or places subject to high humidity in the proximity of an indoor swimming pool and or shower etc Places subject to direct sunlight or places subject to high temperatures in the proximity of heating units etc Places filled with inflammable gas or vicinity of highly inflammable volatile chemicals or hazardous matter Dusty places Sloped or unstable surfaces
69. piral color code The left hand side character shows the base color and the right hand side one the spiral color Example 51 WHITE RED RED WHITE Note 2 The character following the wire color code indicates the size of the wire U AWG16 K AWGIS L AWG20 None AWG22 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 WIRING DIAGRAM 84 WIRING DIAGRAM 0 1 3 D 2 3 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 IR 3 E Jh IER E a a LIT Ts x x ELI m i 211 211 T x x E E T 1 T EE E MT IEE E MT i 21 0 s Ji ait 2 MT rig Jig 1 MT i J n ATI H P las iE mmm m o og LLL Balm m a LI RRR ee e HEH di H E ies ici L To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2
70. proper connections can cause electric shock This work should be carried out by the site maintenance personnel or other qualified professionals Work performed by non technical personnel can cause a severe accident such as electric shock Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation If no one with proper technological expertise is available request service from the office indicated in this document or the point of purchase so as to ensure safety Do not leave power cable earth wires or network cables exposed in areas of heavy foot traffic Doing so may cause them to become damaged possibly resulting in electric shock and or short circuits When laying wiring across the floor always use safety covers to protect the wires Wiring diameter power cable approx 8 mm N CAUTION e Be careful in handling plastic parts Be sure not to tighten screws or nuts too tightly If such parts are exposed to excessive loads or impact they might become damaged resulting in fragments or cracks that could cause accidental injury e When attaching or removing doors or parts be careful that your hand or finger does not get caught in anything e Wear appropriate work clothing so that work can be performed safely Use gloves and safety shoes to prevent accidents or injuries e To perform work safely and securely be sure to prepare a step which is in a secure and stable conditio
71. r screens scratch easily so be careful when cleaning the screen See Chapter 13 DLP PROJECTORS for details e Some parts are not designed and manufactured specifically for this game machine The manufacturers may discontinue or change the specifications of such general purpose parts If this is the case SEGA cannot repair or replace a failed game machine whether or not a warranty period has expired e Do not turn the power on and off continuously Repeatedly turning the power on and off may cause product malfunction or parts damage CONCERNING THE SERIAL NO AND THE ELECTRICAL SPECIFICATIONS DISPLAYS This SEGA product has stickers attached describing the product manufacture No Serial No and Electrical Specifications It also has a Sticker describing where to contact for repair and for purchasing parts When inquiring about or asking for repairs mention the Serial No and Name of Machine indicated on the Sticker The Serial Number indicates the product register Identical machines could have different parts depending on the date of production Also improvements and modifications might have been made after the publication of this manual In order to ensure you order the correct parts mention the Serial No when contacting the applicable places CONCERNING WARNING DISPLAYS This SEGA product has warning displays on stickers labels and or printed instructions adhered attached to or incorporated in the places where a potentially hazard
72. rating can cause a fire and electric shock To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PRECAUTIONS REGARDING INSTALLATION LOCATION Electricity Consumption MAX 46 A Single phase AC 120 V 60 Hz Area i uuu N WARNING e For safe operation use and operate this product in an area measuring at least 2 1 m 82 7 in in width and 2 8 m 110 2 in in depth The area prescribed in this manual is absolutely necessary for if one should fall over and hit their head against something there could be a serious accident e Be sure to provide sufficient space specified in this manual Do not allow objects to block the ventilation ports It can cause generation of heat and a fire e SEGA shall not be held responsible for damage or compensation for damage to a third party resulting from the failure to observe this instruction e The ceiling where this product is installed must be at least 2 4 m 94 5 in high If the ceiling is too low the heat emitted from the product may cause it to catch on fire 2 1m 82 7 in 2 8 m 110 2 in To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PRECAUTIONS REGARDING PRODUCT OPERATION PRECAUTIONS REGARDING PRODUCT OPERATION To avoid injury and trouble be sure to pay attention to the behavior of visitors and players 3 1 BEFORE OPERATION WARNING In or
73. s 72 20 2 CLEANING THE RINGWIDE s 73 20 3 COMPOSITION OF THE RINOM DE L ss 74 DESIGN RELATED PARTS 75 PARTS LIST 76 WIRE COLOR CODE TABLE 83 WIRING DIAGRAM 84 SEGA AMUSEMENTS OFFICES N NO N MM ELE uM uL NO M 16 To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 INTRODUCTION INTRODUCTION This manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies electro mechanicals servicing control spare parts etc for the product SEGA GOLDEN GUN This manual is intended for the owners personnel and managers in charge of operation of the product Operate the product after carefully reading and sufficiently understanding the instructions In the unlikely event that the product does not function correctly DO NOT allow anyone other than a technician to touch the internal system Turn off the power to the machine making sure to unplug the electrical cord from the outlet and contact the office listed below or the point of purchase for this product Use of this product is unlikely to cause physical injuries or damage to property However points that require special attention are indicated by bold text the word IMPORTANT and the symbol below IMPORTANT Indicates important information that if
74. short circuit Be careful not to damage the wires Damaged wires may cause electric shock or short circuit or present a risk of fire e After the cause of circuit protector activation has been removed have the circuit protector re engaged If the unit is used continuously as is there could be heat generation or fire depending on the cause of the activation Have work performed by site maintenance personnel or other qualified individuals Do not allow people without proper knowledge and technical expertise to work on the product Otherwise there could be an electric shock or other serious accident Also customers could be injured while operating the product IMPORTANT If a problem occurs first inspect the connection of any wiring connectors To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLESHOOTING 19 1 TROUBLESHOOTING TABLE With main switch ON no activation No sound is generated from the speaker The control unit sighting is not satisfactory The control unit does not appear to be operating correctly Fluorescent lamp does not illuminate Power is not supplied Securely insert the power plug into the plug socket Power supply voltage is not correct Make sure that power supply voltage is correct After eliminating the cause of overload reinstate the unit s circuit protector lt See 6 8 see below gt Faulty adjustment o
75. the rate of continues Default setting ON PLAYERI PLAYER2 Turns the reaction of player control units ON OFF CONTROLLER REACTION Default setting ON VOICE LANGUAGE Toggles the in game language ENGLISH CHINESE Default setting ENGLISH CABINET TYPE Automatically displays the cabinet type EUROPE ASIA REGION EXP only To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE 11 6 OPTION ASSIGNMENTS Adjust game options m Controls OPTI ASSI GNMENTS PREMIUM START CHANCE ATK POWER 4 LIFE MAGAZINE EXCHANGE CHANCE SCORE CONTI NUE BONUS gt EXIT SELECT WITH SERVI CE BUTTON AND PRESS TEST BUTTON OPTION ASSIGNMENTS screen Use the SERVICE Button to move the cursor to the desired test item Select EXIT and press the TEST Button The GAME TEST MENU screen reappears a Menu Items PREMIUM START CHANCE EXCHANGE CHANCE CONTINUE BONUS Set PREMIUM START CHANCE ON OFF Setting to ON makes the Premium Start menu available at the start of the game credits required Inserting additional credits awards the player bonuses as set below NOTE Cannot be set to ON when set to FREE PLAY Default setting ON ATK POWER The level of ATTACK POWER the player will gain Can be set between and 10 Default setting 2 LIFE The amount of LIFE the player will gain Can be set between 1 and 9 Default setting 1
76. their factory defaults The screen will display COMPLETED Press the TEST Button again to return to the CONTROLLER CALIBRATION SETTING screen Press the SERVICE Button to exit to CONTROLLER CALIBRATION SETTING screen without resetting calibration settings to default To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME TEST MODE 11 8 BACKUP DATA CLEAR Delete various game data BACKUP DATA CLEAR YES CLEAR gt NO CANCEL SELECT W TH SERVI CE BUTTON AND PRESS TEST BUTTON BACKUP DATA CLEAR screen 1 2 BACKUP DATA CLEAR COMPLETED PRESS TEST BUTTON TO EXIT BACKUP DATA CLEAR screen 2 2 m Controls Use the SERVICE Button to move the cursor to the desired test item Select YES CLEAR and press the TEST Button to clear game operational data Once data is cleared the screen will display COMPLETED Press the TEST Button again to return to the GAME TEST MENU screen Select NO CANCEL and press the TEST Button to return to the GAME TEST MENU screen without clearing data To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CONTROL PANEL CONTROL PANEL N WARNING e Before starting to work be sure to turn the power off Without turning the power off can cause an electric shock or short circuit e Be careful not to damage the wires Damaged wires may cause electric shoc
77. vances item prices go up by 10 In 2 player mode items cost 70 of the price they are in 1 player mode Weapons permanent effect Attack Power Up 1 Magazine 1 Fast Reload Weapons limited use Machine Gun 6 sec Shot Gun 6 sec T Piercing Ammo 1 Missile 1 mltems one time use Enemy Weakener 41 Life 1 mitc Mystery Ball To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME DESCRIPTION EVENTS Various events occur in the course of the game such as Shoot the arch to block enemies Battle your secret rival Shoot down the incoming energy balls and Shoot the driver of the car A Shoot prompt appears on screen telling the player to shoot the target objects marked with red circles Fire in the holen k Emir Er w EVENT screen If the player succeeds he she can get a score bonus 1000 pts and sometimes avoid enemy attacks If the player fails he she will have to battle many enemies or be forced to take damage BATTLES WITH BOSSES A unique boss awaits the player at the end of each stage Their weak points are revealed in the form of on screen prompts PLEASE WAPT BOSS BATTLE START screen WEAK POINT PROMPT To Purchase This Machine Please Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME DESCRIPTION BOSS BATTLE SCREEN Attacking the

Download Pdf Manuals

Related Search

golden gun video arc.. golden gun arcade game what is the golden gun the man with the golden gun youtube videos of golden arrow

Related Contents

  Ansmann Happy Dreamer  1410 Écureuil  Samsung HE10T User's Manual  Betriebsanleitung - SUNNY BOY 1.5 / 2.5  Bushnell 11-8322 Binoculars User Manual  User manual - MESHING  WDA 71400 - Waschtrockner - service  Mode d`emploi testo 340  G-SAH Manual de Instruções  

Copyright © All rights reserved. Failed to retrieve file