Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement
Contents
1. Disconnect the communications power cable from its socket labeled J50 in the service manual only pull on the connector itself and not the socket This connection is very tight work the connector slowly and gently iFixit CC BY NC SA www iFixit com Page 10 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Unplug the large USB connector from its socket labeled J8 in the service manual Step 20 Press the tab on the ethernet cable and unplug it from its socket labeled J9 in the service manual iFixit CC BY NC SA www iFixit com Page 11 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 21 G The following connector requires two hands to disconnect Flip the rear case over and lay it on its back to gain access to the power Supply cable Step 22 The power supply cable is secured by an interlocking connector that must be held open to unplug the connector G Insert the flat end of a soudger down into the power supply cover between the socket clip and the power supply connector iFixit CC BY NC SA www iFixit com Page 12 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 23 Grasp the power supply cable firmly and lift both it and the spudger from the channel in the power supply housing to unplug the connector Step 24 Module Disconnect the USB cable from the module For t2. connector Squeeze the side tabs until the connector releases Always grasp the cable by the connector Do not pull on the cable itself Pull the connector away from the connector port gt e gt a Grasp the temperature probe and pull it up to remove it from the monitor iFixit CC BY NC SA www iFixit com Page 3 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 5 Remove the cover of the temperature module by pressing the tab and sliding the cover to the right Step 6 Depress the spring tab on the temperature probe cable connector and withdraw it from the probe port iFixit CC BY NC SA www iFixit com Page 4 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 7 Remove the flathead screw on the USB networking door Loosen the captive Phillips 2 screw securing the monitor to the stand Holding the monitor securely open the USB networking door G You may have to lift the monitor slightly to allow the door to swing out from the stand mount iFixit CC BY NC SA www iFixit com Page 5 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 9 Detach any accessory USB cables from USB ports on the monitor Step 10 Slide the monitor off of the stand tray iFixit CC BY NC SA www iFixit com Page 6 of 14 Welch Allyn Connex Vital Signs Monitor 6000 M
3. Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement iF ixiT Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Replace or add a new module to your Connex vital signs module INTRODUCTION Use this guide to remove or replace a vital signs module from a Connex monitor This guide shows to procedure to remove a module from a standard chassis The procedure can be repeated to remove the second module from the standard chassis and the third module from an extended chassis PLEASE NOTE This repair guide was developed by the iFixit team based on Welch Allyn s own service manual Neither iFixit nor this repair guide is endorsed by or affiliated with Welch Allyn TOOLS Coin 1 Flathead Screwdriver 1 Phillips 2 Screwdriver 1 iFixit CC BY NC SA www iFixit com Page 1 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 1 Stand Unplug the AC power connection cable Step 2 Place your thumb and forefinger on the blood pressure NIBP hose connector Squeeze the side tabs until the connector releases Always grasp the hose by the connector Do not pull on the hose itself Pull the connector away from the connector port iFixit CC BY NC SA www iFixit com Page 2 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 3 Place your thumb and forefinger on the Pulse oximetry SpO2 or combined SpO2 SpHb cable
4. he extended chassis Disconnect the two USB cables from the module Step 25 Remove the USB cable from the retaining clip on the module iFixit CC BY NC SA www iFixit com Page 13 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 26 Slide the module out of the case G Repeat the above procedure to remove any additional modules trom the chassis During reassembly install the module closest to the display first Reinsert modules into the housing with the serial number label facing up To reassemble your device follow these instructions in reverse order This document was last generated on 2015 05 10 03 28 30 AM iFixit CC BY NC SA www iFixit com Page 14 of 14
5. odule Replacement Step 11 Battery G Place the monitor upside down on a clean surface Insert a coin into the slot and push to open Choose a coin that fits comfortably into the slot Remove the battery cover Step 12 Use the plastic label to remove the battery from its recess iFixit CC BY NC SA www iFixit com Page 7 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 13 Rear Housing Open the communications door to access the lower left hand rear housing screw Remove the four Phillips 2 screws labeled 14 in the service manual from the rear housing Step 14 With the handle alert bar facing you begin to lift the rear housing from the left side holding the right side securely NDo not attempt to separate the rear housing from the monitor it is still attached with several cables iFixit CC BY NC SA www iFixit com Page 8 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 15 G Support the rear housing while you disconnect the cables in the following steps Disconnect the fan cable labeled connector A in the service manual from its socket in the power supply iFixit CC BY NC SA www iFixit com Page 9 of 14 Welch Allyn Connex Vital Signs Monitor 6000 Module Replacement Step 17 Unplug the small USB connector from its socket labeled J4 in the service manual Step 18
Download Pdf Manuals
Related Search